SECTION1614 CABLETRAYS

Size: px
Start display at page:

Download "SECTION1614 CABLETRAYS"

Transcription

1 SECTION1614 CABLETRAYS PART 1 GENERAL 1.01 SECTION INCLUDES A. Cable trays and accessories RELATED SECTIONS 1.03 REFERENCES A. ANSI/NFPA 70 - National Electrical Code. B. ASTM A123 - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products. C. ASTM A653 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process. D. NEMA VE Metal Cable Tray Systems E. NEMA VE Metal Cable Tray Installation Guidelines 1.04 ABBREVIATIONS A. Cable Tray Abbreviations: The following abbreviations are used in this section and on the drawings: 1. ASTM American Society of Testing and Materials 2. NEMA National Electrical Manufacturers Association 3. NEC National Electrical Code 4. U.L Underwriters Laboratory 5. ALUM Aluminum 6. HDGAF Hot Dipped Galvanized After Fabrication 7. PGSTL Milled Galvanized Steel 8. S.S. Stainless Steel 1.05 SUBMITTALS A. Submit under provisions of Section B. Shop Drawings: Indicate Cablofil part numbers, tray type, dimensions, NEMA class, support points, and finishes. C. Product Data: Provide data for fittings and accessories.

2 D. Manufacturer's Instructions: Indicate application conditions and limitations of use stipulated by product testing agency specified under Regulatory Requirements. Include instructions for storage, handling, protection, examination, preparation, installation, and starting of Product PROJECT RECORD DOCUMENTS A. Submit under provisions of Section B. Record actual routing of cable tray and locations of supports. PART 2 PRODUCTS 2.01 MANUFACTURERS A. Manufacturer: All cable trays shall be manufactured by Cablofil or engineer-approved equal. For location of nearest manufacturers representative, contact Cablofil at or on the world wide web at B. Cable Tray Types 1. Center Hung Type Tray: A prefabricated metal structure consisting of one longitudinal rail with individual rungs. Standard manufacturer ladder tray selections shall include full width and half width bottom rung configurations. a. Length of Straight Sections: Actual lengths and quantities shall be as indicated on drawings. Standard manufacturer lengths shall be 10 ft (actual 118-1/2 inch) or 12 ft (actual 142-1/2 inch) not including connectors if attached. Straight section lengths shall be greater than or equal to the support span length. Straight section lengths shall be used such that a maximum of one splice joint is between any two tray supports. b. Tray Widths: Actual widths shall be as indicated on drawings. Standard manufacturer widths shall be in accordance with NEMA Standard VE1 Section and shall be 6, 9, 12, 18, 24 inches. c. Center Rail Height: Actual tray center rail shall be 1-1/2 inch wide hollow tube by 3.76 inches high. Center rail shall be aluminum alloy d. Rungs: Rungs shall be minimum 5/8 inch wide by 5/8 inch deep hollow tube with reinforcing rib as specified by manufacturer. Rungs shall be attached to center rail by welding. Each rung shall be welded in minimum 2 places per manufacturer's specifications. Attachment of standard tray rungs to center rail shall not be by mechanical means. Rungs shall be aluminum alloy e. Rung Height: Rung heights shall be 3, 4, or 6 inches and as specified on drawings. Standard manufacturer rung heights shall be in accordance with NEMA Standard VE1 Section f. Rung Spacing: Rung spacing on straight tray sections shall be 6, 9, or 12 inches on center and as indicated on drawings. Standard manufacturer rung spacing on straight sections shall be 6, 9, or 12 inches. Distance between rungs on fittings shall not exceed rung spacing and tolerances for straight tray. g. Tray Fittings: Tray fitting types and quantities shall be as indicated on the drawings. All tray fittings shall be constructed of same material as straight tray sections.

3 h. Working (Allowable ) Load Capacity: Working load capacity and span shall be in accordance with NEMA Standard VE1 Sections 4.8, 5.2 and Table 1. Tray deflection shall not exceed manufacturers published engineering data for project cable tray working load capacity and minimum support span requirements. i. Safety Factor: Minimum load capacity safety factor shall be 1.5 in accordance with NEMA Standard VE1 Section j. Materials: All cable tray sections, fittings and accessories shall be made from corrosion resistant metal or metal with a factory applied corrosion resistant finish. All materials shall be as indicated on drawings and in accordance with NEMA Standard VE1 Sections 4.1 and ) Aluminum (ALUM.): Cable tray rails and rungs shall be constructed from copper free alloy type All fittings and accessories shall be constructed from corrosion resistant aluminum alloy that is compatible with alloy 6063 such as type 5052 or type k. Connectors: Connector splice shall have less than ohms electrical resistance. Expansion connectors shall provide for minimum 1" tray expansion and shall be placed as shown on drawings or as required to prevent damage to the tray system from thermal expansion and contraction. Grounding bonding jumpers shall be installed at all expansion connectors. Each straight tray section shall be supplied with one tray connector with hardware at no charge. l. Connector Hardware: 3/8 inch diameter hex bolt and serrated-face flanged hex nut which does not need a washer. Connector hardware finish shall be protected against corrosion. Connector hardware finish shall be zinc plated. m. Grounding: Provide continuous ground from cable tray to building ground in accordance with Grounding section of specifications. The cable tray system shall be capable of being is used as equipment grounding conductor in accordance with the National Electric Code (NEC) Article 392-7(b). Cable tray sections and fittings shall be marked to show the minimum cross sectional area in accordance with the National Electric Code (NEC) Article Bonding jumpers shall be constructed of laminated aluminum or insulated copper wire with a minimum of 1000 rated amperes or as indicated on drawings in accordance with NEC Ladder Type Tray: A prefabricated metal structure consisting of two longitudinal side members connected by individual transverse members or individual rungs. Standard manufacturer ladder tray selections shall include both flange in and flange out configurations. a. Length of Straight Sections: Actual lengths and quantities shall be as indicated on drawings. Standard manufacturer lengths shall be 12 ft or 20 ft not including connectors if attached. Straight section lengths shall be greater than or equal to the support span length. Straight section lengths shall be used such that a maximum of one splice joint is between any two tray supports. b. Widths: Actual widths shall be as indicated on drawings. Standard manufacturer widths shall be in accordance with NEMA Standard VE1 Section and shall be 6, 9, 12, 18, 24, 30, 36 inches. c. Side Rail Height: Actual tray side rail height shall be {4, 5, 6, 7} inches and as indicated on drawings. Standard manufacturer heights shall be in accordance with NEMA Standard VE1 Section and shall be {4, 5, 6, 7} inches.

