Sentinel XT Clear Hood and Full Hood PAPR System

Transcription

1 Sentinel XT Clear Hood and Full Hood PAPR System 1

2 Features NIOSH approved with HEPA and OV/AG/HE Filters Greater than 8 to 8.5 SCFM (230 to 240 LPM) airflow Integrated blower and battery with audible and visible alarms Li Polymer (Li PO) battery reduces weight (2.2 # for Battery and Blower) and extends operation time (12 hours) Panoramic visor provides 320 o field of view No uncomfortable suspension or neck dam Secure hood with clips on outer bib Allows use of personal safety equipment Easily deconable comfort belt or back harness 2

3 Safety Through the Entire Range of Pharma Processes Stores Bulk Production QA Dosage Manufacturing 3

4 Comfort Belt Style Components Charger & Charging Cradle Integrated Blower & Li Po Battery HEPA Filters Breathing Tubes (33 or 25 supplied with system) Comfort Belt Not shown: Sentinel XT Clear Hood, Flow Meter 4

5 Back Harness Style Components Charger & Charging Cradle Integrated Blower & Li Po Battery HEPA Filters Breathing Tubes (33 or 25 supplied with system) Back Harness Not shown: Sentinel XT Clear Hood, Flow Meter 5

6 Comfort Belt and Back Harness View Integrated PAPR and Battery 2. Breathing Tube 6

7 Blower System On/Off Switch Cover Rolled threads on filter element and Breathing Tube attachments Integrated blower and Li Polymer battery Visible Filters, removed without touching contaminated filter element or internal blower housing Battery Life Gauge 7

8 High Efficiency Particulate Air (HEPA) Filters Passed NIOSH Silica Dust testing Filters Screw in and out Make sure bottom, blower plug is in place when using HEPA Filters (not used with OV/AG/HE filter) Remove filter plug before using 8

9 OV/AG/HE Filters NIOSH approved for use with OV/CD/CL/HC/HF/SD/HE filters Note: Yellow and Purple label indicates safe to use in the following environments: OV Organic Vapor CD Chlorine Dioxide CL Chlorine HC Hydrogen Chloride HF Hydrogen Fluoride SD Sulfur Dioxide HE High Efficiency Particulate Air 9

10 Battery Pack Replacement Open battery pack compartment and remove battery Connect new battery 10

11 Deconable Comfort Belt Deconable belt 2. Blower connection clips 3. Snap in place buckle 4. Belt keepers 1 11

12 Optional Deconable Back Harness Deconable shoulder straps 2. Deconable back plate 3. Deconable back support belt 4. Blower connection clips (same as Comfort Belt) 3 Not approved with Full Hood 2 12

13 Optional Breathing Tube Cover Slip Breathing Tube Cover (S-3102) onto open end of the Installation Tool (p/n ) Slide Breathing Tube into cover and pull through Attach to Blower and Hood as normal 13

14 Optional Blower Cover Slide Blower Cover (S-3103) over blower Align Breathing Tube outlet and filter ports with openings on cover Attach filters, Breathing Tube, Comfort Belt (or optional Back Harness) as normal 14

15 Battery Charging LiPolymer Battery Pack Plug the battery charger to the battery cradle Connect the battery charger to an electrical outlet Battery Charging Cradle Slide the battery in place so contacts are touching Charge the battery for approximately 5 hours Charger Note: as with any Li Ion or Li Polymer battery, take caution not to allow extraneous metal to touch both contacts at the same time. 15

16 Checking the airflow Place the flow meter in the blower s hood connector. Keep the flow meter vertical. Flow Meter The position of the upper (flat surface) black cone in the flow meter should be above the indication line. If any part of the upper (flat surface) of the black cone is below the line on the flow meter, check for: Blower malfunction Improperly installed, clogged or damaged cartridge(s) Low battery charge or battery malfunction Improperly seated filter gasket(s) Indication line close up 16

17 Connect the Breathing Tube The threaded ends of the Breathing Tube are the same on both sides Screw the end of the breathing tube into the blower unit until it is hand tight. DO NOT OVER TIGHTEN 17

18 Connect the Breathing Tube to the Hood Screw the opposite end of the breathing tube into the Clear Hood until it is hand tight. DO NOT OVER TIGHTEN 18

19 Donning and Securing the Clear Hood Turn on the blower and don the blower and the hood Tuck in the inner bib (one) Attach clips to Tyveks or cloth garment NOTE: keep the coverall loose or go up one size for best attachment 19

20 Cleaning Decontamination Solution Lysol Brand I.C. Quaternary Disinfectant Cleaner Lysol Brand All Purpose Disinfectant Cleaner Clorox Clean-Up Cleaner with Bleach Clidox -S (Chlorine Dioxide) PDI Sani-Cloth Plus (germicidal disposable cloth) Maximum Concentration Not to exceed ½ ounce per 1 gallon of water Not to exceed 8.5 ounces per 1 gallon of water May be used full strength 1:18:1 as a wipe down 1 part base, 18 parts water, 1 part activator Use cloth to thoroughly wet surface and let air dry. Treated surface must remain visibly wet for a full five (5) minutes. MKT-0003 Rev. C 20

21 Cleaning (cont) Solution Application and Limitations The decontamination solutions noted above may be applied via cloth, paper towels, or spraying methods. Never submerge or immerse any Sentinel XL PAPR blower, filter, hose, or hood components in liquid, as this may permanently damage the electronics, batteries, or affect hood or hose function. Wipe components dry with a soft cloth following decontamination and rinsing with clean water, unless noted to air dry. MKT-0003 Rev. C 21

22 Benefits Ultimate in Operator Safety and comfort Ergonomic design and wide field of view supports worker comfort and productivity Better weight distribution, comfort and elimination of snag hazards with a light weight, integrated PAPR 22

23 Alan George, PPE Specialist Ph: , extension 407 Cell: