ROOM COMMAND MODULE with NTC sensor TM P/N Built-in NTC temperature sensor

Transcription

1 with sensor TM Push button Mode Selector with indication: - Comfort/ on - Stand-by/ blinking - Night/ off - Set point range: C mode led COM the cover. (See sketch 1). output and secure with at least two screws. (See sketch 2) SKETCH 1 SKETCH 2 P/N

2 with sensor - Set point range: C ± 3 K TM-9190-x000 1=Separable connectors 0=Plug-in connector fixed onto the base -000x 0=Dial range C 5=Dial range ± 3 K R.S.P - Set point range: C ± 3 K - Override of fan velocity control: - automatic - off - 1 st,2 nd,3 rd,fan speed velocity _ TM-9190-x000 1=Separable connectors 0=Plug-in connector fixed onto the base -000x 2=Dial range C 7=Dial range ± 3 K R.S.P Fan Control inserting a pointed tool (a special tool, Ordering Code TM , is available from Johnson Controls) into the small hole at the center top of the cover. (See sketch 1). from the cover. continue to pull the cover away from the base until the cover is in free. output and secure with at least two screws. Sketch 1 P/N

3 with sensor TM Set point range: ± 3 K the cover. (See sketch 1). output and secure with at least two screws. SKETCH 1 P/N Rev. A

4 INSTALLATION INSTRUCTIONS MOUNTING INSTALLING TM x ROOM COMMAND MODULE WITH LCD DISPLAY the cover (See Figure 1). output and secure with at least two screws (See Figure 2). Figue 1: TM SPECIFICATIONS - Push button Mode Selector with indication: - Comfort / on - Stand-by / blinking - Night / off - Set Point Change Enable / Disable selectable via a Jumper ORDERING CODE TM x 0 = Without LED Indication and Push Bottom 1 = With LED Indication and Push Bottom Figue 2: Mounting Dimensions of Rear of Command Module cover.. JUMPER SETTING - Jumper Setting (See Figure 3) : Remote Set Point change Disable Enable NOTE: Change Jumper JP3 position of TC-9102 Controller as follows: Figue 3: Jumper location Powered JP2 8V DC COMMON JP Figue 4: Wiring Connections P/N

5 INSTALLATION INSTRUCTIONS MOUNTING INSTALLING TM x ROOM COMMAND MODULE WITH LCD DISPLAY the cover (See Figure 1). output and secure with at least two screws (See Figure 2). Figue 1: TM SPECIFICATIONS - Push button Mode Selector with indication: - Comfort / on - Stand-by / blinking - Night / off - Set Point Change Enable / Disable selectable via a Jumper ORDERING CODE TM x 0 = Without LED Indication and Push Bottom 1 = With LED Indication and Push Bottom Figue 2: Mounting Dimensions of Rear of Command Module cover.. JUMPER SETTING - Jumper Setting (See Figure 3) : Remote Set Point change Disable Enable NOTE: Change Jumper JP3 position of TC-9102 Controller as follows: Figue 3: Jumper location Powered JP2 8V DC COMMON JP Figue 4: Wiring Connections P/N

6 with sensor TM-9160-S Set point range: C ± 3 K P/N

7 with Fan Speed Override - Push button Mode Selector with indication: - Comfort/ on - Stand-by/ blinking - Night/ off - Set point range: F ± 5 F - Override of fan velocity control: - automatic - off - 1st, 2nd, 3rd fan speed velocities TM-9160-X X 0 = C / K 5 = F 2 = Dial Range F 7 = Dial Range ±5 F Mode Fan Control Override - Push button Mode Selector with indication: - Comfort/ on - Stand-by/ blinking - Night/ off - Set point range: F ± 5 K - Override of fan velocity control: - automatic - off - 1st, 2nd, 3rd fan speed velocities TM-9170-X X 0 = C / K 5 = F 2 = Dial range F 7 = Dial range ± 5 F Mode Fan Control Override P/N

8 with sensor TM led mode - Push button Mode Selector with indication: - Comfort/ on - Stand-by/ blinking - Night/ off - Set point range: F ± 5 F TM-9160-X000 0 = C / K 5 = F -000X 0 = Dial range F 5 = Dial range ± 5 F led mode P/N Rev.A

9 INSTALLATION INSTRUCTIONS MOUNTING INSTALLING TM xx0 ROOM COMMAND MODULE WITH LCD DISPLAY the cover (See Figure 1). outlet and secure with at least two screws (See Figure 2). Figure 1: TM SPECIFICATIONS - Push button Mode Selector with indication: - Comfort / on - Stand-by / blinking - Night / off - Service Module Socket (depending on model) ORDERING CODE TM xx0 1 = With View Mode and Clock Setting only 2 = With View Mode and Programming Mode TM xx0 0 = Without Service Module socket 1 = With Service Module socket Figure 2: Mounting Dimensions of Disable Rear of Command Module cover Enable JUMPER SETTING /1: Clock Setting /2: Fan Speed Enable or Disable /3: Time Schedule Figure 3: Jumper location NOTE: Change Jumper JP3 position of TC-91xx as follows : TC-9100 TC-91x2 TB TB JP Powered JP2 JP V DC COMMON COMMON Figure 4: Wiring P/N Connections