Twin Photobeam Detectors Manual

Transcription

1 Aso Avaiabe from SECO-LARM: Quad Photobeam Detectors Curtain Sensors Long-Range Barrier Sensors 4 Modes avaiabe - up to 660 ft. (200m) range. 12~24 VAC/VDC Laser-beam aignment Refective Photobeam Sensor 2, 4, 6, 8, or 10 Beams avaiabe Up to 50ft (15m) range Simine design Laser-beam aignment Hooded Refective Photobeam Sensors 2, 4, 6, or 8 Beams avaiabe Up to 393ft (120m) range Muti-frequency Adjustabe interruption time Fush-Mount Photobeam Sensors Twin Photobeam Detectors Manua Avaiabe with 45ft (14m) or 35ft (11m) range Mounting hardware incuded Refector incuded Avaiabe with 50ft (15m) range or 33ft (10m) range Poarized version avaiabe Round refector incuded Avaiabe with refective beam and 16ft (5m) range or through-beam and 33ft (10m) range Adjustabe aignment ange Mounts to a singe-gang box WARRANTY: this SECO-LARM product is warranted against defects in materia and workmanship whie used in norma service for a period of one (1) year from the date of sae to the origina consumer customer. SECO-LARM s obigation is imited to the repair or repacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physica or eectrica misuse or abuse, negect, repair, or ateration, improper or abnorma usage, or fauty instaation, or if for any other reason SECO-LARM determines that such equipment is not operating propery as a resut of causes other than defects in materia and workmanship. The soe obigation of SECO-LARM, and the purchaser s excusive remedy, sha be imited to repacement or repair ony, at SECO-LARM s option. In no event sha SECO-LARM be iabe for any specia, coatera, incidenta, or consequentia persona or property damages of any kind to the purchaser or anyone ese. NOTICE: The information and specifications printed in this manua are current at the time of pubication. However, the SECO-LARM poicy is one of continua deveopment and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is aso not responsibe for misprints or typographica errors. Copyright 2013 SECO-LARM U.S.A., Inc. A rights reserved. This materia may not be reproduced or copied, in whoe or in part, without the written permission of SECO-LARM. Mode # Outdoor Range Indoor Range E-964-D390Q* 390 ft. (120m) 790 ft. (240m) E-960-D290Q 290 ft. (90m) 590 ft. (180m) E-960-D190Q 190 ft. (60m) 390 ft. (120m) E-960-D90Q 90 ft. (30m) 190 ft. (60m) * Muti-frequency version SECO-LARM U.S.A., Inc Miikan Avenue, Irvine, CA Te: / Fax: PITSW3 fie:dtp\manua\mie96x-dxxxq_p1305.pmd Website: E-mai: saes@seco-arm.com SECO-LARM Note: Products with mode numbers that end with "Q" or that have a round green"q"sticker are RoHS compiant.

2 TABLE OF CTENTS Important... 2 Choosing a Location... 3 Typica Instaations... 4 Running the Cabe... 4 Wiring the Wa Mount... 4 Wiring the Poe Mount... 5 Wiring... 5 Exampes of Ways To Connect Sensors... 6 Seectabe 4-channe Beam Frequency... 7 Features: Four seectabe beam frequencies (For E-964-D390Q mode ony). Twin beams provide reiabe perimeter security, minimizing fase aarms from faing eaves, birds, etc. Lensed optics reinforce beam strength and provide exceent immunity to fase aarms due to rain, snow, mist, etc. Weatherproof, sunight-fitering case for indoor and outdoor use. Non-poarized power inputs. Incuded: x 1 x 1 Mounting pates x 2 Beam Frequency Seection Chart... 7 (E-964-D390Q Mode Ony) Mutipe Sensors Sampe Appications Adjusting the Aignment... 9 Adjusting the Deay Time Testing the Unit Specifications Dimensions Troubeshooting Automaticay adjusts beam strength to compensate for different weather conditions Automatic input power fitering with specia noise rejection circuitry. N.C./N.O. aarm output. N.C. tamper circuit incuded. Quick, easy instaation with buit-in aser beam aignment system. Interruption time adjustabe for neary a situations. Poe mounting brackets (2 sets) Mounting hardware aso incuded. Fig. 12: Dimensions 43ST Poe Size Situation Upper View Side View Tabe 6: Troubeshooting LED does not ight. LED never ights up when the beam is interrupted. Beams interrupted and LED ights, but no aarm trigger. Aarm LED continuousy it. Aarm trigger becomes erratic in bad weather. Frequent fase triggers from eaves, birds, etc. 2.8 (72mm) Possibe Probem 6.8 (173mm) 2.9 (74mm) Front View Incorrecty wired and/or insufficient votage a. Insufficient votage b. Beam refected away from receiver c. Beams not simutaneousy interrupted. Aarm trigger cabe may be cut, or the reay contact stuck due to overoading. a. Lenses out of aignment. b. Beams are bocked. c. Cover is foggy or dirty. Lenses out of aignment. a. Too sensitive. b. Bad ocation. Soution Rear View Ensure the power suppy to the transmitter is 12 to 24 VAC/VDC. a. Doube-check the votage. b. Cean the cover. c. Check overa instaation. Check the continuity of the wiring between the sensor and the aarm. a. Reaign the enses. b. Remove any obstaces. c. Cean the cover. Check overa system instaation. If sti erratic, reaign the enses. a. Reduce the response time. b. Change the transmitter and/or ocation. IMPORTANT the Do not connect to power unti the sensor is competey instaed and instaation has been doube-checked. 2 11