4 d. Side Channels: Side channel members to be of 'C' channel configuration. Top flange shall be minimum 1 or 1-3/4 inches as specified in manufacturers catalog. e. Rungs: Rungs shall be minimum 1 inch wide as specified by manufacturer. Rungs shall be attached to side rails by welding. Attachment of rungs to side rails shall not be by mechanical means. Rungs shall be constructed from same material as side rails. f. Rung Spacing: Rung spacing on straight tray sections shall be {6, 9, 12} inches on center and as indicated on drawings. Standard manufacturer rung spacing on straight sections shall be 6, 9, 12. Distance between rungs on fittings shall not exceed rung spacing and tolerances for straight tray and shall be measured at the center of the fitting. g. Tray Fittings: Tray fittings types and quantities shall be as indicated on the drawings. All tray fittings shall be constructed of same material as straight tray sections. Tangent sections of tray fittings shall be at least 2 inches for NEMA class 12A,12B,12C. Tangent sections of tray fittings shall be at least 5 inches for NEMA class 20A,20B,20C. Manufacturer tray fittings shall include the following minimum standard fittings types: 1) Horizontal elbow fittings in 30, 45, 60, and 90 degree angles. 2) Vertical elbow fittings in 30, 45, 60 and 90 degree angles with inside and outside radius options. 3) Horizontal adjustable elbow fittings with adjustable angle. 4) Horizontal and vertical tee fittings, branch at 90 degree angle. 5) Horizontal wye fittings, branch at 45 degree angle. 6) Horizontal and vertical cross fittings, branch at 90 degree angles. 7) Horizontal reducers A) Straight type: Reducer fitting has two symmetrical offsets from the centerline of the fitting. B) Right hand type: Reducer fitting when viewed from large tray width side, has straight side on right. C) Left hand type : Reducer fitting when viewed from large tray width side, has straight side on left. 8) Fitting Radius: The nominal bend radius of all fittings shall be {12, 24, 36} inches as measured on the smallest side as indicated on the drawings and shall be appropriate for the allowable bending radius of the cables to be installed in the fitting. Standard manufacturers fitting radii in accordance with NEMA Standard VE1 shall be 12, 24, 36, and 48 inch. h. Working ( Allowable ) Load Capacity: Working load capacity and span shall be in accordance with NEMA Standard VE1 Sections 4.8, 5.2, and Table 1. NEMA Load/Class designation shall be (12A, 12B, 12C, 20A, 20B, 20C} and as indicated on drawings. Tray deflection shall not exceed manufacturers published engineering data for project cable tray working load capacity and minimum support span

5 requirements. i. Safety Factor: Minimum load capacity safety factor shall be 1.5 in accordance with NEMA Standard VE1 Section j. Materials: All cable tray sections, fittings and accessories shall be made from corrosion resistant metal or metal with a factory applied corrosion resistant finish. All materials shall be as indicated on drawings and in accordance with NEMA Standard VE1 Sections 4.1 and ) Mill Galvanized (PGSTL): Mill galvanized coatings shall be applied at the steel mill in accordance with ASTM specification A924 and in accordance with ASTM Publication No ) Hot Dipped Galvanized after fabrication (HDGAF): Hot dipped galvanized after fabrication shall be applied in accordance with ASTM Publication No. A123. k. Connectors: Connector splice shall have less than ohms electrical resistance. Expansion connectors shall provide for minimum 1" tray expansion and shall be placed as shown on drawings or as required to prevent damage to the tray system from thermal expansion and contraction. Grounding bonding jumpers shall be installed at all adjustable connectors and expansion connectors. l. Connector Hardware: 3/8" diameter, truss head, ribbed neck steel screw with phillips recess and a free spinning, lock type steel nut which does not need a washer. Connector hardware finish shall be protected against corrosion. Connector hardware shall be {cadmium plated steel with yellow chromate finish per ASTM B766, Class 5, Type 2, Type 316 Stainless Steel}. m. Grounding: Provide continuous ground from section to section and from cable tray to building ground in accordance with Grounding section of specifications. The cable tray system shall be capable of being is used as equipment grounding conductor in accordance with the National Electric Code (NEC) Article 392-7(b). Cable tray sections and fittings shall be marked to show the minimum cross sectional area in accordance with the National Electric Code (NEC) Article Bonding jumpers shall be constructed of laminated aluminum or insulated copper wire with a minimum of 200 rated amperes or as indicated on drawings in accordance with NEC Trough Type Tray: A fabricated metal structure greater than 4 inches in width consisting of integral or separate longitudinal side rails and a bottom having openings sufficient for the passage of air. a. Length of Straight Sections: Actual lengths and quantities shall be as indicated on drawings. Standard manufacturer lengths shall be 12 ft or 20 ft not including connectors if attached. Straight section lengths shall be greater than or equal to the support span length. Straight section lengths shall be used such that a maximum of one splice joint is between any two tray supports. b. Widths: Actual widths shall be as indicated on drawings. Standard manufacturer widths shall be in accordance with NEMA Standard VE1 Section and shall be 6, 9, 12, 18, 24, 30, 36 inches. c. Side Rail Height: Actual tray side rail height shall be {4, 5, 6, 7} inches and as indicated on drawings. Standard manufacturer heights shall be in accordance with NEMA Standard VE1 Section and shall be {4, 5, 6, 7} inches.

6 d. Transverse Elements: The maximum open spacing between transverse elements shall be 4 inches measured in the direction parallel to the side rails. e. Rung Style Troughs: Standard manufacturer rung spacing on straight sections shall be 4 inch wide channels on 8 inch centers for aluminum trays and 1-1/4 wide rungs on 5 centers for steel trays. Rung spacing on fittings shall be on 5 inch centers. Rungs shall be attached to side rails by welding. f. Ventilated, Corrugated Bottom Style Troughs: Standard manufacturer bottoms shall include ventilated corrugated bottoms welded to the side rails. Standard ventilation slots shall be 3/8" wide by 1-1/4" long spaced on 1-1/2" centers across the tray width and located 2.19" on center along the tray length. Corrugated bottom shall be 0.5" high with 0.875" top cable supporting ribs spaced on 2.19" centers along tray length. g. Tray Fittings: Tray fittings types and quantities shall be as indicated on the drawings. All tray fittings shall be constructed of same material as straight tray sections. Manufacturer tray fittings shall include the following minimum standard fittings types: 1) Horizontal elbow fittings in 30, 45, 60, and 90 degree angles. 2) Vertical elbow fittings in 30, 45, 60 and 90 degree angles with inside and outside radius options. 3) Horizontal adjustable elbow fittings with adjustable angle. 4) Horizontal and vertical tee fittings, branch at 90 degree angle. 5) Horizontal wye fittings, branch at 45 degree angle. 6) Horizontal and vertical cross fittings, branch at 90 degree angles. 7) Horizontal reducers A) Straight type: Reducer fitting has two symmetrical offsets from the centerline of the fitting. B) Right hand type: Reducer fitting when viewed from large tray width side, has straight side on right. C) Left hand type : Reducer fitting when viewed from large tray width side, has straight side on left. h. Fitting Radius: The nominal bend radius of all fittings shall be 12 inches as measured on the smallest side as indicated on the drawings and shall be appropriate for the allowable bending radius of the cables to be installed in the fitting. Standard manufacturers fitting radii in accordance with Working ( Allowable ) Load Capacity: i. Working (Allowable ) Load Capacity: Working load capacity shall be in accordance with NEMA Standard VE1 Sections 4.8, 5.2, and Table 1. NEMA Load/Class designation shall be (12A, 12B, 12C, 20A, 20B, 20C} and as indicated on drawings. Tray deflection shall not exceed manufacturers published engineering data for project cable tray working load capacity and minimum support span requirements.

