TryItNow! Step by Step Walkthrough: Spoiler Support

Size: px
Start display at page:

Download "TryItNow! Step by Step Walkthrough: Spoiler Support"

Transcription

1 TryItNow! Step by Step Walkthrough: Spoiler Support ANSYS, Inc. March 28, 2016

2 TryItNow! Step by Step Walkthrough: Spoiler Support ANSYS designed this TryItNow! experience to give you quick access to ANSYS AIM simulations on the cloud. This AIM demonstration shows the air flow over an automotive rear spoiler and the resulting stresses in the spoiler support. The simulation demonstrates the ease of setting up and solving a multiphysics simulation. This geometry has been processed in SpaceClaim to use half the symmetric part and add a fluid flow enclosure around the structure ANSYS, Inc. March 28, 2016 Ready to learn more about ANSYS AIM? CONTACT US

3 Select Fluid-Structure Interaction Template Select the Fluid-Structure Interaction Template from the Study menu in AIM ANSYS, Inc. March 28, 2016

4 Modify Template Settings 1. Turn off structural contact detection. This is more efficient when there is only one structural part. 2. Turn on configuration to more easily work with separate solid and fluid parts. 3. Select Create Simulation Process and select the geometry file spoiler.scdoc to execute the template ANSYS, Inc. March 28, 2016

5 Task Based Workflow The necessary simulation tasks are created, and the geometry loaded ANSYS, Inc. March 28, 2016

6 Suppress the solid part in the Flow simulation 2. Selection filters enable you to switch between selecting points, lines, surfaces or bodies. Turn on the Body selection filter. 3. Left-click to select the spoiler body. 1. Select the Configuration task for the Flow simulation. 4. Right-click and add a Suppress Control to the body. 5. Right-click and update the configuration ANSYS, Inc. March 28, 2016

7 Specify Mesh Inflation 3. Use Automatically Defined to select all unlabeled surfaces 2. Right-click and use the Fix menu to navigate to Inflation 1 1. Select the Mesh task ANSYS, Inc. March 28, 2016

8 Generate and Review Mesh Right-click to Generate Mesh and review the result ANSYS, Inc. March 28, 2016

9 The Physics Panel Select the Flow Task and review the physics panel. The initial settings are automated based on the selected template. In each section you can review the setup and modify it based on your own requirements. The material assignments, physics options and solver options can all be reviewed ANSYS, Inc. March 28, 2016

10 Specify Inlet conditions 3. Right-click and Add an Inlet Boundary Condition. 2. Select the Inlet face. 1. Activate the Face selection filter. 4. Specify inlet velocity of 80 mile/hr (36 m/s) ANSYS, Inc. March 28, 2016

11 Specify Outlet Boundary 1. Select the Outlet face. 2. Right-click and Add an Outlet Boundary Condition. 3. Specify the outlet Pressure as 0 Pa ANSYS, Inc. March 28, 2016

12 Specify Far Field Boundary 1. Using Ctrl-left click, select the two far field faces. 2. Right-click and Add an Opening boundary condition. 3. Specify an entrainment pressure of 0 Pa ANSYS, Inc. March 28, 2016

13 Specify Symmetry Boundary 1. Select the Symmetry face. 2. Right-click and Add a Symmetry boundary condition ANSYS, Inc. March 28, 2016

14 Specify Wall Boundary Right-click and a add Wall boundary condition. (AIM will automatically select all surfaces without a boundary condition specification for the wall.) ANSYS, Inc. March 28, 2016

15 Optional, Increase number of Solver processes From the Flow physics panel, navigate to Solver Options/Solver Settings/Launch Controls, and set the number of processes. Hit Apply when done. AIM always runs in parallel, using 2 processes by default. You can accelerate solution time by increasing the number of processes (to a maximum of 6 for Try It Now) ANSYS, Inc. March 28, 2016

16 Update Flow solution Right-click on the Flow task and select Update to execute solution. The Solution Quality tab can be used to monitor convergence. This case defaults to moderate convergence sufficient for demonstration purposes ANSYS, Inc. March 28, 2016

17 Visualize Pressure Field 2. Right-click and add a Contour Result. 3. Select the Wall from the Location dropdown, and Pressure for the Variable. 4. Right-click and evaluate the Result. 1. Select the Results task for the Flow simulation ANSYS, Inc. March 28, 2016

18 Suppress the flow volume in the Structural simulation 3. Left-click to select the flow volume body. 2. Turn on the Body selection filter. 1. Select the Configuration task for the Structural simulation. 4. Right-click and add a Suppress Control to the body. 5. Right-click and update the configuration ANSYS, Inc. March 28, 2016

19 Specify Structural Support 3. Select the support bottom face. 1. Ensure the Face selection filter is active. 4. Right-click and add a Support Boundary Condition 2. Select the Structural Task ANSYS, Inc. March 28, 2016

20 Specify symmetry displacement condition 1. Select the spoiler mid face. 2. Right-click and add a Displacement Boundary Condition 3. Change the definition to Normal to boundary, and set a 0 displacement ANSYS, Inc. March 28, 2016

