XCP The way forward. Mohamad Sah, Vector Informatik India V
|
|
- Harvey Andrews
- 7 years ago
- Views:
Transcription
1 XCP The way forward Mohamad Sah, Vector Informatik India V
2 Agenda What? How? Who? XCP Where? When? Why? 2
3 What? What is XCP? Temp Press RAM 0x5000 Temp 0x5004 Press DAQ 0 ODT 0 ODT 1 ODT 2 DAQ 1 ODT 0 ODT 1 ECU XCP Signifies Universal Measurement & Calibration Protocol". X stands for the variable and interchangeable transport layer. The measurement signals are transmitted over a serial network like CAN, LIN, FlexRay or Ethernet. XCP works on master-slave architecture. Flash Application The primary applications of XCP are measurement and calibration of internal ECU parameters. XCP is the successor of CCP. The current version of XCP is 1.3. XCP CCP Diag MCD Tool CAN driver CAN Controller CAN Interface EEPROM CAN Transceiver CAN 3
4 Who? Who defines and maintains the standard? Association for Standardisation of Automation and Measuring Systems (ASAM e.v.) Founded in 1998 by the European automotive manufacturers and suppliers. Among the members are: Automotive manufacturers: Audi AG, BMW AG, Daimler AG, GM General Motors Corporation, MAN Nutzfahrzeuge AG, Porsche AG, Renault SA, Volkswagen AG, Volvo Technological Dev. Corp. Supplier companies: AFT Atlas Fahrzeugtechnik GmbH, AVL GmbH, Drecq Daniel Technologies, DENSO Corporation, dspace GmbH, ETAS GmbH, FEV Motorentechnik GmbH, Ipetronik GmbH, Robert Bosch GmbH, Siemens AG A&D PT3, VDO Automotive AG, Vector Informatik 4
5 Who? ASAM interface model Higher level automation system ASAM MCD 3 MC CANape CCP / XCP driver ASAM MCD 1 MC ASAM MCD 2 MC *.a2l ECU Measurement and Calibration Data Exchange Format CCP / XCP driver ECU 5
6 When? When XCP was introduced? ECU ECU as of 1992 CCP Protocol CAN bus CANape as of 2003 XCP Protocol CAN bus FlexRay bus Ethernet ECU ECU 6
7 Why? Difference between CCP & XCP Features XCP CCP Read/write accesses to device memory Calibration data page initialization/switching Synchronous data acquisition Flash programming Scalability Cold start measurement (Resume mode) Better resource utilization in the ECU (Dynamic DAQ List) 7
8 Why? Difference between CCP & XCP Features XCP CCP Automatic detection of slaves Synchronous data stimulation (bypassing) Optimized communication by block transfer Precise measurement data acquisition by measuring time stamps in the ECU 8
9 Why? Basic Features of XCP Synchronous data acquisition/stimulation Read/write accesses to device memory Calibration data page initialization/switching Flash programming 9
10 Why? Extended Features of XCP Automatic detection and configuration of Slaves Block Transfer Mode for upload, download and flashing Dynamic DAQ lists configuration Acquisition of measured data with time stamps Synchronized and prioritized data transfer Power-up data transfer Download of flash programming routines 10
11 Why? Benefits of XCP Reduced CAN bandwidth Tool and Vendor Independent Communication platform Block Transfers reduce download and upload time Significantly stronger security protection First loop data acquisition possible Improved measurement synchronization Small scalable code for any bandwidth Usable for every purpose : from function development and modeling to production car application 11
12 Why? Benefits of XCP With Vector VX Interface, the users do not even need the XCP driver for measurement and calibration applications since the driver is already integrated in Standard Debug / Trace Ports: - JTAG / DAP(2) AUDII/ DigRF - RTP / NEXUS / AURORA ECU Plug On Device Automotive qualified: - High Speed Cable XCPonEthernet Measurment Max 7.5 m Base Module Standard ASAM Interface & Calibration Tool 12
13 Why? Vector s XCP Credentials Vector offer the most sophisticated XCP Master tool (CANape) and XCP source code in the market since XCP Professional Driver: Purchased by over 100 global OEMs & Suppliers to date Solid code base with high level of maturity Leverage the enormous amount of validation testing already completed Offers high value solution 13
