Report No. : EED32H Page 1 of 21 FCC TEST REPORT

Transcription

1 Report No. : EED32H Page 1 of 21 FCC TEST REPORT Product : IP Phone Trade mark : N/A Model/Type reference : XonTel S10P, XonTel S11P, XonTel S12P, XonTel S16P, XonTel S21P Serial Number : N/A Ratings : AC V, 50/60Hz Report Number : EED32H Date : Dec. 31, 2015 Regulations : See below Test Standards Results 47 CFR FCC Part 15 Subpart B: 2014 PASS Prepared for: SAHAB TECHNOLOGY Office 20, Qibia Tower, Fahad AI Salem St. Qibia, State of KUWAIT Prepared by: Centre Testing International Group Co., Ltd. Hongwei Industrial Zone, Bao an 70 District, Shenzhen, Guangdong, China TEL: FAX: Compiled by: Reviewed by: Approved by: Date: Dec. 31, 2015 Christy Chen Lab supervisor Check No.:

2 Report No. : EED32H Page 2 of 21 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION TEST SUMMARY MEASUREMENT UNCERTAINTY PRODUCT INFORMATION AND TEST SETUP PRODUCT INFORMATION TEST SETUP CONFIGURATION SUPPORT EQUIPMENT FACILITIES AND ACCREDITATIONS TEST FACILITY TEST EQUIPMENT LIST LABORATORY ACCREDITATIONS AND LISTINGS CONDUCTED EMISSION TEST LIMITS BLOCK DIAGRAM OF TEST SETUP PROCEDURE OF CONDUCTED EMISSION TEST GRAPHS AND DATA RADIATED EMISSION TEST LIMITS BLOCK DIAGRAM OF TEST SETUP PROCEDURE OF RADIATED EMISSION TEST GRAPHS AND DATA APPENDIX 1 PHOTOGRAPHS OF TEST SETUP...15 APPENDIX 2 PHOTOGRAPHS OF PRODUCT...16 (Note: N/A means not applicable)

3 Report No. : EED32H Page 3 of GENERAL INFORMATION Applicant: SAHAB TECHNOLOGY Office 20, Qibia Tower, Fahad AI Salem St. Qibia, State of KUWAIT Manufacturer: SAHAB TECHNOLOGY Office 20, Qibia Tower, Fahad AI Salem St. Qibia, State of KUWAIT Equipment Authorization: Verification Product: Trade mark: Model/Type reference: Serial Number: Report Number: IP Phone N/A XonTel S10P, XonTel S11P, XonTel S12P, XonTel S16P, XonTel S21P N/A EED32H Sample Received Date: Aug. 05, 2015 Sample tested Date: Aug. 05, 2015 to Oct. 15, 2015 The tested sample(s) and the sample information are provided by the client. All test data come from the report of No. EED32H TEST SUMMARY The Product has been tested according to the following specifications: Standard Test Item Test Method Test FCC Conducted Emission ANSI C63.4:2014 Yes FCC Radiated Emission ANSI C63.4:2014 Yes 3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the Product as specified in CISPR This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Test item Value (db) Conducted Emission 3.4 Radiated Emission 5.3

4 Report No. : EED32H Page 4 of PRODUCT INFORMATION AND TEST SETUP 4.1. PRODUCT INFORMATION Ratings: AC V, 50/60Hz Model difference: All models are identical except the appearance. The test model is XonTel S16P and the test results are applicable to the others TEST SETUP CONFIGURATION See test photographs attached in Appendix 1 for the actual connections between Product and support equipment SUPPORT EQUIPMENT No. Device Type Brand Model Series No. Data Cable Power Cord Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use. 5. FACILITIES AND ACCREDITATIONS 5.1. TEST FACILITY All test facilities used to collect the test data are located at Hongwei Industrial Zone, Bao an 70 District, Shenzhen, Guangdong, China. The site and apparatus are constructed in conformance with the requirements of ANSI C63.4, CISPR and other equivalent standards TEST EQUIPMENT LIST Instrumentation: The following list contains equipments used at CTI for testing. The calibrations of the measuring instruments, including any accessories that may effect such calibration, are checked frequently to assure their accuracy. Adjustments are made and correction factors applied in accordance with instructions contained in the manual for the measuring instrument. Equipment used during the tests: Shielding Room No. 1 - Conducted Emission Test Equipment Manufacturer Model Serial No. Due Date Receiver R&S ESCI /29/2016 LISN R&S ENV /29/2016

5 Report No. : EED32H Page 5 of 21 3M Semi-anechoic Chamber (1)- Radiated disturbance Test Equipment Manufacturer Model Serial No. Due Date 3M Chamber & Accessory Equipment ETS-LINDGREN FACT /12/2016 Spectrum Analyzer Agilent E4443A MY /12/2016 Receiver R&S ESCI /29/2016 TRILOG Broadband Antenna schwarzbeck VULB /22/2016 Multi device Controller ETS-LINGREN N/A 3M Semi-anechoic Chamber (2)- Radiated disturbance Test Equipment Manufacturer Model Serial No. Due Date 3M Chamber & Accessory Equipment TDK SAC /01/2016 Receiver R&S ESCI /29/2016 TRILOG Broadband Antenna schwarzbeck VULB /25/2016 Multi device Controller maturo NCD/070/ N/A Horn Antenna ETS-LINGREN /18/2018 Microwave Preamplifier Agilent 8449B 3008A /06/ LABORATORY ACCREDITATIONS AND LISTINGS The measuring equipment utilized to perform the tests documented in this report has been calibrated once a year or in accordance with the manufacturer's recommendations, and is traceable under the ISO/IEC/EN to international or national standards. Equipment has been calibrated by accredited calibration laboratories.

