B/W 1 /3-INCH BASIC CCD CAMERA FCC INFORMATION. Cat. No

Transcription

1 fm Page 1 Wednesday, January 19, :40 PM Cat. No B/W 1 /3-INCH BASIC CCD CAMERA Your RadioShack B/W 1 /3-Inch Basic CCD (Charge-Coupled Device) Camera is an important addition to your security system. While designed primarily for use with the RadioShack B/W 9-Inch 4-Channel Security Monitor (Cat. No ), you can also connect it to a standard TV/monitor. The camera includes a 65-foot cable to provide extra flexibility in your system. The CCD camera provides superior 78 wide pictures even in low-light conditions, and it includes a microphone so you can hear sound from the area around the camera. Warning: This camera is not waterproof. To reduce the risk of electric shock or damage, do not expose this camera to rain or moisture. FCC INFORMATION This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits provide reasonable protection against radio and TV interference in a residential area. However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference, you can try one or more of the following corrective measures: reorient or relocate the receiving antenna increase the distance between the equipment and the radio or TV use outlets on different electrical circuits for the equipment and the radio or TV Consult your local Radio Shack store if the problem still exists. Note: You must use shielded interface cables with this equipment. WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICE- ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product s case. This symbol is intended to inform you that important operating and! maintenance instructions are included in the literature accompanying this product.! 1999 Tandy Corporation. All Rights Reserved. RadioShack is a registered trademark used by Tandy Corporation.

2 fm Page 2 Wednesday, January 19, :40 PM MOUNTING GUIDELINES MOUNTING THE CAMERA Before you mount and connect the camera, carefully plan where you will position the camera and route the cable that connects the camera to the monitor. Keep in mind the following when planning the installation. This system is designed for indoor use only. Do not install the camera where it will be exposed to high humidity or rain. Select a location for the camera so you will have a clear view of the area you want to monitor. Be sure the location is free from dust, and not in a direct line-of-sight with a light source or in direct sunlight. Do not route the cable close to power or telephone lines, transformers, or other electrical equipment that could interfere with your security system or with other systems or devices. Select a location for the camera that has an ambient temperature between 14 and 113 F. If you plan to install the camera in a location that has conditions not recommended in this manual, consult with a professional installer and consider use of a separate camera cover or housing. 2 The supplied swivel-ball joint post assembly is designed to let you mount the camera on a wood surface. If you plan to mount the camera on a different type of surface, purchase appropriate hardware at your local hardware store. Obtain mounting hardware that will support at least 10 pounds (4.5 kg), which includes the weight of the camera and the cable assembly. Follow these steps to mount the camera using the supplied post assembly. 1. Loosen the locking knob and remove the ball joint assembly from the top of the lock bolt. 2. Using the base of the post assembly as a guide, mark the locations on the mounting surface for the three supplied wall screws. 3. Drill a starter hole at each marked location. 4. Thread the screws through the holes in the base and into the holes in the mounting surface. Tighten each screw until the flange is secure.

3 fm Page 3 Wednesday, January 19, :40 PM 5. Be sure the lock bolt is tight. Thread the short, 1 /4-20 post on the ball joint assembly into the camera's threaded mounting hole. Do not overtighten it. Locking Knob 1 /4-20 Post Ball Joint Assembly Lock Bolt 6. Place the camera/ball joint assembly over the top of the lock bolt then swivel/rotate the camera as needed. (You might need someone to watch the TV or monitor to confirm the camera s position once you connect the camera to your monitor, as some small adjustment might be required.) Then tighten the locking knob only enough to secure the camera. Do not overtighten it. CONNECTING TO A STANDARD TV/MONITOR You can connect the camera to a TV/ monitor that is equipped with audio/video input jacks. Follow these steps to connect the camera. Note: For the best results, mount the camera securely before connecting the cable. 1. Connect the yellow VIDEO plug of the supplied cable to the TV/monitor s video input jack. See Typical Connections Overview on Page Connect the cable s white AUDIO plug to the TV/monitor s audio input jack. 3. Insert the supplied AC adapter s barrel plug into the receptacle of the cable s DC12V jack. Then connect the adapter to a standard AC outlet. Caution: You must use a! Class 2 power source that supplies 12 volts DC and delivers at least 200 ma. Its center tip must be set to positive and its plug must fit the CCD camera's power cable jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the CCD camera or the adapter. 4. Connect the 4-pin keyed cable plug into the matching socket on the back of the camera. Note: The plug fits only one way. If it does not immediately fit, do not force it! Turn it over and try again. 3

4 fm Page 4 Wednesday, January 19, :40 PM CONNECTING TO A 4-CHANNEL SECURITY MONITOR To connect the camera to a RadioShack 4-Channel Security Monitor, see the monitor s owner's manual for complete installation and operating instructions. CARE To enjoy your B/W 1 /3-Inch Basic CCD Camera for a long time: Keep the camera dry. If it gets wet, wipe it dry immediately. Use and store the camera only in normal temperature environments. Handle the camera gently and carefully. Don t drop it. Keep the camera away from dust and dirt. Wipe the camera with a damp cloth occasionally to keep it looking new. SPECIFICATIONS Video Receptor... B&W 1 /3 CCD Receptor Resolution ,000 pixels Video Resolution: More than 380 lines Minimum Required Illumination LUX AGC... Built in Lens mm F/1.8 fixed focus Angle of View Dimensions (HWD) /8 2 1 / /32 Inches ( mm) Weight oz (50 g.) Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice. Modifying or tampering with the camera s internal components can cause a malfunction and invalidate its warranty. If your camera is not performing as it should, take it to your local RadioShack store for assistance. 4

5 fm Page 5 Wednesday, January 19, :40 PM TYPICAL CONNECTIONS OVERVIEW Camera TV/Monitor A/V Input Jacks Supplied Cable Video (Yellow) Audio (White) DC12V Jack AC Adapter Camera 9-Inch Security Monitor Cat. No Supplied Cable Video (Yellow) Audio (White) Cable Supplied with Cat. No Mini-DIN Jack DC12V Jack 5

6 fm Page 6 Wednesday, January 19, :40 PM Limited Ninety-Day Warranty This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL- ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE- SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR- RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE- NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD- VISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you. In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period. This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX We Service What We Sell 04/99 07A99 RadioShack A Division of Tandy Corporation Fort Worth, Texas Printed in Korea