1 SVC400P/SVC800P Mobile Video Recorders CMS Manual
2 Content 1 Preface Run environment Main features Installation Install server Install client Server Network setup Message server Center server Transmit server Client Network Setup Functions on GUI Check version Vehicle tree Video & transmission Info Window mode Log query Download System setup Alarm Info Map Vehicle online Info Log window Basic Info. and PTZ Case studies Introduction Network diagram Bandwidth calculate... 52
3 1 Preface After you get the software, please try to setup the SVC400P/800P Mobile DVR (MDVR) and the CMS to get video first according to 3G & WIFI setup. If you don t have this document, please contact us. In this document, we introduce the basic application of the CMS. If you have a big project which has more than 100 vehicles, please contact the support team for the best solution. This software includes 4 parts: message server, transmit server, media proxy server and client. Message server is used for the register information of all the MDVR, online information, GPS information and deal with all kinds of commands. Transmit server is used to transmit video, you must add and setup the MDVR information first in the transmit server. Client is for the video display, information display and the reception of the command from the administrators. 1.1 Run environment The CMS server should be installed on 2003 server OS, for the client, it can run on XP OS and WIN7 OS. The firewall and antivirus software would stop the video transmission, so please add the exceptions ports on the firewall and close the anti-virus software if you cannot get the video. The computer must have the drive of DirectX. Please check as follows: Start Run--input dxdiag Click on OK
4 The Direct Draw Acceleration and Direct3D Acceleration must be Enabled. 1.2 Main features The standard version CMS no need to register, it can manage 100 vehicles on center server of transmit server. The transmit server can transmit 48 channels concurrently to 3 clients (each has 16 video window) at the same time. The CMS is functional which integrate the video transmission, remotely PTZ control, alarm, GPS tracking, local recording on CMS, alarm recording, and also it can show you the operating and alarm information on the log window. Also, you can change the interface to different mode easily. Message server is used for the MDVR register, GPS information and all the commands downloading. Transmit server is for the video transmission. Client, the user friendly interface, shows you all the information. Also, you can setup the MDVR remotely from the client.
5 Main features: 1. Wireless Video/Audio transmission 2. GPS tracking: show the real-time location of the vehicle on map window with MapInfo & Google map. 3. Remotely PTZ control: control the PTZ on CMS, including change direction, pre-set position, call position. 4. CMS local recording: record the video from the CMS video window. 5. Alarm report system: receive the alarm information, and deal with this alarm information according to the settings. 6. Vehicle management: manage vehicle on the transmit server, show all the vehicle information on the client vehicle window to check the online information and do some operations remotely to the MDVR. 7. Multi-clients supported: support many clients connect to the server to apply video. 8. Remotely configuration: setup the GPS upload interval, IO setup, stream setup for video transmission, get device information and so on. 9. Support DDNS 10. Support auto-shut down video function 1.3 Installation Please run these files one by one: CMS_server.exe is the server package for all the servers, including message server, transmit server; CMS_client.exe is the CMS client, you can install the client on the same PC with server, or on another PC which can connect to the server.
6 1.3.1 Install server Please double click the exe file to install the server. Click on Next to continue
7 Complete means install all the servers on this PC under C drive C:\Program Files\CMS, Custom means you can setup the installation directory and choose server need to be installed, shown as the following two pictures: Click on Next to continue:
8 Click on Next and Install to continue. During the installation, it will read the local IP automatically, If you test the MDVR and CMS in the local network (WIFI or cross cable), then please don t change this IP. But if you test 3G transmission, please setup the IP as PC s WAN IP here. Click on next to go on. After the installation, on the right down bottom, there is the server icon.
9 Please double click on this icon to check the server status Install client Please double click the exe file and click NEXT and choose Create Icon on Desktop item to finish the installation. After the installation, there will be three icons on the desktop:
10 Click on Next to finish the installation. SVC400P/SVC800P - CMS Manual
11 Click on Finish to finish the installation. SVC400P/SVC800P - CMS Manual
12 2 Server There are four servers included: Center server: vehicle & user management Transmit server: video transmission. Message server: show the device and client online information, and it is used for the communication between client and MDVR like command. Control server: make sure the center server and transmit server run stably. Reinstall these servers: Please click on center server, choose Stop server, click on Install server>> Uninstall current server, and then choose Install current server to install it. The same progress to the other servers. 2.1 Network setup Firstly, setup the network of transmit sever. Please
13 The register sever IP is the IP or DDNS which you installed message sever, as well as the corresponding port. Local public IP is the IP of the PC or DDNS on which you installed transmit sever, the default port is 7263, commend to use default port. If the device and message server are connect via internet (WAN), please input the public IP of message sever in Register Sever IP. Map the 5556, 17891,10008,7263 ports from the router to your PC. The Receive Video Data Port should be any opened free port, but we suggest using the default port Message server If the message server and the transmit server are installed on the same PC, no need to do the following setup. We suggest you to install both of them on the same PC. Please click on Configure Config Message Server to setup the IP and port.