14 Where? Model in the Loop Both controller and plants are simulated as a model. Both models run in Simulink as runtime environment to analyze the behavior. Measurement and Calibration capabilities can be realized by integrating an XCP slave. No code generation or instrumentation of the model is necessary. 14
15 Where? Software in the Loop Code generated from the model and the model is runing in PC based environment as a DLL. Using XCP the model can be calibrated. 15
16 Where? Hardware in the Loop Algorithm runs in a microcontroller platform while the plant continues to be simulated. The user has access to the algorithm in the ECU over XCP. 16
17 Where? Rapid Control Prototyping Algorithm runs on a real time hardware instead of an real ECU. Integration of XCP helps in settings up an OEM independent tool chain. Helps in quickly develop a functional prototype. 17
18 How? XCP Implementation Vector provides free Basic driver for XCP. Available for free download at with documents on how to implement it in your ECU. Also available is a free XCP ebook for download. 18
19 How? XCP Implementation Still need help? Please write to or 19
20 For more information about Vector and our products please visit Author: Mohamad Sah Vector Informatik India Vector Informatik India Private Limited. All rights reserved. Any distribution or copying is subject to prior written approval by Vector. V
Product Information CANape Option Simulink XCP Server
Product Information CANape Option Simulink XCP Server Table of Contents 1 Overview... 3 1.1 Introduction... 3 1.2 Overview of Advantages... 3 1.3 Application Areas... 3 1.4 Further Information... 4 2 Functions...
More informationAutomatic ASAM MCD-3 supported test. PikeTec GmbH Dr. Jens Lüdemann
Automatic ASAM MCD-3 supported test PikeTec GmbH Dr. Jens Lüdemann Test challenges Clear test case description (Modeling) Continuity and consistency at all test platforms Automated Execution, Assessment,
More informationStandardized software components will help in mastering the. software should be developed for FlexRay were presented at
Embedded Software for FlexRay Systems Special aspects and benefits of implementing modularized software Standardized software components will help in mastering the growing complexity of the interplay of
More informationProduct Information CANape
Product Information CANape Table of Contents 1 Overview... 3 1.1 Introduction... 3 1.2 Overview of Advantages... 3 1.3 Application Areas... 4 1.4 Features... 4 1.5 System Requirements... 4 1.6 Supported
More informationBeschleunigen Sie die Entwicklung Ihrer Embedded Software mit Dienstleistungen von Vector
Beschleunigen Sie die Entwicklung Ihrer Embedded Software mit Dienstleistungen von Vector Vector Embedded Software 2013 V1.3.0 2013-04-04 Your Presenters Today Michael Buck Manager Product Services / Technical
More informationEHOOKS Prototyping is Rapid Again
09CV-0113 EHOOKS Prototyping is Rapid Again Vivek Jaikamal ETAS Inc. Nigel Tracey ETAS Ltd. Copyright 2009 SAE International ABSTRACT Automotive controls engineers have traditionally used bypass rapid
More informationIntroduction to the CAN Calibration Protocol Version 3.0 2004-05-04 Application Note AN-AMC-1-102
Version 3.0 2004-05-04 Restrictions Abstract Public Document This application note introduces the CAN Calibration Protocol used to calibrate controllers during module development. The paper also discusses
More informationHerstellerinitiative Software (OEM Initiative Software)
Herstellerinitiative Software (OEM Initiative Software) Dr. Michael Daginnus Volkswagen AG Wolfsburg Dr. Dieter Marx Porsche AG Weissach Dr. Ralf Belschner Daimler AG Sindelfingen Kai Barbehön BMW AG München
More informationModel-Based Development of ECUs
Model-Based Development of ECUs Software Simulation with MATLAB/Simulink and CANoe MATLAB/Simulink is a tool that is widely used in many engineering and scientific disciplines. In the automotive field,