21 Specify surfaces for flow pressure load 3. Hit the + button to add the selection as the target of the pressure load. 2. Using Shift-Left Mouse, box select all the structural faces. 1. Select the Physics Coupling object from the Fix menu ANSYS, Inc. March 28, 2016

22 Update Results (and Structural solution) Right-click the Structural Results task, and select Update to generate the mesh, execute the solution, and calculate results ANSYS, Inc. March 28, 2016

23 Post-process Equivalent Stress Results 1. Select the Results task, and use the Search and Select bar to pick the Equivalent Stress Result. 2. Right-click to animate the results ANSYS, Inc. March 28, 2016

24 TryItNow! Step by Step Walkthrough: Spoiler Support Ready to learn more about ANSYS AIM? CONTACT US ANSYS, Inc. March 28, 2016

Tutorial 1. Flow over a Cylinder Two Dimensional Case. Using ANSYS Workbench. Simple Mesh

Tutorial 1. Flow over a Cylinder Two Dimensional Case. Using ANSYS Workbench. Simple Mesh Tutorial 1. Flow over a Cylinder Two Dimensional Case Using ANSYS Workbench Simple Mesh The primary objective of this Tutorial is to guide the student using Fluent for first time through the very basics

More information

Steady Flow: Laminar and Turbulent in an S-Bend

Steady Flow: Laminar and Turbulent in an S-Bend STAR-CCM+ User Guide 6663 Steady Flow: Laminar and Turbulent in an S-Bend This tutorial demonstrates the flow of an incompressible gas through an s-bend of constant diameter (2 cm), for both laminar and

More information

FLUENT Lab Exercise 10 Ahmed Car body

FLUENT Lab Exercise 10 Ahmed Car body FLUENT Lab Exercise 10 Ahmed Car body Introduction The purpose of this exercise is to introduce you to 3D meshing and post processing. This will show you the power of ANSYS meshing. The problem involves

More information

Verification and Validation of Turbulent Flow around a Clark-Y Airfoil

Verification and Validation of Turbulent Flow around a Clark-Y Airfoil Verification and Validation of Turbulent Flow around a Clark-Y Airfoil 58:160 Intermediate Mechanics of Fluids CFD LAB 2 By Timur Dogan, Michael Conger, Maysam Mousaviraad, Tao Xing and Fred Stern IIHR-Hydroscience

More information

ANSYS AIM Simulation for Every Engineer AIM Program Management

ANSYS AIM Simulation for Every Engineer AIM Program Management ANSYS AIM Simulation for Every Engineer AIM Program Management 1 2015 ANSYS, Inc. September 27, 2015 Today s Simulation Challenges Leveraging simulation across engineering organizations Gaining simulation

More information

1. Start the NX CAD software. From the start menu, select Start All Programs UGS NX 8.0 NX 8.0 or double click the icon on the desktop.

1. Start the NX CAD software. From the start menu, select Start All Programs UGS NX 8.0 NX 8.0 or double click the icon on the desktop. Lab Objectives Become familiar with Siemens NX finite element analysis using the NX Nastran solver. Perform deflection and stress analyses of planar truss structures. Use modeling and FEA tools to input

More information

Set up and solve a transient problem using the pressure-based solver and VOF model.

Set up and solve a transient problem using the pressure-based solver and VOF model. Tutorial 18. Using the VOF Model Introduction This tutorial examines the flow of ink as it is ejected from the nozzle of a printhead in an inkjet printer. Using ANSYS FLUENT s volume of fluid (VOF) multiphase

More information

Tutorial 23. Using the Eulerian Granular Multiphase Model with Heat Transfer

Tutorial 23. Using the Eulerian Granular Multiphase Model with Heat Transfer Tutorial 23. Using the Eulerian Granular Multiphase Model with Heat Transfer Introduction This tutorial examines the flow of air and a granular solid phase consisting of glass beads in a hot gas fluidized

More information

Customer Training Material. Oblique Projectile Impact. ANSYS Explicit STR. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved.

Customer Training Material. Oblique Projectile Impact. ANSYS Explicit STR. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved. Workshop 14 Oblique Projectile Impact Introduction to ANSYS Explicit STR WS14-1 Workshop Goal and Procedure Goal: Perform oblique impact / penetration analysis (with erosion) Procedure: Create an Explicit

More information

Levee with Toe Drain. Topics Covered. Seepage analysis Levee drainage Multiple materials Phreatic surface Groundwater only calculation Flownets

Levee with Toe Drain. Topics Covered. Seepage analysis Levee drainage Multiple materials Phreatic surface Groundwater only calculation Flownets Levee with Toe Drain 15-1 Levee with Toe Drain In this tutorial, finite element groundwater seepage analysis is used to simulate a levee with a horizontal toe drain. Toe drains are often used to prevent

More information

Plan for today (two exercises) 1: CAD, CFD, FEM Fluid-Structure interaction (FSI) Numerical Methods in Aerodynamics http://www.ansys.com/solutions/fluid-dynamics.asp http://www-harwell.ansys.com/demoroom/details.php?id=11,112

More information

Set up and solve a transient problem using the pressure-based solver and VOF model.