3 Adjusting the Deay Time 1. The deay time adjustment knob sets how ong the beam can be interrupted before triggering the aarm (see fig. 11): a. A short interrupt time (high sensitivity) is suitabe for catching fast moving intruders, but more susceptibe to fase aarms. b. A ong interrupt time (ow sensitivity) reduces fase aarms, but fast moving intruders may not trigger the sensor. 2. Adjust the knob to the site s situation. You may need to make adjustments ater after the wak-through test. Testing the Unit 1. Power up the transmitter and receiver. 2. If the yeow or red LED remains steady even when the beam is not interrupted, re-adjust the aignment. 3. Wak between the transmitter and receiver to interrupt the beams. Wak at various speeds, and adjust the deay time adjustment knob as needed. Tabe 5: Specifications Mode Max. range (outdoor) Max. range (indoor) Max. current ( & ) 64mA No. of beam channe Votage output (+/-10%) Power Detection method Interrupt speed* Aarm output Tamper output ( & ) Aarm LED (receiver) Signa LED (receiver) Power LED ( & ) Laser waveength Laser output power Aignment ange Operating temperature Weight Case E-960-D90Q 90 (30m) 190 (60m) Fig. 11: Adjusting the Deay Time 300ms 50ms 700ms NOTE The aarm wi be triggered ony if both the upper and ower beams are simutaneousy interrupted. IMPORTANT Test the detector periodicay to ensure the aignment and deay time settings are suitabe for the site. E-960-D190Q 190 (60m) 390 (120m) E-960-D290Q 290 (90m) 590 (180m) E-964-D390Q 390 (120m) 790 (240m) 70mA 74mA 88mA N/A N/A N/A 4 1~4V 10~30 VAC/VDC (non-poarized) Simutaneous breaking of 2 beams 50msec~700msec (variabe) NO/NC reay, 120VAC, min. 1 sec. NC switch, 120VAC Red LED - : When transmitter and receiver are not aigned or when beam is broken. Yeow LED - : When receiver's signa is weak or when beam is broken. Green LED : Indicates connected to power 650nm 5mW Horizonta: ±90 0, Vertica: ± F (-25 0 C) to F (+55 0 C) 2.5 bs. (1.1kg) PC Resin Fig. 1: Identifying the Sensors Terminas Mounting Pate Signa LED Aarm LED Frequency seection* switch Choose a Location To prevent erratic operation and/or fase aarms: Wind wi not directy cause fase aarms, but coud cause eaves or simiar objects to fy or wave into the beams. Therefore, do not mount near trees, bushes, or other eafy vegetation. Do not mount where the transmitter or receiver coud be spashed by water or mud. Do not mount where the unit coud be suddeny exposed to a bright ight, such as a foodight or a passing automobie s headight. Do not et sunight or any direct beam of ight enter the sensing spot of the transmitter. If needed, mount so the receiver, not the transmitter, faces the sun. Do not mount where animas coud break the beams. Fig. 2: Vertica and Horizonta Adjustments ±5 (10 ) Power LED Votage output probes * For muti-frequency E-964-D390Q mode ony. Vertica adjustment Horizonta adjustment Vertica adjustment screw Frequency seection* switch Deay time adjustment knob Power LED Vertica adjustment screw Horizonta adjustment Lens View finder Aignment aser Laser / switch Fig. 3:Typica Instaations Side Views 32" to 39" Top Views *This is the minimum time interva between breaking of both beams which wi trigger the output. Setting the interva onger wi reduce fase aarms from birds or faing eaves, etc., whie setting it shorter wi detect faster moving objects. 10 ±90 (180 ) 3

