MODEL SPACE PAPER SPACE. Thus far, we ve been working on drawing in a single view. This view is called Model Space.
|
|
- Jewel Hoover
- 1 years ago
- Views:
Transcription
1 MODEL SPACE VS Thus far, we ve been working on drawing in a single view. This view is called Model Space. Everything drawn here is at 1:1 (full) scale. PAPER SPACE To set up multiple views of a drawing and specify the scale of those views we ll begin to work with Viewports in Paper Space. We ll also do all annotation of drawings in Paper Space.
2 MODEL SPACE To switch between Model Space and Paper Space, use the Quick View Layout button in the Status Bar at the bottom of your screen. Select A1.1 from within the SampleProject1.dwg file that you downloaded last week. Quick View Layout
3 PAPER SPACE You should see a layout of a drawing. The white area designates the size of paper that has been set up for this drawing. Use your mouse scroll wheel to zoom in and out.
4 PAPER SPACE Type MS, Spacebar to access model space (the drawing area boundary will be highlighted). You are now accessing the original drawing model area through the space of the paper. Try zooming in and out with your mouse notice the difference.
5 PAPER SPACE Type U, Spacebar to undo changes, then Esc to exit the command. Type PS, Spacebar to return to paperspace.
6 Hover your cursor over the two rectangles at the boundary of the page: one is a Viewport and one is a Polyline. Click once to select the Viewport.
7 Try resizing the boundary of the viewport simply by dragging one corner of it. Notice that it behaves differently from other shapes. Compare this action to the behavior of polylines by resizing the other rectangle on the page.
8 To create a new Layout, type layout, Spacebar. Type N for a new layout (note you can type C to copy an existing layout). Follow the command line prompts to title the layout. Then, select the new layout with the Quick View Layout Button.
9 CREATING VIEWPORTS Erase the existing boundary (E, Spacebar) and type Vports to create a new viewport (boundary) for your drawing. Select Active Model Configuration. Ensure the settings for the new viewport match those shown here. Select OK.
10 After making the selections from the previous slide, draw a bounding box on the page this is the viewport. Type MS to access model space and type Z, Spacebar, E, Spacebar to zoom extents (use this command when you ve lost your drawing!) Type Z, Spacebar, W, Spacebar and use P to pan around the drawing and center it on the page.
11 CREATING VIEWPORTS Boundary not showing up? Make sure you ve drawn it on an active Layer. The lightbulb here is off so anything drawn on this layer won t be visible.
12 Type pagesetup, Spacebar. Select the new layout you ve created to modify its page setup.
13 Select Printer and Paper Size DO NOT select Plot Scale Here! Note that if you ve successfully installed a PDF generator, it will appear in your printer/plotter options. You can also select None and set up a printer later. Select Drawing Orientation
14 Extend the boundaries of the viewport to match the new page dimensions. The page layout is at 1:1 scale and the drawing must be set to a proper print scale that will fit on the page.
15 Highlight the bounding edge of the viewport and, in the properties window, select ½ =1-0 scale from the Standard scale pull-down menu. Drawing scale must be set here and not in the page setup window! If the drawing is not centered, type MS, Spacebar and use the P command to pan. DO NOT USE THE SCOLL WHEEL OR YOUR SCALE WILL CHANGE!
16 PROPERTIES Has your Properties window disappeared? Type properties into the command line. Is your Properties window in the way? Resize it or tuck it out of view when it s not in use. It can be docked on either side of the drawing, too.
17 Return to model space by selecting model from the Quick View Layout button.
18 Return to the new layout in paperspace and type pagesetup to preview the plot. Select Window in Plot Area. You ll be prompted to draw a window around the drawing area (or press the Window button). Then, select Preview.
19 This is what the plot will look like. There are a few problems: 1. The lines are showing up in color, not as black lines. 2.The plot is also not centered. Press Esc once to return to the Setup window.
20 Select Center to Plot for an improved layout. Preview again to test out this change.
21 To ensure the lines print in black in the proper line weights, and not in color as arbitrary line weights, we must set up plot styles. Notice that this file says the assigned plot style table is missing (LKM.ctb). If a file is missing, line weights will not plot properly. Select AIA Standard.ctb and then select the Edit button.
22 PLOT STYLES Note: if the Plot Style options do not end in.ctb you will need to convert to Color Dependent Plot Styles. Exit out of the print menu (press Cancel) to do this. Note: If you do see.ctb files, skip this step. While in Model Space or Paper Space: type CONVERTPSTYLES into the command line. Click OK in the window that appears to switch modes.