7 j. Safety Factor: Minimum load capacity safety factor shall be 1.5 in accordance with NEMA Standard VE1 Section k. Materials: All cable tray sections, fittings and accessories shall be made from corrosion resistant metal or metal with a factory applied corrosion resistant finish. All materials shall be as indicated on drawings and in accordance with NEMA Standard VE1 Sections 4.1 and ) Mill Galvanized (PGSTL): Mill galvanized coatings shall be applied at the steel mill in accordance with ASTM specification A924 and in accordance with ASTM Publication No P.W. system numbers 05-2C31 shall be mill galvanized steel. 2) Hot Dipped Galvanized after fabrication (HDGAF): Hot dipped galvanized after fabrication shall be applied in accordance with ASTM Publication No. A123. P.W. system numbers 05-1C31 shall be hot dipped galvanized after fabrication steel. 3) Aluminum (ALUM.): Cable tray straight section side rails shall be constructed from copper free alloy type 6063-T6. All fittings and accessories shall be constructed from corrosion resistant aluminum alloy that is compatible with alloy 6063 such as type 5052 or type l. Connectors: Connector splice shall have less than ohms electrical resistance. Expansion connectors shall provide for minimum 1" tray expansion and shall be placed as shown on drawings or as required to prevent damage to the tray system from thermal expansion and contraction. Grounding bonding jumpers shall be installed at all adjustable connectors and expansion connectors. m. Connector Hardware: 3/8" diameter, truss head, ribbed neck steel screw with phillips recess and a free spinning, lock type steel nut which does not need a washer. Connector hardware finish shall be protected against corrosion. Connector hardware shall be {cadmium plated steel with yellow chromate finish per ASTM B766, Class 5, Type 2, Type 316 Stainless Steel}. n. Grounding: Provide continuous ground from section to section and from cable tray to building ground in accordance with Grounding section of specifications. The cable tray system shall be capable of being is used as equipment grounding conductor in accordance with the National Electric Code (NEC) Article 392-7(b). Cable tray sections and fittings shall be marked to show the minimum cross sectional area in accordance with the National Electric Code (NEC) Article Bonding jumpers shall be constructed of laminated aluminum or insulated copper wire with a minimum of 200 rated amperes or as indicated on drawings in accordance with NEC Corrugated Solid Bottom Type Tray: A prefabricated metal structure consisting of a solid bottom with no openings within an integral or two separate longitudinal side rails. Corrugated tray bottoms shall have no more than 1-5/16 inch space between corrugations.. a. Length of Straight Sections: Actual lengths and quantities shall be as indicated on drawings. Standard manufacturer lengths shall be 12 ft or 20 ft not including connectors if attached. Straight section lengths shall be greater than or equal to the support span length. Straight section lengths shall be used such that a maximum of one splice joint is between any two tray supports.

8 b. Widths: Actual widths shall be as indicated on drawings. Standard manufacturer widths shall be in accordance with NEMA Standard VE1 Section and shall be 6, 9, 12, 18, 24, 30, 36 inches. c. Side Rail Height: Actual tray side rail height shall be {4, 5, 6, 7} inches and as indicated on drawings. Standard manufacturer heights shall be in accordance with NEMA Standard VE1 Section and shall be {4, 5, 6, 7} inches. d. Side Channels: Side channel members to be of 'C' channel configuration. Top flange shall be minimum 1 or 1-3/4 inches as specified in manufacturers catalog. e. Bottoms: Standard manufacturer bottoms shall include solid corrugated bottoms welded to the side rails. Corrugated bottom shall be 0.5" high with 0.875" top cable supporting ribs spaced on 2.19" centers along tray length. f. Tray Fittings: Tray fittings types and quantities shall be as indicated on the drawings. All tray fittings shall be constructed of same material as straight tray sections. Manufacturer tray fittings shall include the following minimum standard fittings types: 1) Horizontal elbow fittings in 30, 45, 60, and 90 degree angles. 2) Vertical elbow fittings in 30, 45, 60 and 90 degree angles with inside and outside radius options. 3) Horizontal adjustable elbow fittings with adjustable angle. 4) Horizontal and vertical tee fittings, branch at 90 degree angle. 5) Horizontal wye fittings, branch at 45 degree angle. 6) Horizontal and vertical cross fittings, branch at 90 degree angles. 7) Horizontal reducers A) Straight type: Reducer fitting has two symmetrical offsets from the centerline of the fitting. B) Right hand type: Reducer fitting when viewed from large tray width side, has straight side on right. C) Left hand type : Reducer fitting when viewed from large tray width side, has straight side on left. 8) Fitting Radius: The nominal bend radius of all fittings shall be 12 inches as measured on the smallest side as indicated on the drawings and shall be appropriate for the allowable bending radius of the cables to be installed in the fitting. Standard manufacturers fitting radii in accordance with NEMA Standard VE1 shall be 12, 24, 36, and 48 inch. g. Working (Allowable ) Load Capacity: Working load capacity shall be in accordance with NEMA Standard VE1 Sections 4.8, 5.2, and Table 1. NEMA Load/Class designation shall be (12A, 12B, 12C, 20A, 20B, 20C} and as indicated on drawings. Tray deflection shall not exceed manufacturers published engineering data for project cable tray working load capacity and minimum support span requirements.

9 h. Safety Factor: Minimum load capacity safety factor shall be 1.5 in accordance with NEMA Standard VE1 Section i. Materials: All cable tray sections, fittings and accessories shall be made from corrosion resistant metal or metal with a factory applied corrosion resistant finish. All materials shall be as indicated on drawings and in accordance with NEMA Standard VE1 Sections 4.1 and ) Mill Galvanized (PGSTL): Mill galvanized coatings shall be applied at the steel mill in accordance with ASTM specification A924 and in accordance with ASTM Publication No P.W. system numbers B360 shall be mill galvanized steel. 2) Hot Dipped Galvanized after fabrication (HDGAF): Hot dipped galvanized after fabrication shall be applied in accordance with ASTM Publication No. A123. P.W. system numbers A360 shall be hot dipped galvanized after fabrication steel. 3) Aluminum (ALUM.): Cable tray straight section side rails shall be constructed from copper free alloy type 6063-T6. All fittings and accessories shall be constructed from corrosion resistant aluminum alloy that is compatible with alloy 6063 such as type 5052 or type P.W. system numbers 5720 shall be aluminum. j. Connectors: Connector splice shall have less than ohms electrical resistance. Expansion connectors shall provide for minimum 1" tray expansion and shall be placed as shown on drawings or as required to prevent damage to the tray system from thermal expansion and contraction. Grounding bonding jumpers shall be installed at all adjustable connectors and expansion connectors. k. Connector Hardware: 3/8" diameter, truss head, ribbed neck steel screw with phillips recess and a free spinning, lock type steel nut which does not need a washer. Connector hardware finish shall be protected against corrosion. Connector hardware shall be {cadmium plated steel with yellow chromate finish per ASTM B766, Class 5, Type 2, Type 316 Stainless Steel}. l. Grounding: Provide continuous ground from section to section and from cable tray to building ground in accordance with Grounding section of specifications. The cable tray system shall be capable of being is used as equipment grounding conductor in accordance with the National Electric Code (NEC) Article 392-7(b). Cable tray sections and fittings shall be marked to show the minimum cross sectional area in accordance with the National Electric Code (NEC) Article Bonding jumpers shall be constructed of laminated aluminum or insulated copper wire with a minimum of 200 rated amperes or as indicated on drawings in accordance with NEC Channel Type Tray: A prefabricated metal structure consisting of a one piece ventilated bottom or solid bottom channel section, or both, not exceeding 6 inches in width. a. Length of Straight Sections: Actual lengths shall be as indicated on drawings. Standard manufacturer lengths shall be 12 ft long not including connectors if attached. b. Widths: Actual widths shall be as indicated on drawings. Standard manufacturer widths shall be 3, 4, 6 inches.