6 Report No. : EED32H Page 6 of CONDUCTED EMISSION TEST 6.1. LIMITS Frequency range (MHz) Limits for Class B digital devices Quasi-peak Limits db(μv) Average 0,15 to 0,50 66 to to 46 0,50 to to NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 to 0.50 MHz BLOCK DIAGRAM OF TEST SETUP 6.3. PROCEDURE OF CONDUCTED EMISSION TEST a. The Product was placed on a nonconductive table above the horizontal ground reference plane, and 0.4 m from the vertical ground reference plane, and connected to the main through Line Impedance Stability Network (L.I.S.N). b. The RBW of the receiver was set at 9 khz in 150 khz ~ 30MHz with Peak and AVG detector in Max Hold mode. Run the receiver s pre-scan to record the maximum disturbance generated from Product in all power lines in the full band. c. For each frequency whose maximum record was higher or close to limit, measure its QP and AVG values and record.

7 Report No. : EED32H Page 7 of GRAPHS AND DATA Product : IP Phone Model/Type reference : XonTel S16P Power : AC 120V/60Hz Temperature/Humidity : 24 /50% Mode : Normal Phase : L

8 Report No. : EED32H Page 8 of 21 Product : IP Phone Model/Type reference : XonTel S16P Power : AC 120V/60Hz Temperature/Humidity : 24 /50% Mode : Normal Phase : N

9 Report No. : EED32H Page 9 of RADIATED EMISSION TEST 7.1. LIMITS Limits for Class B digital devices Frequency (MHz) limits at 3m db(μv/m) Above NOTE: 1. The lower limit shall apply at the transition frequency. 2. The limits shown above are based on measuring equipment employing a CISPR quasi-peak detector function for frequencies below or equal to 1000MHz. 3. The limits shown above are based on measuring equipment employing an average detector function for frequencies above 1000MHz BLOCK DIAGRAM OF TEST SETUP 30MHz ~ 1GHz: Above 1GHz:

10 Report No. : EED32H Page 10 of PROCEDURE OF RADIATED EMISSION TEST 30MHz ~ 1GHz: a. The Product was placed on the non-conductive turntable 0.8 m above the ground at a chamber. b. Set the spectrum analyzer/receiver in Peak detector, Max Hold mode, and 120 khz RBW. Record the maximum field strength of all the pre-scan process in the full band when the antenna is varied between 1~4 m in both horizontal and vertical, and the turntable is rotated from 0 to 360 degrees. c. For each frequency whose maximum record was higher or close to limit, measure its QP value: vary the antenna s height and rotate the turntable from 0 to 360 degrees to find the height and degree where Product radiated the maximum emission, then set the test frequency analyzer/receiver to QP Detector and specified bandwidth with Maximum Hold Mode, and record the maximum value. Above 1GHz: a. The Product was placed on the non-conductive turntable 0.8 m above the ground at a chamber. b. Set the spectrum analyzer/receiver in Peak detector, Max Hold mode, and 1MHz RBW. Record the maximum field strength of all the pre-scan process in the full band when the antenna is varied in both horizontal and vertical, and the turntable is rotated from 0 to 360 degrees. c. For each frequency whose maximum record was higher or close to limit, measure its AV value: rotate the turntable from 0 to 360 degrees to find the degree where Product radiated the maximum emission, then set the test frequency analyzer/receiver to AV value and specified bandwidth with Maximum Hold Mode, and record the maximum value.

11 Report No. : EED32H Page 11 of GRAPHS AND DATA 30MHz ~ 1GHz: Product : IP Phone Model/Type reference : XonTel S16P Power : AC 120V/60Hz Temperature/Humidity : 24 /50% Mode : Normal Polarization : Horizontal

12 Report No. : EED32H Page 12 of 21 Product : IP Phone Model/Type reference : XonTel S16P Power : AC 120V/60Hz Temperature/Humidity : 24 /50% Mode : Normal Polarization : Vertical

13 Report No. : EED32H Page 13 of 21 Above 1GHz: Product : IP Phone Model/Type reference : XonTel S16P Power : AC 120V/60Hz Temperature/Humidity : 24 /50% Mode : Normal Polarization : Horizontal

14 Report No. : EED32H Page 14 of 21 Product : IP Phone Model/Type reference : XonTel S16P Power : AC 120V/60Hz Temperature/Humidity : 24 /50% Mode : Normal Polarization : Vertical

15 Report No. : EED32H Page 15 of 21 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP CONDUCTED EMISSION TEST SETUP RADIATED EMISSION TEST SETUP

16 Report No. : EED32H Page 16 of 21 APPENDIX 2 PHOTOGRAPHS OF PRODUCT View of Product-1 View of Product-2

17 Report No. : EED32H Page 17 of 21 View of Product-3 View of Product-4

18 Report No. : EED32H Page 18 of 21 View of Product-5 View of Product-6

19 Report No. : EED32H Page 19 of 21 View of Product-7 View of Product-8

20 Report No. : EED32H Page 20 of 21 View of Product-9 View of Product-10

21 Report No. : EED32H Page 21 of 21 View of Product-11 *** End of Report *** The test report is effective only with both signature and specialized stamp. The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CTI, this report can t be reproduced except in full.

22 FCC LABELLING AND INSTRUCTION MANUAL REQUIREMENTS Devices subject to FCC Part 15, Subpart B verification (not certification) must be labelled with the following statement. The label can be affixed at any space external to the product except the battery door or detachable parts. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In addition, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. If shielded cables or other specialized accessories are necessary for the unit to achieve compliance, a statement similar to the following should be added: Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.