23 If you skipped the last step, you may skip this step as well. If you completed the last step and this screen appears, select Cancel. If it does not appear, proceed with converting Named plot styles to Color Dependent plot styles.
24 PLOT STYLES By selecting Black as the Color option, you are telling the printer to print a line in Black rather than in its object color (red, yellow, green, etc). The lineweight setting will translate a color that s been set in Layers into a specified line thickness.
25
26 Make the changes noted here to get started with a plot style. You can make adjustments in the future, based on how the printers and plotters handle your line weights.
27 Note that Color 8 is also changed to 50 for its screening this means that it will print at 50% blackness, or gray. This may not work on all plotters. When finished, select Save & Close.
28 Once you return to the setup window, select the new plot style you created from the pulldown menu, then select Preview to view the changes. Note that all lines now appear as black or gray.
29 PLOT STYLE LOCATION Where is this plot style file located? Only on your computer. If you plot from another computer, you must remember to bring a copy of your plot style file along with your drawing file. Here s where the plot styles are located: Or, type stylesmanager into the command line. It s good practice to keep a copy of the.ctb file on the flash drive you used for moving files to lab computers for plotting. Be sure to place this file in the appropriate Autodesk folder on the computer you re plotting from.
30 PLOT & PRINT Type plot or press Ctrl + P to access the print window. It is similar to the page setup window, but from this window you may print / plot your files. Select the More Options arrow to expand the window.
31 Always double-check all of your settings and Preview prior to plotting.
32 You may install the studio plotter drivers directly onto your own laptop, and connect your laptop directly to the plotter for faster plotting (instead of plotting over the network). HP Designjet 500 nload.jsp?lang=en&cc=us&prodnameid=377952&taskid=135& prodtypeid=18972&prodseriesid=25301&lang=en&cc=us HP Designjet 800 nload.jsp?prodnameid=377955&lang=en&cc=us&taskid=135& prodtypeid=18972&prodseriesid=25302 These links are also available directly from the course website.
33 OTHER TIPS If, in the preview mode, some objects do now show up, return to the Layer menu to adjust their settings ensure the printer icon does not have a slash thru it and that the lightbulb for the layer is turned on.
34 OTHER TIPS If you find that some lines are plotting in shades of gray (or preview as gray) return to the plot style editor window to double-check the Screening selection for the line color. Set the Sreening to 100 to plot black lines.
35 LINETYPES To use varying linetypes (dashed, dotted, centerline, etc) in your drawing you ll first need to load them. To do so, type linetype into the command line. Select Show all linetypes from the pulldown menu in the window, then select Load. Select a few linetypes from the list that appears. Dashed, Dashed 2 and Centerline will be useful. You can always add more.
36 LINETYPES In Model Space, select an object within the drawing. From the Properties menu, assign the object a linetype.
37 LINETYPES You may have to adjust the Linetype scale in the Properties menu to ensure lines appear properly in Model Space as well as in a Preview of your final Plot. Check the scale of your linetypes in both these places before beginning a drawing to save time making adjustments later.
38 When drafting related drawings, it is often useful to align them in model space, just as you would in hand drafting. While using the move command with Osnap turned on (F3), alignments are easy to locate.
39 A drawing may be turned into a writeblock for use as an underlay or for other purposes. The elements in the block will act like a group. Type wblock, Spacebar.
40 Select Convert to Block Select a destination on your computer, preferably the source folder for the original file.
41 For better visibility, all lines can be set to a single color. Note that this block may be placed on top of other elements without affecting them and can be easily selected as a unit. The block Blocks may be turned back into lines using the Explode command.
42 Note that the writeblock file you ve created is a new AutoCAD.dwg file it can be used and edited in the same manner you d use any other AutoCAD file. When inserting a new writeblock into a drawing, a link is created so that updated to the source writeblock automatically propagate into the file it s used in.
43 1. The block may be edited at the source file, or from within the drawing it s being used in. 2. Select block, rightclick, select Block Editor. 3. Make revisions to the block. 4. With no objects selected, right-click, select Close Block Editor. 5. You ll be prompted to save changes to block source file select yes to propagate changes.
44 MATCH PROPERTIES Once line colors, weights and other attributes have been assigned to a drawing the Match Properties tool will be useful. It allows you to select the attributes of one item and assign them to others elements. Although you can type matchprop into the command line, it s a long command and easiest to access from the palette shown above. Select the source, then select the objects to which the properties will be applied.