More informationConfiguration management in AUTOSAR
Configuration management in AUTOSAR The need for efficient process tools for Automotive System Engineering V0.01 2008-11-02 Introduction AUTOSAR will influence the ECU SW Architecture and also the way
More informationDevelopment of AUTOSAR Software Components within Model-Based Design
2008-01-0383 Development of AUTOSAR Software Components within Model-Based Design Copyright 2008 The MathWorks, Inc. Guido Sandmann Automotive Marketing Manager, EMEA The MathWorks Richard Thompson Senior
More informationXCP The Standard Protocol for ECU Development Fundamentals and Application Areas
XCP The Standard Protocol for ECU Development Fundamentals and Application Areas Andreas Patzer Rainer Zaiser Andreas Patzer Rainer Zaiser XCP The Standard Protocol for ECU Development Date April 2013
More informationChip simulation of automotive ECUs
Chip simulation of automotive ECUs Jakob Mauss, QTronic GmbH Matthias Simons, Daimler AG 9. Symposium Steuerungssysteme für automobile Antriebe Berlin-Tempelhof, 20.-21.09.2012 Outline of the talk Chip
More informationPlug and Play Solution for AUTOSAR Software Components
Plug and Play Solution for AUTOSAR Software Components The interfaces defined in the AUTOSAR standard enable an easier assembly of the ECU application out of components from different suppliers. However,
More informationIn networking ECUs in heavy-duty vehicles, it is the J1939 protocol that. plays a key role. J1939 networks are based on the CAN bus (high-speed
Networking Heavy-Duty Vehicles Based on SAE J1939 From Parameter Group to plug-and-play Application In networking ECUs in heavy-duty vehicles, it is the J1939 protocol that plays a key role. J1939 networks
More informationAutomatic Validation of Diagnostic Services
Development ProcessES Diagnostics Automatic Validation of Diagnostic Services For the first time, a fully automated test case generator has been introduced in diagnostics validation at General Motors Europe
More informationEmbedded OS. Product Information
Product Information Table of Contents 1 Operating Systems for ECUs... 3 2 MICROSAR.OS The Real-Time Operating System for the AUTOSAR Standard... 3 2.1 Overview of Advantages... 3 2.2 Properties... 4 2.3
More informationopenmdm an Open Source Platform for Measured Data Management Dr. Dietmar Rapf, Michael Schwarzbach
openmdm an Open Source Platform for Measured Data Management Dr. Dietmar Rapf, Michael Schwarzbach Agenda History and Scope of measured data management ASAM ODS the basis for MDM systems openmdm How openmdm
More informationINCA V7.2 New functions
INCA V7.2 New functions At a Glance Acquisition of tens of thousands of signals from the ECU at high cycle rates by means of the new FETK interface Connection to several FETK ECUs plus CAN, CAN FD, LIN,
More informationCANape CCP Communication Version 1.1 02/06/03 Application Note AN-AMC-1-100
Version 1.1 02/06/03 Application Note AN-AMC-1-100 Author(s) Restrictions Abstract Kim Lemon Public Document This application note concentrates on explaining the fundamental concepts about CANape and CCP
More informationBUSMASTER An Open Source Tool
BUSMASTER An Open Source Tool Dr. Tobias Lorenz, ETAS GmbH Presented by Dr. Andrew Borg In August, ETAS and Robert Bosch Engineering and Business Solutions (RBEI) jointly published BUSMASTER, a free open
More informationIntroduction to Higher-Level Protocols Version 1.0 Application Note AN-AND-1-160
Version 1.0 Application Note AN-AND-1-160 Restrictions Abstract Public Document This application notes gives an overview of the major features of the most widely used high-level protocols in the automotive
More informationProduct Information Services for Embedded Software
Product Information Services for Embedded Software Table of Contents 1 Technical Consulting/Engineering Services... 3 1.1 Overview of Advantages... 3 1.2 Application Areas... 3 2 Product- Services - Proficient
More informationUsing big data in automotive engineering?