Set up and solve a transient problem using the pressure-based solver and VOF model. Tutorial 18. Using the VOF Model This tutorial was run using ANSYS FLUENT 12.1. The results have been updated to reflect the change in the default setting of node-based smoothing for the surface tension

More information

Simulation of Turbulent Flow over the Ahmed Body

Simulation of Turbulent Flow over the Ahmed Body 1 Simulation of Turbulent Flow over the Ahmed Body 58:160 Intermediate Mechanics of Fluids CFD LAB 4 By Timur Dogan, Michael Conger, Maysam Mousaviraad, Tao Xing and Fred Stern IIHR-Hydroscience & Engineering

More information

Customer Training Material. Tank Flushing Example ANSYS FLUENT. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved.

Customer Training Material. Tank Flushing Example ANSYS FLUENT. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved. Workshop 7 Tank Flushing Example Introduction to ANSYS FLUENT WS7-1 Introduction In this workshop, you will model the filling and emptying of a water tank. The transient problem is solved as a multiphase

More information

Flow Modelling in Heat- Exchangers using ANSYS CFX

Flow Modelling in Heat- Exchangers using ANSYS CFX Flow Modelling in Heat- Exchangers using ANSYS CFX By Ahmed Al Makky @Ahmed Al Makky 2012 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted

More information

Tutorial: Heat and Mass Transfer with the Mixture Model and Evaporation-Condensation Model

Tutorial: Heat and Mass Transfer with the Mixture Model and Evaporation-Condensation Model Tutorial: Heat and Mass Transfer with the Mixture Model and Evaporation-Condensation Model Introduction The purpose of this tutorial is to demonstrate the solution of a multiphase problem involving heat

More information

Flow Modelling in a Porous-Fluid Domain using ANSYS CFX

Flow Modelling in a Porous-Fluid Domain using ANSYS CFX Flow Modelling in a Porous-Fluid Domain using ANSYS CFX First Edition Ahmed Al Makky @Ahmed Al Makky 2012 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system

More information

Creating Macros In Word 2013

Creating Macros In Word 2013 Creating Macros In Word 2013 Contents in Word 2013... 1 What is a Macro?... 1 Instructions for :... 1 Step 1 Display the Marco Recording Button... 1 Step 2 - Create a Macro Button... 2 Step 3 - Begin Recording

More information

Using SolidWorks Flow Simulation to Calculate the Flow Around a NACA5012 Aerofoil

Using SolidWorks Flow Simulation to Calculate the Flow Around a NACA5012 Aerofoil Using SolidWorks Flow Simulation to Calculate the Flow Around a NACA5012 Aerofoil Introduction This note explains how to draw an aerofoil in three dimensions in SolidWorks and then how to run a simple

More information

Define time-dependent boundary conditions with a user-defined function (UDF). Automatically save data files at defined points during the solution.

Define time-dependent boundary conditions with a user-defined function (UDF). Automatically save data files at defined points during the solution. Tutorial 17. Using the VOF Model Introduction This tutorial examines the flow of ink as it is ejected from the nozzle of a printhead in an inkjet printer. Using FLUENT s volume of fluid (VOF) multiphase

More information

Geometry Consider a flat plate of zero thickness standing vertically. The surrounding air is at 40F while the plate itself is at 53F.

Geometry Consider a flat plate of zero thickness standing vertically. The surrounding air is at 40F while the plate itself is at 53F. CFX Tutorial Geometry Consider a flat plate of zero thickness standing vertically. The surrounding air is at 40F while the plate itself is at 53F. Due to the temperature difference between the plate and

More information

Multi-Phase Flow Tutorials

Multi-Phase Flow Tutorials STAR-CCM+ User Guide 3987 Multi-Phase Flow Tutorials The tutorials in this set illustrate various STAR-CCM+ facilities for simulating multi-phase fluid flow problems. These comprise: A gravity-driven free-surface

More information

Calculate a solution using the pressure-based solver.

Calculate a solution using the pressure-based solver. Tutorial 13. Using Dynamic Meshes Introduction In ANSYS FLUENT the dynamic mesh capability is used to simulate problems with boundary motion, such as check valves and store separations. The building blocks

More information

Using SolidWorks for Finite Element Analysis in 12 Easy Steps

Using SolidWorks for Finite Element Analysis in 12 Easy Steps Using SolidWorks for Finite Element Analysis in 12 Easy Steps 1. Before starting the FEA of the structure, do some hand calculations to determine approximately what results (stresses or deflections) you

More information

Modeling Periodic Flow and Heat Transfer

Modeling Periodic Flow and Heat Transfer Tutorial 2. Modeling Periodic Flow and Heat Transfer Introduction Many industrial applications, such as steam generation in a boiler or air cooling in the coil of an air conditioner, can be modeled as

More information

Structural Optimization of the Pole Mount Supports of a Solar Panel in a Wind Load Case Study

Structural Optimization of the Pole Mount Supports of a Solar Panel in a Wind Load Case Study Structural Optimization of the Pole Mount Supports of a Solar Panel in a Wind Load Case Study Mono-objective Optimization www.ozeninc.com/optimization optimization@ozeninc.com Optimization Applied to a