45 POLYLINE A polyline is a connected sequence of line segments that function as a single object. Type PL, spacebar to access it. Click on the drawing to begin, using Ortho (F8) as necessary. Type ARC, spacebar midcommand to add curved line segments. Type L to return to straight lines. Return to your original point to complete the shape, right-click and select Enter or Close.
46 POLYLINE While drawing a polyline (or any other line), type PER mid-command to extend a line perpendicular to another line in the distance. Type C mid-command and the polyline will automatically close itself. Select the polyline (or other geometric object) and type EXPLODE to turn it into individual line segments. Polylines are especially useful when adding tone or hatch to an irregularly shaped area.
47 HATCH To add hatch, type BH, spacebar. Select a pattern from the pulldown menu. Click Add: Select Objects. You ll be brought to your drawing to choose objects to hatch. When done, right-click, Enter. Click OK. Hatch may only be added to areas with closed boundaries (geometric shapes, polylines).
48 HATCH Your hatch might be too dense. This will make AutoCAD run slowly is generally undesirable. To adjust it, select the hatch area, right click, select Hatch Edit. Adjust the Scale from within the window that appears.
49 PATTERNS When is it appropriate to use patterns in a drawing? Very, very, very rarely for the same reasons we don t use green grass and lifelike tress in architectural models. Patterns often distract from overall design ideas and prevent the ability to customize the overall layout of the elements. For your drawings, you may only use hatch patterns in a limited manner, in a very light lineweight.
Chapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives
Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to
Converting an AutoCAD Drawing into PDF File
Tutorial Created by Brijesh Bhatha, 2004. Updated 2006 by Corinne Stewart (corinnestewart@gmail.com) CP-208 Plan Preparation Studio - Prof. Elizabeth Macdonald 2 In this tutorial we will learn to create
Creating a Poster in PowerPoint 2010. A. Set Up Your Poster
View the Best Practices in Poster Design located at http://www.emich.edu/training/poster before you begin creating a poster. Then in PowerPoint: (A) set up the poster size and orientation, (B) add and
Introduction to Google SketchUp (Mac Version)
Introduction to Google SketchUp (Mac Version) This guide is handy to read if you need some basic knowledge to get started using SketchUp. You will see how to download and install Sketchup, and learn how
Introduction to Word 2007
Introduction to Word 2007 You will notice some obvious changes immediately after starting Word 2007. For starters, the top bar has a completely new look, consisting of new features, buttons and naming
TABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
SnagIt Add-Ins User Guide
Version 8.1 User Guide By TechSmith Corp. User Guide User Guide Contents User s Guide 1 Overview...1 Word, PowerPoint, and Excel Add-Ins...2 Outlook Add-In...2 Internet Explorer / Windows Explorer Add-In...2
Edinburgh COLLEGE of ART ARCHITECTURE 3D Modelling in AutoCAD - tutorial exercise The screen The graphics area This is the part of the screen in which the drawing will be created. The command prompt area
Introduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
Introduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
Basic AutoSketch Manual
Basic AutoSketch Manual Instruction for students Skf-Manual.doc of 3 Contents BASIC AUTOSKETCH MANUAL... INSTRUCTION FOR STUDENTS... BASIC AUTOSKETCH INSTRUCTION... 3 SCREEN LAYOUT... 3 MENU BAR... 3 FILE
Lesson Four 3D Modeling
Lesson Four 3D Modeling In this lesson you will learn how to: Easily Rotate the UCS to model in different planes Model lines in a method similar to drawing isometrics Create 3D Router Lines Automatically
Migrating to Excel 2010 from Excel 2003 - Excel - Microsoft Office 1 of 1
Migrating to Excel 2010 - Excel - Microsoft Office 1 of 1 In This Guide Microsoft Excel 2010 looks very different, so we created this guide to help you minimize the learning curve. Read on to learn key
An introduction to 2D AutoCAD
An introduction to 2D AutoCAD Faculty of Technology University of Plymouth Drake Circus Plymouth PL4 8AA Contents: 1 Introduction.... 3 1.1 What is AutoCAD?... 3 1.2 The interface.... 3 1.3 Saving your
Microsoft PowerPoint 2010 Handout