Using big data in automotive engineering? ETAS GmbH Borsigstraße 14 70469 Stuttgart, Germany Phone +49 711 3423-2240 Commentary by Friedhelm Pickhard, Chairman of the ETAS Board of Management, translated
More informationIntroduction to Ethernet and IP in automotive vehicles
Introduction to Ethernet and IP in automotive vehicles Webinar V1.02 2014-05-14 Agenda > Information 3 Introduction 6 Physical layers 8 IEEE Ethernet MAC + VLAN 14 Internet Protocol (IPv4/IPv6) 18 TCP
More informationAutomotive Ethernet Prototype and test development with CANoe/CANalyzer.Ethernet
Insert picture and click Align Title Graphic. Automotive Ethernet Prototype and test development with CANoe/CANalyzer.Ethernet Vector Webinar 2014 Hans-Werner Schaal Ver. 4.2.1, Jun 2014 Slide: 1 Agenda
More informationUser-friendly Configuration of AUTOSAR ECUs with Specialized Software Tools
User-friendly Configuration of AUTOSAR ECUs with Specialized Software Tools The simple CAN ECU is a thing of the past. Now, a typical ECU utilizes many functions of the AUTOSAR basic software to perform
More informationSoftware Development for Multiple OEMs Using Tool Configured Middleware for CAN Communication
01PC-422 Software Development for Multiple OEMs Using Tool Configured Middleware for CAN Communication Pascal Jost IAS, University of Stuttgart, Germany Stephan Hoffmann Vector CANtech Inc., USA Copyright
More informationCollaborating in California: Open HIL Test System Architecture uses the ASAM HIL API
Collaborating in California: Open HIL Test System Architecture uses the ASAM HIL API ASAM INTERNATIONAL CONFERENCE, Dec. 03 04, 2013, Dresden, Germany Dr. Jiri Keprt, National Instruments Corporation (Speaker)
More informationLIN (Local Interconnect Network):
LIN (Local Interconnect Network): History: LIN (Local Interconnect Network) was developed as cost-effective alternate to CAN protocol. In 1998 a group of companies including Volvo, Motorola, Audi, BMW,
More informationwww.imprezer.tk Introduction to www.union88.tk RACE FUELS Hans-Christian von der Wense Munich, Germany
Introduction to Hans-Christian von der Wense Munich, Germany Overview Progress in Automotive Electronics and it s Impacts on Networking LIN Consortium LIN Concept Physical Layer Data Link Layer LIN Network
More informationFrom Signal Routing to complete AUTOSAR compliant CAN design with PREEvision (II)
From Signal Routing to complete AUTOSAR compliant CAN design with PREEvision (II) RELEASED V0.01 2014-12-02 Agenda PREEvision AUTOSAR Webinar Part I AUTOSAR System and Software Design with PREEvision The
More informationChallenge of Ethernet Use in the Automobile
Challenge of Ethernet Use in the Automobile Flexible interfaces and software tools simplify ECU development Already this year, Ethernet will be used as a system network in the first production vehicles.
More informationopenmdm an Open Source Platform for Measured Data Management Dr. Dietmar Rapf, Michael Schwarzbach
openmdm an Open Source Platform for Measured Data Management Dr. Dietmar Rapf, Michael Schwarzbach openmdm an Open Source Platform for Measured Data Management Seite 2 IT and PLM consulting business since
More informationAutomotive Software Development Challenges Virtualisation and Embedded Security
Automotive Software Development Challenges Virtualisation and Embedded Security 1 Public ETAS-PGA/PRM-E October 2014 ETAS GmbH 2014. All rights reserved, also regarding any disposal, exploitation, Automotive
More informationProduct Information CANdelaStudio
Table of Contents 1 Introduction... 3 1.1 Properties Overview... 3 2 Functions... 4 3 ODX-Functions... 6 4 Quality Improvement by Single Source Principle... 6 5 Data Exchange... 7 6 Editions... 7 6.1 CANdelaStudio
More informationEBERSPÄCHER ELECTRONICS automotive bus systems. solutions for network analysis
EBERSPÄCHER ELECTRONICS automotive bus systems solutions for network analysis DRIVING THE MOBILITY OF TOMORROW 2 AUTOmotive bus systems System Overview Analyzing Networks in all Development Phases Control
More informationidas Data Application and Documentation
idas Data Application and Documentation intelligent Data Application System Rainer Röhrle ZF Friedrichshafen AG TEN_1001_2_en Application Process (commercial vehicles) Offline calibration (pre calibration)
More informationProgramming Flash Microcontrollers through the Controller Area Network (CAN) Interface
Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Application te Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Abstract This
More informationTraining @ ETAS. We offer regularly scheduled training seminars for both novice and advanced ETAS tool users.
Training @ ETAS At ETAS we believe in training as an important aid to our customers to achieve maximum benefit of our tools and solutions in their projects. We strive to provide the highest possible quality
More informationProduct Information CANalyzer.J1939
Product Information CANalyzer.J1939 Table of Contents 1 Introduction... 3 1.1 Application Areas... 3 1.2 Features and Advantages... 3 1.3 Further Information... 3 2 Functions... 4 3 Hardware Interfaces...