14 Port 5556 is the default port. You can change it to any free port. But please make sure, if you change this port, on the MDVR, GUI-SETUP NETWORK--SERVER, please change the relative port.
15 In the above two pictures, the port must be the same, otherwise the MDVR cannot register on the message server. (5)Show device info.: When message server is running, click on ShowDeviceInfo button, it will pop up the window below and show the device and client online information. 2.3 Center server Center server is used for the management of vehicle and user. Please start the center server from the follow picture.
16 1. Add vehicle Click on Configure label: auto-run means run the transmit server automatically after the start up PC Choose Configure center server Input the User name admin, no password.
17 Click on OK SVC400P/SVC800P - CMS Manual
18 Please click on the button to add a group first, input the group name and Description, click OK. And then click to setup the vehicle information. Click on one group and choose Add Group button to add the sub group. If you want to add another group, please right click the blank space and click Add. Then click Add at the bottom of this interface to add vehicle:
19 Select the correct channel number Transmit IP: PC IP on which you install the transmit server Put dns: in front of the device ID. These 2 must be the same. If your settings on the MDVR are correct, you can see the ID on Massager Server
20 And for the Transmit IP, if the device and transmit server are connect via WAN, then here you should type in the public IP of the transmit server. The device ID is very important, must be the one of MDVR you want to connect, Which is the one you must input when you access to GUI, the default ID is If you don t use transmit sever, the transmit IP here should be blank. 2. Add user Click on Add to add a new user and choose Change password label to setup the password.
21 2.4 Transmit server Please click on View>> View transmission log to check the transmission information.
22 Here, you can check the transmit channels, speed, receive speed and link numbers and so on.
23 3 Client 3.1 Network Setup The sever IP is the IP of the PC installed transmit sever, if transmit sever is in LAN with CMS client, the sever IP should be LAN IP. If you connect to sever via WAN, then the IP should be public IP. If the message server and transmit sever is run normally, click on OK you will access to the CMS interface. Please input the transmit server IP here User name and password here. Click on Advance to setup more information: Default: message server, transmit server and media proxy server are installed on the same PC and all the ports needed are the default ports. That is Message server: 5556; transmit server: 7263; Any other situation, please input the right information here.
24 The media server is used for intercom, broadcast and download function. If no need to use these functions, please choose default. Click OK, enter into the main interface. 3.2 Functions on GUI Check version : click on CMS to check the version number.
25 3.2.2 Vehicle tree (1) Type in all or part of vehicle ID, click on search button, it will list all the vehicles matched.
26 : this is used to refresh the vehicle list. (2) A3 is the group name, click on this button to expand and show all the vehicles in this group. (3) If the car icon is green, it means this MDVR is online, then you can apply for video or right click on it to do some operation. And click on the vehicle name. dns:0000 in the bracket is the MDVR ID. button to show all the cameras is the (4) If the car icon is gray, it means this car is offline. (5) The black camera on the 4th channel means apply for video of this channel, white means this channel is closed. No video transmitted, like the first three channels. (6) Right click on the online vehicle to do the following operations:
27 Get version Info: If the device has some problem, you can get the version information remotely. GPS Setup: Setup the GPS upload interval. If you choose close upload GPS, you can not see the green icon on the map.
