PERFORMANCE SPECIFICATIONS

Transcription

1 Specifications 530T Series Electronic Gauge Pressure Transmitter With Remote Seal Elements Operates at Full Vacuum ±0.2% of span accuracy Spans from 10 psig to 2000 psig Outstanding temperature stability All-welded remote seal design 7-year warranty The 530T Series Remote Seal Electronic Gauge Pressure Transmitter is a two-wire, 24V dc transmitter with a 4 to 20 ma dc output signal linear to the input pressure. The transmitter employs a ceramic capacitance sensor and unique, hermetically sealed, thick-film hybrid circuit. Each hybrid circuit is dynamically laser trimmed to match the performance characteristics of the sensor to create a high-performance, high-reliability transmitter. Combined accuracy, temperature, and pressure stability are unmatched by other electronic pressure transmitters. SPANS AND RANGES Transmitter Span Limits Range Limits Maximum Working Minimum & Maximum Lower Upper Pressure (MWP)* 532T 10 psig to 40 psig psig 40 psig 120 psig (70 kpa) to (275 kpa) (-100 kpa) (275 kpa) (825 kpa) 533T 40 psig to 160 psig psig 160 psig 480 psig (275 kpa) to (1,100 kpa) (-100 kpa) (1,100 kpa) (3,300 kpa) 534T 150 psig to 600 psig psig 600 psig 1500 psig (1,050 kpa) to (4,200 kpa) (-100 kpa) (4,200 kpa) (10,000 kpa) 535T 500 psig to 2000 psig psig 2000 psig 2000 psig (3,500 kpa) to (14,000 kpa) (-100 kpa) (14,000 kpa) (14,000 kpa) * Overpressure Limit is that given or seal MWP, whichever is less. Zero Elevation/Suppression: Zero is infinitely adjustable provided that the calibrated range is within the span and range limits above. Warranty: ABB Instrumentation Inc., Rochester, NY, warrants the 500T Series Transmitter for 7 years from date of shipment. Contact ABB Instrumentation Inc., for complete information PERFORMANCE SPECIFICATIONS Electrical Classification Agency approvals and certifications as listed in Ordering Information. Also see Specification Sheet Temperature Limit Process Silicone 2 702A Fluid: -13 to 400 F (-25 to 204 C) Water/Glycerine: 20 to 200 F (-7 to 93 C) Silicone 702B Fluid: 20 to 600 F (-7 to 316 C) Ethylbenzene: 100 to 200 F (73 to 93 C) Fluorolube 3 : 0 to 250 F (-18 to 121 C) Ambient (Also, see 8 th character of ordering information) Without Digital Output Meter: -13 to 185 F (-25 to 85 C) With Digital Output Meter: -13 to 149 F (-25 to 65 C) Storage Without Digital Output Meter: -65 to max. ambient + 15 F (-54 to max. ambient C) With Digital Output Meter: -65 to 149 F (-54 to 65 C) Service Liquid, gas, or steam Vacuum Service Full Vacuum ABB Instrumentation SS T-169

2 Operating Voltage (Transmitter) Maximum Without Options With Surge Protection With Digital Output Meter With All Options Minimum Without Options With Surge Protection With Digital Output Meter With All Options Load Limitations* Drive Impedance Supply V dc - Minimum V dc Maximum Drive Impedance Without Options With Surge Protection With Digital Output Meter With All Options Relative Humidity 0 to 100% RH 12V dc 13.4V dc 16.0V dc 21.9V dc 1650 ohms 1580 ohms 1450 ohms 1150 ohms Remote Seal** Wafer Element For installation on 1-1/2 in., ANSI, raised face flange. MWP in lower of the overpressure limit or rating of back-up flange. Union Connection Element Without Fitting 1500 psig ( kpa) MWP or overpressure limit, whichever is less Union Connection Element With Welding Bushing 1500 psig ( kpa) MWP or overpressure limit, whichever is less Union Connection element With Chemical Tee Flange 300 psig (2000 kpa) MWP or overpressure limit, whichever is less Vavuum Service Full Vacuum * For higher load capability, contact Rochester. ** All elements have low-pressure limit of 0 psia (0 kpa abs) provided seal element is at or above level of capsule. See Note 2 after Ordering Information. All welded construction permits operation at full vacuum depending on installation and fill fluid. PERFORMANCE SPECIFICATIONS Accuracy (Includes effects of linearity, hysteresis, and repeatability) ±0.2% of calibrated span Hysteresis and Dead Band Combined Better than 0.05% Repeatability Better than 0.05% Ambient Temperature Effect Temperature effect on performance of remote seal transmitters is dependent on many factors such as: Process temperature Ambient temperature Sunshine vs shade on capillary length of capillary Type of seal element Capillary Fill fluid Calibrated span of unit Amount of suppression or elevation Under controlled conditions, temperature effect is less than 1.0% per 100 F (56 C) Overpressure Effect ±0.25% of upper range limit (URL) on zero Optional Surge Protection Up to 2500V pulse (5K amp discharge current) of 8µs rise time and 20 µs decay to half value Output Signal 4 to 20 ma dc Long-Term Stability Better than ±0.25% of URL after 6 months Supply Voltage Effect Less than 0.005% per V dc Load Effect None PHYSICAL SPECIFICATIONS Vibration Effect ±0.1% URL/2g at 15 to 150 Hz ±0.1% URL/g at 151 to 2000 Hz RFI Effect Meets SAMA Standard PMC Tested over a full frequency range of 20 to 1000 MHz. Process Diaphragm Choice of: Type 316L SST Hastelloy C 4 alloy Tantalum (available with Wafer Seal Element only) Fill Fluids Primary Silicone 1 Seal and Capillary Choice of: Silicone 702A Fluorolube 2 Silicone 702B Water/Glycerine Ethylbenzene Capillary 304 SST capillary with spiral armor protection and polyethylene jacket Transmitter Housing Low copper cast aluminum with baked epoxy ester, urea formaldehyde melamine finish; NEMA 4X, CSA Enc 4, IP66 NACE (National Association of Corrosion Engineers) Interpretation of NACE Specification MR-01-75, latest Revision, is that it applies only to process-wetted parts. NACE qualified selections are clearly identified under Ordering Information. Weight Basic Transmitter: 6.1 lb (2.8 kg) Seal Elements: Add 1.5 to 5.9 lb. (0.7 to 2.7 kg) Electrical Connection 1/2 in. Int. NPT For Electrical Codes 08 and 38 only, 2 each, 1/2 in. NPT male x M20 female adapters are provided. For Electrical Code 82 only, 2 each environment-resistant circular connectors with angle plug, per MIL-C-5015, are provided. SS T-170