More informationASCET in ECU Development Tool Chains
ASCET in ECU Development Tool Chains 1 From Function to Software Development Rapid Prototyping Modeling & Simulation Meas. & Calibr. INCA-EIP Meas. & Calibr. INCA Realtime Operation ES910 Virtual, & Rapid
More informationECU State Manager Module Development and Design for Automotive Platform Software Based on AUTOSAR 4.0
ECU State Manager Module Development and Design for Automotive Platform Software Based on AUTOSAR 4.0 Dhanamjayan P.R. 1, Kuruvilla Jose 2, Manjusree S. 3 1 PG Scholar, Embedded Systems, 2 Specialist,
More informationCycurHSM An Automotive-qualified Software Stack for Hardware Security Modules
CycurHSM An Automotive-qualified Software Stack for Hardware Security Modules Dr. Frederic Stumpf, ESCRYPT GmbH Embedded Security, Stuttgart, Germany 1 Introduction Electronic Control Units (ECU) are embedded
More informationArbeitskreis zur Standardisierung von Applikationssystemen Standardization of Application/Calibration Systems task force
ASAP Standard CCP CAN Calibration Protocol Version 2.1 Version 2.1 Date 18. February 1999 Status Release Author H. Kleinknecht Distribution public Co-Authors V2.1: Andreas Krüger Hewlett Packard Hans-Georg
More informationCar2x From Research to Product Development
Car2x From Research to Product Development How automotive OEMs and suppliers are successfully completing production Car2x projects Car2x systems present entirely new challenges for managers in product
More informationFord Motor Company. Automotive and transportation. $100+ million in warranty cost savings
Automotive and transportation $100+ million in warranty cost savings Product Teamcenter Business initiatives New product development Systems engineering and mechatronics Business challenges Minimize warranty
More informationMODEL-BASED DEVELOPMENT OF AUTOMOTIVE EMBEDDED SOFTWARE IN COMPLIANCE WITH ISO 26262: CHALLENGES & EFFECTIVE SOLUTIONS 8 JUNE - 9 JUNE 2015
MODEL-BASED DEVELOPMENT OF AUTOMOTIVE EMBEDDED SOFTWARE IN COMPLIANCE WITH ISO 26262: CHALLENGES & EFFECTIVE SOLUTIONS 8 JUNE - 9 JUNE 2015 Highlights Developing safety-critical software in compliance
More informationOne common language for domain experts and test engineers
One common language for domain experts and test engineers Cost-effective creation and reuse of test sequences with Vector s Test Automation Editor V0.01 2011-04-13 Agenda > Overview Introduction to the
More informationAUTOSAR Configuration Process - How to handle 1000s of parameters
AUTOSAR Configuration Process - How to handle 1000s of parameters Webinar 2013-04-19 V2.0 2013-04-18 Agenda >Introduction AUTOSAR ECU Configuration Description ECU Configuration Workflow Multi-User Workflow
More informationautomotive.elektrobit.com Driver assistance software EB Assist solutions
automotive.elektrobit.com Driver assistance software EB Assist solutions From driver assistance systems to automated driving Automated driving leads to more comfortable driving and makes the road safer
More informationSelection Criteria for ZigBee Development Kits
Selection Criteria for ZigBee Development Kits This article gives an overview about different considerations, when it comes to prioritizing ZigBee Development Kits, supplied by different vendors. Before
More informationSafety compliance. Energy management. System architecture advisory services. Diagnostics. Network topologies. Physical and functional partitioning
Energy management Network topologies Physical and functional partitioning Safety compliance Diagnostics System architecture advisory services www.continental-corporation.com Why system architecture? 2
More informationFrom Diagnostic Requirements to Communication
From Diagnostic Requirements to Communication Standardization is the Trend in the Development of Automotive Electronics A key aim of open architectures, configurable components and harmonized exchange
More informationAutomotive Software Engineering
Automotive Software Engineering List of Chapters: 1. Introduction and Overview 1.1 The Driver Vehicle Environment System 1.1.1 Design and Method of Operation of Vehicle Electronic 1.1.2 Electronic of the
More informationHirschmann Networking Interoperability in a
Automation and Network Solutions Hirschmann Networking Interoperability in a PROFInet Environment Hirschmann Interoperability White Paper Rev. 1.1 Contents Hirschmann Networking Interoperability in a Profinet
More informationimc BUSDAQ autonomous intelligent synchronized Field bus data acquisition - from stationary to mobile imc productive testing
imc BUSDAQ autonomous intelligent synchronized Field bus data acquisition - from stationary to mobile imc productive testing www.imc-berlin.com/busdaq imc BUSDAQ/BUSLOG at a glance Processes multiple networks
More informationTiming Analysis for Verification of Network Architectures. Timing Analysis
for Verification of Network Architectures In order to evaluate EE architectures regarding their timing and resource requirements, the knowledge of the required attributes and properties plays an important
More informationSmart Testing of Smart Charging
Smart Testing of Smart Charging Consistent test case coverage for electric mobility With the increasing diversity of electric vehicles and charging station systems, interoperability between components
More informationWhat is LOG Storm and what is it useful for?
