OP8120 Modular Signal Conditioning Chassis User Guide.

Transcription

1 OP8120 Modular Signal Conditioning Chassis User Guide

3 SYMBOL DEFINITIONS The following table lists the symbols used in this document to denote certain conditions: Symbol Definition ATTENTION: Identifies information that requires special consideration TIP: Identifies advice or hints for the user, often in terms of performing a task REFERENCE _ INTERNAL: Identifies an additional source of information within the bookset. CAUTION Indicates a situation which, if not avoided, may result in equipment or work (data) on the system being damaged or lost, or may result in the inability to properly operate the process. Indicates a situation where users must observe precautions for handling electrostatic sensitive devices. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or! moderate injury. It may also be used to alert against unsafe practices.! WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in serious injury or death. OP8120 MSCC User Guide Opal-RT Technologies iii

4

5 CONTENTS OP8120 MODULAR SIGNAL CONDITIONING CHASSIS... 7 features...7 receiving and verification...7 standard hardware...7 OP8120 front interface...8 OP8120 rear interface...8 INSTALLATION AND OPERATION... 9 DB37 PIN ASSIGNMENTS OP8120 SPECIFICATIONS OP8121 CONDITIONING MODULE DESCRIPTION FEATURES...11 INSTALLATION AND OPERATION OP8121 SPECIFICATIONS OP8122 CONDITIONING MODULE DESCRIPTION...13 features...13 applications...13 INSTALLATION AND OPERATION OP8122 SPECIFICATIONS OP8124 CONDITIONING MODULE DESCRIPTION...15 features...15 applications...15 OP8124 SPECIFICATIONS LIMITED WARRANTY limited warranty...17 return policy...17 exclusions...17 warranty limitation and exclusion...18 disclaimer of unstated warranties...18 limitation of liability...18 MSCC User Guide Opal-RT Technologies 5

6 6 Opal-RT Technologies MSCC User Guide

7 OP8120 Modular signal conditioning chassis OP8120 MODULAR SIGNAL CONDITIONING CHASSIS OP8120 MSCC is a high power pre and post-conditioning chassis (amplifier) for our standard OP5330 and OP5340 analog I/O boards. It is designed to be used with simulators equipped with the OP5330 and OP5340 conditioning boards and to make high power conditioning and cabling easier to maintain. Each chassis can accommodate multiple modules for a maximum consumption of 500W. The chassis is designed according to module power consumption, and rather than a fixed number of channels. The chassis is nonetheless limited to a maximum of 32 channels per chassis at the lowest power rating per channel. features Quick connection using screw terminal and DB37 connectors Choice of current or voltage output boards Built-in power supply Maximum consumption: 500W Various contioning (amplifier) modules available receiving and verification When you receive your shipment, we strongly recommend that you verify the contents of the package(s). After carefully opening the package, remove the equipment and components. Make sure that all the items described below are actually in the box and are undamaged. standard hardware The OP8120 MSCC includes the following basic hardware: Item QTY Description Part Number OP8120 modular signal conditioning chassis 1 N/A DB37 cables 2 DB37M cables for connection to simulator Powerd cord 1 Standard power cord Documentation Test Report User Documentation CD N/A Opal-RT strongly recommends the use of anti-static wrist straps whenever handling any electronic device provided by Opal-RT. Damage resulting from electrostatic charges will not be covered by the manufacturers warranty. OP8120 MSCC User Guide Opal-RT Technologies 7

8 OP8120 Modular signal conditioning chassis OP8120 front interface The OP8120 interfaces is provided by the conditioning modules and include screw terminals for connecting to the unit under test, pushbuttons for channel activation and status LEDs. A OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS OP8122 4CH 1V@2A RMS B Figure 1: OP8120 front connector panels A. Power switch. B. Signal conditioning boards: -- OP8121: current output up to 5A RMS/1V RMS(see OP8121 Conditioning Module ) -- OP8122: current output up to 2A RMS/1V RMS (see OP8122 Conditioning Module ) -- OP8124: high voltage output up to 150V RMS/1 ma RMS (see OP8124 Conditioning Module ) OP8120 rear interface The rear interface contains DB37 connectors that represent the only user interaction zone on the back of the chassis. Power connections are factory wired. A B P1 P2 Figure 2: OP8120 rear connector panels A. 12 or ±24V power connection terminal (pre-wired) B. ±5V power connection terminal (pre-wired) C. 2 x DB37 connectors, to connect to simulator: -- P1 = channels P2 = channels C 8 Opal-RT Technologies OP8120 MSCC User Guide

