IP Sensor IPS2222 Manual

Transcription

1 IP Sensor IPS2222 Manual Output LED indicators ss 2 Relay Power input outputs 12VDC adapter LED Indicators Green : Power Yellow:Link 1 wire 2 Dry 2 Analog temperature contact inputs & humidity inputs sensor input Page 1

2 Benefits and Features. IPS2222 is a device with build on Ethernet web server with 2 dry contact inputs, 2 analog inputs, 2 relay outputs, 1-Wire input for up to 2 temperature & humidity sensors. Device can be controlled and monitored over any IP network and Internet by web browser or any specialized monitoring software by SNMP v1 and v2 protocol. Benefits Easy and fast configuration full configuration can be performed through the Web using a web browser Control and configuration over TCP/IP and SNMP IP security access to the IPS2222 is protected by name and password 2 dry contact inputs 2 analog inputs 2 relays with NO contacts 1-Wire input for 2 Temperature & humidity sensors Alarm alert SNMP trap and XML (over HTTP) SNTP synchronization protocol Firmware update over IP Page 2

3 Technical Features Power supply 12VDC / 0.5 A (adapter) Jack Ø5.5 x 2.0 / 10mm Network standards: IEEE 802.3, 10 Mbit/s Network connection: RJ 45 10BASE-T / 10 Mbps Network protocol TCP/IP and HTTP Operating conditions: - 10 to + 60 C 2 dry contact inputs (volt free) 2 analog inputs - 0 to 60 V DC 2 Relay outputs 3A /24V DC/30V DC 1 sensor input RJ11 for connecting 1-Wire temperature & humidity sensors Aluminium enclosure Dimensions 112 x 40 x 50 [mm] / wall mount Device Connection Connect the IPS2222 to the 10 Mbit or 10/100 Mbit network. Use a classic TP patch cable for connection to switch or router or to PC. If the Ethernet connection is OK, the POWER and LINK indicator should light up and then LINK indicator blink according to network data transfer. Page 3

4 Restoring defaults factory configuration Press and hold the Reset button located on the back of the box, connect power, and hold the button pressed for 10 seconds or more. Reset Button Default network parameters configuration: IP address: Network mask: Default gateway: IP configuration via DHCP: Disabled User name: admin Password: admin Page 4

5 Installation Guidelines IPS2222 controller must be installed by qualified personnel. Controller must not be installed directly outdoors. IPS2222 must not be used for medical, life saving purposes, or for any purpose where its failure could cause serious injury or the loss of life. This unit must not be used in any way where it's function or failure could cause significant loss or property damage. The first step is to establish communication between computer and IPS2222 controller. This can be done by assigning a temporary IP address to the computer. For computers with Windows OS assigning of IP address is made in Local area connection properties or Wireless Network Connection Properties. Page 5

6 IP Address of the computer should be at the same network. Into the browser you should type If network settings are correct the login page will appear. Page 6

7 Web Pages Login Page - access to the IPS2222 is protected by name and password Status Page - Monitoring parameters Action when alarm is activated Alarm threshold Page 7

8 Network Settings configuration of network parameters MAC address hardware address of the device. After a change, device will be reboot automatically and redirect to the index page. IP address software address of the device. After a change, device will be reboot automatically and you must search it on the new IP address. Enable DHCP - allows device automatically obtain a valid IP address Gateway default gateway Subnet mask local network mask Primary DNS needs to be set properly for correct operation. Domain Name Service associates host names with IP addresses. Without a correctly configured DNS server, the following functions will not work: - Time synchronization (SNTP), used in s and SNMP traps - E- mailing (SMTP) HTTP Port The TCP port used for HTTP communications with IPS2222. Default settings for this port is 80. Value of HTTP port can be changed from 80 to Page 8

9 When an HTTP request is without specific port specified then is exactly the same as For example if default port is changed to port 1560 then HTTP request must be System Settings Device name is used to identify device on the network NTP server host name of the NTP server to synchronize the time with. Time zone offset of your timezone with respect to that of the NTP Server. If the time is not set the device attempts to synchronize the time approximately once per hour until successful. Current Date - it is necessary to send s. Current Time it is necessary to send s. The time updates on every minute. To refresh the time it is necessary to click the System page. Temperature units - Specifies the unit of temperature (C Celsius / centigrade, F Fahrenheit) Page 9