What is LOG Storm and what is it useful for? LOG Storm is a high-speed digital data logger used for recording and analyzing the activity from embedded electronic systems digital bus and data lines. It
More informationOn the Way to Industrie 4.0 The Digital Enterprise Siemens AG 2015 siemens.com
Klaus Helmrich Member of the Managing Board of Siemens AG On the Way to Industrie 4.0 The Digital Enterprise siemens.com Siemens focuses on electrification, automation and digitalization and is actively
More informationOSI Layers in Automotive Networks
OSI Layers in Automotive Networks 2013-03-20 IEEE 802.1 Plenary Meeting - Orlando Aboubacar Diarra, Robert Bosch GmbH 1 Outline OSI Reference Model Simplified generic Architecture for Automotive Serial
More informationSubstation Automation Systems. Nicholas Honeth (nicholash@ics.kth.se)
Substation Automation Systems Nicholas Honeth (nicholash@ics.kth.se) Contents of the series Lecture 5 - Introduction to SAS - Nice creative exercise Lecture 6 - A bit about information modelling - Data
More informationgimm Global Integrated Manufacturing Manager. Solution for industrial management of productive and logistic factory processes
gimm Global Integrated Manufacturing Manager. Solution for industrial management of productive and logistic factory processes Solution for industrial management of productive and logistic factory processes
More informationEmbedded Ethernet Interface Using Arm Processor
IOSR Journal of Electronics and Communication Engineering (IOSR-JECE) ISSN: 2278-2834, ISBN: 2278-8735. Volume 4, Issue 4 (Jan. - Feb. 2013), PP 24-28 Embedded Ethernet Interface Using Arm Processor Raghava
More informationBMW Car IT GmbH. AUTOSAR - First Experiences and the Migration Strategy of the BMW Group
BMW Car IT GmbH. - First Experiences and the Migration Strategy of the BMW Group Dr. Christian, BMW Car IT Page 2 - First Experiences. Overview. 1. Focus of this talk: Model based development under the
More informationEB Automotive Driver Assistance EB Assist Solutions. Damian Barnett Director Automotive Software June 5, 2015
EB Automotive Driver Assistance EB Assist Solutions Damian Barnett Director Automotive Software June 5, 2015 Advanced driver assistance systems Market growth The Growth of ADAS is predicted to be about
More informationISO11783 a Standardized Tractor Implement Interface
ISO a ized Tractor Implement Interface Peter Fellmeth, Vector Informatik GmbH The upcoming ISO standard will be the preferred tractor Implement interface in the agricultural industry. Therefore the ISO
More informationAutomated Data Acquisition & Analysis. Revolutionize Validation Testing & Launch With Confidence
Automated Data Acquisition & Analysis Revolutionize Validation Testing & Launch With Confidence Stop waiting for this... Pass Fail CONTROLTEC is leveraging 21st century technologies to enable customers
More informationl i X t o CASE STUDY Beyond electronic data interchange (EDI)
l i X t o Automating transactions in logistics processes: Beyond electronic data interchange (EDI) CASE STUDY VOSS Automotive collects information about delivery requests automatically from web portals
More informationThe RT module VT6000 (VT6050 / VT6010) can be used to enhance the RT. performance of CANoe by distributing the real-time part of CANoe to a
Getting started with VT6000 and VT6104 The RT module VT6000 (VT6050 / VT6010) can be used to enhance the RT performance of CANoe by distributing the real-time part of CANoe to a dedicated RT execution
More informationDr.-Ing. Rainer Rasche dspace GmbH Rathenaustrasse 26 33102 Paderborn automotive testing expo June 22, 2010
Combining Two Worlds: Precise Real-Time- Based and Convenient PC-Based Testing Dr.-Ing. Rainer Rasche dspace GmbH Rathenaustrasse 26 33102 Paderborn nd automotive testing expo June 22, 2010 Agenda Testautomation
More informationI2C PRESSURE MONITORING THROUGH USB PROTOCOL.