Microsoft PowerPoint 2010 Handout PowerPoint is a presentation software program that is part of the Microsoft Office package. This program helps you to enhance your oral presentation and keep the audience
Site Analysis / Research. STEP 1: In Illustrator open your class-02 file _ go to the main menu File _ Export
Site Analysis / Research STEP 1: In Illustrator open your class-02 file _ go to the main menu File _ Export STEP 2: from the Export window set the Save as Type to: AutoCAD Drawing (*DWG) _ Save the file
Layout Tutorial. Getting Started
Getting Started Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating
Microsoft Migrating to Word 2010 from Word 2003
In This Guide Microsoft Word 2010 looks very different, so we created this guide to help you minimize the learning curve. Read on to learn key parts of the new interface, discover free Word 2010 training,
SpaceClaim Introduction Training Session. A SpaceClaim Support Document
SpaceClaim Introduction Training Session A SpaceClaim Support Document In this class we will walk through the basic tools used to create and modify models in SpaceClaim. Introduction We will focus on:
SketchUp Instructions
SketchUp Instructions Every architect needs to know how to use SketchUp! SketchUp is free from Google just Google it and download to your computer. You can do just about anything with it, but it is especially
Epson Brightlink Interactive Board and Pen Training. Step One: Install the Brightlink Easy Interactive Driver
California State University, Fullerton Campus Information Technology Division Documentation and Training Services Handout Epson Brightlink Interactive Board and Pen Training Downloading Brightlink Drivers
Microsoft PowerPoint Tutorial
Microsoft PowerPoint Tutorial Contents Starting MS PowerPoint... 1 The MS PowerPoint Window... 2 Title Bar...2 Office Button...3 Saving Your Work... 3 For the first time... 3 While you work... 3 Backing
Updox, LLC support@updox.com 614-547-9635
Set Up and User Guide Version 3.2.2 Updox, LLC support@updox.com 614-547-9635 Table of Contents Creating and Managing Internal Updox Users... 3 How to Send and Receive Faxes... 4 How to Import Files into
Digital Marketing EasyEditor Guide Dynamic
Surveys ipad Segmentation Reporting Email Sign up Email marketing that works for you Landing Pages Results Digital Marketing EasyEditor Guide Dynamic Questionnaires QR Codes SMS 43 North View, Westbury
Producing 2D Documentation from 3D Models in AutoCAD
Producing 2D Documentation from 3D Models in AutoCAD David Cohn 4D Technologies AC4689 Modeling in 3D is fine, but eventually you need to produce 2D drawings. In this class, you will learn about tools
CREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT
CREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT 20-25 Minutes This topic is for users of PlansXpress Total Toolkit Edition. To upgrade to PlansXpress Total Toolkit, call
Florence School District #1
Florence School District #1 Module 2: SMART Board Basics and Beyond 1 SMART Board Software and Beyond In SMART Notebook software, you can create or open SMART Notebook software (.notebook) files. After
A sample script file is displayed below: DRF271.SCR snap.125 grid.5 layer make vports color blue vports. zoom all
Script Files (.SCR) Script files are simply a list of commands that are run as a group. A script file does not have the ability to stop and wait for user input. Many AutoCAD commands bring up special dialog
BrightLink Pro. Quick Reference. BrightLink Interaction. BrightLink Pro Features. 1 Turning on and Calibrating the Projector
BrightLink Pro BrightLink Interaction Three interactive modes are available: Whiteboard mode Quick Reference This card will help you get started using your BrightLink Pro interactive projector. Use one
Chapter 9 Slide Shows
Impress Guide Chapter 9 Slide Shows Transitions, animations, and more Copyright This document is Copyright 2007 2013 by its contributors as listed below. You may distribute it and/or modify it under the
CATIA Basic Concepts TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Manual Format...2 Log on/off procedures for Windows...3 To log on...3 To logoff...7 Assembly Design Screen...8 Part Design Screen...9 Pull-down Menus...10 Start...10
RV 12 Electrical Schematic Instructions
RV 12 Electrical Schematic Instructions Step 1: Set your monitor resolution as high as possible. Step 2: Download "RV 12 Electrical Systems (XXX).dwg" from the Van's Aircraft web site to your desktop.