28 02009: Device ID Stream setup: Here you can setup some parts of the upload stream parameters, so if the transmission speed is not so good, you can change the total bandwidth and the frame to get a better speed. IO setup:
29 Setup the IO output of the MDVR remotely, you can control the vehicle remotely. Mileage setup: Setup the total mileage of the vehicle. Intercom:
30 For the interphone function, it needs both the CMS and the device has audio input and output. Attention: if you want to use this function, please follow the steps: 1) On the MDVR, only the fourth channel can be used as the audio input. For the audio output you can use the AV out on the DB44 of the rear panel or the Audio out on the front panel. Please make sure the monitor has the sound amplifier function, otherwise you can not hear audio output. For the audio in on MDVR, if you use the BNC cable, you need to connect a sound pick-up, the device built-in the camera. It is different with the microphone. The main parameters of the sound pick-up are as following: Resistance: 600Ω; Peak-to-peak value: 1VPP If you use DIN-jack cable, it is more easier, just connect the camera with audio in function to this cable is OK. 2) Please make sure the function is enabled on the MDVR, as the below picture SETUP RECORD CHANNEL SETTING.
31 Broad cast: First, choose the vehicle, or select one group to choose all the vehicles, and then click start to broadcast.
32 Upgrade: Please click on to choose the firmware, and click on Start button to continue the remotely upgrade. 3G dormant: This command will make the 3G module standby, the MDVR keep on recording. Remote Restart: Restart the MDVR remotely.
33 Remote Shutdown: shutdown the MDVR remotely. Listen: click on one channel to listen the voice from the device. You can get the voice from the device without open the video to reduce the data transmission. And also for the X11-4CH, X3, MINI3 and D3, when you use the interphone function, the fourth channel will be occupied, so on the CMS client you can not hear the voice of this channel even open the volume switch Video & transmission Info.
34 (1) There is only one No. for each video window. When you apply for video, it will show the MDVR ID behind the window No.. (2) After get video, it will show the date and time on the screen of MDVR. (3) Show the channel name on this window. (4) Snapshot can be used after get video. The same function with snapshot in list after right click. X means close this video. (5) Right click on the video window, you can do the following operations: Close video: Only close the video, but remain the device ID and Channel No. on this window, so next time you can choose 5) open video to open this channel video automatically in this window. Close All: close all the video windows. Snapshot:get picture of current window. The save path is configured in system setup. Or click on the camera icon to snapshot
35 Record: click to record this channel and save to PC. There will be an R on right top of this channel. Note: record means record the video from the CMS, and save path is the one setup in system. And once the network disconnect, it will pack; otherwise pack it every 30 minutes. Open video: only available when close one channel. Open all: click to open all closed channels Clear Data: clear all the data of the window you choose, shown as the blow picture, no channel information stays in this window. Clear all the data: clear all the data of all the current open windows. Scale: 3 options: default is fulfill the screen; 4:3; 16:9 Full screen: Full screen this channel. (6) Get video info. : Green means the CMS is receiving video now. : can not get video. VOLT: voltage of the power input. Frame: the frame in the buffer. SIZE: data package received now.
36 (7) Volume and window : Click click on the video window. this icon to turn on/ turn off the audio. CMS can only play one channel audio currently by Click to change the window number. (8) Page up and down button Page up/ page down Window mode : Three button to change to window mode. Video: video only. Map: map only. Video/Map: show video window and map together as the picture above Log query Click on the log query button on right top of the main interface to check the log
37 Choose the log type on left top of this interface and setup the device and time to query SVC400P/SVC800P - CMS Manual
38 3.2.6 Download Click on the download icon on right top of the main interface. Click on System on left top of this interface to setup the path. Choose the Device, Date, Start time, End time, Video type and channel on left part of this interface, and then click on Search button to search the video file, shown as the following picture.
39 All the video files will be shown here. Select all the files you need and click on Download button, then click on the Download button here to check the download information.
40 3.2.7 System setup Click the setup icon on right- top the window to setup the system information. System:
41 Snapshot Setup: Please tick Pop-up picture when Screenshot successfully if you want to check the picture when snapshot. Save path: the default path is C:\Program Files\CMS\CMS\SaveImage. Map: support Google map and MapInfo. If you use MapInfo, please choose the Map path here. For the register button, please refer to 4.2 Register for client. Video Mode: Real-time get video immediately, smooth 5S delay Auto-shutdown: cut off the video transmission automatically when no operation on the client.
42 Record: Record Save Path: setup the disk for the local recording, and the alarm recording on CMS. The folder will be BYDVRDATA in each disk. Alarm setup: After setup the dealing type for each event here, when the CMS receive the alarm information from the device (alarm information will be shown on the Log window Alarm Log), it will make a sound, pop-up video window and record video automatically.
