New Structured Light Projection and Image Processing Sensor. Phoenix

Transcription

1 New Structured Light Projection and Image Processing Sensor Phoenix

2 THE NEW PHOENIX ALL IN ONE The revolution in optical measurement Measurement of geometric elements and surface analysis with only one sensor With the new Phoenix, WENZEL has perfomed pioneering development work in optical measurement technology. The new optical, non-contact 3D sensor captures point clouds and geometry elements on different materials in one working cycle. It can be used in automatic probe changers alongside tactile sensors, so that multiple applications can be performed with a single measuring system. These multiple and flexible applications and many other highlights make the Phoenix the ideal tool for quality assurance, production monitoring and analysis. Typical application areas of the Phoenix are in the automotive industry, but also in plastic and sheet metal processing. Previously timeconsuming inspections can be done quickly and reliably especially in mass production, such as in car body, sheet metal or plastic part production. Its small, lightweight design allows the sensor to be fitted to standard 3D coordinate measuring machines in production lines and metrology rooms. Accurate Results for Different Materials, Colours and Finishes. The sensor enables the detection and measurement of mixed materials such as carbon fiber reinforced plastics combined with aluminum and sheet metal.. The sensor parameters can be adjusted to suit the material.. The Phoenix has the ability to recognize different textured surfaces, to diagnose defects such as scratches and even to collect barcodes for process control.. The sensor is relatively insensitive to extraneous light High measuring productivity and multi-sensor operation. Information from gray scale images and 3D point clouds are determined, saved and analyzed in one common coordinate system with high resolution.. Within a very short time all the necessary data of the measurement object can be recorded.. The new Phoenix is fully integrated into WENZEL software packages. Due to its light weight it can be fitted to the PH10 motorized indexing head and the PHS servo positioning head from Renishaw.. All system components integrate perfectly because CMM, sensor and software are developed, produced and maintained by WENZEL. and delivers reliable results almost independently of the ambient lighting conditions.. The Phoenix can record data from work pieces with different colors and with different surface texture. At a glance Phoenix measuring process. Multi-colored components and small, rough and flexible work pieces can be easily measured. Multi-Sensor Operation and Automatic Exchange. In multi-sensor operation, the advantages of the optical sensor Phoenix can be combined with the advantages of tactile measuring systems. Both technologies can be used independently or together. With Renishaw ACR1, ACR2 and ACR3 probe changers the sensors can be automatically exchanged. Existing CMM systems can easily be retrofitted with Phoenix.

3 THE NEW PHOENIX ALL IN ONE The revolution in optical measurement Measurement of geometric elements and surface analysis with only one sensor With the new Phoenix, WENZEL has perfomed pioneering development work in optical measurement technology. The new optical, non-contact 3D sensor captures point clouds and geometry elements on different materials in one working cycle. It can be used in automatic probe changers alongside tactile sensors, so that multiple applications can be performed with a single measuring system. These multiple and flexible applications and many other highlights make the Phoenix the ideal tool for quality assurance, production monitoring and analysis. Typical application areas of the Phoenix are in the automotive industry, but also in plastic and sheet metal processing. Previously timeconsuming inspections can be done quickly and reliably especially in mass production, such as in car body, sheet metal or plastic part production. Its small, lightweight design allows the sensor to be fitted to standard 3D coordinate measuring machines in production lines and metrology rooms. Accurate Results for Different Materials, Colours and Finishes. The sensor enables the detection and measurement of mixed materials such as carbon fiber reinforced plastics combined with aluminum and sheet metal.. The sensor parameters can be adjusted to suit the material.. The Phoenix has the ability to recognize different textured surfaces, to diagnose defects such as scratches and even to collect barcodes for process control.. The sensor is relatively insensitive to extraneous light High measuring productivity and multi-sensor operation. Information from gray scale images and 3D point clouds are determined, saved and analyzed in one common coordinate system with high resolution.. Within a very short time all the necessary data of the measurement object can be recorded.. The new Phoenix is fully integrated into WENZEL software packages. Due to its light weight it can be fitted to the PH10 motorized indexing head and the PHS servo positioning head from Renishaw.. All system components integrate perfectly because CMM, sensor and software are developed, produced and maintained by WENZEL. and delivers reliable results almost independently of the ambient lighting conditions.. The Phoenix can record data from work pieces with different colors and with different surface texture. At a glance Phoenix measuring process. Multi-colored components and small, rough and flexible work pieces can be easily measured. Multi-Sensor Operation and Automatic Exchange. In multi-sensor operation, the advantages of the optical sensor Phoenix can be combined with the advantages of tactile measuring systems. Both technologies can be used independently or together. With Renishaw ACR1, ACR2 and ACR3 probe changers the sensors can be automatically exchanged. Existing CMM systems can easily be retrofitted with Phoenix.

