LITTLE HADBURY CHANGING STATION

Transcription

1 LITTLE HADBURY CHANGING STATION ASSEMBLY INSTRUCTIONS. IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY. Tools Needed Helpline If you have any problems with this product or require any replacement fittings please contact Customer Services Tel: Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty. Should you need to return the unassembled product, please repack in the original packaging. IMPORTANT We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. WARNING: Do not leave the child unattended; Please note that all assembly fittings shall aways be correctly tightened and checked regularly; Be aware of the risk of open fire and other sources of strong heat,such as electric bar fires,gas fires etc.in the vicinity of the changing unit; Weight of the child the product is the intended up to a max.weight of 15 kg; Any additional or replacement parts shall only be obtained from the manufacturer or distributor; Do not to use the changing unit when any part is broken,torn or missing; Carefully check that you have all parts before beginning assembly. Keep fittings out of children's reach and keep children well away from the construction area. We recommend that the packaging is used to protect the surfaces during assembly. A minimum of two persons is required to assemble this product. Wall fixings are not included. We recommend the use of the wall attachment bracket/strap provided for safety reasons. The changing unit requires a changing mat measuring a maximum width of 510 mm / length of 740mm and thickness of 30mm. When mat fitted, there must be a maximum gap of 30mm between the mat sides and ends and the barrier sides andends. This item should not be dismantled for transportation or storage. PRODUCT INFORMATION Made from honeycomb board, partical board & MDF with a wood effect finish. Made in China. CARE INSTRUCTIONS For general cleaning, periodically dust with a soft cloth. Do not rub or scrub the surface when cleaning. Do not use furniture polish. Any spills should be removed immediately with a soft clean damp cloth and dried immediately. Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage. Do not put hot dishes directly on the surfaces of the item. Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping. Never drag pieces of furniture across the floor as this will cause damage to the joints. All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary. Please do not apply adhesive substrates for example, sticky tape to the product. Page 1 of 11

2 FITTINGS PARTS CHANGE STATION- STEP ONE 1. Attach panels 11, 14 & 12 to panel 13 with 6 x screws (F) and tighten with a screwdriver. Page 2 of 11

3 STEP TWO 1. Slide panel 15 into the assembled unit as shown in diagram. STEP THREE 1. Insert 3 x cambolts (D) into panel 16 and tighten with a screwdriver. 2. Glue and insert 5 x wooden dowels (B) into panels 11, 12 & 14 and attach panel 16 to panels 11,12 & Insert 3 x camlocks (E) into panels 11, 12 & 14 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver. STEP FOUR 1. Attach panel 19 to panels 20 & 21 with 6 x screws (F) and tighten with a screwdriver. 2. Glue and insert 6 x wooden dowels (B) into panels 22(x2) and attach panel 22(x2) to panels 20 & 21. Page 3 of 11

4 STEP FIVE 1. Glue and insert 6 x wooden dowels (B) into panels 22(x2) and attach panels 17 & 18 to panels 22(x2). 2. Attach panels 17 & 18 to panel 19 with 6 x screws (F) and tighten with a screwdriver. 3. Attach panel 14 to panel 19 with 2 x screws (F) and tighten with a screwdriver. STEP SIX 1. Slide panel 15 into the assembled drawer frame. STEP SEVEN 1. Insert 9 x camlbolts (D) into panel 23 and tighten with a screwdrive. 2. Glue and insert 9 x wooden dowels (B) into panels 17, 20, 21, 18 & 14 and attach panel 23 to panels 17, 20, 21, 18 & Insert 9 x camlocks (E) into panels 17, 20, 21, 18 & 14 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver. Page 4 of 11

5 STEP EIGHT 1. Insert 6 x camlbolts (D) into panels 1 & 2 and tighten with a screwdriver. STEP NINE 1. Glue and insert 4 x wooden dowel (A) into panels 3, 4 & 5 and attach panels 3, 4, & 5 to panel Insert 3 x camlocks (E) into panels 3, 4, & 5 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver. STEP TEN 1. Slide panel 10 into the assembled frame. Page 5 of 11