43 First, click Add to add a deal type. SVC400P/SVC800P - CMS Manual
44 After setup the name, audio and video deal type, pleas click OK to add this type SVC400P/SVC800P - CMS Manual
45 Click the dealing type in the left and then the alarm type in right, then click to setup the alarm.
46 3.2.8 Alarm Info. When there is alarm, the green icon will change to be red. Click red icon to check all the alarm information.
47 3.2.9 Map In Map and Video/Map window, the Maximize button can be used. : this one is used to full screen the window When in Map mode, then if you click this icon, it only full screen the map.
48 If in Video/Map mode, it will full screen the video and map. SVC400P/SVC800P - CMS Manual
49 Vehicle online Info. : This is the total number of device : Currently online number. : the number of vehicle which has GPS info. reported Log window In this window, you can see all your operation on the system log. And also you can check all the alarm information by click on the button. Please note that alarm information here is from the device, whenever the alarm happens, the device will report this to CMS and be shown here. It is different with the alarm filter function in system setup. Right click on the log window, Scroll means: when the information is full of the log window, it can scroll down automatically, the latest information is shown on the top. Copy the information: copy information to paste it to other place.
50 Then use Ctrl+V to paste the information Basic Info. and PTZ Basic Info.: Time: :28:18 Type: Close video Device ID: dns:szgj0002 Information: Channel: 1 Click the online car, it will show you the information as follows: Click this icon to hide this part.
51 PTZ: Please click the directional button to change the camera direction. : Zoom in and zoom out. : Aperture : Focus : This is for pre-set and call position
52 4 Case studies 4.1 Introduction There are two typical cases: the first one need to transmit about 250 channels video all the time, so the PC and network must very good to match this requirement; the second one have 1000 MDVRs, but no need to transmit so many channels concurrently, so it is more easier compared with the first one. CMS can support 2000 MDVRs at the same time, and it would be a little slow and refreshes every 15~20 seconds. And if you want to get more channels at the same time, please take the 3G signal strength, bandwidth and PC performance into consideration. Here I will give you two examples: (1) Project reference 1: UNINET In this project, there are 325 vehicles, and almost 250 MDVRs' video need to be checked concurrently. All the online vehicles report the online, GPS, and alarm information back to CMS message server. Due to the limitation of the PC memory, 2 transmit servers are required for the video transmission. (4GB memory can transmit less than 200 channels) Due to the limitation of the 3G bandwidth, it won't be possible for the mass data transmission, our experience with UNINET project (one of the biggest telecommunications operators). In this project, 30 CMS clients are used for video live view checking. Each client has 16 video windows because of the limitation of the PC graphics card. (2) Project reference 2: public bus In this project, 1000 vehicles report GPS, online and alarm information back to CMS message server. Since there are not as much live video transmission as UNIET project, only one transmit server is required for video transmission and 10 clients for video checking. Conclusion: (1) For live viewing, due to the limitation of the PC graphic card, you can only view 16 channels concurrently per PC. (2) For video transmission, due to the limitation of the PC memory, one PC can transmit less than 200 channels at the same time.
53 4.2 Network diagram PC 1 and PC 2 are two servers PC. PC 1 is installed with the message server and transmit server. Message server receive all the 325 vehicle information, transmit server on the PC1 is used to transmit 200 channels. PC2 is installed with the transmit server for the transmission of the other 125 vehicles, and also has storage server for the video storage. There are many clients connect to the server to check video all the time. The above diagram shows that the client and server works in the same local network. Also the client can connect to server via WAN, diagram as follows:
54 You can only install the CMS client in a WAN PC, and then connect it to the server to realize monitoring. 4.3 Bandwidth calculate (1) Video transmission: each vehicle has one channel video transmitted, and the bandwidth is 50Kbps, 325 vehicles. 50kbps *325 = 16250Kbps = 15.87Mbps (2) GPS information: 5 seconds one packet, each packet 200Bytes, 325 vehicles. (325*200 Byte / 5)*8 = 101.7kbps = 0.1Mbps (3) Command information: like apply for video command, 325 vehicles. 2*(( 325*256 Byte )*8)=1300Kbps = 1.3Mbps So the totally bandwidth needed is = 17.27Mbps.