9 INSTALLATION AND OPERATION OP8120 Modular signal conditioning chassis installation and operation The OP8120 chassis has rails that allow quick installation of the modules in the appropriate slot. Figure 3: Installation drawing 1. Simply position the module in alignment with the desired slot and push in firmly until connector is firmly pressed into the backplane connector. 2. When the module is in place, affix using the 4 screws provided. 3. When all modules are in place, plug the OP8120 power cable into a socket. 4. Put the power switch at the front of the OP8120 into on position (LED lit). The Conditioning chassis is now operational. For details on how to operate each module, please consult the sections pertaining to the module in question. OP8120 MSCC User Guide Opal-RT Technologies 9

10 OP8120 Modular signal conditioning chassis OP8120 Specifications DB37 PIN ASSIGNMENTS Simulator Signal DB37F (rear) Simulator Signal DB37F (rear) Vuser 18 VRTN 37 N/C 19 OP8120 SPECIFICATIONS Product name Power supply I/O connectors Modules per chassis Channels per module Number of channels Isolation: Vuser P1 OP8120 Modular Signal Conditioning Chassis Voltage and Frequency: universal inputs Module power up to 500W Vrtn ±5Vdc screw terminal (preconnected) (optional) 12Vdc or 24Vdc screw terminal (preconnected) Screw terminal on front conditioning modules DB37 on rear of chassis Maximum of 8, depending on module type 1 to 4 depending on power 1 to 32, depending on module Dimensions (HxWxD) 36.5 x 44 x 13cm (14.37 x x 5.12 ) Storage temperature Relative humidity Maximum altitude -55 to 85ºC (-67 to 185ºF) 10 to 90% non-condensing 2000 m (6562 ft.) Vuser P Vrtn 10 Opal-RT Technologies OP8120 MSCC User Guide

11 OP8121 CONDITIONING MODULE OP8121 Conditioning Module OP8121 INTERFACE DESCRIPTION The OP8121 MSCC module converts two (2) standard +/-16Vpk voltage inputs into two (2) current source up to 5A RMS under 1V RMS (voltage compliance). FEATURES LED fault indicators. Pushbutton activation/deactivation Front screw terminal connectors Easy installation (in chassis). The OP8121 module requires external power of and that is included with the OP8120 chassis. applications Current sensor simulation, Current source INSTALLATION AND OPERATION The OP8121 slides into the chassis using rails that allow quick installation of the modules in the appropriate slot. 1. Simply position the module in alignment with the desired slot and push in firmly until connector is firmly pressed into the backplane connector. 2. When the module is in place, affix using the 4 screws provided. 3. When all modules are in place, and the OP8120 is powered up, the modules are active. 4. Simply press the Activate/Deactivate button to activate the channels. OP8121 INTERFACE Status LEDs Screw terminal Channel activation pushbuttons Power LEDs Screw terminal Status LEDs Chassis Ground OP8121 2CH 1V@5A RMS 11 OP8120 MSCC User Guide Opal-RT Technologies

12 OP8121 Conditioning Module OP8121 Specifications STATUS LED TABLE Each channel has two LEDs, one red and one green. The following table explains what the channel status is, according to the LED conditions. POWER LED DESCRIPTION Each module has 2 power LEDs: Green LED Red LED Status On Off Activated Off On Deativated On On Fault When the left LED is on, it indicates that the 12Vdc fan is operating. When the right LED is on, it indicates that the ±5 Vdc power is functioning properly. ACTIVATE/DEACTIVATE PUSHBUTTON Each channel has an activation pushbutton. Press to turn outputs on or off, even if an input is present. OP8121 SPECIFICATIONS Product name Power supply (provided by OP8120 chassis) Maximum input voltage Operating frequency output: Number of channels Protection: OP8121 Signal Conditioning Module ±5Vdc@ 2.5Adc 12Vdc@ 275mA 16V pk 30 Hz to 1 KHz 1 to 32, depending on module (x2 outputs) Current and thermal protection Dimensions (HxWxD) 13 x 5 x 22.5 cm (5.12 x 1.97 x 8.86 ) Operating temperature Storage temperature Relative humidity Maximum altitude 10 to 40 ºC (50 to 104ºF) -55 to 85ºC (-67 to 185ºF) 10 to 90% non-condensing 2000 m (6562 ft.) OP8120 MSCC User Guide Opal-RT Technologies 12