More information

Air conditioning simulation ANSYS Workbench Ott Pabut

Air conditioning simulation ANSYS Workbench Ott Pabut Air conditioning simulation ANSYS Workbench 11.00 Ott Pabut Tallinn 2010 Task Set up air conditioning simulation with program Ansys Workbench. inlet heater door windows outlet thermometer Fig1 - Task 1.1

More information

Modeling Periodic Flow and Heat Transfer

Modeling Periodic Flow and Heat Transfer Tutorial 2. Modeling Periodic Flow and Heat Transfer Introduction Many industrial applications, such as steam generation in a boiler or air cooling in the coil of an air conditioner, can be modeled as

More information

Multiphase Flow - Appendices

Multiphase Flow - Appendices Discovery Laboratory Multiphase Flow - Appendices 1. Creating a Mesh 1.1. What is a geometry? The geometry used in a CFD simulation defines the problem domain and boundaries; it is the area (2D) or volume

More information

Customer Training Material. Modeling Multi-Species Flow ANSYS FLUENT. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved.

Customer Training Material. Modeling Multi-Species Flow ANSYS FLUENT. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved. Workshop 3 Modeling Multi-Species Flow Introduction to ANSYS FLUENT WS3-1 Introduction (1) In this workshop you will analyze the release of heat and combustion gases from a single car with an engine fire

More information

Simulation of Turbulent Flow in an Asymmetric Diffuser

Simulation of Turbulent Flow in an Asymmetric Diffuser 1 Simulation of Turbulent Flow in an Asymmetric Diffuser ME:5160 Intermediate Mechanics of Fluids CFD LAB 3 (ANSYS 17.1; Last Updated: Oct. 6, 2016) By Timur Dogan, Michael Conger, Dong-Hwan Kim, Andrew

More information

First Steps - Ball Valve Design

First Steps - Ball Valve Design 1 First Steps - Ball Valve Design This First Steps tutorial deals with the flow of water through a ball valve assembly before and after some design changes. The objective is to show how easy fluid flow

More information

Determining the drag force with CFD method ANSYS Workbench Ott Pabut

Determining the drag force with CFD method ANSYS Workbench Ott Pabut Determining the drag force with CFD method ANSYS Workbench 11.00 Ott Pabut Tallinn 2010 Task 1 Determine analytically and with CFD method the moment which is generated on the foundation of the water tower.

More information

Event Services Event Management Software Training Manual

Event Services Event Management Software Training Manual Event Services Event Management Software Training Manual Quick Links: How to create an account Using the Browsing Tools Making a Reservation Request Event Services Page 1 How to create an account STEP

More information

GAMBIT Demo Tutorial

GAMBIT Demo Tutorial GAMBIT Demo Tutorial Wake of a Cylinder. 1.1 Problem Description The problem to be considered is schematically in fig. 1. We consider flow across a cylinder and look at the wake behind the cylinder. Air

More information

c Fluent Inc. November 27,

c Fluent Inc. November 27, Tutorial 15. Using the VOF Model Introduction: This tutorial illustrates the setup and solution of the two-dimensional turbulent fluid flow in a partially filled spinning bowl. In this tutorial you will

More information

Finite Element Modules for Enhancing Undergraduate Transport Courses: Application to Fuel Cell Fundamentals

Finite Element Modules for Enhancing Undergraduate Transport Courses: Application to Fuel Cell Fundamentals Finite Element Modules for Enhancing Undergraduate Transport Courses: Application to Fuel Cell Fundamentals Originally published in 2007 American Society for Engineering Education Conference Proceedings

More information

StarCCM+ Pipe Flow Tutorial

StarCCM+ Pipe Flow Tutorial 2/1/12 5:54:46 PM Star-CCM+ Pipe Flow Tutorial page: 1 I. Plan the Analysis A. Physical Model D V L 1. Laminar flow of air 2. Dimensions: D = 3 cm, L =? 3. Boundary conditions (a) Choose inlet velocity

More information

Computational Fluid Dynamics Analysis of airflow around a car model using Solidworks Flow Simulation

Computational Fluid Dynamics Analysis of airflow around a car model using Solidworks Flow Simulation Computational Fluid Dynamics Analysis of airflow around a car model using Solidworks Flow Simulation 1 Version 13.02.2015, 01:35 To display the CFD catalogue, click View in menu, and tick the Navigation

More information

Tutorial for laboratory project #2 Using ANSYS Workbench. For Double Pipe Heat Exchanger

Tutorial for laboratory project #2 Using ANSYS Workbench. For Double Pipe Heat Exchanger Tutorial for laboratory project #2 Using ANSYS Workbench For Double Pipe Heat Exchanger 1. Preparing ANSYS Workbench Go to Start Menu/All Programs/Simulation/ANSYS 12.1/Workbench. In the toolbox menu in

More information

Tutorial: Dam-Break Simulation Using FLUENT s Volume of Fluid Model

Tutorial: Dam-Break Simulation Using FLUENT s Volume of Fluid Model Tutorial: Dam-Break Simulation Using FLUENT s Volume of Fluid Model Purpose This tutorial examines the dam-break problem using the Volume of Fluid (VOF) multiphase model. This tutorial demonstrates how

