Panasonic Surface mount type Aluminum Electrolytic Capacitor ( V type FK series ) Surface Mount Low impedance High Reliability For Power Supply
|
|
|
- Juliet Harmon
- 7 years ago
- Views:
Transcription
1 New TENTATIVE Vertical chip type FK series Surface Mount Low impedance High Reliability For Power Supply Features Low impedance (40 to 60% lower than FC series) Miniaturization (30 to 50% less than FC series) Life time : 2000 to 5000 hours at 105 C Specifications Category Temperature Range Rated W. V. Range Nominal Capacitance Range -55 to +105 C 6. 3 to 100 V. DC 3.3 to 6800uF Capacitance Tolerance +-20% ( 120 Hz/20 C ) Leakage Current I = 0. 01CV or 3 (ua ) ( Whichever is greater ) After application of rated working voltage for 2 minutes at +20 C Dissipation Factor (tan d) W.V. (V.DC) tan d (max) Add 0.02 per 1000uF for products of 1000uF or more. ( 120 Hz/20 C ) Endurance After the life test with DC rated working voltage at C for 5000 hours (dia.4 to 10 is 2000 hours), the capacitors shall meet the specified below. Post-test requirements at +20 C. Capacitance Change +-30% of the initially measured value Tan d DC Leakage Current Under 200% of the initially specified value Under the initially specified value Shelf Life After storage for 1000 hours at C with no voltage applied and then being stabilized at +20 C, capacitors shall meet the limits specified in Endurance. 1
2 Description of Part Number E E V F K Common code Series code W. V. code Capacitance code Suffix Common code V type R: W = 12mm 4 x 5.8(B), 5 x 5.8 (C) W. V. code j A C E V H J K 2A P: W = 16mm 6.3 x 5.8(D), 8x6.2 (E) W. V. ( V ) P: W = 24mm 8x10.2(F), 10x10.2(G) Q: W = 32mm 12.5x13.5(H13) M: W = 44mm 16x16.5(J16), 18x16.5 (K16) Capacitance : The first 2 figures are actual values and third denotes the number of zeros. R denotes the decimal point and all figures are the actual number with R. Examples ; 4. 7uF:4R7 10uF: uF: uF:102 Dimensions ( mm ) Not to scale < Dia to 18 > Working Voltage mark < Dia. 4 to 10 > 0.3 max A K (I) FK FK Dia H (P) Series Capacitance(uF) (Abbreviate to date code) L W ( ) Reference size (I) [mm] Working voltage mark j 6. 3V A 10V C 16V E 25V V 35V H 50V J 63V K 80V 2A 100V code D L A H max I W P K B 4 C 5 D 6.3 E 8 F 8 G 10 H J K
3 Case, Capacitance, and Table. /ESR : (ohm) at + 20 C 100( khz ) Current : ( ma rms ) at +105 C 100( khz ) W. V. (V)DC Cap. (uf) /ESR 10 B B B C(B) 0.7(1.35) 160(90) 33 C(B) 0.7(1.35) 160(90) 47 C(B) 0.7(1.35) 160(90) D(C) 0.36(0.7) 240(160) 100 D(C) 0.36(0.7) 240(160) D D E E E F F F F F F G G H H H J J K J K W. V. (V) DC Cap. (μf) /ESR 4. 7 B B B C(B) 0.7(1.35) 160(90) D(C) 0.88(1.52) 165(85) 22 C C D D(C) 0.36(0.7) 240(160) D E D D E E F F F F G F G H H G H H H J J J
4 Case, Capacitance, impedance and ripple Table. : (ohm) at +20 C 100( khz ) : ( ma rms ) at +105 C 100( khz ) W. V. (V)DC Cap. (uf) /ESR 3.3 C C D D E E F F F F G H H G H H J H K J J K K code B : Dia. 4 x 5.8L C : Dia. 5 x 5.8L D : Dia. 6.3 x 5.8L E : Dia. 8 x 6.2L F : Dia. 8 x 10. 2L G : Dia. 10 x 10. 2L H13 : Dia x 13.5L J16: Dia. 16 x 16.5L K16: Dia. 18 x 16.5L [mm] ( ):Miniaturization type 4
5 Reflow Soldering At reflow soldering, the temperature at surface of the capacitor shall not exceed the allowable range described below. <Diagram 1 > Temperature on capacitor surface( C) below 160 C 120sec 5sec Peak temperature Duration(S) (temp > 200 C) Time(S) < Diagram 2 > Peak temperature/duration(temp>200 C(S)) 240 Peak temperature/duration (temp>200 C(S)) 240 Peak temperature( C) Peak temperature( C) Duration(temp>200 C(S)) Duration(temp>200 C(S)) Reflow soldering of size code B, C, and D Reflow soldering of size code E, F, G, H13,J16 and K16 For reflow,use a thermal condition system such as infrared reduction(ir)or hot blast. Vapor phase soldering systems (VPS) are not recommended. The contents of this tentative catalog are subject of change without notice in advance. TEL: ,4466 FAX: Matsushita Electronic Components Co., Ltd.Capacitor Division. TEL ( Dial In ) FAX
handbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing Extended voltage and capacitance range SMD-version, fully moulded, insulated Flexible terminals, reflow and wave solderable
SMD Aluminum Solid Capacitors with Conductive Polymer
SMD Aluminum Solid Capacitors with Conductive Polymer FEATURES New OS-CON series provides improved characteristics with up to 25 C temperature capability and 35 V maximum voltage rating in a SMD package
Application Note TMA Series
1W, SIP, Single & Dual Output DC/DC Converters Features SIP Package with Industry Standard Pinout Package Dimension: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 5V&12V Models 19.5 x 10.2 x 7.1 mm (0.77 x
Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability
Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability 048 RML 48 RUS lower longer life 36 RVI miniaturize 50 RMI high vibration FEATURES Very long useful life: 7000
Capacitance Cap. Tol. Suffix construction. Rated voltage
Metallized Polypropylene Film Capacitors Type:ECWFE Plastic Film Capacitors Non-inductive construction using metalized Polypropylene film with flame retardant plastic case. Features Small size Excellent
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
SuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal
SuperTan Extended () Capacitors, Wet Tantalum Capacitors with Hermetic Seal FEATURES SuperTan Extended () represents a major breakthrough in wet tantalum capacitor Available technology. Its unique cathode
Kit 27. 1W TDA7052 POWER AMPLIFIER
Kit 27. 1W TDA7052 POWER AMPLIFIER This is a 1 watt mono amplifier Kit module using the TDA7052 from Philips. (Note, no suffix.) It is designed to be used as a building block in other projects where a
SURFACE MOUNT LED LAMP STANDARD BRIGHT 0606
PACKAGE DIMENSIONS 0.075 (1.9) 0.063 (1.6) 0.035 (0.9) TOP 0.047 (1.2) 0.012 (0.3) 0.032 [0.8] SIDE 0.043 [1.1] 1 3 0.020 [0.5] 2 4 BOTTOM CATHODE MASK 1 2 3 4 HER / AlGaAs Red / Yellow (for-34) Green
Powering Integrated Circuits (ICs), and managing ripple voltage as it relates
Ripple Voltage & ESR Powering Integrated Circuits (ICs), and managing ripple voltage as it relates to ESR of capacitors Low voltage ICs require supply voltage (Vcc) to have reduced levels of ripple voltage
28 Volt Input - 40 Watt
Features Powers 28 volt dc-dc converters during power dropout Input voltage 12 to 40 volts Operating temperature -55 to +125 C Reduces hold-up capacitance by 80% Inhibit function Synchronization function
Types MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
RoHS APPROVAL SHEET. ituner 12V/6.6A SERIES NO. (E17) EA10953A. ( ) Edac Power Electronics (Suzhou) Co., Ltd. 59 No.59, Chang Sheng Road, Sheng Pu,
APPROVAL SHEET CUSTOMER ituner CUSTOMER P/N DESCRIPTION EDAC MODEL 12V/6.6A SERIES NO. (E17) EA10953A DATE 2010-06-22 REVISION 0 APPROVED DESIGN PREPARE RoHS CONCLUSION APPROVED CONDITON CUSTOMER S APP
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
LM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
DATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET 24 W BTL or 2 x 12 W stereo car radio File under Integrated Circuits, IC01 January 1992 GENERAL DESCRIPTION The is a class-b integrated output amplifier encapsulated in a
AS2815. 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response
1.5A Low Dropout oltage Regulator Adjustable & Fixed Output, Fast Response FEATURES Adjustable Output Down To 1.2 Fixed Output oltages 1.5, 2.5, 3.3, 5.0 Output Current of 1.5A Low Dropout oltage 1.1 Typ.
Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description
MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four
LM1084 5A Low Dropout Positive Regulators
5A Low Dropout Positive Regulators General Description The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5 at 5A of load current. It has the same pin-out as
Type MLS 125 C Flatpack, Ultra Long Life, Aluminum Electrolytic Now Available with High Vibration and High Reliability Options
Now Encased in rugged stainless steel, the MLS is perfect for high reliability military systems and applications operating above 85 C. For our highest performing 25 C Flatpacks, choose type HVMLS available
DYNACAP Double Layer Capacitor
DX Series (Terminal shaped V, H) Combines two coin cells using laser welding technology to obtain a rated voltage of 5.5V. Available in either vertical or horizontal terminal leads, they are 11.5 mm in
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator Description: The NTE923 and NTE923D are voltage regulators designed primarily for series regulator applications. By themselves, these devices
Type EDL, Electric Double Layer Supercapacitors Ultra High Capacitance, Small Case Size Options
Ultra High Capacitance, Small Case Size Options Type EDL electric double layer supercapacitors offer extremely high capacitance values (farads) in a variety of packaging options that will satisfy, low
Aluminum Capacitors Solid Axial
SAL-A End of Life. Last Available Purchase Date is -December- Radial higher CV/volume Fig. QUICK REFERENCE DATA DESCRIPTION VALUE Maximum case size (Ø D x L in mm) 6.7 x. to.9 x. Rated capacitance range
NOT RECOMMENDED FOR NEW DESIGNS
28 Volt NOT RECOMMENDED FOR NEW DESIGNS Features Attenuation 0 db from 110 khz to 0 MHz Operating temperature - to +8 C Nominal 28 V input, 0 V to 0 V operation 1.7 to A throughput current Transient suppression
Advanced Monolithic Systems
Advanced Monolithic Systems FEATURES Three Terminal Adjustable or Fixed oltages* 1.5, 1.8, 2.5, 2.85, 3.3 and 5. Output Current of 1A Operates Down to 1 Dropout Line Regulation:.2% Max. Load Regulation:.4%
Series AMLDL-Z Up to 1000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Series Up to ma LED Driver Models Single output Model Input Voltage (V) Step Down DC/DC LED driver Operating Temperature range 4ºC to 85ºC
EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet Chip LED with Bi-Color (Multi-Color) Features Package in 8mm tape on 7 diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow
LM3940 1A Low Dropout Regulator for 5V to 3.3V Conversion
1A Low Dropout Regulator for 5V to 3.3V Conversion General Description The LM3940 is a 1A low dropout regulator designed to provide 3.3V from a 5V supply. The LM3940 is ideally suited for systems which
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
High Precision TCXO / VCTCXO Oscillators
Available at Digi-Key** www.digikey.com High Precision TCXO / VCTCXO Oscillators 2111 Comprehensive Drive Phone: 60-81- 722 Fax: 60-81- 00 US Headquarters: 60-81-722 European Headquarters: +-61-72221 Description:
Electrical Double Layer Energy Storage Capacitors Power and Energy Versions
Electrical Double Layer Energy Storage Capacitors Power and Energy Versions FEATURES Polarized energy storage capacitor with high capacity and energy density Energy version with high stability available
LM118/LM218/LM318 Operational Amplifiers
LM118/LM218/LM318 Operational Amplifiers General Description The LM118 series are precision high speed operational amplifiers designed for applications requiring wide bandwidth and high slew rate. They
DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The is an integrated class-b output amplifier in a 13-lead single-in-line (SIL) plastic power package.
* Requires external power line filter and hold up capacitors; see typical applica on circuit and app notes for details
The 8500 module contains all of the necessary circuitry for complete power line compliance with aeronau cs specifica on RTCA/DO 60G and Boeing's D6 36440(C)*. It is a pin for pin and form fit compa ble
INTEGRATED CIRCUITS DATA SHEET. TDA7052 1 W BTL mono audio amplifier. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET TDA7052 1 W BTL mono audio amplifier File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The TDA7052 is a mono output amplifier in a 8-lead dual-in-line (DIL)
P O W E R C A P A C I T O R A S S E M B L I E S
AMERICAN TECHNICAL CERAMICS P O W E R C A P A C I T O R A S S E M B L I E S ISO 9001 REGISTERED COMPANY Overview About ATC Power Assemblies ATC standard & custom Power Assemblies are fabricated from PARALLEL
Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring
Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION VALUE 00 0 Nominal case size (Ø D x L in mm) x 0 to 0 x 00 Rated capacitance range 0 μf to
Y.LIN ELECTRONICS CO.,LTD.