10 Account Settings - One user account with username and password can be configured for HTTP access. Sensors Settings Name name of the sensor up to 15 chars ( e.g. like Indoor ) ID unique number for each sensor Measured value the value that sensor is reading. P a g e 10

11 Lower range - value below this range are considered to be incorrect and alarm event occurs Upper range - value above this range are considered to be incorrect and alarm event occurs Hysteresis hysteresis is used to avoid multiple alarms when the measured quantity fluctuate. Trap device send a SNMP Trap when alarm event occurs and this option is checked - device send an when alrm event occurs and this option is checked After connecting sensors or changing RJ11 connections, detect sensors again. SNMP Settings P a g e 11

12 The Simple Network Management Protocol - SNMP, is a commonly used service that provides network management and monitoring capabilities. SNMP offers the capability to poll network device and monitor data. SNMP is also capable changing the configurations on the host, allowing the remote management of the network device. The protocol uses a community string for authentication from the SNMP client to the SNMP agent on the managed device. The SNMP Settings page allows you to configure the settings for communication with the device using the SNMP protocol v2.0. SNMP settings SNMP - Enable / Disable communication by SNMP SNMP Port communication port for SNMP protocol. Default port is 161. Write Community - The community is authorized to write values to variables over SNMP. The default write community string is private. Read Community - The community is authorized to read values to variables over SNMP. The default read community string is public. Trap settings Trap - Enable / Disable sending trap messages Trap IP address IP address of the trap destination Trap community default trap community is public Trap interval time interval for trap messages in seconds. Min interval = 5 sec. Traps are sent in following conditions: - dry contact inputs change their status - measured voltages on analog inputs goes outside the range - measured temperature or humidity goes outside the range For management and control by SNMP is necessary to use MIB file. MIB file you can download from our website P a g e 12

13 XML Interface Any application can easily read current values from status.xml tags. File is located at or P a g e 13

14 Settings Mail server custom or dedicated ip-sens.com. If you not have a SSL mail server on your network then we provide service for free use of the dedicated mail server from ip-sens.com. The service from our server is free and not guaranteed! Mail Server Address Host name or IP address of the SMTP server Authentication if necessary use name and password for Mail server Port This controls the port for which outgoing mail connections will be accepted. SMTP uses TCP port 25 or 587. SSL is not supported. P a g e 14

15 Inputs / Outputs Settings User defined names Name - In this field you can enter the name of the corresponding parameter as it should be spelled in the Status page Digital inputs used for direct connection of volt-free contacts. One side of the contact is connected to Input1 or Input2 and the other side is connected to terminal in the middle GND. When alarm state is Active if Close then default value is Open and the alarm is activated when active value become Close. When alarm state is Active if Open then default value is Closed and alarm value is activated when active value become Open. You can choose which type of alarm to be activated Trap or or both alarms. All digital inputs are not galvanic isolated. Analog inputs - used for measuring DC voltages. Before using alarm alerts need to set values in the fields Lower Range and Upper Range. Relay output settings can select whether the relay to be activated manually by click button ON/OFF or automatic by any of the following parameters or by all sensors: P a g e 15

16 - Dry contact input 1 - Dry contact input 2 - Analog input 1 - Analog input 2 - Sensor 1 Temperature - Sensor 1 Humidity - Sensor 2 Temperature - Sensor 2 Humidity - All Sensors Only one parameter can be assigned for relay activation, at the same time. For loads greater than 3A/30V DC an external relay should be used. Firmware update In this page you can update IPS2222 with the new firmware. Please keep in mind not to power off the device during the update! It can damage the device! P a g e 16

17 Application Examples - Remote monitoring application P a g e 17

18 P a g e 18

19 - Control of 220V AC / 20 A motor using external relay - Control of DC powered Electric Lock P a g e 19

20 Mechanical dimmensions Bottom view P a g e 20