13 OP8122 Conditioning Module OP8122 INTERFACE OP8122 CONDITIONING MODULE DESCRIPTION The OP8122 MSCC module converts four (4) standards +/-16Vpk voltage into four (4) current source up to 2A RMS under 1V RMS (voltage compliance). features LED fault indicators. Current and thermal protection Pushbutton activation/deactivation Front screw terminal connectors Easy installation (in chassis). The OP8122 module requires external power of and that is included with the OP8120 chassis applications Current sensor simulation, Current source INSTALLATION AND OPERATION The OP8122 slides into the chassis using rails that allow quick installation of the modules in the appropriate slot. 1. Simply position the module in alignment with the desired slot and push in firmly until connector is firmly pressed into the backplane connector. 2. When the module is in place, affix using the 4 screws provided. 3. When all modules are in place, and the OP8120 is powered up, the modules are active. 4. Simply press the Activate/Deactivate button to activate the channels. OP8122 INTERFACE Status LEDs Screw terminal Channel activation pushbuttons Power LEDs Screw terminal Status LEDs Chassis Ground OP8122 4CH 1V@2A RMS 13 Opal-RT Technologies OP8120 MSCC User Guide

14 OP8122 Conditioning Module OP8122 Specifications status led table Each channel has two LEDs, one red and one green. The following table explains what the channel status is, according to the LED conditions. Green LED Red LED Status On Off Activated Off On Deativated On On Fault power led description Each module has 2 power LEDs: When the left LED is on, it indicates that the 12Vdc fan is operating. When the right LED is on, it indicates that the ±5 Vdc power is functioning properly. activate/deactivate pushbutton Each channel has an activation pushbutton. Press to turn outputs on or off, even if an input is present. OP8122 SPECIFICATIONS Product name Power supply (provided by OP8120 chassis) Maximum input voltage Output frequency: Number of channels Protection: OP8122 Signal Conditioning Module ±5Vdc@ 2.5Adc 12Vdc@ 275mAdc 16V pk 30 Hz to 1 KHz 1 to 32, depending on module (x2 or x4 outputs) Current and thermal protection Dimensions (HxWxD) 13 x 5 x 22.5 cm (5.12 x 1.97 x 8.86 ) Operating temperature Storage temperature Relative humidity Maximum altitude 10 to 40 ºC (50 to 104ºF) -55 to 85ºC (-67 to 185ºF) 10 to 90% non-condensing 2000 m (6562 ft.) OP8120 MSCC User Guide Opal-RT Technologies 14

15 OP8124 CONDITIONING MODULE OP8124 Conditioning Module OP8124 INTERFACE DESCRIPTION The OP8124 MSCC module converts four (4) standard ±16Vpk voltage into four (4) high voltage outputs up to 150VRMS/1mA RMS. features LED fault indicators. Current and thermal protection Front screw terminal connectors Easy installation (in chassis). The OP8124 module requires external power of and that is included with the OP8120 chassis applications Excitation voltage (grid, elecrical machine, etc,) emulation High Voltage amplifier OP8124 INTERFACE Status LEDs Screw terminal Power LEDs Screw terminal Status LEDs Chassis Ground OP Opal-RT Technologies OP8120 MSCC User Guide

