8901 Access Control Panel Installation Guide

Size: px

Start display at page:

Download "8901 Access Control Panel Installation Guide"

Madlyn Davidson
7 years ago
Views:

1 1. Introduction 2. Technical Specification 3. System Deployment 4. Panel Layout 5. Detailed Pin Assignment 6. Panel Configuration 7. Sample Connection Circuits System Reader Electrical Lock Door Alarm Door Ajar Door Sensor Release Button Panel Tamper Version C Design. Innovations Page 1 of 17

2 1. Introduction This document provides detailed description about the features, functions and setup of ACX 8901 Control Panel. A. Strength Native TCP/IP on board, 10/100Mbps communication speed Flexibility structure cabling, cat 5 cable, direct to hub or panel to panel daisy chain wiring. Multi-threading program, transactions upload to database server less than 2 sec under 50 panels. User defined 128 bits key for the data exchange between ACX 8901&8902 door access panel to ACX COM Server, prevent the real data to be snooped and simulated by other network point. User defined 128 bits key, scramble RS485 data exchange between ACX 8901&8902 door access panel and ACX reader, prevent reader data to be snooped and copied. Work with ACX 2081 I/O module, save the wiring cost and increase the data security (patented design) Support 7 x card number format, each card number format has 3 x facility code checking Work with ACX LCD reader, display interactive message Work with ACX emergency door open device Supervised Monitor of the Door Sensor Input, Prevent trouble close and open B. Features 32 bits microprocessor, 50MHz External device short circuit protection Thumbed protection Recoverable fuse protection. Status LED represents operating status Auto recover for the TCP/IP failure Battery on board for memory retention, 3 years Firmware can be on-line upgraded Real time clock, less than 1 sec deviation daily. Twin card operation (100 couples) Anti-passback Two door interlock Version C Design. Innovations Page 2 of 17

3 C. Panel Appearance Version C Design. Innovations Page 3 of 17

4 2. Technical Specification Specification 8901 Panel Inputs Panel Outputs Memory PCB Dimension Expansion Holidays Timezone - 1 x IN and 1 x OUT Wigand reader or; - 1 x IN and 1 x OUT ACX scramble RS485 reader - 1 x door sensor input - 1 x request to exit input - 1 x auxiliary input - 1 x controller box tamper input - 1 x ACX high security key open door device - Power input monitoring : A.C. / D.C. / Backup Battary - Work with ACX high security door emergency open device, couple with random key switch & reset panel. - 1 x E-Lock relay dry contact output, max. 10A current rating - 1 x Alarm relay dry contact output, max. 3A current rating - 1 x Door ajar TTL signal output, 5VDC output, 20mA VDC battery charging - 38,000 cardholders, each card holder has 24 bytes content - 45,000 swipe card records events 120mm x 120mm x 12mm 1 x RS485 serial port for expansion, software and hardware interface to other system 100 Holiday dates - 80 x access control time zone - 1 x password time zone - 1 x electric Lock time zone - 1 x alarm time zone - 1 x door ajar time zone - 1 x request to exit time zone - 1 x twin card operation time zone All timezone can be assigned from Monday to Sunday and Holiday, 4 intervals per day, time zone can be selected globally or individually Password Communication - User password, timezone control - Global password, key in the password through keypad reader open door - Duress password, open door but trigger alarm output - Panel to hub, CAT 5 cable (max. 100 meters) - Panel to panel, daisy chain by CAT 5 cable (max. 100 meters) Version C Design. Innovations Page 4 of 17

5 No. of Panels Depends on IP address available Backup Battery Operating Voltage Operating Temperature Operating humidity Wiegand Reader - 12VDC, 7AH backup battery, - provide at least 4 hours operation, excludes electric lock power consumption - 220V, 5A input in AC. - 12VDC, 3A output 0 to 65 C 0-95% relative humidity non-condensing - Communication: Wiegand - Green / Red LED control - Buzzer control - Reader in 6 wires connection - Max. cable length : 150m ACX Reader - Communication : RS485 - High Security scramble data encryption - 7 x LED color control - Buzzer Control - Interactive message display for ACX LCD reader - Reader in 4 wires connection - Max. cable length : 1,200m Version C Design. Innovations Page 5 of 17

6 3. System Deployment There are three ways to connect panels. All of the panels communicate in TCP/IP protocol with each other. CAT5 cable is used to connect the panel to the (LAN) Local Area Network or connect the panels in Daisy Chain. RS 485 protocol is no longer used for inter-panel communications so that the cost is reduced and the speed is increased. Multi-threading is also used to speed up concurrent operations. Pier to Pier Daisy Chain Pier to Pier + Daisy Chain Pier to Pier DATABASE and SOFTWARE Local Area Network TCP/IP TCP/IP TCP/IP.... Daisy Chain DATABASE and SOFTWARE Local Area Network TCP/IP TCP/IP.... Version C Design. Innovations Page 6 of 17

7 Pier to Pier + Daisy Chain DATABASE and SOFTWARE Local Area Network TCP/IP TCP/IP.... TCP/IP.... Version C Design. Innovations Page 7 of 17

8 4. Panel Layout ACX 8901 Single Door TCP/IP Panel 120mm C2 C3 C4 C5 C2 : NO / NC / COM / PWR / GND (1) C3 : Door Ajar / NO / NC / COM (1) C4 : Door Sensor / GND / RTE / GND (1) - AUX IN - Tamper 12VDC, 3ADC RJ45 RJ45 120mm C1 2 x Wiegand or ACX Scramble RS485 reader Power / Ground / D0 / D1 / ACK / Buzzer / RS485 T+ / RS485 T- RS485 Port (for future use) For Emergency Door open Device AC / DC / Backup battery monitoring C6 C7 C8 C10 C9 Start from the left is PIN 1 when face the terminal Version C Design. Innovations Page 8 of 17