4 THE NEW PHOENIX ALL IN ONE The revolution in optical measurement Measurement of geometric elements and surface analysis with only one sensor With the new Phoenix, WENZEL has perfomed pioneering development work in optical measurement technology. The new optical, non-contact 3D sensor captures point clouds and geometry elements on different materials in one working cycle. It can be used in automatic probe changers alongside tactile sensors, so that multiple applications can be performed with a single measuring system. These multiple and flexible applications and many other highlights make the Phoenix the ideal tool for quality assurance, production monitoring and analysis. Typical application areas of the Phoenix are in the automotive industry, but also in plastic and sheet metal processing. Previously timeconsuming inspections can be done quickly and reliably especially in mass production, such as in car body, sheet metal or plastic part production. Its small, lightweight design allows the sensor to be fitted to standard 3D coordinate measuring machines in production lines and metrology rooms. Accurate Results for Different Materials, Colours and Finishes. The sensor enables the detection and measurement of mixed materials such as carbon fiber reinforced plastics combined with aluminum and sheet metal.. The sensor parameters can be adjusted to suit the material.. The Phoenix has the ability to recognize different textured surfaces, to diagnose defects such as scratches and even to collect barcodes for process control.. The sensor is relatively insensitive to extraneous light High measuring productivity and multi-sensor operation. Information from gray scale images and 3D point clouds are determined, saved and analyzed in one common coordinate system with high resolution.. Within a very short time all the necessary data of the measurement object can be recorded.. The new Phoenix is fully integrated into WENZEL software packages. Due to its light weight it can be fitted to the PH10 motorized indexing head and the PHS servo positioning head from Renishaw.. All system components integrate perfectly because CMM, sensor and software are developed, produced and maintained by WENZEL. and delivers reliable results almost independently of the ambient lighting conditions.. The Phoenix can record data from work pieces with different colors and with different surface texture. At a glance Phoenix measuring process. Multi-colored components and small, rough and flexible work pieces can be easily measured. Multi-Sensor Operation and Automatic Exchange. In multi-sensor operation, the advantages of the optical sensor Phoenix can be combined with the advantages of tactile measuring systems. Both technologies can be used independently or together. With Renishaw ACR1, ACR2 and ACR3 probe changers the sensors can be automatically exchanged. Existing CMM systems can easily be retrofitted with Phoenix.

5 UNIQUE FUNCTIONALITY The combined Solution The Phoenix uses a unique combination of methods for evaluating the measurement data. Firstly, the phase-shift method using structured light projection and secondly, an image processing method is used for 3D measurement of features, for example circles. By simultaneous use of both of these methods the measurement of very thin-walled component features as in sheet metal and stamped parts, as well as the complete capture of surfaces is possible. Due to the digital light projector and the explicit projection of red, green or blue light, the true color of components can be analyzed and reproduced in 3D. Refl ections on surfaces can mostly be avoided by texture projection so the system dynamics can be greatly increased. Temperature Sensor Auto Joint Connection Global Shutter Sensor DLP Projector High quality WENZEL Lens Status LEDs Vibration-free Construction Beamer Integrated PC Camera Measuring volume Work piece Measuring field Technical Data Weight (g) 315 Dimensions (LxWxH) [mm] 120 x 78 x 74 Working Distance [mm] ~ 70 (+/-15) Measuring Field [mm] 40 x 30 Intensity [mm] +/- 15 Resolution Accuracy [µm] 754 x 480 (0,050 mm) Pixel +/- 8 nach DIN ISO Antastabweichung Reproducibility [µm] +/- 5 Scan Capacity [points/second] Live-Images per second Max. 30 Measuring Time Calibration Time ca. 1,0 sec < 1 min.

6 UNIQUE FUNCTIONALITY The combined Solution Innovation for success The Phoenix uses a unique combination of methods for evaluating the measurement data. Firstly, the phase-shift method using structured light projection and secondly, an image processing method is used for 3D measurement of features, for example circles. By simultaneous use of both of these methods the measurement of very thin-walled component features as in sheet metal and stamped parts, as well as the complete capture of surfaces is possible. Due to the digital light projector and the explicit projection of red, green or blue light, the true color of components can be analyzed and reproduced in 3D. Reflections on surfaces can mostly be avoided by texture projection so the system dynamics can be greatly increased. Temperature Sensor Auto Joint Connection Global Shutter Sensor DLP Projector High quality WENZEL Lens Status LEDs Vibration-free Construction Integrated PC Beamer Camera Measuring volume Work piece Measuring field WENZEL Group GmbH & Co. KG is one of the leading manufacturers of industrial metrology solutions. The wide range of WENZEL products includes solutions in the fields of coordinate measuring machines, gear metrology, computed tomography and optical high speed scanning systems. Founded in 1968 as a family business, WENZEL Group combines tradition with New Structured Light Projection and Image Processing Sensor Phoenix innovation, relies on values such as reliability, trust and respect for the environment. Subsidiaries as well as sales and service partners worldwide represent the company in more than 50 countries. The WENZEL Group employs more than 630 people worldwide. Authorized Representative: Willrich Precision Ph: sales@willrich.com Weight (g) 315 Dimensions (LxWxH) [mm] 120 x 78 x 74 Working Distance [mm] ~70 (+/-15) Measuring Field [mm] 40 x 30 Intensity [mm] +/- 15 Resolution 754 x 480 (0,050 mm) Pixel Accuracy [µm] +/- 8 nach DIN ISO Antastabweichung Reproducibility [µm] +/- 5 Scan Capacity [points/second] Live-Images per second Max. 30 Measuring Time ca. 1,0 sec Calibration Time < 1 min. WENZEL Präzision GmbH D Wiesthal Phone: Fax: info@wenzel-cmm.com Phoenix II_GB_01-20AC05 WENZEL Präzision GmbH Subject to technical modification and to changes in scope and design. Technical Data