More information

Introduction to ANSYS

Introduction to ANSYS Lecture 3 Introduction to ANSYS Meshing 14. 5 Release Introduction to ANSYS Meshing 2012 ANSYS, Inc. March 27, 2014 1 Release 14.5 Introduction to ANSYS Meshing What you will learn from this presentation

More information

Boundary Conditions. Introductory FLUENT Training ANSYS, Inc. All rights reserved. ANSYS, Inc. Proprietary

Boundary Conditions. Introductory FLUENT Training ANSYS, Inc. All rights reserved. ANSYS, Inc. Proprietary Boundary Conditions Introductory FLUENT Training 2006 ANSYS, Inc. All rights reserved. 2006 ANSYS, Inc. All rights reserved. 4-2 Defining Boundary Conditions To define a problem that results in a unique

More information

Cylinder Drag Coefficient

Cylinder Drag Coefficient 5 Cylinder Drag Coefficient COSMOSFloWorks can be used to study flow around objects and to determine the resulting aerodynamic lift and drag forces on the objects due to the flow. In this example we use

More information

City of Cranbrook. Cemetery Web Map User Guide

City of Cranbrook. Cemetery Web Map User Guide City of Cranbrook Cemetery Web Map User Guide 1 Table of Contents Using Cranbrook s Cemetery Web Map... 3 Navigating around the site... 3 Turning Map Layers On/Off... 3 Identify Tool... 4 How to Search

More information

Start the parallel version of FLUENTusing either Linux/UNIX, or Windows.

Start the parallel version of FLUENTusing either Linux/UNIX, or Windows. Tutorial 25. Parallel Processing Introduction This tutorial illustrates the setup and solution of a simple 3D problem using FLUENT s parallel processing capabilities. In order to be run in parallel, the

More information

NEW FEATURE OVERVIEW SPRINGCM S APPROVAL WORKFLOW TOOL (AKA ROUTING AND APPROVAL WORKFLOW)

NEW FEATURE OVERVIEW SPRINGCM S APPROVAL WORKFLOW TOOL (AKA ROUTING AND APPROVAL WORKFLOW) NEW FEATURE OVERVIEW SPRINGCM S APPROVAL WORKFLOW TOOL (AKA ROUTING AND APPROVAL WORKFLOW) SpringCM is deploying a new series of enhancements to the Approval workflow. Approval Workflows is a core platform

More information

Finding Drag Coefficient using Solidworks Flow Simulation

Finding Drag Coefficient using Solidworks Flow Simulation Finding Drag Coefficient using Solidworks Flow Simulation Using solidworks to find the drag coefficient of shapes is a very useful way to cut down on the design time of a project, as it can remove tests.

More information

MARKETING TOOLS. Creating a Marketing Campaign in Point:

MARKETING TOOLS. Creating a Marketing Campaign in Point: Point users can now market and grow business right from Point with a few clicks of the mouse. New tools allow Point users to create custom letters, newsletters, promotional emails, and mailing labels instantly

More information

FRACTURE MECHANICS IN ANSYS R16. Session 02 How to Perform Fracture Mechanics Analysis in Workbench

FRACTURE MECHANICS IN ANSYS R16. Session 02 How to Perform Fracture Mechanics Analysis in Workbench FRACTURE MECHANICS IN ANSYS R16 Session 02 How to Perform Fracture Mechanics Analysis in Workbench PERFORMING A FRACTURE ANALYSIS Fracture analysis requires that you define a crack. Since fracture parameter

More information

ABAQUS Tutorial. 3D Modeling

ABAQUS Tutorial. 3D Modeling Spring 2011 01/21/11 ABAQUS Tutorial 3D Modeling This exercise intends to demonstrate the steps you would follow in creating and analyzing a simple solid model using ABAQUS CAE. Introduction A solid undergoes

More information

Getting Started with ANSYS ANSYS Workbench Environment

Getting Started with ANSYS ANSYS Workbench Environment Getting Started with ANSYS ANSYS Workbench Environment Overview The purpose of this tutorial is to get you started with the ANSYS Workbench environment. We will use a simple, static analysis of a single

More information

Learning Module 4 - Thermal Fluid Analysis Note: LM4 is still in progress. This version contains only 3 tutorials.

Learning Module 4 - Thermal Fluid Analysis Note: LM4 is still in progress. This version contains only 3 tutorials. Learning Module 4 - Thermal Fluid Analysis Note: LM4 is still in progress. This version contains only 3 tutorials. Attachment C1. SolidWorks-Specific FEM Tutorial 1... 2 Attachment C2. SolidWorks-Specific

More information

Introduction to COMSOL. The Navier-Stokes Equations

Introduction to COMSOL. The Navier-Stokes Equations Flow Between Parallel Plates Modified from the COMSOL ChE Library module rev 10/13/08 Modified by Robert P. Hesketh, Chemical Engineering, Rowan University Fall 2008 Introduction to COMSOL The following

More information

Cylinder Drag Coefficient

Cylinder Drag Coefficient 5 Cylinder Drag Coefficient Flow Simulation can be used to study flow around objects and to determine the resulting lift and drag forces on the objects due to the flow. In this example we use Flow Simulation

