acacia MINI BAR hardware tools required components 1 - top crossbar Missing hardware? Please call for replacements.

Transcription

1 hardware Missing hardware? Please call for replacements wood dowels 8 - cam screws 8 - cams 24 - small screws 16 - large screws 16 - small 6 - large 22 - flat washers 22 - spring washers Thank you for purchasing the Acacia Mini Bar. This page lists all the contents included in the box. Please take the time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. Note: 2 people are required to safely assemble this product. 8 - pull 4 - hinges tools required phillips head screwdriver allen wrench (included) 12 - shelf supports 2 - anchors (We recommend the use of hand tools instead of power tools) components 1 - top 1 - right side 1 - left side 1 - partition glass shelves 1 - large door 1 - small door 1 - top 1-1- back 4 - legs 2 - drawer s 4 - drawer sides (2 left, 2 right) 2 - drawer backs 2 - drawer s 4 - pulls Page 1 of 7

2 NOTE: Do not over tighten the small bolt spring washer flat washer leg NOTE: Make sure arrows on each cam points toward nearest edge with holes 1 Attach 4 legs to with 4 small, 4 spring washers and 4 flat washers as shown. Secure, but do not over tighten, with an allen wrench. 2 Insert 2 cams into as shown. Make sure arrows on each cam points toward nearest edge with holes. NOTE: Do not over tighten the cam screws right side partition top partition NOTE: Make sure plastic piece on each face up and bend towards the back of assembly as shown right side Insert 4 wood dowels, 2 cams, and 1 cam screw into partition and right side as shown. Secure, but do not over tighten, cam screws with a 3 4 phillips head screwdriver. Fit dowels of top/ s into corresponding holes of partition and right side as shown. Using a screwdriver, turn each cam clockwise until it securely engages each cam screw. Page 2 of 7

3 left side assembly flat washer spring washer large bolt 5 Insert 4 wood dowels and 2 cams into left side as shown. 6 Fit dowels of partition and side s into corresponding holes of assembly as shown. Secure with 6 large, 6 spring washers and 6 flat washers as shown, using an allen wrench. back top With the assistance of another adult, carefully position unit upright. Slide back into 7 grooves of assembled unit as shown. 8 Insert 6 cam screws into top as shown. Page 3 of 7

4 top shelf support 9 Fit dowels of assembled unit into corresponding holes of top as shown. Secure all cams. 10 Insert 12 shelf supports at desired shelf heights. A NOTE: Do not over tighten the screws anchor large door B pull small door Insert tabs of anchor into corresponding corner of assembled unit of assembled unit as shown. Secure, but do not over tighten screw with a screwdriver A. Attach 2 hinges to small/large door s with 2 small screws per hinge as shown. Secure, but do not over tighten, screws with a screwdriver. B. Attach pull to each door with 2 pull, using a screwdriver. Page 4 of 7

5 glass shelf Refer to Hinge Adjustment diagram for adjusting the alignment of the door hinges. door 13 Place 3 glass shelves into assembled unit as shown. Make sure shelves are securely supported by shelf supports. 14 Attach hinges of each door to side s as shown. Secure each hinge with 4 small screws and 1 hinge bolt, using a screwdriver. drawer drawer left side drawer Fit dowel of inner drawer into corresponding holes of drawer left side, and secure with 2 large 15 screws. 16 Slide drawer into groove of drawer assembly as shown. Page 5 of 7

6 drawer back drawer right side 17 Fit dowel of drawer back into corresponding holes of drawer assembly, and secure with 2 large screws. 18 Fit dowels of drawer assembly into corresponding holes of drawer right side and secure with 4 large screws. pull 19 Attach pull to drawer with 2 pull, using a screwdriver. Repeat steps for remaining drawer assembly. Insert 2 drawer assemblies into assembled unit as shown. Push drawer back until you hear a click. Assembly is now complete. cleaning and care Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit is finished with a protective clear lacquer. It is recommended to use coasters to protect surface from heat and water. Clean glass shelves with glass cleaner. Page 6 of 7 20

7 hinge adjustment If the doors do not appear square or aligned,loosen or tighten the appropriate screws on each case hinge as illustrated A A C B B C Side to side adjustment: Loosen screw A, adjust gap with screw B and re-tighten screw A Depth adjustment: Loosen screw A, push hinge arm forwards or backwards, re-tighten screw A and secure screw B with a 1/4 turn clockwise Height adjustment: Loosen screw C, adjust door height and re-tighten screw C Page 7 of 7