16 OP8124 Conditioning Module OP8124 Specifications status led table Each channel has two LEDs, one red and one green. The following table explains what the channel status is, according to the LED conditions. Green LED Red LED Status On Off Activated On On Fault power led description Each module has 2 power LEDs: When the left LED is on, it indicates that the internal ±15 Vdc power is functioning properly. When the right LED is on, it indicates that the ±24 Vdc power is functioning properly. OP8124 SPECIFICATIONS Product name Power supply (provided by OP8120 chassis) Maximum input voltage Output frequency: Number of channels Protection: OP8124 Signal Conditioning Module ±24Vdc@ 10Adc 12Vdc@ 275mA 16V pk 30 Hz to 1 KHz 1 to 32, depending on module Current and thermal protection Dimensions (HxWxD) 13 x 5 x 22.5 cm (5.12 x 1.97 x 8.86 ) Operating temperature Storage temperature Relative humidity Maximum altitude 10 to 40 ºC (50 to 104ºF) -55 to 85ºC (-67 to 185ºF) 10 to 90% non-condensing 2000 m (6562 ft.) OP8120 MSCC User Guide Opal-RT Technologies 16

17 Limited Warranty limited warranty LIMITED WARRANTY Opal-RT Technologies Inc. warrants to the original purchaser and/or ultimate customer ( Purchaser ) of Opal-RT products ( Product ) that if any part thereof proves to be defective in material or workmanship within one (1) year, such defective part will be repaired or replaced, free of charge, at Opal-RT Technologies discretion, if shipped prepaid to Opal-RT Technologies Inc. at 1751 Richardson, suite 2525, Montreal, Quebec, Canada, H3K 3G6, in a package equal to or in the original container. The Product will be returned freight prepaid and repaired or replaced if it is determined by Opal-RT Technologies Inc. that the part failed due to defective materials or workmanship. Otherwise, the fees will be charged to the client (see article warranty limitation and exclusion ). The repair or replacement of any such defective part shall be Opal-RT Technologies sole and exclusive responsibility and liability under this limited warranty. Purchaser must request an RMA number before shipping any Product for repair: 1. Access the Opal-RT website ( return-merchandise-authorization-rmarequest), click on support and select Return Merchandise (RMA). 2. Fill out the online form and submit. You will receive a notification with a thread-id that will be used for further exchange with support. 3. Opal-RT s Support department will evaluate the return and either issue an RMA number via using the same thread-id. -- If the Product is returned for repair more than 12 months after purchase, the Purchaser is responsible for the cost of repair. Opal-RT will assess the repair and prepare a quote. The RMA number will be sent with the quote. 4. Only when the Purchaser receives the RMA number, may they ship the Product, prepaid, to Opal-RT. return policy The following fees will apply when customers return products for credit: A full credit, less a 15% fee and less return fee will only be issued if the product is in perfect working condition and if the product is returned within 1 month following the shipping date. If repairs are required on the returned product, the cost of these repairs will be deducted from the credit to be issued. No credits will be issued beyond the one month period. exclusions If third party products are part of the Product, Opal-RT will honor the original manufacturer s warranty. This limited warranty does not cover consumable items, such as batteries, or items subject to wear or periodic replacement, including lamps, fuses or filter elements. OP8120 MSCC User Guide Opal-RT Technologies 17

18 Limited Warranty warranty limitation and exclusion Opal-RT Technologies will have no further obligation under this limited warranty. All warranty obligations of Opal-RT Technologies are void if the Product has been subject to abuse, misuse, negligence, or accident or if the Purchaser fails to perform any of the duties set forth in this limited warranty or if the Product has not been operated in accordance with instructions, or if the Product serial number has been removed or altered. disclaimer of unstated warranties the warranty printed above is the only warranty applicable to this purchase. All other warranties, express or implied, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose are hereby disclaimed. limitation of liability It is understood and agreed that Opal-RT Technologies liability, whether in contract, in tort, under any warranty, in negligence or otherwise shall not exceed the amount of the purchase price paid by the purchaser for the product and under no circumstances shall Opal-RT Technologies be liable for special, indirect, or consequential damages. The price stated for the product is a consideration limiting Opal-RT Technologies liability. No action, regardless of form, arising out of the transactions under this warranty may be brought by the purchaser more than one year after the cause of actions has occurred. 18 Opal-RT Technologies OP8120 MSCC User Guide

19

20 CONTACT Opal-RT Corporate Headquarters 1751 Richardson, Suite 2525 Montréal, Québec, Canada H3K 1G6 Tel.: Toll free: Note: While every effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions. Data may change, as well as legislation, and you are strongly advised to obtain copies of the most recently issued regulations, standards, and guidelines. This publication is not intended to form the basis of a contract. Technical Services UG OP1 10/2012 Opal-RT Technologies Inc.