More information

NUMERICAL ANALYSIS OF THERMAL PERFORMANCE OF LOUVER FIN

NUMERICAL ANALYSIS OF THERMAL PERFORMANCE OF LOUVER FIN NUMERICAL ANALYSIS OF THERMAL PERFORMANCE OF LOUVER FIN Deepak Hasurkar Department of Mechanical Engineering, Indira College of Engineering & Management, Pune Dr. Vinayak Kale Department of Mechanical

More information

Modeling External Compressible Flow

Modeling External Compressible Flow Tutorial 3. Modeling External Compressible Flow Introduction The purpose of this tutorial is to compute the turbulent flow past a transonic airfoil at a nonzero angle of attack. You will use the Spalart-Allmaras

More information

AUTOMOTIVE COMPUTATIONAL FLUID DYNAMICS SIMULATION OF A CAR USING ANSYS

AUTOMOTIVE COMPUTATIONAL FLUID DYNAMICS SIMULATION OF A CAR USING ANSYS International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 2, March-April 2016, pp. 91 104, Article ID: IJMET_07_02_013 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=2

More information

Titelmasterformat durch Klicken bearbeiten

Titelmasterformat durch Klicken bearbeiten Titelmasterformat durch Klicken bearbeiten ANSYS AIM Product simulation for every engineer Erke Wang CADFEM GmbH Georg Scheuerer ANSYS Germany GmbH Christof Gebhardt CADFEM GmbH All products involve multiple

More information

ANSYS Thermoelectric Generator (TEG) Tutorial

ANSYS Thermoelectric Generator (TEG) Tutorial ANSYS Thermoelectric Generator (TEG) Tutorial Preparing the ANSYS Workbench 1) Go Start Menu All Programs Simulation ANSYS 12.1 Workbench 2) In the toolbox menu on the left portion of the window, double

More information

Abaqus CAE (ver. 6.12) Impact tutorial

Abaqus CAE (ver. 6.12) Impact tutorial Abaqus CAE (ver. 6.12) Impact tutorial Problem Description An aluminum part is dropped onto a rigid surface. The objective is to investigate the stress and deformations during the impact. 2013 Hormoz Zareh

More information

The Navier-Stokes Equations

The Navier-Stokes Equations Flow Between Parallel Plates Modified from the COMSOL ChE Library module. Modified by Robert P. Hesketh, Chemical Engineering, Rowan University Fall 2007 The Navier-Stokes Equations The Navier-Stokes equations

More information

Lecture 11 Results and Post Processing

Lecture 11 Results and Post Processing Lecture 11 Results and Post Processing 16.0 Release Introduction to ANSYS Mechanical 1 2015 ANSYS, Inc. February 27, 2015 Chapter Overview In this chapter controlling the display of results and the detection

More information

Finite Element Analysis (FEA) Tutorial. Project 2: 2D Plate with a Hole Problem

Finite Element Analysis (FEA) Tutorial. Project 2: 2D Plate with a Hole Problem Finite Element Analysis (FEA) Tutorial Project 2: 2D Plate with a Hole Problem Problem Analyze the following plate with hole using FEA tool ABAQUS P w d P Dimensions: t = 3 mm w = 50 mm d = mm L = 0 mm

More information

Enable the Epilogue Author Add-in

Enable the Epilogue Author Add-in 1. The File Tab in MS Word Image: The user sees the File Tab in the upper left corner of the MS Word screen. Instruction: Click the File Tab button. 2. The Options link in Back Office Image: The user sees

More information

Tutorial for laboratory project #1. Using ANSYS Workbench. For Thermal Behavior of an Electrical Wire

Tutorial for laboratory project #1. Using ANSYS Workbench. For Thermal Behavior of an Electrical Wire Tutorial for laboratory project #1 Using ANSYS Workbench For Thermal Behavior of an Electrical Wire 1. Preparing ANSYS Workbench Go to Start Menu/All Programs/ANSYS 12.1/Workbench In the toolbox menu in

More information

ST Resorts Template for SobiPro Installation & Setup Guide

ST Resorts Template for SobiPro Installation & Setup Guide Website: http://www.sobitemplates.com Support: http://www.sobitemplates.com/forum ST Resorts Template for SobiPro Installation & Setup Guide Overview: The ST Resorts Template for SobiPro has a lot of features

More information

Getting Started / Tutorials

Getting Started / Tutorials High-performance EM simulation software Technological leadership since 1992 Complete Technology for 3D EM 260 employees Worldwide support network Getting Started / Tutorials The introductory books are

More information

UW- Green Bay QuickBooks Accounts Receivable User Manual

UW- Green Bay QuickBooks Accounts Receivable User Manual UW- Green Bay QuickBooks Accounts Receivable User Manual Table of Contents Topic Page Number Logging into QuickBooks 2 Changing your password. 3 Creating Invoices. 4 Customer Entry/Search. 5-7 Entering

More information

Scaling New Heights in Aerodynamics Optimization: The 50:50:50 Method

Scaling New Heights in Aerodynamics Optimization: The 50:50:50 Method White Paper Scaling New Heights in Aerodynamics Optimization: By Ashok Khondge Lead Technology Specialist and Sandeep Sovani, Ph. D. Manager of Global Automotive Strategy ANSYS, Inc. Aerodynamics development

More information

Dynamic Analysis of Machine Foundation

Dynamic Analysis of Machine Foundation Dynamic Analysis of Machine Foundation 35-1 Dynamic Analysis of Machine Foundation In this tutorial, RS2 is used to simulate a foundation experiencing cyclic machine loading. This tutorial covers the basics

More information

T&B CAD Library Help Guide

T&B CAD Library Help Guide 2-D and 3-D CAD Models for over 2,300 electrical conduit and fittings products The T&B CAD Library allows you to view and/or download CAD models in a variety of 2-D and 3-D formats to meet virtually any

More information

Lab#2 Mohr s Circle and state of stress By C. Daley

Lab#2 Mohr s Circle and state of stress By C. Daley Engineering 5003 - Ship Structures I Lab#2 Mohr s Circle and state of stress By C. Daley Overview Consider a steel plate subject to some type of in-plane loading, for example as in the case in lab#1. Any

More information

Introduction to ANSYS ICEM CFD

Introduction to ANSYS ICEM CFD Workshop 8.2 3D Pipe Junction 14.5 Release Introduction to ANSYS ICEM CFD 2012 ANSYS, Inc. April 1, 2013 1 Release 14.5 3D Pipe Junction 3D Pipe Junction This is a simple 4-way pipe intersection with two

More information

ANSYS CFX Tutorial Laminar Flow in a Rectangular Duct 22 January 2013 V4.00. ANSYS CFX Tutorial. Scott J. Ormiston Jeffrey R. Berg

ANSYS CFX Tutorial Laminar Flow in a Rectangular Duct 22 January 2013 V4.00. ANSYS CFX Tutorial. Scott J. Ormiston Jeffrey R. Berg ANSYS CFX Tutorial Laminar Flow in a Rectangular Duct Scott J. Ormiston Jeffrey R. Berg Department of Mechanical Engineering Winnipeg, Manitoba Canada V4.00 22 January 2013 Department of Mechanical Engineering

More information

Modeling Radiation and Natural Convection

Modeling Radiation and Natural Convection Tutorial 5. Modeling Radiation and Natural Convection Introduction In this tutorial combined radiation and natural convection are solved in a three-dimensional square box on a mesh consisting of hexahedral

More information

A Guide to the free mesh program Discretizer with OpenFOAM for CFD (Computational Fluid Dynamics)

A Guide to the free mesh program Discretizer with OpenFOAM for CFD (Computational Fluid Dynamics) Discretizer Manual Release date 09/01/10 Side 1 of 13 A Guide to the free mesh program Discretizer with OpenFOAM for CFD (Computational Fluid Dynamics) Homepage: http://www.discretizer.org/ Creator of

More information

Starting a WordPress Site

Starting a WordPress Site Starting a WordPress Site Navigate to www.wordpress.com Click on Get started here. Choose a name for your website You have a couple options here. You can choose a site name that ends in "wordpress.com"

More information

. Address the following issues in your solution:

. Address the following issues in your solution: CM 3110 COMSOL INSTRUCTIONS Faith Morrison and Maria Tafur Department of Chemical Engineering Michigan Technological University, Houghton, MI USA 22 November 2012 Zhichao Wang edits 21 November 2013 revised

More information

Email Address Collector. - Tutorial -

Email Address Collector. - Tutorial - Email Address Collector - Tutorial - How to extract email addresses from mail folders 1. Open Email Address Collector Once the product is installed and your license is activated, you can start extracting

More information

Lab#3 ANSYS Analysis of a Beam By Claude Daley 2012

Lab#3 ANSYS Analysis of a Beam By Claude Daley 2012 Engineering 5003 - Ship Structures I Lab#3 ANSYS Analysis of a Beam By Claude Daley 2012 INTRODUCTION A 10.0 m long rectangular beam carries a patch load of 5 N/m (excluding its own weight) as shown below.

More information

ANSYS FLUENT. Electronics Cooling with Natural Convection and Radiation WS4-1. Customer Training Material

ANSYS FLUENT. Electronics Cooling with Natural Convection and Radiation WS4-1. Customer Training Material Workshop 4 Electronics Cooling with Natural Convection and Radiation Introduction to ANSYS FLUENT WS4-1 Goals In this workshop, you will model the heat dissipation from a hot electronics component fitted

More information

INTRODUCTION TO FINITE ELEMENT ANALYSIS USING MSC.PATRAN/NASTRAN

INTRODUCTION TO FINITE ELEMENT ANALYSIS USING MSC.PATRAN/NASTRAN Objective INTRODUCTION TO FINITE ELEMENT ANALYSIS USING MSC.PATRAN/NASTRAN The goal of this exercise is to prepare a finite element model using surface representation of an object from CAD system. Then

More information

itrack Intergen s Defect Management System

itrack Intergen s Defect Management System itrack Intergen s Defect Management System itrack Quick Reference Guide Version 2.0 Copyright 2009 Intergen Limited Table of Contents 1 INTRODUCTION... 3 2 GETTING STARTED... 3 2.1 Logon... 3 2.2 Select

More information

CFD Analysis and Optimization of a Car Spoiler

CFD Analysis and Optimization of a Car Spoiler International Journal of Mechanical Engineering and Research, ISSN 0973-4562 Vol. 5 No.1 (2015) CFD Analysis and Optimization of a Car Spoiler C.V.Karthick Bala Murugan 1, P.A.Nigal Ashik 2, P.Raju 3 Assistant

More information

Laminar Flow in a Baffled Stirred Mixer

Laminar Flow in a Baffled Stirred Mixer Laminar Flow in a Baffled Stirred Mixer Introduction This exercise exemplifies the use of the rotating machinery feature in the CFD Module. The Rotating Machinery interface allows you to model moving rotating

More information

EXTERNAL AERODYNAMICS: FLOW OVER A CAR. Source: Automotive Engineering

EXTERNAL AERODYNAMICS: FLOW OVER A CAR. Source: Automotive Engineering EXTERNAL AERODYNAMICS: FLOW OVER A CAR Source: Automotive Engineering OBJECTIVE OF AERODYNAMIC CALCULATIONS To compute & visualize velocity and pressure contour over car body surfaces To Predict Aerodynamic

More information

Flow Past a Circular Cylinder

Flow Past a Circular Cylinder Tutorial 6. Flow Past a Circular Cylinder Introduction The purpose of this tutorial is to illustrate the setup and solution of an unsteady flow past a circular cylinder and to study the vortex shedding

More information

ANSYS Maxwell V16 Training Manual

ANSYS Maxwell V16 Training Manual Lecture 4: Static Electric Solvers ANSYS Maxwell V16 Training Manual 2013 ANSYS, Inc. May 21, 2013 1 Release 14.5 Content A. Electrostatic Solver a. Selecting the Electrostatic Solver b. Material Definition

More information

MICROSOFT OUTLOOK 2010 WORK WITH CONTACTS

MICROSOFT OUTLOOK 2010 WORK WITH CONTACTS MICROSOFT OUTLOOK 2010 WORK WITH CONTACTS Last Edited: 2012-07-09 1 Access to Outlook contacts area... 4 Manage Outlook contacts view... 5 Change the view of Contacts area... 5 Business Cards view... 6

More information

Process Document Campus Community: Create Communication Template. Document Generation Date 7/8/2009 Last Changed by Status

Process Document Campus Community: Create Communication Template. Document Generation Date 7/8/2009 Last Changed by Status Document Generation Date 7/8/2009 Last Changed by Status Final System Office Create Communication Template Concept If you frequently send the same Message Center communication to selected students, you

More information

Workflow Example Horn Antenna

Workflow Example Horn Antenna Workflow Example Horn Antenna Purpose : Optimize the aperture of the horn antenna such that the gain is maximized at 10 GHz. 1 CST MWS - Standard Workflow Choose a project template. Create your model.

More information

Tutorial: From TexGen to Finite Element Analysis

Tutorial: From TexGen to Finite Element Analysis Tutorial: From TexGen to Finite Element Analysis Xuesen Zeng Division of Materials, Mechanics & Structures Faculty of Engineering University of Nottingham University Park Nottingham UK 2 May, 2012 1 TexGen

More information

Creating a PowerPoint Presentation

Creating a PowerPoint Presentation Creating a PowerPoint Presentation Getting Started 1. Open PowerPoint from the "Start" "Programs" Microsoft Office directory. 2. When starting PowerPoint, it usually starts with a new blank presentation.

More information

How Analyze a STL File

How Analyze a STL File How Analyze a STL File Stallion 3D accepts STL files saved in the ASCII format. Ideally, we recommend files that contain about 20,000 facets. Larger files will results in longer pre-processing times. 1.

More information

ANSYS Maxwell V16 Training Manual

ANSYS Maxwell V16 Training Manual Lecture 3: Static Magnetic Solvers ANSYS Maxwell V16 Training Manual 2013 ANSYS, Inc. May 21, 2013 1 Release 14.5 Content A. Magnetostatic Solver a. Selecting the Magnetostatic Solver b. Material Definition

More information

PUTTING THE SPIN IN CFD

PUTTING THE SPIN IN CFD W H I T E PA P E R PUTTING THE SPIN IN CFD Overview Engineers who design equipment with rotating components need to analyze and understand the behavior of those components if they want to improve performance.

More information

Embankment Consolidation

Embankment Consolidation Embankment Consolidation 36-1 Embankment Consolidation In this tutorial, RS2 is used for a coupled analysis of a road embankment subject to loading from typical daily traffic. Model Start the RS2 9.0 Model

More information

Comsol Tutorial: Laminar Flow Reactor with Heat Transfer Effects Spring 2007

Comsol Tutorial: Laminar Flow Reactor with Heat Transfer Effects Spring 2007 Comsol Tutorial: Laminar Flow Reactor with Heat Transfer Effects Spring 2007 Objectives: 1) Describe to a graduate student the difference between the prediction of the outlet conversion obtained from a

More information

Microsoft outlook plug-in for kpi.com

Microsoft outlook plug-in for kpi.com Microsoft outlook plug-in for kpi.com Contents Installation... 3 Requirements... 3 Installing... 3 Synchronization... 3 Manual Synchronization... 3 How to manually start synchronization?... 4 Contact synchronization...

More information