3 SS T-171

4 ORDERING INFORMATION 530T SERIES ELECTRONIC GAUGE PRESSURE TRANSMITTER WITH REMOTE SEAL ELEMENTS 1. Select one character or set of characters from each category and specify complete catalog number per sample below. 2. Specify tagging if required. Tagging information is provided on the exterior stainless steel data plate to a limit of 40 characters. 3. Specify calibration in psi or kpa. Code No. 532T 533T 534T 535T Description BASE NUMBER - 1st thru 4th characters Electronic Gauge Pressure Transmitter with Remote Seal Elements, Span adjustable from 10 to 40 psi (70 to 275 kpa) Electronic Gauge Pressure Transmitter with Remote Seal Elements, Span adjustable from 40 to 160 psi (275 to kpa) Electronic Gauge Pressure Transmitter with Remote Seal Elements, Span adjustable from 150 to 600 psi (1 050 to kpa) Electronic Gauge Pressure Transmitter with Remote Seal Elements, Span adjustable from 500 to 2000 psi (3 500 to kpa) PRIMARY FILL-FLUID - 5th character D Silicone 1 ELECTRICAL CODE - 6th and 7th characters (also see Specification Sheet 12-16) 01 FM Approved: Non-Incendive (Division 2), Explosionproof (Division 1), Intrinsic Safety (Division 1) 02 BASEEFA Certified: Type N (Zone 2), Intrinsic Safety (Zone 0) 04 CSA Certified: Non-Incendive (Division 2), Explosionproof (Division 1), Intrinsic Safety (Division 1) 08 SAA Certified: Type N (Zone 2), Flameproof (Zone 1), Intrinsic Safety (Zone 0) 10 General Purpose, ABB Instrumentation Standard 31 FM Approved: Non-Incendive (Division 2), Explosionproof (Division 1) (Note 1) 32 BASEEFA Certified: Type N (Zone 2) (Note 1) 34 CSA Certified: Non-Incendive (Division 2), Explosionproof (Division 1) (Note 1) 38 SAA Certified: Type N (Zone 2), Flameproof (Zone 1) (Note 1) 45 BASEEFA Certified: Flameproof (Zone 1) 82 BASEEFA Certified: Intrinsic Safety (Zone 0) (Electrical Connection includes Environment Resistant Circular Connector with Angle Plug per MIL-C-5015) CAPILLARY FILL-FLUID AND SEAL ELEMENT TEMPERATURE RANGES - 8th character 1 Silicone 702A; Process: -13 to 400 F (-25 to 204 C) (Note 2); Ambient: 10 to 135 F (-12 to 57 C) (Note 5) 2 Water/Glycerine; Process: 20 to 200 F (-7 to 93 C) (Note 3); Ambient: 20 to 185 F (-7 to 85 C) 3 Silicone 702B (not available with 18 th character 1); Process: 20 to 600 F (-7 to 316 C) (Note 2); Ambient: 20 to 120 F (-7 to 49 C) (Note 5) 4 Ethylbenzene; Process: -100 to 200 F (-73 to 93 C) (Note 3); Ambient: 20 to 125 F (-7 to 52 C) (Note 5) 5 Fluorolube 2 ; Process: 20 to 250 F (-7 to 121 C) (Note 2); Ambient: 15 to 145 F (-9 to 63 C) (Note 5) SEAL ELEMENT TYPE AND MAXIMUM WORKING PRESSURE (MWP) - 9th character (MWP is lower of Seal Element or Transmitter Span MWP limitations) 1 Wafer Element for Installation on 1-1/2 in. ANSI Raised Face Flange, 2000 psig ( kpa) MWP 5 Union Connection Element without Fitting, 1500 psig ( kpa) MWP (only available with 533T, 534T), maximum 500 F (260 C) 6 Union Connection element with 316 SST Welded Bushing, 1500 psig ( kpa) MWP (only available with 533T, 534T), maximum 500 F (260 C) 7 Union Connection Element with Chemical Tee Flange, 300 psig (2000 kpa) MWP (only available with 533T), maximum 500 F (260 C) SEAL ELEMENT DIAPHRAGM MATERIAL - 10th character 2 Type 316L SST - NACE (not available with Element O-Ring Selection 1) 3 Hastelloy C 7 Tantalum (only available with Seal Element Type 1), maximum 260 C ( 500 F) B MODEL - 11th character Design level 0 UNUSED CHARACTER - 12th character MOUNTING BRACKET - 13th character 1 Bracket for 1-1/4 in. to 2 in. (32 mm to 50 mm) pipe or surface mounting, carbon steel 2 Bracket for 1-1/4 in. to 2 in. (32 mm to 50 mm) pipe or surface mounting, SST (Note 4) SS T-172

