Shrouded termination for XLPE-insulated cables 12 kv TB-A 12

Transcription

1 Kabeldon cable accessories for XLPE cables kv Shrouded termination for XLPE-insulated cables 12 kv TB-A 12 No special tools Easy measurement Easy installation Complete kits Active pressure Use Shrouded cable termination for connecting XLPE-insulated cables, 12 kv in switchgear, type ABB SafeLink. Standards Meets the requirements of: CENELEC, HD 629 Design TB-A is a shrouded termination made of rubber. Supplied in complete 3-core kits including cable terminations, two-piece boots, cable lugs with shear-off bolts, grease, cleaning cloth and installation instructions. Due to the smart installation method the upper part of the two-piece boot will stick to the bushing. When necessary for measuring, the lower part of the boot can easily be pulled down to expose the palm of the bushing. Accessories XLPE kv Note: For 3-core cables with common Cu-screen wires, a screen separation kit must be used. See page 53. Connector Designation Length Weight cross section mm² mm kg/kit Three 1-core or one 3-core kits TB-A TB-A TB-A

2 Kabeldon cable accessories for XLPE cables kv Prevent flash-over between phases Screen separation kit for SOC and KAP, PSSK Use For cables with common copper wire screen or Ericsson cables with aluminium wire screen. The screen of the 3-core cable is split up to each phase. Used to prevent flashover between the phases, for example in a switchgear bay. Used together with screened separable connector SOC or shrouded termination KAP. When a connector type SOC is installed, each core screen is connected to the outer conductive layer. L Accessories XLPE kv Standard Meets the requirements of EBR KJ 25:99. Design A copper stocking with a screen cross section of 25 mm² is fitted on each phase and connected to the screen wires of the cable. A heat shrink crutch seal and hoses are used as an outer sheath. Standard length is about 1200 mm plus length of accessory. It can also be cut for shorter installation. Designation Conductor cross section Length Weight 12 kv 24 kv L mm² mm kg/item PSSK PSSK PSSK 1 E* PSSK 2 E* * Special kits to be used with Ericsson's cables with Al-screen wires. 53

3 Kabeldon general accessories Other accessories IK 1105, 1106, 1107, 1108, 1109 Abrasive cloth. IK 1405, IK 1406 Lashing wire (tin-coated copper wire). IK 1401, IK 1407 Lashing wire (tin-coated copper wire). IK 1502 Lashing wire (galvanized steel wire). IK 2221 Silicone grease, 25 g. IK 2233 Grease, type AP paste, 10 g. Designation Length Diameter Coarseness Weight m mm kg/item IK IK IK IK IK IK IK IK IK IK IK IK

4 Kabeldon cable general accessories accessories Notes 1 kv Other accessories IA 1701 Earthing braid, sold by the metre, 10 mm². IA 1706 Copper net for e.g. SMXB, sold by the metre, approx. 10 mm². IA 1710 Earthing braid with lining, 22 mm². IK 2230 Washing cloth, 3 alcohol-soaked paper cloths 200 x 300 mm. MBR 250 Stainless marking tape, 100 units/kit. SKALUS Peeling string for XLPE-insulation. Designation Length Width Thickness Weight m mm mm IA kg/m IA kg/m IA kg/unit IK kg/unit MBR kg/kit SKALUS kg/unit 74 We reserve the right to alter the design and range of our products. Kabeldon, 2009 Edition 1

5 Kabeldon general accessories Tools R Torque wrench for screw connectors, screw cable lugs, overhead line clamps, etc. Supplied with 7 mm socket head, extension and 8 mm internal hexagon head. Torque range 6-50 Nm. Intercable No. RKS Cable shears for cutting cable Ø max 54 mm. 305 RKM 1055 Splitting tool for longitudinal splitting off XLPE-insulation with Ø mm RKM 670 Cable knife, 30 mm blade. RKM 672 Sheath removing knife with two handles for plastic sheated cable. Designation Description 730 R Torque wrench RKS Cable shears RKM 1055 Peeling tool RKM 1055 K Spare blade for RKM 1055 RKM 670 Cable knife RKM 672 Sheath removing knife 75

6 Kabeldon cable general accessories accessories Notes 1 kv Tools 153 Intercable No. AV 6220 Sheath removing tool for PE-sheathed cable Ø > 20 mm. 177 Intercable No. FBS Stripping tool for the vulcanized, outer conducting layer of XLPE-insulated cable Ø mm. The tool is supplied in a rigid case with a tube of silicone grease GB-M20 Cutting tool for cable sheath and XLPE-insulation: Diameter: Ø mm Cutting depth: 8 mm Model 1700 Series Peeling tool for strippable outer conductive layer on XLPE-insulated cable Ø mm. Designation AV 6220 FBS GB-M20 Model 1700 Series Description Sheath removing tool Stripping tool XLPE stripping tool Peeling tool 76 We reserve the right to alter the design and range of our products. Kabeldon, 2009 Edition 1