10 c. Outside Depths: Actual depths shall be as indicated on drawings. Standard manufacturer depths shall be 1-3/4 inches. d. Channel Fittings: Channel fittings types and quantities shall be as indicated on the drawings. All channel fittings shall be constructed of same material as straight tray sections. Tangent sections of channel fittings shall be at least 2 inches. Manufacturer tray fittings shall include the following minimum standard fittings types: 1) Horizontal elbow fittings in 30, 45, 60, and 90 degree angles. 2) Vertical elbow fittings in 30, 45, 60 and 90 degree angles with inside and outside radius options. 3) Horizontal tee fittings, branch at 90 degree angle. 4) Horizontal cross fittings, branch at 90 degree angles. e. Fitting Radius: The nominal bend radius of all fittings shall be 12 inches as measured on the smallest side and as indicated on the drawings. Standard manufacturers fitting radii in accordance with NEMA Standard VE1 shall be 12, 24, and 36 inch. f. Materials: All cable tray sections, fittings and accessories shall be made from corrosion resistant metal or metal with a factory applied corrosion resistant finish. All materials shall be as indicated on drawings and in accordance with NEMA Standard VE1 Section ) Mill Galvanized (PGSTL): Mill galvanized coatings shall be applied at the steel mill in accordance with ASTM specification A924 and in accordance with ASTM Publication No P.W. system numbers shall be mill galvanized steel. 2) Hot Dipped Galvanized after fabrication (HDGAF): Hot dipped galvanized after fabrication shall be applied in accordance with ASTM Publication No. A123. P.W. system numbers shall be hot dipped galvanized after fabrication steel. 3) Aluminum (ALUM.): Cable tray straight section side rails shall be constructed from copper free alloy type 6063-T6. All fittings and accessories shall be constructed from corrosion resistant aluminum alloy that is compatible with alloy 6063 such as type 5052 or type P.W. system numbers shall be aluminum. g. Connectors: Expansion connectors shall provide for minimum 1" Channel expansion and shall be placed as shown on drawings or as required to prevent damage to the tray system from thermal expansion and contraction. Grounding bonding jumpers shall be installed at all adjustable connectors and expansion connectors. h. Connector Hardware: 3/8" diameter, truss head, ribbed neck steel screw with phillips recess and a free spinning, lock type steel nut which does not need a washer. Connector hardware finish shall be protected against corrosion. Connector hardware shall be {cadmium plated steel with yellow chromate finish per ASTM B766, Class 5, Type 2, Type 316 Stainless Steel}.

11 6. Accessories PART 3 EXECUTION 3.01 INSTALLATION a. Covers: Tray covers shall be provided as indicated on drawings. Covers for fittings shall be available in same configuration as covers for straight tray. Covers for tray shall be supplied of the same material as straight tray and fittings or as indicated on drawings. Manufacturers standard tray covers shall include flat covers with no side flanges, flat covers with side flanges, louvered flat covers with no side flanges, louvered flat covers with side flanges, and 15 degree peaked covers with side flanges. Provide standard manufacturer's hardware as required to hold covers to cable tray sections. "Clip Type" clamps may be used on indoor, horizontal cable trays. Heavy duty "Strap Type" clamps shall be used on all outdoor and vertical cable tray sections. b. Divider Strips: Divider strips shall be provided as indicated on drawings. Divider strips shall be attached to cable tray rungs in the field with standard manufacturer supplied hardware. Divider strips shall be supplied of the same material as straight tray and fittings or as indicated on drawings. c. Blind End Plates: Blind end plates shall be provided as indicated on drawings. Blind end plates shall be supplied of the same material as straight tray and fittings or as indicated on drawings. d. Cable Dropouts: Cable dropouts shall be provided as indicated on drawings. Cable dropouts shall be supplied of the same material as straight tray and fittings or as indicated on drawings. e. Wall Penetration Sleeves: Provide wall penetration sleeves for all wall penetrations where indicated on drawings. Wall penetration sleeves shall be fabricated from steel, hot dipped galvanized after fabrication material per ASTM A-123. The penetration sleeve shall be designed for a single run of cable tray in standard overall tray widths and overall tray depths. In fire rated locations, install Hilti firestop blocks in sufficient quantities to meet maximum 2 hour wall fire rating. f. Conduit and Pipe Clamps: Provide standard manufacturer designed conduit and pipe clamps and/or brackets as required by code to clamp conduit and pipe. A. Install in accordance with manufacturer's instructions. B. Install metallic cable tray in accordance with NEMA Standards Publications VE1and VE2 and as indicated on drawings. C. Provide cable tray supports at locations as shown in NEMA Standard VE2 and maintain spacing between supports of { } feet maximum. D. Elevation: Straight cable tray, fittings, and accessories shall be at height from the floor to the bottom of the cable tray { } feet and as indicated on the drawings. E. Use expansion connectors where required. ENDOFSECTION

SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS

SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 GENERAL 1.01 DESCRIPTION A. The work covered by this section of the Specifications includes all labor necessary to perform and complete such

More information

CT-02 CABLE TRAY SYSTEMS

CT-02 CABLE TRAY SYSTEMS CT-02 CABLE TRAY SYSTEMS SYSTEMS THAT MAKE SENSE Introduction B-Line Systems was formed in 96 and has over 30 years experience manufacturing cable tray systems in which it has grown to become the industry

More information

Cat. No. Material Siderail Height. Designed to lock into place for easy alignment and installation. ABW-4-SSP

Cat. No. Material Siderail Height. Designed to lock into place for easy alignment and installation. ABW-4-SSP Metallic Snap-In Splice Plate Designed to lock into place for easy alignment and installation. Packaged in pairs with zinc plated hardware. Provided as standard with each straight and fitting. Cat. No.

More information

SECTION 260536 - CABLE TRAYS. A. Continuous, rigid, welded steel or stainless steel wire mesh cable management system.

SECTION 260536 - CABLE TRAYS. A. Continuous, rigid, welded steel or stainless steel wire mesh cable management system. SECTION 260536 - CABLE TRAYS PART 1 - GENERAL SECTION INCLUDES: A. Continuous, rigid, welded steel or stainless steel wire mesh cable management system. B. Cable tray systems are defined to include, but

More information

T&B Cable Tray. Metallic Aluminum. Straight Lengths. Tray Bottom Types Ladder, Ventilated and Solid Trough

T&B Cable Tray. Metallic Aluminum. Straight Lengths. Tray Bottom Types Ladder, Ventilated and Solid Trough Tray Bottom Types Ladder Extra wide aluminum rungs are welded to extruded aluminum I-beam siderails. Every second rung is reversed to allow for easy top or bottom mounting of cable ties and clamps. All

More information

SECTION 4: Cable Ladder Stainless Steel & Aluminium

SECTION 4: Cable Ladder Stainless Steel & Aluminium SECTION 4: Cable Ladder & Aluminium Type 3/50 (NEMA 6A) Type 4/70L Type 5/112 (NEMA 20C) > 4:3 > 4:4 > 4:5 Aluminium Type 4/70A (NEMA 16B) Ladder Splice Plates > 4:7 > 3:18 Page 4:1 Cable Ladder General