9 5. Detailed Pin Assignment 8901 Single Door TCP/IP Controller Connector Summary PIN Description C1 C2 C3 C4 C5 C6 C7 C8 Power Input E-Lock Power (12V, 1.5A) E-Lock Output (Dry Contact) Door Alarm Output (Dry Contact) 1 12VDC, 3ADC 1 Ground 2 Power 3 COM 4 NC 5 NO 1 COM 2 NC 3 NO Door Ajar Output 4 Normal is 0VDC, Door Ajar 5VDC, 200mA output Door Sensor Release Button AUX INPUT Panel Tamper RS485 Port (Custom use) For Emergency Door Open Device Power Status 1 Door Sensor 3 Release button 4 Ground 1 IN#1 3 Tamper 4 Ground 1 RS485 (T+) 2 RS485 (T-) 3 RS485 (T+) 4 RS485 (T-) 1 Power Out (12VDC, 100mA) 3 Signal + 4 Signal - 1 DC Power 2 Backup Battery Version C Design. Innovations Page 9 of 17

10 3 A.C. Power 4 Ground 1 Reader Power (200mA) 3 Data 0 4 Data 1 C9 OUT Reader 5 Green LED (ACK) 6 Buzzer 7 RS485 (T+) ACX RS485 reader only 8 RS485 (T-) ACX RS485 reader only 1 Reader Power (200mA) 3 Data 0 4 Data 1 C10 IN Reader 5 Green LED (ACK) 6 Buzzer 7 RS485 (T+) ACX RS485 reader only 8 RS485 (T-) ACX RS485 reader only 1 RJ45 2 Ports TCP/IP Switch Connect to TCP/IP swtich or next Panel 2 Version C Design. Innovations Page 10 of 17

$6. Panel Configuration Panel Address 1. Go to the IP Config folder under the Installation folder (Normally C:\Program Files (x86)\acx\x.90 Access Control System\Set IP Config).$

11 6. Panel Configuration Panel Address 1. Go to the IP Config folder under the Installation folder (Normally C:\Program Files (x86)\acx\x.90 Access Control System\Set IP Config). Open the IP Configuration utility program. 2. Click Scan button. 3. Select the device and modify the IP Address or other parameters. Input the PWD and Click Set button to download configuration to the board. Remark: The Default Key is Version C Design. Innovations Page 11 of 17

12 7. Sample Connection Circuits A. System Daisy Chain Hub TCP/IP 8901/8902 Server L A N TCP/IP TCP/IP 8901/ /8902 Version C Design. Innovations Page 12 of 17

13 B. Reader Wire Color: Reader: C9, C10 1. Red Reader Power 2. Black Ground 3. Green Data 0 4. White Data 1 5. Orange Green LED (ACK) 6. Yellow Buzzer 7. Purple RS485 (T+) 8. Grey RS485 (T-) Wiegand Reader Wiegand Reader ACX Scramble RS485 Reader (Improved Security) Scramble RS 485 Reader Version C Design. Innovations Page 13 of 17

14 E-Lock 8901 Access Control Panel Installation Guide C. Electrical Lock Pin Assignment: E-Lock: C2 1 Ground 2 Power 3 COM 4 NC 5 NO + E-Lock - Normally Closed with Power on Panel E-Lock + - Normally Open with Power on Panel External Power Normally Closed with External Power E-Lock + - External Ground External Power Normally Open with External Power + - External Ground Version C Design. Innovations Page 14 of 17

15 D. Door Alarm (Dry Contact) Pin Assignment: Alarm: C3 1 COM 2 NC 3 NO 4 Normal is 0VDC, Door Ajar 5VDC, 20mA output External Power Normally Open with External Power Alarm Device + - External Ground External Power Normally Closed with External Power Alarm Device + - External Ground E. Door Ajar Output Pin Assignment: Door Ajar: C3 1 COM 2 NC 3 NO 4 Normal is 0VDC, Door Ajar 5VDC, 20mA output LED Connect to LED indication Panel Ground Version C Design. Innovations Page 15 of 17

16 F. Door Sensor and Release Button Input Pin Assignment: Door Sensor and Release Button: C4 1 Door Sensor 3 Release button 4 Ground Door Sensor Connect the Sensor Input Release Button G. Panel Tamper Panel Tamper: C5 Pin Assignment: 1 Door Sensor 3 Release button 4 Ground Normal is Close Connect the Sensor Input Version C Design. Innovations Page 16 of 17

17 H. Emergency Door Open Device Pin Assignment: Emergency Door Open: C7 1 Power Out (12VDC, 100mA) 3 Signal + 4 Signal - Install the ACX J1 key switch panel ACX J1 Pin Assignment for Key Switch Pin Type Function Wire Color 1 Red (V-) Red 2 LED Green (V-) Green 3 VCC (12V) Black 4 Key N.O Amber 5 COM (for Key and Tamper) White 6 Tamper N.O Brown S- S+ GND 12V Control Panel C7 for 8901 C10 for 8902 Version C Design. Innovations Page 17 of 17

INTELLIGENT CONTROL MODULE SA-2000-II HARDWARE MANUAL. Access Technologies International, Inc.

INTELLIGENT CONTROL MODULE SA-2000-II HARDWARE MANUAL. Access Technologies International, Inc. SA-2000-II HARDWARE MANUAL Access Technologies International, Inc. 1 Table of Contents 1. Introduction 3 2. Features 3 3. Specification 4 4. Identifying Supplied Parts 4 5. Panel Description 5 6. Connection