4 Typica Instaations The photoeectric beam ens can be adjusted horizontay ±90, and verticay ±5 (see fig. 2). This aows much fexibiity in terms of how the transmitter and receiver can be mounted. See fig. 3. Insta at a distance of 32 to 39 (80 to 100 cm) above the ground for most situations. See fig. 3. Running the Cabe Run a cabe from the aarm contro pane to the photobeam sensor. If burying the cabe is required, make sure to use eectrica conduit. Shieded cabe is strongy suggested. See Tabe 1 for maximum cabe ength. Tabe 1: Cabe Length Mode E-960-D90Q E-960-D190Q E-960-D290Q Wire Size 12V 24V 12V 24V 12V 24V 12V 24V AWG22 320m 2,800m 280m 2,400m 200m 1,600m 110m 0.33mm in 1,050 ft. 2 18,000 ft. 920 ft. 7,870 ft. 660 ft. 5,250 ft. 390 ft. AWG20 550m 4,800m 450m 4,200m 350m 3,000m 170m 0.52mm 2 1,800 ft in 2 15,750 ft. 1,480 ft. 13,780 ft. 1,150 ft. 9,840 ft. 560 ft. AWG18 800m 7,200m 700m 6,200m 500m 4,200m 250m 0.83mm 2 2,600 ft. 23,620 ft. 2,300 ft. 20,340 ft. 1,640 ft. 13,780 ft. 820 ft in 2 AWG17 980m 8,800m 850m 7,600m 590m 5,200m 310m 1.03mm 2 3,190 ft. 28,870 ft. 2,790 ft. 24,930 ft. 1,940 ft. 17,060 ft. 1,020 ft in 2 Note (1): Max. cabe ength when two or more sets are connected is the vaue shown in Tabe 1 divided by the number of sets. Note (2): The power ine can be wired to a distance of up to 3,300 ft. (1,000m) with AWG22 (0.33mm 2 ) teephone wire. Wiring the Wa Mount 1. Remove the cover. Remove the screw under the ens unit in order to detach the mounting pate. See fig If the sensor wiring comes from inside the wa Break a hoe in the mounting pate s rubber grommet, and pu the cabe through the grommet s hoe. Then run the cabe through the hoe near the top of the sensor unit so it comes out the front. Using two of the incuded mounting screws, attach the mounting pate to the wa. Then reattach the sensor unit to the mounting pate, connect the wires, and snap on the cover. See fig E-964-D390Q 900m 2,950 ft. 1,400m 4,590 ft. 2,200m 7,220 ft. 2,600m 8,530 ft. 3. If the sensor wiring is run aong the surface of the wa There are two pastic knockouts on the back of the sensor unit, one on top and one on bottom. Break out the appropriate knockout, and pu the wiring through the knockout. Then run the wiring through the hoe near the top of the sensor unit so it comes out the front. Using two of the incuded mounting screws, attach the mounting pate to the wa. Then reattach the sensor unit to the mounting pate, connect the wires, and snap on the cover. See fig. 6. Adjusting the Aignment The transmitter and receiver sensor units can be adjusted ±5º verticay and ±90º horizontay once the unit is mounted and power is connected (see fig. 2 on page 3). There are two ways to adjust aignment: 1. Laser adjustment (see fig. 1 on page 3): a. Remove the transmitter cover, then turn the aser on with the / switch (see fig. 1 on page 3). A red dot wi show where the photoeectric beams are aimed. b. Adjust the transmitter's sensor unit verticay and horizontay unti the red dot is centered on the receiver and both the receiver s LEDs turn off. See Tabe 3. It may be necessary to adjust the horizonta and vertica ange of the receiver's sensor unit as we. c. Repeat steps a and b for the receiver. d. Turn the asers off, and then repace the covers. WARNING: Do not ook directy at the asers. 2. Eyeba adjustment (see fig.10): a. Remove the transmitter cover, and ook into one of the aignment viewfinders (one of the four hoes ocated between the two enses) at a 45 ange. b. Adjust the horizonta ange of the ens verticay and horizontay unti the receiver is ceary seen in the viewfinder. c. Repeat steps a and b for the receiver. Fine Tuning the 1. aigned, Once the the sensor sensor is mounted can be fine and tuned using the votage output jack. a. Set the range of a vot-ohm meter (VOM) to 1~4VDC. b. Insert the red (+) probe into the (+) termina and the back (-) probe into the (-) termina. c. Measure the votage (see tabe 4). d. Adjust the horizonta ange by hand unti the VOM indicates the highest votage. e. Adjust the vertica ange by turning the vertica adjustment screw unti the VOM indicates the highest votage. NOTE - Do not interrupt the beam whie adjusting aignment. 9 Fig. 10: Horizonta and Vertica Sensor Adjustment Vertica Adjustment Horizonta Adjustment View Finders Tabe 3: LED Indicators Aarm (Red LED) d. Repace the transmitter and receiver covers. NOTE - If you cannot see the opposite unit in the viewfinder, put a sheet of white paper near the unit to be seen, move your eyes about 2" (5cm) away from the viewfinder, and try again. Tabe 4: Votage output >2.8V 2.0~2.7V 1.2~1.9V <1.1V Signa (Yeow LED) Muti frequency Fash Aignment quaity Best Good Fair Re-adjust Note: 4VDC is maximum possibe reading. Signa strength Best Good Fair Re-adjust