More information

PW Cable Tray Ladder, Trough & Solid Bottom

PW Cable Tray Ladder, Trough & Solid Bottom PW Cable ray adder, rough & Solid Bottom Metallic Covers & Cover Connectors Covers protect and contain cables. hey are highly recommended to avoid damage to the tray contents and to protect against the

More information

SECTION 15140 - PIPE HANGERS AND SUPPORTS

SECTION 15140 - PIPE HANGERS AND SUPPORTS Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the

More information

Cable Runways & Accessories

Cable Runways & Accessories SB17U SB13AL SB17 SB17T SB117 SB17HRB SB2107 SB2101A SB17VRB SB2110A SB2129 SB2129SD SB130 SB2221 SB126 SB2118 SB119 SB2105 113 Cooper B-Line manufactures a wide variety of high quality cable pathway products

More information

Cable ladder installation at S.C.M. Chemicals Limited s titanium dioxide Plant in Western Australia

Cable ladder installation at S.C.M. Chemicals Limited s titanium dioxide Plant in Western Australia Exel Composites Cable Support Systems offer engineers a structural product for solving many design and plant engineering problems, enabling long term reliable support of expensive and often critical cables.

More information

Cable Support Solutions

Cable Support Solutions Cable Support Solutions B-Line by Eaton Technology Day Japan 2013 2012 Eaton Corporation. All rights reserved. 2012 Eaton Corporation. All rights reserved. 2012 Eaton Corporation. All rights reserved.

More information

Series 1 Steel Cable Ladder

Series 1 Steel Cable Ladder able Straight Sections See pages LDS-3 & LDS-4 Straight Section overs See page LDS-10 ccessories See pages LDS-5 - LDS-9 Fittings See pages LDS-11 - LDS-17 Fitting overs See page LDS-10 LDS-1 able Support

More information

TARIFF CODE and updates standard

TARIFF CODE and updates standard TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of

More information

HOUSTON COMMUNITY COLLEGE HCC ALIEF CAMPUS MAIN BUILDING, FIRST, SECOND & FOURTH FLOORS RENOVATION ISSUE DATE: 10.17.12

HOUSTON COMMUNITY COLLEGE HCC ALIEF CAMPUS MAIN BUILDING, FIRST, SECOND & FOURTH FLOORS RENOVATION ISSUE DATE: 10.17.12 SECTION 27 05 26 - GROUNDING AND BONDING FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes grounding and bonding products, design requirements and installation for communications

More information

CABLE TRAY. Introduction

CABLE TRAY. Introduction Introduction BLE TRAY ICMS cable tray system including Fittings and accessories is manufactured with return flange in a standard length of 2.44Mtr, according to the following specifications and standards:

More information

SECTION 25110 TELECOMMUNICATION ROOMS

SECTION 25110 TELECOMMUNICATION ROOMS PART 1 - GENERAL 1.1 SUMMARY A. SCOPE SECTION 25110 TELECOMMUNICATION ROOMS 1. This section includes the minimum installation requirements for equipment and cabling infrastructure in Telecommunication

More information

Dock Hardware & Accessory Products Catalog

Dock Hardware & Accessory Products Catalog Dock Hardware & Accessory Products Catalog Product Page # Product Page # Angle Brackets/Clips 8 Back Up Plate 5 Backing Plate/Hurricane Stop 10 Carriage Bolt Sets 4 Chain Retainer 10 Connector Pin Set

More information

Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049

Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049 Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal

More information

Preformed Metal Roofing and Siding

Preformed Metal Roofing and Siding Page -1-1. GENERAL 1.1. Description This specification along with the drawings covers the furnishing of all material, products, equipment, accessories, tools, services, transportation, labor and supervision

More information

SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS

SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes seismic restraints and other earthquake-damage-reduction measures for electrical

More information

AN IN-DEPTH LOOK AT 2011 NEC ARTICLE 392 - CABLE TRAY. (The following code explanations are to be used with a copy of the 2011 NEC.

AN IN-DEPTH LOOK AT 2011 NEC ARTICLE 392 - CABLE TRAY. (The following code explanations are to be used with a copy of the 2011 NEC. AN IN-DEPTH LOOK AT 2011 NEC ARTICLE 392 - CABLE TRAY (The following code explanations are to be used with a copy of the 2011 NEC.) To obtain a copy of the NEC contact: National Fire Protection Association

More information

Safely Installing, Maintaining and Inspecting Cable Trays

Safely Installing, Maintaining and Inspecting Cable Trays Purpose U.S. Department of Labor Occupational Safety and Health Administration Directorate of Technical Support & Emergency Management Office of Technical Programs and Coordination Activities Safely Installing,

More information

PART 1 GENERAL 1.1 SECTION INCLUDES

PART 1 GENERAL 1.1 SECTION INCLUDES J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including

More information

STANDARD SPECIFICATIONS SECTION 05500 METAL FABRICATIONS

STANDARD SPECIFICATIONS SECTION 05500 METAL FABRICATIONS STANDARD SPECIFICATIONS SECTION 05500 METAL FABRICATIONS PART 1 GENERAL 1.1 DESCRIPTION A. Section includes requirements for providing metal fabricated items like castings, gratings, hatchways, ladders,

More information

Guidelines for Earthquake Bracing of Residential Water Heaters

Guidelines for Earthquake Bracing of Residential Water Heaters Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)

More information

Policy on Water Heater Installations Policy No. UPC 510-1-94 Effective: September 1, 1995 Revised: February 10, 1996

Policy on Water Heater Installations Policy No. UPC 510-1-94 Effective: September 1, 1995 Revised: February 10, 1996 CITY OF SAN JOSE BUILDING DIVISION POLICY Policy on Water Heater Installations Policy No. UPC 510-1-94 Effective: September 1, 1995 Revised: February 10, 1996 All new and replacement water heaters installed

More information

ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES

ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES PART 1 - GENERAL 1.1 SCOPE OF WORK SECTION 06610 FIBERGLASS REINFORCED PLASTICS (FRP) FABRICATIONS PULTRUDED SQUARE TUBE LADDER

More information

NEMA Standards Publication VE 2-2000. Cable Tray Installation Guidelines

NEMA Standards Publication VE 2-2000. Cable Tray Installation Guidelines NEMA Standards Publication VE 2-2000 Cable Tray Installation Guidelines Published by: National Electrical Manufacturers Association 1300 North 17th Street Rosslyn, VA 22209 Approved by: Cable Tray Institute

More information

ONTRAC WIRE MESH CABLE TRAY SYSTEM

ONTRAC WIRE MESH CABLE TRAY SYSTEM P R O D U C T D ATA S H E E T ONTRAC WIRE MESH CABLE TRAY SYSTEM K E Y F E AT U R E S Available in two styles: Shaped and Standard Tray Easy to use pathway solution that supports large quantities of network

More information

All work must conform to the National Electric Code, latest edition, and all other applicable codes and regulations.