Appendix A. CMS(Client Management Software) A-1. Install CMS for Windows PC CMS is a program for communication between DVR and PC to control signal and video. Insert the enclosed CD, and go to CD-ROM Drive
NetClient software user manual 1-1. General information Net Client is an application which provides users not only viewing and controling remote DVRs, but also receiving realtime event data or alarm signals
i -CEN S i -CEN'S USER S Manual 2007. 08. 13. i -CEN S Table of Contents Overview of i-cen S software... 4 1 Introduction of i-cen S... 4 2 Key Features... 5 3 Key Benefits... 5 4 System Specification...
Catalogue Basic Operation... 2 For Internet Explorer... 2 For Other Non-IE Web Browsers... 5 Camera Settings... 6 System... 6 About... 6 PT Setting... 7 Backup and Restore Setup... 8 NTP Setting... 8 System
DIGICLIENT 8.0 Remote Agent Software MODEL: D17800 Series Instruction Manual English Version 1.0 Copyright 2007 Digimerge Technologies Inc Table of Contents Table of Contents About the DigiClient 8.0...
Central Management System (CMS) USER MANUAL LEGAL INFORMATION Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission
AXIS Camera Station Quick Installation Guide Copyright Axis Communications AB April 2005 Rev. 3.5 Part Number 23997 1 Table of Contents Regulatory Information.................................. 3 AXIS Camera
User Manual for ios App Shenzhen Foscam Intelligent Technology Co.,Ltd. Table of Contents Table of Contents...1 1 Overview...2 2 Access the IP Camera...2 3 Install App... 2 4 Introduction to IPCam Management
Table of Contents Chapter 1. User Interface Overview...5 Chapter 2. Installation...6 2.1 Beginning Installation...6 2.2 Starting the CMS software...10 2.3 Starting it from the Start menu...10 2.4 Starting
SMS (Server Management Software) Digital Video Recorder User s Manual Contents 1 - Introduction 2 1.1 About this manual 2 1.2 Configuration 2 1.3 SMS Functions 2 1.4 Product Information 2 1.5 System Requirements
User Manual V1.0 Notice: The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change
Pro Surveillance System 4.0 Quick Start Reference Guide 1 Table of Contents 1) Overview 3 2) Initial Setup Adding a Connection..4 3) Viewing Live Cameras...6 4) Single or Multi Channel Playback..8 5) Predetermined
TVWall User s Manual (for WindowsXP/2003/Win7/Vista) Document edition:v4.1 Document suit for all of the NVS and NVD made in our company. 1 Preface Thank you for using our products, TVWall also called TVwall
Manual Client Management Software HDR50-CMS HDR50-CMS (Client Management Software) A-1. Install HDR50-CMS for Windows PC HDR50-CMS is a program for communication between DVR and PC to control signal and
Network Video Monitor Software V126.96.36.199 Operation menu Chapter 1 Product Overview 1.1 Performance instruction Network video monitoring software is a centralized management tool for I8 protocol surveillance
MDMS Multiple Device Monitor System v1.0 User Manual Copyright 2014 All rights reserved. No part of this document may be reproduced, republished, or retransmitted in any form or by any means whatsoever,
ACS CLIENT SOFTWARE USER MANUAL 1 ACS USER GUIDE 1.1 System Requirement Recommended System Requirement OS CPU VGA RAM HDD WindowXP, Vista Pentium 4, 2Ghz 1024*768, 64MB 24bit color graphic card 1GB 20MB
IP Camera Centralization Management Client Application (IPCMonitor) May, 2010 Version 1.1 User Manual INDEX 1 I ntr o d u c ti o n...3 2 C o m p u t e r R e q uir e m e n t...3 3 I n st all ati o n...4
Cell phone client software instruction and installation 1. DVR network setting First step, enter into DVR Main menu > System > Net Services, double click Mobile Monitor > Enable the mobile view port, and
Model: FI8910W Quick Installation Guide (For Windows OS) (For MAC OS please go to page 17) Indoor MJPEG Pan/Tilt Wireless IP Camera Black White Package Contents IP Camera FI8910W with IR-Cut.x 1 DC Power
Quick-Start Guide SUPER DVR MONITORING SOFTWARE Remote Surveillance & Playback For use on Q-See s QSDT series of PC Securitiy Surveillance Cards 2 CONFIGURING ROUTER FOR REMOTE ACCESS REMOTE SURVEILLANCE
A quick user guide for your LX Apollo DVR The LX Apollo series of DVR s is designed specially for the security and surveillance field and is an outstanding digital surveillance product. It has an embedded
REMOTE AGENT USER S MANUAL Revision Date : 2006.10.02. 0 INDEX CHAPTER 1. Installation-------------------------------------------------------- 2 CHAPTER 2. Function introduction------------------------------------------------
Docufide Client Installation Guide for Windows This document describes the installation and operation of the Docufide Client application at the sending school installation site. The intended audience is
ivms-4200 Intelligent Video Management System Quick Start Guide Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION.