APA-STYLE TABLES in MICROSOFT WORD 2007
Twin Cities Writing Center APA-STYLE TABLES in MICROSOFT WORD 2007 Before inserting a table into your paper, make sure a table is an appropriate way to communicate your information. Read about the use
Draw pie charts in Excel
This activity shows how to draw pie charts in Excel 2007. Open a new Excel workbook. Enter some data you can use your own data if you wish. This table gives the % of European holidays sold by a travel
Introduction to AutoCAD lar 543 spring 2008
Introduction to AutoCAD lar 543 spring 2008 for landscape architects Makie Suzuki, Chihiro Shinohara in this session we cover: - introduction - basic operation - basic drawing tools - basic editing In
LESSON 7: IMPORTING AND VECTORIZING A BITMAP IMAGE
LESSON 7: IMPORTING AND VECTORIZING A BITMAP IMAGE In this lesson we ll learn how to import a bitmap logo, transform it into a vector and perform some editing on the vector to clean it up. The concepts
Project 1 - Business Proposal (PowerPoint)
Project 1 - Business Proposal (PowerPoint) extraordinary faculty, inquisitive and talented students, a constant striving to build upon and expand historical strengths, the vision to anticipate the future,
3D-GIS in the Cloud USER MANUAL. August, 2014
3D-GIS in the Cloud USER MANUAL August, 2014 3D GIS in the Cloud User Manual August, 2014 Table of Contents 1. Quick Reference: Navigating and Exploring in the 3D GIS in the Cloud... 2 1.1 Using the Mouse...
Merging Labels, Letters, and Envelopes Word 2013
Merging Labels, Letters, and Envelopes Word 2013 Merging... 1 Types of Merges... 1 The Merging Process... 2 Labels - A Page of the Same... 2 Labels - A Blank Page... 3 Creating Custom Labels... 3 Merged
Tutorial Guide to AutoCAD 2013
Tutorial Guide to AutoCAD 2013 2D Drawing, 3D Modeling Shawna Lockhart SDC P U B L I C AT I O N S Schroff Development Corporation For Microsoft Windows Better Textbooks. Lower Prices. www.sdcpublications.com
Using Kid Pix Deluxe 3 (Windows)
Using Kid Pix Deluxe 3 (Windows) KidPix Deluxe 3 is a multimedia software program that is especially effective for use with primary level students. Teachers and students can create animated slide presentations
2. How to Use SMART Board as a Projector and Whiteboard
Page 1 Smart Board Getting Started Smart Board is an interactive whiteboard developed by SMART Technologies that combines the capabilities of a data projector and a white board. Use the SMART Board to
SMART BOARD USER GUIDE FOR PC TABLE OF CONTENTS I. BEFORE YOU USE THE SMART BOARD. What is it?
SMART BOARD USER GUIDE FOR PC What is it? SMART Board is an interactive whiteboard available in an increasing number of classrooms at the University of Tennessee. While your laptop image is projected on
2013 Getting Started Guide
2013 Getting Started Guide The contents of this guide and accompanying exercises were originally created by Nemetschek Vectorworks, Inc. Vectorworks Fundamentals Getting Started Guide Created using: Vectorworks
PowerPoint 2007: Basics Learning Guide
PowerPoint 2007: Basics Learning Guide What s a PowerPoint Slide? PowerPoint presentations are composed of slides, just like conventional presentations. Like a 35mm film-based slide, each PowerPoint slide
An introduction to 3D draughting & solid modelling using AutoCAD
An introduction to 3D draughting & solid modelling using AutoCAD Faculty of Technology University of Plymouth Drake Circus Plymouth PL4 8AA These notes are to be used in conjunction with the AutoCAD software
Intro to Excel spreadsheets
Intro to Excel spreadsheets What are the objectives of this document? The objectives of document are: 1. Familiarize you with what a spreadsheet is, how it works, and what its capabilities are; 2. Using
K e y b o a r d s h o rt c ut s
Keyboard shortcuts Mouse navigation Middle button (wheel) Click + drag = pan Double-click = re-center view Left button Click = tool operation Click + spacebar = pan Shift + click + drag = multi-select
ArcGIS. Tips and Shortcuts. for Desktop
ArcGIS Tips and Shortcuts for Desktop Map Navigation Refresh and redraw the display. F5 Suspend the map s drawing. F9 Zoom in and out. Center map. Roll the mouse wheel backward and forward. Hold down Ctrl
Inking in MS Office 2013
VIRGINIA TECH Inking in MS Office 2013 Getting Started Guide Instructional Technology Team, College of Engineering Last Updated: Fall 2013 Email tabletteam@vt.edu if you need additional assistance after
Using Your Polyvision Digital Whiteboard and Walk-and-Talk
Using Your Polyvision Digital Whiteboard and Walk-and-Talk What is Walk-and-Talk? The Walk-and-Talk Digital Whiteboard is a remote control operated interactive system that connects to your computer. You
Microsoft Word 2010 Training
Microsoft Word 2010 Training Microsoft Word 102 Instructor: Debbie Minnerly Course goals Learn how to work with paragraphs. Set tabs and work with tables. Learn about styles Use the spelling and grammar
Creating Drawings in Pro/ENGINEER
6 Creating Drawings in Pro/ENGINEER This chapter shows you how to bring the cell phone models and the assembly you ve created into the Pro/ENGINEER Drawing mode to create a drawing. A mechanical drawing
Creating Fill-able Forms using Acrobat 8.0: Part 1
Creating Fill-able Forms using Acrobat 8.0: Part 1 The first step in creating a fill-able form in Adobe Acrobat is to generate the form with all its formatting in a program such as Microsoft Word. Then
Tutorial - First Level: 2D Fundamentals
AutoCAD 2013 Prepares you for the Autodesk Certified Associate Exam Tutorial - First Level: 2D Fundamentals Randy H. Shih Multimedia DVD SDC PUBLICATIONS Schroff Development Corporation Better Textbooks.