All work must conform to the National Electric Code, latest edition, and all other applicable codes and regulations. DIVISION 16 ELECTRICAL SECTION 16100 - ELECTRICAL PART 1 - GENERAL SCOPE All electrical work as shown on the drawings and as necessary to provide a complete electrical system. Include primary service,

More information

Partitioning & Ceiling Product Information

Partitioning & Ceiling Product Information Partitioning & Ceiling Product Information tel + 44 (0) 1384 412448 fax + 44 (0) 1384 4494 email enquiries@drywallsteelsections.co.uk web www.drywallsteelsections.co.uk tel + 44 (0) 1384 412448 fax + 44

More information

CONTENTS. Yale University Design Standards. Underground Electrical Duct Bank. A. Summary. B. System Design and Performance Requirements

CONTENTS. Yale University Design Standards. Underground Electrical Duct Bank. A. Summary. B. System Design and Performance Requirements 16600 Underground Electrical Duct Bank This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications

More information

SECTION 15410 GROUND WATER STORAGE TANKS

SECTION 15410 GROUND WATER STORAGE TANKS SECTION 15410 GROUND WATER STORAGE TANKS PART 1 GENERAL.01 SCOPE A. Section Includes Requirements for designing, fabricating, and erecting a welded steel ground storage tank..02 SYSTEM DESCRIPTION A. Design

More information

CLEAR-DIVISIONS APERTO

CLEAR-DIVISIONS APERTO CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the

More information

NORTH ORANGE COUNTY COMMUNITY COLLEGE DISTRICT SECTION 27 05 26 GROUNDING AND BONDING FOR COMMUNICATION SYSTEMS

NORTH ORANGE COUNTY COMMUNITY COLLEGE DISTRICT SECTION 27 05 26 GROUNDING AND BONDING FOR COMMUNICATION SYSTEMS SECTION GROUNDING AND BONDING FOR COMMUNICATION SYSTEMS RELATED SECTIONS: Section 27 00 00 General Requirements Section 27 02 00 Communication General Requirements Section 27 05 28 Pathways for Communications

More information

Flextray - Installation. Installation

Flextray - Installation. Installation 50 Flextray Cutters Part Qty./Box Wt./Box Number lbs. kg CLEANSHEAR Cleanshear 1 4.3 1.95 Cutting Tool Exclusive, patented Cleanshear cuts tray fast No sharp edges Designed specifically for cutting Flextray

More information

Cable Trays Technical Instructions & Specifications

Cable Trays Technical Instructions & Specifications Cable Trays Technical Instructions & Specifications Products Catalogue Objective and Structure The company s main objective is the supply of quality products, with respect to: practical design increased

More information

SECTION 16110 CONDUITS, RACEWAYS, FITTINGS AND CABLE TRAYS

SECTION 16110 CONDUITS, RACEWAYS, FITTINGS AND CABLE TRAYS SECTION 16110 CONDUITS, RACEWAYS, FITTINGS AND CABLE TRAYS PART 1 - GENERAL 1.01 REQUIREMENTS A. The general provisions of the Contract, including General and Supplementary Conditions and General Requirements,

More information

Specifications for Lightning Protection. ASAE Engineering Practice

Specifications for Lightning Protection. ASAE Engineering Practice Chapter 8: Lightning Specifications for Lightning Protection ASAE safety standards are not laws. They are recommended voluntary standards used by designers, engineers, manufacturers and users of the equipment,

More information

SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT

SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Equipment

More information

The National Armored Cable Manufacturers Association Presents. Installation Standard for Types AC and MC Cables

The National Armored Cable Manufacturers Association Presents. Installation Standard for Types AC and MC Cables The National Armored Cable Manufacturers Association Presents Installation Standard for Types AC and MC Cables An ANSI Standard Original document jointly produced by NECA and NACMA as Standard for Installing

More information

Guidelines for Earthquake Bracing Residential Water Heaters

Guidelines for Earthquake Bracing Residential Water Heaters Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the

More information

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel

More information

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2

More information

MAST ARMS & POLES. Ornamental Pole Top & Bases

MAST ARMS & POLES. Ornamental Pole Top & Bases Ornamental Pole Top & Bases Pelco s decorative pole top and bases help make the traffic signal aesthetically pleasing to the eye. Available for various pole diameters and multiple finish options. Ornamental

More information

SECTION 11014 WINDOW WASHING SYSTEMS

SECTION 11014 WINDOW WASHING SYSTEMS SECTION 11014 WINDOW WASHING SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section includes, but is not limited to, design and furnishing portable davits, davit sleeves, dvit bases, four (4) removable outriggers,

More information

EMI/RFI Shielded Cable Tray

EMI/RFI Shielded Cable Tray EMI/RFI Cable Tray Chalfant began supplying industry cable tray in 1948 and designed and developed the first RF Tray for NS in 196 when it became imperative to protect instrument and control cabling from

More information

Cable Tray Ladder, Trough, Channel, Under Floor, Shielded CH-115C

Cable Tray Ladder, Trough, Channel, Under Floor, Shielded CH-115C Cable Tray Ladder, Trough, Channel, Under Floor, Shielded CH-11C Chalfant dvantages Why Chalfant? Chalfant knows its success over the past 7 years can be traced to providing more than just quality cable

More information

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE

More information

INSTRUCTIONS AND PARTS LIST SINGLE GIRDER UNDERHUNG CRANE BRIDGE KITS 1/2 THRU 10 TON HAND GEARED AND MOTOR DRIVEN

INSTRUCTIONS AND PARTS LIST SINGLE GIRDER UNDERHUNG CRANE BRIDGE KITS 1/2 THRU 10 TON HAND GEARED AND MOTOR DRIVEN INSTRUCTIONS AND PARTS LIST SINGLE GIRDER UNDERHUNG CRANE BRIDGE KITS 1/2 THRU 10 TON HAND GEARED AND MOTOR DRIVEN JUNE, 1999 COPYRIGHT 1999, Columbus Mckinnon Corporation PART NO. 113533-71 Page 1 COLUMBUS

More information

C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S

C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S January 2009 Issue 6 Valu Guide Brackets The Ultimate in Adjustability and Cost Savings Valu Guide brackets are part of a family

More information

Valu Guide Sheaths. Valu Guide Inserts. Optional Valu Guide Inserts. Typical Properties of Valu Guide Rail. and Hardware.

Valu Guide Sheaths. Valu Guide Inserts. Optional Valu Guide Inserts. Typical Properties of Valu Guide Rail. and Hardware. 14 gauge stainless steel The Original, Long Life Sanitary Guide Rail Valu Guide rail incorporates two outstanding materials: stainless steel and UHMW. The 14 ga. stainless steel sheath provides rigid streamlined

More information

SERIES ASM NEOPRENE/EPMD FLANGED SINGLE SPHERE CONNECTOR CONNECTORS. Pressures to 225 PSIG (15.51 barg) Temperatures to 230ºF (110ºC)

SERIES ASM NEOPRENE/EPMD FLANGED SINGLE SPHERE CONNECTOR CONNECTORS. Pressures to 225 PSIG (15.51 barg) Temperatures to 230ºF (110ºC) APPLICATIONS Process Industry Weak Acids Alkalies Compressed Air Pulp & Paper MODELS ASM - Flanged Connection OPTIONS Control Rods Oil & Gas Water & Waste Pump suction & discharge Sea water Chemical lines

More information

ANTENNA PARTS CATALOG

ANTENNA PARTS CATALOG ANTENNA PARTS CATALOG Maco Antennas 302 S. East St. Mt. Carroll, IL 61053 www.macoantennas.net 815-244-3500 www.antennapartsoutlet.com SCREWS / BOLTS PART SIZE LENGTH DESCRIPTION PRICE S21 10-24 1/2" Machine