Features Current transfer ratio (CTR 50~600% at I F =5mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Creepage distance >7.62 mm Operating temperature up to +110 C Compact
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type MKT80 FEATURES AEC-Q00 qualified (rev. D) for PCM. mm (for larger available components on request) High temperature capabilities, up to 0 C Capacitance up to 60
SUCCESS EPCOS Capacitors
SUCCESS EPCOS Inc. Capacitors Group April, 2012 EV / HV / E-Mobility Battery charger system & Inverter On Board and Off Board Assembly Trend: Wireless Charging DC/DC Converter Filtering DC Link E-Mobility
EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet 0603 Package Chip LED (0.8 mm Height) Features Package in 8mm tape on 7 diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
Spezifikation für Freigabe / specification for release
Artikelnummer / part number : 82550350 Datum / Date : 31.07.06 description : 0805 SMD VARISTOR Lead Free SMD size: 0805 ROHS Compliant A Mechanische Abmessungen / dimensions : SIZE SIZE W L T a 0402 0.5
LM138 LM338 5-Amp Adjustable Regulators
LM138 LM338 5-Amp Adjustable Regulators General Description The LM138 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 5A over a 1 2V to 32V output range
L78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
High-Speed, 5 V, 0.1 F CMOS RS-232 Driver/Receivers ADM202/ADM203
a FEATURES kb Transmission Rate ADM: Small (. F) Charge Pump Capacitors ADM3: No External Capacitors Required Single V Power Supply Meets EIA-3-E and V. Specifications Two Drivers and Two Receivers On-Board
INTELLIGENT INTERACTIVE SYNTHESIZER SURFACE MOUNT MODEL: MFSH615712-100
SURFACE MOUNT MODEL: MFSH6572 65-72 MHz FEATURES: Small Size, Surface Mount (.6" x.6") Low Phase Noise Standard Programming Interface Ultra Wide Tuning Range Lead Free - RoHS Compliant Patented REL-PRO
Aluminum Electrolytic Capacitors Power Economic Printed Wiring
Aluminum Electrolytic Capacitors Power Economic Printed Wiring 0/0 PECPW 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION high ripple current 0/0 PECPW long life 0 C Nominal case size (Ø D x L in mm) Rated
S112-XHS. Description. Features. Agency Approvals. Applications. Absolute Maximum Ratings. Schematic Diagram. Ordering Information
Description Features The S112-X is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. The circuit is composed of one input IR LED with a series limiting resistor
Delphi Series V48SH, 1/16 th Brick 35W DC/DC Power Modules: 48V in, 1.0V, 35A out
Delphi Series V48SH, 1/16 th Brick 35W DC/DC Power Modules: 48V in, 1.0V, 35A out The Delphi Series V48SH, 1/16 th Brick, 48V input, single output, isolated DC/DC converter, is the latest offering from
STLQ015. 150 ma, ultra low quiescent current linear voltage regulator. Description. Features. Application
150 ma, ultra low quiescent current linear voltage regulator Description Datasheet - production data Features SOT23-5L Input voltage from 1.5 to 5.5 V Very low quiescent current: 1.0 µa (typ.) at no load
High Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator ADP3339
Data Sheet High Accuracy, Ultralow IQ,.5 A, anycap Low Dropout Regulator FEATURES FUNCTIONAL BLOCK DIAGRAM High accuracy over line and load: ±.9% at 5 C, ±.5% over temperature Ultralow dropout voltage:
CMOS Switched-Capacitor Voltage Converters ADM660/ADM8660
CMOS Switched-Capacitor Voltage Converters ADM66/ADM866 FEATURES ADM66: Inverts or Doubles Input Supply Voltage ADM866: Inverts Input Supply Voltage ma Output Current Shutdown Function (ADM866) 2.2 F or
Current and Temperature Ratings
Document 361-1 Current and Temperature Ratings Introduction This application note describes: How to interpret Coilcraft inductor current and temperature ratings Our current ratings measurement method and
LF00AB/C SERIES VERY LOW DROP VOLTAGE REGULATORS WITH INHIBIT
LF00AB/C SERIES ERY LOW DROP OLTAGE REGULATORS WITH INHIBIT ERY LOW DROPOUT OLTAGE (5) ERY LOW QUIESCENT CURRENT (TYP. 50 µa IN OFF MODE, 500µA INON MODE) OUTPUT CURRENT UP TO 500 ma LOGIC-CONTROLLED ELECTRONIC
Silvertel. Ag5200. 1 Features. 2 Description. Power-over-Ethernet Plus Module. IEEE802.3at and IEEE802.3af compliant. Maximum 30W output power
Silvertel V1.1 November 2012 Datasheet Pb 1 Features IEEE802.3at and IEEE802.3af compliant Maximum 30W output power Dual In-Line (DIL) package size 50.6mm (L) x 30mm (W) Overload, short-circuit and thermal
EVERLIGHT ELECTRONICS CO., LTD.