I2C PRESSURE MONITORING THROUGH USB PROTOCOL. Product Details: To eradicate human error while taking readings such as upper precision or lower precision Embedded with JAVA Application: Technology Used:
More informationValidating Diagnostics in Early Development Stages
Validating Diagnostics in Early Development Stages Explanations by means of an Example of an automatic exterior lighting control Dipl.-Ing. Valentin Adam, Daimler AG Dipl.-Ing. Matthias Kohlweyer, Daimler
More informationTrace Port Analysis for ARM7-ETM and ARM9-ETM Microprocessors
Trace Port Analysis for ARM7-ETM and ARM9-ETM Microprocessors Product Overview Introduction Quickly and accurately determine the root cause of your team s most difficult hardware, software, and system
More informationARM Ltd 110 Fulbourn Road, Cambridge, CB1 9NJ, UK. *peter.harrod@arm.com
Serial Wire Debug and the CoreSight TM Debug and Trace Architecture Eddie Ashfield, Ian Field, Peter Harrod *, Sean Houlihane, William Orme and Sheldon Woodhouse ARM Ltd 110 Fulbourn Road, Cambridge, CB1
More informationCAN-based Protocols in Avionics Version 1.1 2012-04-12 Application Note AN-ION-1-0104
Version 1.1 2012-04-12 Author(s) Restrictions Abstract Jürgen Klüser Public Document This application note provides an overview of communication protocols used in CANbased avionics networking. Table of
More informationWISE-4000 Series. WISE IoT Wireless I/O Modules
WISE-4000 Series WISE IoT Wireless I/O Modules Bring Everything into World of the IoT WISE IoT Ethernet I/O Architecture Public Cloud App Big Data New WISE DNA Data Center Smart Configure File-based Cloud
More informationSimple and error-free startup of the communication cluster. as well as high system stability over long service life are
Network Management for FlexRay New network topologies tested in practice Simple and error-free startup of the communication cluster as well as high system stability over long service life are required
More informationHardware Virtualization for Pre-Silicon Software Development in Automotive Electronics
Hardware Virtualization for Pre-Silicon Software Development in Automotive Electronics Frank Schirrmeister, Filip Thoen fschirr@synopsys.com Synopsys, Inc. Market Trends & Challenges Growing electronics
More informationHow to design and implement firmware for embedded systems
How to design and implement firmware for embedded systems Last changes: 17.06.2010 Author: Rico Möckel The very beginning: What should I avoid when implementing firmware for embedded systems? Writing code
More informationDS1104 R&D Controller Board
DS1104 R&D Controller Board Cost-effective system for controller development Highlights Single-board system with real-time hardware and comprehensive I/O Cost-effective PCI hardware for use in PCs Application
More informationThe Answer to the 14 Most Frequently Asked Modbus Questions
Modbus Frequently Asked Questions WP-34-REV0-0609-1/7 The Answer to the 14 Most Frequently Asked Modbus Questions Exactly what is Modbus? Modbus is an open serial communications protocol widely used in
More informationEmbedding Trust into Cars Secure Software Delivery and Installation
Embedding Trust into Cars Secure Software Delivery and Installation André Adelsbach, Ulrich Huber, Ahmad-Reza Sadeghi, Christian Stüble Horst Görtz Institute for IT Security, Bochum, Germany Third Workshop
More informationASAM ODS, Peak ODS Server and openmdm as a company-wide information hub for test and simulation data. Peak Solution GmbH, Nuremberg
ASAM, and as a company-wide information hub for test and simulation data Peak Solution GmbH, Nuremberg Overview ASAM provides for over a decade a standard, that has proven itself as a reliable basis for
More informationQuick Introduction to CANalyzer Version 1.1 2009-09-08 Application Note AN-AND-1-110
Version 1.1 2009-09-08 Application Note AN-AND-1-110 Restrictions Abstract Public Document This application note focuses on quickly learning several key CANalyzer skills. The aim is to move first time
More informationNational CR16C Family On-Chip Emulation. Contents. Technical Notes V9.11.75