More information

Cable Installation Accessories. Cable Hoisting and Attachment. Snap-In Hangers. SnapStak Hangers

Cable Installation Accessories. Cable Hoisting and Attachment. Snap-In Hangers. SnapStak Hangers SnapStak Hangers New design increases stack height SnapStak hangers have become the industry standard for maximizing space utilization on crowded towers and now that utility is further expanded with the

More information

METER REQUIREMENTS GENERAL REQUIREMENTS SECTION D

METER REQUIREMENTS GENERAL REQUIREMENTS SECTION D 12 - ELECTRIC SERVICE HANDBOOK SECTION D METER REQUIREMENTS This chapter gives you information on Central Lincoln s metering requirements. It's divided into three sections: General requirements This section

More information

4 Installation Requirements

4 Installation Requirements 4 Installation Requirements 9 4.1 Code Reference The authority having jurisdiction should be referenced to determine what law, ordinance or code shall apply in the use of flexible duct. Ducts conforming

More information

Cable/Conduit Conversion

Cable/Conduit Conversion Cable/Conduit Conversion Busway can be used in many applications where cable and conduit are more commonly used. The question arises, Why use busway instead of conventional cable and conduit? Benefits

More information

Cabinets 101: Configuring A Network Or Server Cabinet

Cabinets 101: Configuring A Network Or Server Cabinet Cabinets 101: Configuring A Network Or Server Cabinet North, South and Central America White Paper May 2012 www.commscope.com Contents Background Information 3 What is a network or server cabinet? 3 What

More information

POWERS Controls No. 4 Pneumatic Damper Actuator

POWERS Controls No. 4 Pneumatic Damper Actuator POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000

More information

Conduit Fittings & Accessories Directional Drilling Conduit Utility Duct Telephone Duct Residential Boxes

Conduit Fittings & Accessories Directional Drilling Conduit Utility Duct Telephone Duct Residential Boxes CANTEX INC. 301 Commerce Ste 2700 Fort Worth, Texas 76102 817-215-7000 Fax: 817-215-7001 Conduit Fittings & Accessories Directional Drilling Conduit Utility Duct Telephone Duct Residential Boxes YOUR FULL

More information

SECTION 08 5656 GUARDA SECURITY WINDOW SCREENS

SECTION 08 5656 GUARDA SECURITY WINDOW SCREENS Page 1 of 5 SECTION 08 5656 GUARDA SECURITY WINDOW SCREENS Guarda Security Window Screens in this specification are appropriate for use in windows, storefronts, curtain walls, vents, and any other applications

More information

Cat. No. Finishes & Materials. Standard Finish: Electrogalvanized. Change suffix to SS6(C).

Cat. No. Finishes & Materials. Standard Finish: Electrogalvanized. Change suffix to SS6(C). Superstrut Support Systems 1-5/8 in. x 1-5/8 in. Channel and Hardware Superstrut 1-5/8 in. x 1-5/8 in. - 12 Gauge Channel Type A Solid Base Punched Description Solid base -P Punched -HS Half slots Half

More information

Power Cube Open Source Ecology Page 1. Power Cube. Version 4

Power Cube Open Source Ecology Page 1. Power Cube. Version 4 Power Cube Open Source Ecology Page 1 Power Cube Version 4 Power Cube Open Source Ecology Page 2 Contents Table of Contents Power Cube... 1 Contents...2 Introduction... 3 Bill Of Materials...4 Discrete

More information

SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK

SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. This section covers the pre-finished, pre-fabricated Architectural standing seam roof system. All metal trim,

More information

AIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM):

AIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM): SECTION 02832 AIRPORT SECURITY FENCING PART 1-GENERAL 1.1 SUMMARY A. Section includes: Construct airport security chain-link fence and gate at specified areas and conforming lines, grades, details indicated

More information

RPS - sales@rpssolar.com - 858 755 4505-12478 San Bruno Cove, San Diego, CA 92130

RPS - sales@rpssolar.com - 858 755 4505-12478 San Bruno Cove, San Diego, CA 92130 RPS - sales@rpssolar.com - 858 755 4505-2478 San Bruno Cove, San Diego, CA 9230 SWH Solar Mount Rail R-MR-SW-SR-0.5, R-MR-SW-SR-2, R-MR-SW-SR-4, R-MR-SW-SR-4B, R-MR-SW-SR-7 Part No. MR-SW-SR-0.5, MR-SW-SR-2,

More information

METHOD STATEMENT FOR INSTALLATION OF CABLE TRAY/TRUNKING/LADDER

METHOD STATEMENT FOR INSTALLATION OF CABLE TRAY/TRUNKING/LADDER Page 1 of 6 FOR INSTALLATION OF CABLE TRAY/TRUNKING/LADDER 0 Issued for Review & Comments Rev. Date Description Eng. A.H Prepared by Checked by Approved by Page 2 of 6 REVISION CONTROL SHEET REV. NO. DATE

More information

CLEAR-DIVISIONS CENTERFOLD

CLEAR-DIVISIONS CENTERFOLD CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in

More information

2013 Edition. Flanged fittings 30"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61

2013 Edition. Flanged fittings 30-64 NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61 30"-64" Ductile Iron industrial Applications, water & Wastewater 2 Table of Contents Flanged Fittings for Water 3 Flange Details 5 Flanged Fittings 6 90º and 45º Bend 6 22-1/2º and 11-1/4º Bends 7 Tees

More information

SECTION 22 LIGHTNING PROTECTION SYSTEM

SECTION 22 LIGHTNING PROTECTION SYSTEM SECTION 22 LIGHTNING PROTECTION SYSTEM 22.01 SCOPE: A. These Specifications shall form a part of the Contract Documents and shall govern construction work for all buildings to be built or modified for

More information

INDEX 02 : CABLE LADDERS

INDEX 02 : CABLE LADDERS 02-01 INDEX 02 : CABLE LADDERS Part No. Part No. Part No. Part No. Part No. ACS ORIGINALSTRUT ; CABLE LADDER - STEEL GENERAL INFORMATION LGBE8O0 02-11 LGTE8300 02-12 LGER80 02-13 LGLR5O450300 02-14 Cable

More information

RAIL FREE SOLAR ROOF MOUNT

RAIL FREE SOLAR ROOF MOUNT RAIL FREE SOLAR ROOF MOUNT Utilizes EcoFasten Solar s patented technology Rock-it system Designed with the installer in mind. EcoFasten Solar specializes in solar roof attachments that are the easiest

More information

Residential Deck Safety, Construction, and Repair

Residential Deck Safety, Construction, and Repair Juneau Permit Center, 4 th Floor Marine View Center, (907)586-0770 This handout is designed to help you build your deck to comply with the 2006 International Residential Building code as modified by the

More information

security products metric sizes Redefine your comfort zone. www.titus-hvac.com

security products metric sizes Redefine your comfort zone. www.titus-hvac.com metric sizes secure lethal objects monitoring areas suicide deterrent Redefine your comfort zone. www.titus-hvac.com humid areas prevents corrosion minimum security medium security maximum security Table

More information

Requirements for the Attachment of Communication Cable Facilities on PPL Poles

Requirements for the Attachment of Communication Cable Facilities on PPL Poles Page 99 of 137 Requirements for the Attachment of Communication Cable Facilities on Replaces: URS-3002 URS-3004 URS-101C-304 A-157649 Page 100 of 137 Reference Notes for Drawings: General 1. The term communication

More information

TS 813 GROUNDING AND BONDING TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET GROUNDING

TS 813 GROUNDING AND BONDING TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET GROUNDING TORONTO TRANSPORTATION January 2012 TS 813 GROUNDING AND BONDING TABLE OF CONTENTS 1. DRAWINGS TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET

More information

CTI TECHNICAL BULLETIN Number 9: A publication of the Cable Tray Institute

CTI TECHNICAL BULLETIN Number 9: A publication of the Cable Tray Institute CTI TECHNICAL BULLETIN Number 9: A publication of the Cable Tray Institute Cable Tray Wiring Systems Have Many Cost Advantages Cost is usually a major consideration in the selection of a wiring system.