What s New V 11. Preferences: Parameters: Layout/ Modifications: Reverse mouse scroll wheel zoom direction
What s New V 11 Preferences: Reverse mouse scroll wheel zoom direction Assign mouse scroll wheel Middle Button as Fine tune Pricing Method (Manufacturing/Design) Display- Display Long Name Parameters:
Sage Accountants Business Cloud EasyEditor Quick Start Guide
Sage Accountants Business Cloud EasyEditor Quick Start Guide VERSION 1.0 September 2013 Contents Introduction 3 Overview of the interface 4 Working with elements 6 Adding and moving elements 7 Resizing
Data Visualization. Prepared by Francisco Olivera, Ph.D., Srikanth Koka Department of Civil Engineering Texas A&M University February 2004
Data Visualization Prepared by Francisco Olivera, Ph.D., Srikanth Koka Department of Civil Engineering Texas A&M University February 2004 Contents Brief Overview of ArcMap Goals of the Exercise Computer
WebEx Sharing Resources
WebEx Sharing Resources OTS PUBLICATION: WX0 REVISED: 4/8/06 04 TOWSON UNIVERSITY OFFICE OF TECHNOLOGY SERVICES =Shortcut =Advice =Caution Introduction During a WebEx session, the host has the ability
TABLE OF CONTENTS SURUDESIGNER YEARBOOK TUTORIAL. IMPORTANT: How to search this Tutorial for the exact topic you need.
SURUDESIGNER YEARBOOK TUTORIAL TABLE OF CONTENTS INTRODUCTION Download, Layout, Getting Started... p. 1-5 COVER/FRONT PAGE Text, Text Editing, Adding Images, Background... p. 6-11 CLASS PAGE Layout, Photo
GYM PLANNER. User Guide. Copyright Powerzone. All Rights Reserved. Software & User Guide produced by Sharp Horizon. www.sharphorizon.com.
GYM PLANNER User Guide Copyright Powerzone. All Rights Reserved. Software & User Guide produced by Sharp Horizon. www.sharphorizon.com. Installing the Software The Powerzone gym Planner is a piece of software
ACS Version 10.6 - Check Layout Design
ACS Version 10.6 - Check Layout Design Table Of Contents 1. Check Designer... 1 About the Check Design Feature... 1 Selecting a Check Template... 2 Adding a Check Template... 2 Modify a Check Template...
Web GIS User Guide MainStreetGIS, LLC
Web GIS User Guide MainStreetGIS, LLC www.mainstreetgis.com Navigation There are two ways to navigate the map interface: 1. Activate one of the map tools a. Zoom In Tool Activate the tool, then click on
BLOCKS and AutoCAD DesignCenter
BLOCKS and AutoCAD DesignCenter Chapter Objectives After completing this chapter you should: 1. understand the concept of creating and inserting symbols in AutoCAD drawings; 2. be able to use the Block
SMART Board Tips & Tricks (version 9.0) Getting Started. SMART Tools vs. SMART Notebook software
SMART Board Tips & Tricks (version 9.0) Getting Started SMART Tools vs. SMART Notebook software Click the SMART Board icon (in the system tray at the bottom right of your screen) to access the SMART Board
To develop an understanding of the basic principles of drawing using AutoCAD. 3) Deduce the intersection lines for intersected cylinders.