5 3. Two ayer (doube stacked) appications. Sensor #1 Sensor #2 Sensor #3 4. Perimeter security appication. Sensor #4 Sensor #5 Sensor #6 Wiring the Poe Mount (NOTE Poe mounting bracket required.) 1. Remove the cover. Remove the screw under the ens unit in order to detach the mounting pate. See fig Break a hoe in the mounting pate s rubber grommet, and pu the cabe through the grommet s hoe. Then run the cabe through the hoe near the top of the sensor unit so it comes out the front. Use the incuded mounting bracket to mount to the poe. Then reattach the sensor unit to the mounting pate, connect the wires, and snap on the cover. See fig. 7. Wiring (fig. 8) 1. Screw the wires tighty to avoid sipping off the terminas, but not so tight that they break. 2. Screws on terminas which are not used shoud be tightened. 3. Grounding may be necessary, depending on the ocation. Fig. 4: Remove the cover Fig. 5: Wa Mount, Wire from Inside Wa Sensor #3 Sensor #2 Sensor #1 Sensor #4 5. Two ayer (doube stacked) perimeter security appication. Fig. 6: Wa Mount, Wire Runs Aong Wa Fig. 7: Poe Mount or Fig. 8: Wiring ~30 AC/DC Power 10~ 30 VAC/VDC (non-poarized) N.C. Tamper output N.C. switch 120V (AC/DC) 1A (Triggers if cover detached) 10~30 AC/DC COM. N.C. Power 10~ 30 VAC/VDC (non-poarized) Aarm output 120V (AC/DC) 1A N.O. N.C. Tamper output N.C. switch 120V (AC/DC) 1A (Triggers if cover detached) 8 5

6 Fig. 9: Exampes of Possibe Ways To Connect One or More Sensors Exampe connection 1 - Standard ÂÃ Contro pane (12VDC) }Aarm signa Seectabe 4-channe beam frequency (For E-964-D390Q mode ony) The sensor beam frequency can be set at different eves on-site to avoid interference from other twin photobeam sensors nearby. Usefu during mutipe sensor appications as shown beow. To seect between four different beam frequencies, adjust the beam channe switch of the transmitter side and receiver side. See fig. 1 for switch ocation and tabe 2 for switch position. Important The transmitter and receiver sensor pair must be set with the same frequency. Exampe connection 2 - Dua Sensors, Separate Channes ÂÃ ÂÃ Contro pane (12VDC) }Aarm (ch. 1) }Aarm (ch. 2) Tabe 2: Beam Frequency Seection Chart (For E-964-D390Q mode ony) Frequency channe CH1 CH2 CH3 CH4 Switch position NO NO NO NO Mutipe sensor sampe appications ( For E-964-D390Q mode ony) 1. Singe pair mutipe ayer appication. Exampe connection 3 - In-ine Singe Channe Contro pane (12VDC) }Aarm signa Sensor #1 Sensor #2 ÂÃ ÂÃ Sensor #3 Sensor #4 Exampe connection 4 - Two stacked }Aarm signa 2. Long distance series appication. Sensor #1 Sensor #2 Sensor #3 Sensor #4 ÂÃ ÂÃ 6 7