More information

Chapter 73 Articles of iron or steel

Chapter 73 Articles of iron or steel Notes. Chapter 73 Articles of iron or steel 1.- In this Chapter the expression cast iron applies to products obtained by casting in which iron predominates by weight over each of the other elements and

More information

CDGRD-10. Grounding. Solutions For Comm/Data Applications

CDGRD-10. Grounding. Solutions For Comm/Data Applications CDGRD-10 Grounding Solutions For Comm/Data Applications Overview & Table of Contents Cooper B-Line s Grounding products for rack & runway provide a complete solution for grounding metal supports. The offering

More information

CLEAR-DIVISIONS VARIOFOLD

CLEAR-DIVISIONS VARIOFOLD CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the

More information

BOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping.

BOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping. BOQ SPECIFICATIONS VERTICAL BLINDS Vertical Blinds made of glass fibre fabrics in width 5 (or 4 ). Minimum overlapping of ¾ in fabric. Top aluminium anodized rail of 1.4 mm thickness. 2 inch wide channel

More information

Please check with your local inspection authority for any additional requirements before installation.

Please check with your local inspection authority for any additional requirements before installation. Specifications for Residential Overhead Electric Service Installation This brochure addresses most typical residential overhead service installations. Variances for the following specifications must be

More information

STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM

STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM Chapter 9 STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM 9.1 BACKGROUND Steel is widely used in the construction of multi-storey buildings. However, steel construction is seldom used and is traditionally

More information

SYSTEM 1850-SE SERVICE ENTRANCE CABLE SYSTEM

SYSTEM 1850-SE SERVICE ENTRANCE CABLE SYSTEM Pyrotenax SYSTEM 1850-SE SERVICE ENTRANCE CABLE SYSTEM Contents Introduction This section provides an overview of general circuit design considerations and installation guidelines for a Pyrotenax System

More information

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate

More information

Hose Clamps & Fittings

Hose Clamps & Fittings All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw

More information

GUIDELINES FOR UTILITY INSTALLATIONS Part 1 - Wire Lines and Communications Cables

GUIDELINES FOR UTILITY INSTALLATIONS Part 1 - Wire Lines and Communications Cables Engineering Department SEPTEMBER, 2007 GUIDELINES FOR UTILITY INSTALLATIONS Part 1 - Wire Lines and Communications Cables General Requirements This section applies to all public and private utilities,

More information

Cable Tray Straight Sections Pages 5-11. Fittings Pages 10-17. Inside Vertical Bends. 90 Page 1-12 60 Page 1-13 45 Page 1-14 30 Page 1-15

Cable Tray Straight Sections Pages 5-11. Fittings Pages 10-17. Inside Vertical Bends. 90 Page 1-12 60 Page 1-13 45 Page 1-14 30 Page 1-15 Tray When metal ladder cable trays came of age, they were used to support the new armored shielded power cables that were permitted outside the conduit environment. Utilities and industrial companies initiated

More information

INSTALLATION INSTRUCTIONS HUSTLER 4-BTV, 5-BTV TRAP VERTICAL WARNING INSTALLATION OF THIS PRODUCT NEAR POWER LINES IS DANGEROUS

INSTALLATION INSTRUCTIONS HUSTLER 4-BTV, 5-BTV TRAP VERTICAL WARNING INSTALLATION OF THIS PRODUCT NEAR POWER LINES IS DANGEROUS INSTALLATION INSTRUCTIONS HUSTLER 4-BTV, 5-BTV TRAP VERTICAL WARNING INSTALLATION OF THIS PRODUCT NEAR POWER LINES IS DANGEROUS FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS GENERAL DESCRIPTION:

More information

F-Series Camera Mounting Accessories

F-Series Camera Mounting Accessories F-Series Camera Mounting Accessories Document Number: 427-0462-00-12 Version: 100 Issue Date: September 2010 2010. All rights reserved worldwide. FLIR Commercial Systems, Inc. 70 Castilian Drive Goleta,

More information

2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property

2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property 2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property A brief summary of the most used code references for residential wiring State of Idaho Division of Building Safety Electrical

More information

REQUEST FOR QUOTE. Material $ Labor/Installation $ tax $ Total $ Material $ Labor/Installation $ tax $ Total $

REQUEST FOR QUOTE. Material $ Labor/Installation $ tax $ Total $ Material $ Labor/Installation $ tax $ Total $ REQUEST FOR QUOTE Specifications- Knightdale Station Park Naming Rights Exterior Signage General Conditions 1. Delivery of signs to be within 6 weeks of order confirmation. 2. Shop drawings are required

More information

LHD LINEAR HEAT D ETECTIONN

LHD LINEAR HEAT D ETECTIONN Tri-Metallic Core: Steel provides tensile strength Copper increase conductivity Tin for corrosion resistance LHD LINEAR HEAT D ETECTIONN TECHNICAL DATA Temperature Rating: 155 F (68 C) (typical temperature)

More information

DIVISION 27 COMMUNICATIONS. A. System design shall be completed by a Registered Communications Distribution Designer (RCDD).

DIVISION 27 COMMUNICATIONS. A. System design shall be completed by a Registered Communications Distribution Designer (RCDD). DIVISION 27 COMMUNICATIONS 27 00 00 COMMUNICATIONS A. System design shall be completed by a Registered Communications Distribution Designer (RCDD). B. Comply with American National Standards Institute

More information

ELECTRIC METERING COMMERCIAL & INDUSTRIAL

ELECTRIC METERING COMMERCIAL & INDUSTRIAL ELECTRIC METERING COMMERCIAL & 1.0 INDEX 1.0 INDEX 2.0 SCOPE 3.0 GENERAL REQUIREMENTS 4.0 METER LOCATIONS 5.0 UNDERGROUND TERMINATIONS 6.0 METERING TRANSFORMER ENCLOSURES 7.0 SINGLE CUSTOMER METER INSTALLATIONS

More information

SMA Interface Mating Dimensions (Per MIL-STD-348)

SMA Interface Mating Dimensions (Per MIL-STD-348) SMA Series SMA 6 SMA Interface Mating Dimensions (Per MIL-STD-348) SMA Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.250 6.35.263 6.68.. B.1790 4.55.1808

More information

Rittal s Comprehensive Family Of... NETWORK RACK SOLUTIONS

Rittal s Comprehensive Family Of... NETWORK RACK SOLUTIONS Rittal s Comprehensive Family Of... NETWORK RACK SOLUTIONS STANDARD & ECONOMICAL BasicRack A complete low-cost, high-quality basic equipment management system. Design Six web channel holes per side allow

More information