ECN : PAGE : 1/7 Features : Fast response time High photo sensitivity Small junction capacitance High reliability Description : is a high speed silicon NPN epitaxial planar phototransistor in a compact
AC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
DATA SHEET. TDA8560Q 2 40 W/2 Ω stereo BTL car radio power amplifier with diagnostic facility INTEGRATED CIRCUITS. 1996 Jan 08
INTEGRATED CIRCUITS DATA SHEET power amplifier with diagnostic facility Supersedes data of March 1994 File under Integrated Circuits, IC01 1996 Jan 08 FEATURES Requires very few external components High
50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
AZ420 MINIATURE GENERAL PURPOSE RELAY
MINIATURE GENERAL PURPOSE RELAY FEATURES Rugged construction for high reliability Life expectancy greater than 0 million operations DC coils to 11 V Power consumption as low as 2 mw per pole available
Chip Monolithic Ceramic Capacitors
This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it s specifications are subject to change or our products in it may be discontinued without advance notice.
LM117 LM317A LM317 3-Terminal Adjustable Regulator
LM117 LM317A LM317 3-Terminal Adjustable Regulator General Description The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1 5A over a 1 2V to 37V
Instruction Manual PFE300S 500S SERIES. TDK-Lambda PFE300S 500S Series INSTRUCTION MANUAL
PFE300S 500S SERIES Instruction Manual TDK-Lambda PFE300S 500S Series BEFORE USING THE POWER SUPPLY UNIT Be sure to read this instruction manual thoroughly before using this product. Pay attention to all
LM386 Low Voltage Audio Power Amplifier
Low Voltage Audio Power Amplifier General Description The LM386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count
INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components
Features. Applications. Truth Table. Close
ASSR-8, ASSR-9 and ASSR-8 Form A, Solid State Relay (Photo MOSFET) (0V/0.A/0Ω) Data Sheet Description The ASSR-XX Series consists of an AlGaAs infrared light-emitting diode (LED) input stage optically
O WA-120U series IP67. 120W Single Output Switching Power Supply. Features. Aplications
Features UniversalACinput/Fulrange Built-inactivePFCfunction Higheficiencyupto91% Protections:Shortcircuit/Overcurent/ Overvoltage/Overtemperature Fanlesdesign,colingbyfreairconvection Colingbyfreairconvection
Ceramic Trimmer Capacitors
!Note T3E8.pdf 2.9.2 Ceramic Trimmer Capacitors TZB4 Series.±. Depth.5.4±. dia. Features. Miniature rectangular shape : 4.(W)x4.5(L)x3.(H)mm. 2. Color coded case facilitates identification of capacitance
LM2941/LM2941C 1A Low Dropout Adjustable Regulator
LM2941/LM2941C 1A Low Dropout Adjustable Regulator General Description The LM2941 positive voltage regulator features the ability to source 1A of output current with a typical dropout voltage of 0.5V and
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK Typical Applications The HMC547LP3
Inductive Proximity Sensors
M12 Inductive Proximity Sensors Standard Length Mini's Extended Sensing 3 Wire DC 2 Wire DC 2 Wire AC (Wiring Schematic) 3 Wire DC PNP Normally Open (1) IMM32122C IMM35124C IMN32122C IMN35124C IMN32122M12
Metallized Polypropylene Film Capacitors DC-Link Capacitor
Metallized Polypropylene Film Capacitors DC-Link Capacitor FEATURES Slim line, low building height Very long useful life time: Up to 100 000 h at U NDC and 70 C High ripple current capability, low ESR,
LM79XX Series 3-Terminal Negative Regulators
LM79XX Series 3-Terminal Negative Regulators General Description The LM79XX series of 3-terminal regulators is available with fixed output voltages of b5v b8v b12v and b15v These devices need only one
CS8481. 3.3 V/250 ma, 5.0 V/100 ma Micropower Low Dropout Regulator with ENABLE
3.3 /250 ma, 5.0 /100 ma Micropower Low Dropout Regulator with The CS8481 is a precision, dual Micropower linear voltage regulator. The switched 3.3 primary output ( OUT1 ) supplies up to 250 ma while
MINIATURE SURFACE MOUNT RELAY
FTR-K1 SERIES MINIATURE SURFACE MOUNT RELAY 1 POLE - 25A (For Automotive Applications) FTR-P6 Series FEATURES Surface mount relays for automotive applications Miniature size (67% of the volume of FTR-P3
unit : mm With heat sink (see Pd Ta characteristics)
Ordering number: EN1321E Monolithic Linear IC LA4261 3.5 W 2-Channel AF Power Amplifier for Home Stereos and Music Centers Features. Minimum number of external parts required (No input capacitor, bootstrap