6 STEP ELEVEN 1. Glue and insert 4 x wooden dowels (A) into panels 3, 4 & 5 and attach panel 1 to panels 3, 4 & Insert 3 x camlocks (E) into panels 3, 4 & 5 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver. Note:One person needs to hold panel 1 while the other person is assembling this item STEP TWELVE 1. Slide panel 24 into the assembled unit as shown in diagram. STEP THIRTEEN 1. Attach 3 x bracket (L) to panel 7 with 6 x screws (M) and tighten with a screwdriver. 2. Attach panel 7 to panel 9 secure with 6 x screws (M) through bracket (L) and tighten with a screwdriver. 3. Insert 6 x camlbolts (D) into panel 9 and tighten with a screwdriver. Page 6 of 11

7 STEP FOURTEEN 1. Glue and insert 4 x wooden dowels (A) into panels 1 & 2 and attach panels 7 & 9 to panels 1 & Insert 6 x camlocks (E) into panels 1 & 2 and tighten with a screwdriver. Ensuring the arrow indicator is pointing towards the panel edge before tightening with a screwdriver. STEP FIFTEEN 1. Glue and insert 4 x wooden dowels (A) into panels 8 (x2). 2. Attach panels 8 (x2) to panel 7 with 2 x screws (H) and tighten with an Allen key (G). STEP SIXTEEN 1. Glue and insert 4 x wooden dowels (A) into panels 8 (x2). 2. Attach panel 6 to panels 8 (x2) with 2 x screws (H) and tighten with an Allen key (G). Page 7 of 11

8 STEP SEVENTEEN 1. Attach 3 x metal plate(n) to panels 6 & 9 with 6 x screws (M) and tighten with a screwdriver. STEP EIGHTEEN 1. Insert two drawers into the assembled unit as shown in diagram. Note: If you want to disassembled the unit, please follow the steps as the right brief to push the drawer out. STEP NINETEEN 1. Insert 8 x plastic fasteners (J) into the back panel grooves and tighten with screws provided. 2. Use 4 x stickers (K) to cover the holes on panels 6 & 7. Page 8 of 11

9 STEP TWENTY 1. Using screw and washer secure the 2 x nylon straps (I) to the back of panel Move the unit into desired position. 3. Secure the other end of the strap to the wall with an appropriate screw and wall plug for your wall type (not provided).to hide the strap behind the unit,drill the hole lower than the top of unit. Warning: Always ensure intended wall area to be drilled is free from hidden electrical wires,water and gas pipes. NB:Wall fixings are not included-please source suitable fixing for your wall type. If in doubt please consult a qualified trades person. CONVERTING THE CHANGING TO A CHEST STEP ONE 1. Untighten screw and remove 2 x the nylon straps (I) from panel 7 as shown in diagram. Page 9 of 11

10 STEP TWO 1. Follow the steps as the right brief to remove the top drawer. Note: Please follow the steps as the right brief to push the drawer out. STEP THREE 1. Untighten 6 x screws (M) and remove out the 3 x metal plate (N) from panels 6 & 9 as shown in diagram. STEP FOUR 1. Untighten 12 x screws (M) and remove out the 3 x bracket (L) from panels 7 & 9 as shown in diagram. Page 10 of 11

11 STEP FIVE 1. Remove the frame as shown in diagram. STEP SIX 1. Insert the drawer into the assembled unit as shown in diagram. Note: If you want to disassembled the unit, please follow the steps as the right brief to push the drawer out. STEP SEVEN 1. Using screw and washer secure the 2 x nylon straps (I) to the back of panel Move the unit into desired position. 3. Secure the other end of the strap to the wall with an appropriate screw and wall plug for your wall type (not provided).to hide the strap behind the unit,drill the hole lower than the top of unit. Warning: Always ensure intended wall area to be drilled is free from hidden electrical wires,water and gas pipes. NB:Wall fixings are not included-please source suitable fixing for your wall type. If in doubt please consult a qualified trades person. Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT Page 11 of 11