PROGRAMME: COURSE NAME: NATIONAL DIPLOMA IN INTERIOR DESIGN COMPUTER AIDED DESIGN (2D) COURSE CODE: ARC 213 DURATION: 0 4 4 UNITS: GOAL: GENERAL OBJECTIVES: 4 UNIT To develop an understanding of the basic
Microsoft Word 2010 Tutorial
1 Microsoft Word 2010 Tutorial Microsoft Word 2010 is a word-processing program, designed to help you create professional-quality documents. With the finest documentformatting tools, Word helps you organize
Guide To Creating Academic Posters Using Microsoft PowerPoint 2010
Guide To Creating Academic Posters Using Microsoft PowerPoint 2010 INFORMATION SERVICES Version 3.0 July 2011 Table of Contents Section 1 - Introduction... 1 Section 2 - Initial Preparation... 2 2.1 Overall
Introduction To Microsoft Office PowerPoint 2007. Bob Booth July 2008 AP-PPT5
Introduction To Microsoft Office PowerPoint 2007. Bob Booth July 2008 AP-PPT5 University of Sheffield Contents 1. INTRODUCTION... 3 2. GETTING STARTED... 4 2.1 STARTING POWERPOINT... 4 3. THE USER INTERFACE...
S M A R T D R A W U S E R G U I D E : F u n d a m e n t a l s f o r N e w U s e r s
2016 S M A R T D R A W U S E R G U I D E : F u n d a m e n t a l s f o r N e w U s e r s TABLE OF CONTENTS Introduction... 5 Getting Started in SmartDraw... 6 Home Screen... 6 How to Search for a Template
New Features in Microsoft Office 2007
New Features in Microsoft Office 2007 TABLE OF CONTENTS The Microsoft Office Button... 2 The Quick Access Toolbar... 2 Adding buttons to the Quick Access Toolbar... 2 Removing buttons from the Quick Access
PowerPoint 2013: Basic Skills
PowerPoint 2013: Basic Skills Information Technology September 1, 2014 1 P a g e Getting Started There are a variety of ways to start using PowerPoint software. You can click on a shortcut on your desktop
If you know exactly how you want your business forms to look and don t mind detail
Advanced Form Customization APPENDIX E If you know exactly how you want your business forms to look and don t mind detail work, you can customize QuickBooks forms however you want. With QuickBooks Layout
Computer Training Centre University College Cork. Excel 2013 Level 1
Computer Training Centre University College Cork Excel 2013 Level 1 Table of Contents Introduction... 1 Opening Excel... 1 Using Windows 7... 1 Using Windows 8... 1 Getting Started with Excel 2013... 2
Understand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
Getting Started With DraftSight A Guide For AEC Users
Getting Started With DraftSight A Guide For AEC Users DraftSight.com Facebook.com/DraftSight Welcome to DraftSight a valuable tool for any AEC professional! DraftSight is more than a free, professional-grade
Introduction to Microsoft Word 2008
1. Launch Microsoft Word icon in Applications > Microsoft Office 2008 (or on the Dock). 2. When the Project Gallery opens, view some of the available Word templates by clicking to expand the Groups, and
Data Visualization. Brief Overview of ArcMap
Data Visualization Prepared by Francisco Olivera, Ph.D., P.E., Srikanth Koka and Lauren Walker Department of Civil Engineering September 13, 2006 Contents: Brief Overview of ArcMap Goals of the Exercise
Boardmaker and Speaking Dynamically Pro
Boardmaker and Speaking Dynamically Pro Exploring with Sample Boards Click on desktop icon Shortcut to SDPro Main Speaking Dynamically Pro main board will come up Explore for 5 to 8 minutes Hit escape
JumpStart Guide. Trimble QuickPen PipeDesigner 3D Software
L JumpStart Guide Trimble QuickPen PipeDesigner 3D Software Revision A February 2013 F Englewood Office Trimble Navigation Limited 384 Inverness Parkway, Suite 200 Englewood, Colorado 80112 (800) 234-3758
Optimizing your image with Pixlr on-line photo editor
Optimizing your image with Pixlr on-line photo editor Nick Dvoracek dvoracek@uwosh.edu In a web browser, go to http://pixlr.com/editor/ Click Open image from computer That will open a standard file dialogue
Tips & Tricks for ArcGIS. Presented by: Jim Mallard, Crime Analysis Supervisor Arlington, Texas. 2007 IACA Conference Pasadena, Ca
Tips & Tricks for ArcGIS Presented by: Jim Mallard, Crime Analysis Supervisor Arlington, Texas 2007 IACA Conference Pasadena, Ca Table of Contents Lock & Load Labels for Maximum Speed!...2 Choose your
Making a Web Page with Microsoft Publisher 2003
Making a Web Page with Microsoft Publisher 2003 The first thing to consider when making a Web page or a Web site is the architecture of the site. How many pages will you have and how will they link to
Manual. OIRE Escuela de Profesiones de la Salud. Power Point 2007
Power Point 2007 Manual OIRE Escuela de Profesiones de la Salud Power Point 2007 2008 The New Power Point Interface PowerPoint is currently the most common software used for making visual aids for presentations.