EM6230 e-camview HD outdoor IP camera 2 ENGLISH EM6230 e-camview HD outdoor IP camera Table of contents 1.0 Introduction... 3 1.1 Packing contents... 3 1.2 Requirements to access the camera.... 3 1.3 Major
XMEye Android Mobile Monitoring Client English Manual Written by: The test department Prepared Date: 2014-03-25 Version: V1.0 目 录 1. Introduction... 3 1.1. Brief Introduction... 3 1.2. Main Functions...
Instruction for IE network monitor This system features a built-in browser-based software that allows you to access your system remotely over your local area network (LAN) or over the Internet (WAN) using
SMS Remote Software User Manual Pro Series & Contender Series DVRs Table of Contents Chapter 1 Overview 1 1.1 In This Manual 1 1.2 Overview 1 1.3 SMS Features 1 1.4 Product Information 1 1.5 System Requirements
V46.01 Model: FI8918W Quick Installation Guide Indoor Pan/Tilt Wireless IP Camera Black White For Windows OS ------- Page 1 For MAC OS ------- Page 11 ShenZhen Foscam Intelligent Technology Co., Ltd Quick
ivms-4500 (Android Tablet) Mobile Client Software User Manual (V3.0) Thank you for purchasing our product. This manual applies to ivms-4500 (Android Tablet) mobile client software; please read it carefully
IP Wireless / Wired Camera NIGHT VISION & REMOTE PAN/TILT ROTATE User Manual WELCOME This model IP Camera is an integrated wireless IP Camera solution. It combines a high quality digital Video Camera with
LOREX CLIENT Remote Software 4.0 Instruction Manual English Version 2.0 MODEL: L20WD800 Series www.lorexcctv.com Copyright 2008 LOREX Technology Inc. Table of Contents Table of Contents Software Installation...
Mobile Viewer s Access Instruction 1 Windows mobile System...2 2 Symbian System...4 3 iphone.6 4 Blackberry..7 5 Android.11 1. Windows Mobile 1) First you need to copy a program named as "Aseesetup.CAB"
Multi Client (Integration) Installation and User s Guide Ver 12.10.x *All contents of this document may change without prior notice. INDEX 1. Index 01 2. Introduction 02 3. Installation 03 4. Using Multi
CDVS-7000 Series Remote Software Users Guide Crest Electronics, Inc. Version 12.1005 Remote Surveillance Program The remote surveillance program enables users of the Crest 7000 series DVRs to connect remotely
User s Manual of DVR DVS Remote Client Software V 4.0.1 Index Version description...4 1 Introduction...8 2 Software Install, Uninstall and use...9 2.1 Install remote client software ver4.0.1...9 2.2 Uninstall
Professional Surveillance System User s Manual \ 1 Content Welcome...4 1 Feature...5 2 Installation...6 2.1 Environment...6 2.2 Installation...6 2.3 Un-installation...8 3 Main Window...9 3.1 Interface...9
CMS-DH CENTRAL MANAGEMENT SOFTWARE CMS-DH is a central management software that allows you to view and manage up to 300 DH200 series DVRs. System Requirements Your system must meet the system requirements
ivms-4500(android) Mobile Client Software User Manual (V1.0) Thank you for purchasing our product. This manual applies to ivms-4500 (Android) mobile client software, please read it carefully for the better
ViewCam Mobile Monitoring User Manual Notice This manual may be described in some technical details not accurate or there are some printing mistakes. If some problems cannot be solved in accordance with
Fleet Manager Quick Guide (Non Maintenance Mode) Launch Fleet Manager: Open the Fleet Manager Application by: 1. Double clicking the icon located on the desktop - or 2. Via Start > Programs > MobileView
B Series Robot Model IP Camera 2013-7 V4.18 User Manual Index 1 INTRODUCTION... 3 2 APPEARANCE AND INTERFACE... 5 3 VISIT IP CAMERA FROM LAN... 6 4 VISIT IP CAMERA FROM WAN... 10 5 OTHER SETTINGS... 12
SD7000 Digital Microphone Monitor Software manual Table of Contents 1. Installing The Monitor Software 1.1 Setting Up Receivers For Monitoring 1.2 Running The Application 1.3 Shutdown 2. The Detail Monitoring
ADTVision (ios) Mobile Client Software User Manual (V1.6) Thank you for purchasing our product. This manual applies to ADTVision (ios) mobile client software, please read it carefully for the better use
DVR4x4RemoteViewer.book Page 3 Tuesday, February 15, 2005 9:19 AM DVR4C Remote Viewer Operation Manual Table of Contents EN 3 1. OVERVIEW...5 1.1 MINIMUM PC REQUIREMENTS...5 2. INSTALLING THE PROGRAM...5
HRG App for Android Devices User Guide Document 800-12218 Rev A 07/2012 Revisions Issue Date Revisions A 07/2012 New document. Contents 3 Contents 1 1 Introduction...............................................