_ V9.11.75 Technical Notes National CR16C Family On-Chip Emulation Contents Contents... 1 1 Introduction... 2 2 Emulation options... 3 2.1 Hardware Options... 3 2.2 Initialization Sequence... 4 2.3 JTAG
More informationSample Project List. Software Reverse Engineering
Sample Project List Software Reverse Engineering Automotive Computing Electronic power steering Embedded flash memory Inkjet printer software Laptop computers Laptop computers PC application software Software
More informationCorporate Finance in the Automotive Arena. - Navigating the next decade. of auto industry transformation -
Corporate Finance in the Automotive Arena - Navigating the next decade of auto industry transformation - Jens Diehlmann Partner at IBM Global Business Services; Global Leader Captive Finance Agenda 1 Who
More informationGetting Started with CANopen Version 1.1 2008-05-29 Application Note AN-AON-1-1102
Version 1.1 2008-05-29 Restrictions Abstract Public Document This application note explains items which need to be considered when creating a CANopen device or system. The Manager, Systems Engineer, and
More informationOpen Source Software
Open Source Software Title Experiences and considerations about open source software for standard software components in automotive environments 2 Overview Experiences Project Findings Considerations X-by-wire
More informationMicrocomputer Protocol Implementation at Local Interconnect Network Georgi Krastev
Microcomputer Protocol Implementation at Local Interconnect Network Georgi Krastev Abstract: The paper discusses the issues of microcomputer protocol implementation at local interconnect network for automobile
More informationWireless Microcontrollers for Environment Management, Asset Tracking and Consumer. October 2009
Wireless Microcontrollers for Environment Management, Asset Tracking and Consumer October 2009 Jennic highlights Jennic is a fabless semiconductor company providing Wireless Microcontrollers to high-growth
More informationChapter 13. PIC Family Microcontroller
Chapter 13 PIC Family Microcontroller Lesson 01 PIC Characteristics and Examples PIC microcontroller characteristics Power-on reset Brown out reset Simplified instruction set High speed execution Up to
More informationWhat s New in 2013. Mike Bailey LabVIEW Technical Evangelist. uk.ni.com
What s New in 2013 Mike Bailey LabVIEW Technical Evangelist Building High-Performance Test, Measurement and Control Systems Using PXImc Jeremy Twaits Regional Marketing Engineer Automated Test & RF National
More informationSolutions for MOST. Reliable Solutions for MOST25, MOST50 and MOST150 ENGLISH
Solutions for MOST Reliable Solutions for MOST25, MOST50 and MOST150 ENGLISH 2 Solutions for Your MOST Networking Vector is your solution provider for MOST with MOST25, MOST50 and MOST150 we support you
More informationApplication of Android OS as Real-time Control Platform**
AUTOMATYKA/ AUTOMATICS 2013 Vol. 17 No. 2 http://dx.doi.org/10.7494/automat.2013.17.2.197 Krzysztof Ko³ek* Application of Android OS as Real-time Control Platform** 1. Introduction An android operating
More informationSoftware Module Test for an Electronic Steering Lock
Software Module Test for an Electronic Steering Lock Wolfgang Beer, Dr. Peter Jüttner, Daniel Simonis (external subcontractor), Siemens VDO Automotive AG Siemensstr. 12 93055 Regensburg, Germany Tel.:
More informationNetwork connectivity controllers
Network connectivity controllers High performance connectivity solutions Factory Automation The hostile environment of many factories can have a significant impact on the life expectancy of PCs, and industrially
More informationTackling the Complexity of Timing-relevant Deployment Decisions in Multicore-based Embedded Automotive Software Systems Rolf Schneider, AUDI AG
Tackling the Complexity of Timing-relevant Deployment Decisions in Multicore-based Embedded Automotive Software Systems Rolf Schneider, AUDI AG 1 Topics Introduction Project ARAMiS ARAMiS Automotive LSSI
More information