Software Application Tutorial
Software Application Tutorial Copyright 2005, Software Application Training Unit, West Chester University. No Portion of this document may be reproduced without the written permission of the authors. For
MAKING A LARGE FORMAT SCIENTIFIC POSTER USING POWERPOINT
MAKING A LARGE FORMAT SCIENTIFIC POSTER USING POWERPOINT This document covers the following topics: I. Why use Powerpoint for making a poster?...1 II. Getting Started: Formatting your Poster...1 III. Using
BIGPOND ONLINE STORAGE USER GUIDE Issue 1.1.0-18 August 2005
BIGPOND ONLINE STORAGE USER GUIDE Issue 1.1.0-18 August 2005 PLEASE NOTE: The contents of this publication, and any associated documentation provided to you, must not be disclosed to any third party without
Introduction to MS WINDOWS XP
Introduction to MS WINDOWS XP Mouse Desktop Windows Applications File handling Introduction to MS Windows XP 2 Table of Contents What is Windows XP?... 3 Windows within Windows... 3 The Desktop... 3 The
Microsoft Excel 2010 Charts and Graphs
Microsoft Excel 2010 Charts and Graphs Email: training@health.ufl.edu Web Page: http://training.health.ufl.edu Microsoft Excel 2010: Charts and Graphs 2.0 hours Topics include data groupings; creating
SE OF THE PROGRAM...5
MyHatch User guide PREFACE... 2 GOAL OF THE SOFTWARE... 2 DEFINITION OF HATCHES IN AUTOCAD... 2 MYHATCH PROGRAM... 2 DEFINITION OF HATCH PATTERNS... 3 USE OF THE PROGRAM... 5 INSTALLATION... 5 TOOLBAR
Microsoft PowerPoint 2008
Microsoft PowerPoint 2008 Starting PowerPoint... 2 Creating Slides in Your Presentation... 3 Beginning with the Title Slide... 3 Inserting a New Slide... 3 Slide Layouts... 3 Adding an Image to a Slide...
5050 Getting Started
5050 Getting Started Getting Started.. The 50/50 system is basically made up of four components, the Software Application, Server, J2 Selling Stations (on tables) and the Handheld Selling Units. This manual
Zoom Guide. Zoom Meeting Experience. Hardware Requirements. Joining a Zoom Meeting
Zoom Guide Zoom Meeting Experience Zoom is an online meeting and conferencing platform that allows for audio, video, and screen sharing. It is an easy to use and high quality solution for those students
Microsoft Word 2010. Revising Word Documents Using Markup Tools
Microsoft Word 2010 Revising Word Documents Using Markup Tools Preface Word provides several markup tools that make document collaboration easy. Color coding, highlighting, and the ability maintain multiple
GFI FAXmaker 14 for Exchange/Lotus/SMTP. Fax-Client Manual. By GFI Software Ltd
GFI FAXmaker 14 for Exchange/Lotus/SMTP Fax-Client Manual By GFI Software Ltd http://www.gfi.com Email: info@gfi.com Information in this document is subject to change without notice. Companies, names,
Basic controls of Rhinoceros 3D software
lecture 2 Basic controls of Rhinoceros 3D software After the start Rhinoceros 3D software shows basic working area compound by four viewports (show model in other positions), popup menu over, palette menu
Microsoft Access 2010 handout
Microsoft Access 2010 handout Access 2010 is a relational database program you can use to create and manage large quantities of data. You can use Access to manage anything from a home inventory to a giant
Session 25 Revit MEP Tips and Tricks
Session 25 Revit MEP Tips and Tricks Page 1 of 17 Sometimes it's the little things which make all the difference. I thought I would share some nifty tricks that can help make Revit MEP go down a little
SMART Ink 1.5. Windows operating systems. Scan the following QR code to view the SMART Ink Help on your smart phone or other mobile device.
SMART Ink 1.5 Windows operating systems User s guide Scan the following QR code to view the SMART Ink Help on your smart phone or other mobile device. Trademark notice SMART Ink, SMART Notebook, SMART
Basic Microsoft Excel 2007
Basic Microsoft Excel 2007 The biggest difference between Excel 2007 and its predecessors is the new layout. All of the old functions are still there (with some new additions), but they are now located