5 ORDERING INFORMATION Code No. Description OUTPUT METER - 14th character 1 0 to 100 Linear Scale 3 Digital (see Note 1) OPTIONS - 15th character 2 Surge Protector - HYPHEN - 16th character WAFER ELEMENT BACKUP FLANGE (For use with Wafer Seal Element) - 17th character 1 One 1-1/2 in. ANSI, Class 150, Carbon Steel, Raised Face, Backup Flange with Bolts and Nuts (275 psi at 100 F) (not available on 535T) 2 One 1-1/2 in. ANSI, Class 300, Carbon Steel, Raised Face, Backup Flange with Bolts and Nuts (720 psi at 100 F) 3 One 1-1/2 in. ANSI, Class 1500, Carbon Steel, Raised Face, Backup Flange with Bolts and Nuts (3600 psi at 100 F) UNION CONNECTION ELEMENT O-RING - 18th character (not available with Seal Element Selection 5, 6, or 7) 1 Silicone Rubber (available with Seal Element Selection 5, 6, or 7 only, NOT available with 8 th character 3 or 10 th character 2), maximum 400 F (204 C) 2 Teflon 3 TFE (available with Seal Element Selection 5, 6, or 7 only), maximum 500 F (260 C) CAPILLARY LENGTH - 19th and 20th characters 05 5 ft (1.5m) minimum ft (3m) ft (4.5m) ft (6m) maximum 534TD01112B SAMPLE CATALOG NUMBER NOTES: 1. Electrical Codes 10, 31, 32, 34, 38 and 45 are the only valid codes when a digital output meter (14th character 3) is required. 2. Maximum temperature for full vacuum limit is: 300 F (149 C) for Silicone 702A 350 F (177 C) for Silicone 702B 175 F (80 C) for Fluorolube Consult ABB Instrumentation Rochester for low-pressure limits at higher temperatures. 3. Not for vacuum service. Consult ABB Instrumentation Rochester for low pressure limits. 4. Not available with BASEEFA or SAA electrical code. 5. Listed ambient temperature limits are for maximum capillary length of 20 feet (6m). For shorter capillary length, decrease the minimum and increase the maximum ambient by 1 F (0.55 C) for each foot (each meter x 3.28) below 20 feet (6m). Notes: Minimum ambient can not be less than minimum process. Does NOT apply to water/glycerine. For example, ambient temperature limits for a 5ft (1.5m) capillary length with Silicone 702A are: minimum ambient = 10 F 1 F x 15 ft = 5 F = 12 C (0.55 C x 4.5m x 3.28) = 20 C maximum ambient = 135 F + 1 F x 15 ft = 150 F = 57 C + (0.55 C x 4.5m x 3.28) = 65 C 1 Trademark of Dow Corning Company 2 Trademark of Occidental Chemical Company 3 Trademark of E.I. du Pont de Nemours & Company, Inc. 4 Trademark of Haynes International Inc. SS T-173

6 The Company s policy is one of continuous product improvement and the right is reserved to modify specifications contained herein without notice ABB Instrumentation ABB Kent-Taylor Ltd. ABB Instrumentation Inc. ABB Kent-Taylor SpA St. Neots Cambs. P.O. Box Lenno England, PE19 3EU Rochester, New York Como, Italy Tel: (01480) Tel: (716) Tel: (0344) Fax: (01480) Fax: (716) Fax: (0344) SS T-174 SS