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
Symbol Parameter Value Unit V i-o Input-output Differential Voltage 40 V I O Output Current Intenrally Limited Top
LM117/217 LM317 1.2V TO 37V VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE : 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 1.5A 0.1% LINE AND LOAD REGULATION FLOATING OPERATION FOR HIGH VOLTAGES COMPLETE SERIES OF PROTECTIONS
VT-802 Temperature Compensated Crystal Oscillator
T-802 Temperature Compensated Crystal Oscillator T-802 Description ectron s T-802 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, CMOS output, analog temperature compensated oscillator,
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338 FEATURES High accuracy over line and load: ±.8% @ 25 C, ±1.4% over temperature Ultralow dropout voltage: 19 mv (typ) @ 1 A Requires
TL783C, TL783Y HIGH-VOLTAGE ADJUSTABLE REGULATOR
HIGH-VOLTAGE USTABLE REGULATOR SLVS36C SEPTEMBER 1981 REVISED APRIL 1997 Output Adjustable From 1.25 V to 125 V When Used With an External Resistor Divider 7-mA Output Current Full Short-Circuit, Safe-Operating-Area,
LDS8720. 184 WLED Matrix Driver with Boost Converter FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
184 WLED Matrix Driver with Boost Converter FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier) 250 mv
Data Sheet. Nationstar LED
Data Sheet Nationstar LED 1 Table of Contents General Informations:... 3 Electrical and Flux Characteristics... 3 Color Wavelength Diagram:... 6 Mechanical Dimensions:... 7 Electrical Connection:... 7
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
WCAP-CSGP Ceramic Capacitors
A Dimensions: [mm] B Recommended land pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1±0.2 Vrms, 1 khz ±10% C 15000 pf ± 10% Rated voltage Dissipation factor
Chip Diode Application Note
Chip Diode Application Note Introduction The markets of portable communications, computing and video equipment are challenging the semiconductor industry to develop increasingly smaller electronic components.
UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming
Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit Protected Pinned
LM1036 Dual DC Operated Tone/Volume/Balance Circuit
LM1036 Dual DC Operated Tone/Volume/Balance Circuit General Description The LM1036 is a DC controlled tone (bass/treble), volume and balance circuit for stereo applications in car radio, TV and audio systems.
Guide for Molded Tantalum Capacitors
Guide for Molded Tantalum Capacitors INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability,
TDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS650-44 Description The ICS650-44 is a spread spectrum clock synthesizer intended for video projector and digital TV applications. It generates three copies of an EMI optimized 50 MHz clock
High-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
LM350. 3.0 A, Adjustable Output, Positive Voltage Regulator THREE TERMINAL ADJUSTABLE POSITIVE VOLTAGE REGULATOR
3. A, able Output, Positive Voltage Regulator The is an adjustable threeterminal positive voltage regulator capable of supplying in excess of 3. A over an output voltage range of 1.2 V to 33 V. This voltage
LM2941 LM2941C 1A Low Dropout Adjustable Regulator
June 1994 LM2941 LM2941C 1A Low Dropout Adjustable Regulator General Description The LM2941 positive voltage regulator features the ability to source 1A of output current with a typical dropout voltage
Type MLP 85 C Flatpack, Ultra Long Life, Aluminum Electrolytic Very Low Profile
The MLP s high-energy storage and box-shape make it perfect for voltage holdup or filtering in military SEM-E modules, telecom circuit packs and computer cards. The MLP delivers up to 20 joules of energy
1.5A Very L.D.O Voltage Regulator LM29150/29151/29152
FEATURES High Current Capability 1.5A Low Dropout Voltage 350mV Low Ground Current Accurate 1% Guaranteed Initial Tolerance Extremely Fast Transient Response Reverse-Battery and "Load Dump" Protection
DATA SHEET THICK FILM CHIP RESISTORS Introduction
DATA SHEET THICK FILM CHIP RESISTORS Introduction Product Specification Product specification 2 Chip Resistor Surface Mount Data in data sheets is presented - whenever possible -according to a 'format',