Mobile View Software User s Manual Version 3.7.1 / 3.7.2 Table of Contents 1. Overview...2 1.1 System Requirement...2 1.2 Limitation...2 2. Install the Mobile View Software...3 2.1 Installation on a JAVA
Professional Central Monitoring Software CMS Pro Full-featured Enterprise Class Surveillance Solution User`s Manual MADE IN KOREA M11131CMSProDR This document contains preliminary information and is subject
Net Protector Admin Console USER MANUAL www.indiaantivirus.com -1. Introduction Admin Console is a Centralized Anti-Virus Control and Management. It helps the administrators of small and large office networks
V48.01 Model: FI8919W Quick Installation Guide Outdoor Pan/Tilt Wireless IP Camera For Windows OS ------- Page 1 For MAC OS ------- Page 15 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation
Professional Surveillance System User s Manual Version 4.06 Table of Contents 1 OVERVIEW AND ENVIRONMENT... 1 1.1 Overview...1 1.2 Environment...1 2 INSTALLATION AND UPGRADE... 2 2.1 Installation...2 2.2
User Manual Wireless Pan & Tilt Camera CIPCAMPTIWL v1.0 Index 1 INTRODUCTION... 4 1.1 THE PACKAGE INCLUDES... 4 1.2 FUNCTION AND FEATURES... 4 1.3 TECHNICAL SPECIFICATIONS... 4 2 APPEARANCE AND INTERFACE...
UC2 Video Surveillance Client User Manual V1.0.6 MODIFY STEPS VERSION WRITER STATUS DESCRIPTION DATE V1.0.3 BRIAN A Add access mode function 2011-4-11 V1.0.4 BRIAN A Add PTZ and user role and so on 2011-4-23
Model: FI8905E Quick Installation Guide Ourdoor POE Network Camera For Windows OS ------- Page 1 For MAC OS ------- Page 14 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation Guide - For
iphone Monitoring Software Operational Manual Welcome to use iphone monitoring software. This software can be searched from ATVCLOUD. User just input Auto id. This iphone monitoring software can be applied
Dear users, the configuration for this camera is professional, so please read the user manual carefully before using the camera. IP Camera (L series) User manual 2013-05 V1.1 Statement If the user manual
EverFocus Central Management Software for Networked Video Devices Management User s Manual Copyright EverFocus Electronics Corp. Release Date: January, 2013 Copyright 2012 EverFocus Electronics Corp. All
DVS Net (Integration) Installation and User s Guide Ver 11.10.x Digital Video Security System Digital Video Recorder www.tuniss.com PLEASE CALL TUNISS COMPUTER AT: 650-401-6138 FOR ANY QUASTIONS REGARDING
ivms-4500(windows Mobile) Mobile Client Software User Manual Version 1.0 Thank you for purchasing our product. This manual applies to ivms-4500 (Windows Mobile) mobile client software, please read it carefully
ivms-4500 (Android) Mobile Client Software User Manual (V3.1) UD.6L0202D1111A01 Thank you for purchasing our product. This manual applies to ivms-4500 (Android) V3.1 mobile client software; please read
Version 17.12 Last Updated: August 2012 2012 Verizon. All Rights Reserved. The Verizon names and logos and all other names, logos, and slogans identifying Verizon s products and services are trademarks