5-Alloy Systems & Phase Diagrams

Size: px
Start display at page:

Download "5-Alloy Systems & Phase Diagrams"

Transcription

1 5-Alloy Systems & Phase Diagrams 5-1-Utility & Limitations to Use of Phase Diagrams Utility Phase Transformation Welding & Casting Soldering & Brazing Electromigration & Diffusion Problems Limitations Phase Diagrams are also known as Equilibrium Diagrams Rate of Transformation is missing TTT (Time-Temperature-Transformation) Kirkendahl Voiding Corrosion Electrical Resistivity 5-2- Concepts Phase A phase is a homogenous, physically distinct and mechanically separable portion of the material with a given chemical composition and structure. For solids: Chemically and structurally distinct For liquids: Miscibility For gases: Always 1 phase Metals and Alloys A pure metal solidifies at a constant temperature equal to its freezing point (same as melting point) Dr Ali Salami Golezani Page 1

2 Components Pure metals and/or compounds of which a system is made up, ie: Brass has the components Cu and Zn. Or Ceramic systems normally have compound components ie SiO 2 and Al 2 O 3 Solubility 1. Total solubility (miscibility), ie alcohol+water(one phase) 2. Total immiscibility, ie water+sand(two phases) 3. Limited solubility, ie salt, or sugar+water, A certain amount of salt, or sugar, will dissolve Unsaturated Saturated Supersaturated Metallic Solution Most, but not all, metals will mix completely in the liquid phase. When they freeze the solids that they form can have different forms. These are solid solutions, inter-metallic compounds and intermediate phases. Similar behavior is found in ceramic systems. a) Solid Solutions A solid solution is formed when the impurity atoms mix with the host atoms in the solid without hange of crystal structure. There are two types: Substitutional S.S The substitutional atoms replace atoms of the solvent. Small atoms (C N) can fit in the holes in the solute lattice. Interstitial S.S The interstitial atom fits into the spaces in the solute lattice. Hume Rothery Rules Structure: crystal structure-must be the same Size: The atoms sizes should not differ by more than 15%. Electronegativity: The atoms should have similar electronegativity, or Elements should not form compounds with each other Valence: Elements should have the same valence. Dr Ali Salami Golezani Page 2

3 b) Intermediate Phases When two metals have widely divergent electrochemical properties they are likely to associate to form a chemical compound. Thus strongly electropositive magnesium will combine with weakly electropositive tin to form the substance Mg 2 Sn. This is generally described as an intermetallic compound. Between these two extremes of substitutional solid solution on the one hand and intermetallic compound on the other, phases are formed which exhibit a gradation of properties according to the degree of association which occurs between the atoms taking part. These phases are collectively termed intermediate phases. At one extreme we have true intermetallic compounds whilst at the other ordered structures which can be more accurately classed as secondary solid solutions. These intermediate phases can be classified into three main groups: 1 Intermetallic compounds in which the laws of chemical valence are apparently obeyed as in Mg2Sn, Mg2Pb, Mg3Sb2 and Mg3Bi2. These valence compounds are generally formed when one metal (such as mag-nesium) has chemical properties which are strongly metallic, and the other metal (such as antimony, tin or bismuth) chemical properties which are only weakly metallic and, in fact, bordering on those of non-metals. Frequently such a compound has a melting point which is higher than that of either of the parent metals. For example, the intermetallic compound Mg2Sn melts at 7800C, whereas the parent metals magnesium and tin melt at 650 and 232 C respectively. This is an indication of the high strength of the chemical bond in Mg2Sn. 2 Electron Compounds the chemical valence of a metal is a function of the number of electrons in the outer 'shell' of the atom, whilst the nature of the metallic bond is such that wholesale sharing of umbers of electrons takes place in the crystal structure of a pure metal. In these 'electron compounds' the normal valence laws are not obeyed, but in many instances there is a fixed ratio between the total number of valence bonds of all the atoms involved and the total number of atoms in the empirical formula of the compound in question. There are three such ratios, commonly referred to as Hume-Rothery ratios: (i) Ratio 3/2 (21/14) (3 structures, such as CuZn, Cu3Al, Cu5Sn, Ag3Al, etc. (ii) Ratio 21/13 y structures, such as Cu5Zn8, G 19 Al 4, Ag5Zn8, Na3iPb8, etc. (iii) Ratio 7/4 (21/12) e structures, such as CuZn3, Cu3Sn, AgCd3, Ag5Al3, etc. Size-factor Compounds These are intermediate phases in which compositions and crystal structures arrange themselves in such a way as to allow the constituent atoms to pack themselves closely together. In the Laves phases compositions are based upon the general formula AB2, eg MgNi2, MgCu2, TiCr2 and MnBe2. Their formation depends upon the fact that the constituent atoms vary in size by about 22.5% but that they can none the less pack closely together in crystal structures. A very important group of size-factor compounds are the interstitial compounds formed between some transition metals and certain small nonmetallic atoms. When the solid solubility of an interstitially dissolved element is exceeded a compound is precipitated from the solid solution. In this type of compound the small non-metal atoms still occupy interstitial positions but the overall crystal structure of the compound is different from that of the original interstitial solid solution. Compounds of this type have metallic properties and comprise hydrides, nitrides, borides and carbides of which TiH2, TiN, Mn2N, TiB2, TaC, W2C, WC, Mo 2 C and Fe3C are typical. All of these compounds are extremely hard and the carbides find application in tool steels and cemented-carbide cutting materials. Fe3C is of course the phase cementite of ordinary carbon steels. Many of these carbides are extremely refractory, having melting points well in excess of 3000 o C. Dr Ali Salami Golezani Page 3

4 Note: T m Comparison: Understanding interactions on bond energies Interaction between 2 species: A and B Thermodynamic Parameter: Melting Point (T) How does mixing of A-A and B-B bonds affect T? The Ideal Case (S.S) Eutectic Behavior Intermetallic CompoundFormation (A-B) = x(a-a) + (1-x) (B-B) Where x is the mole fraction of A in B T Alloy = T A + x ( T B -T A ) A-B < 0.5 (A-A + B-B) T Alloy < T A, T B A-B > 0.5 (A-A + B-B) T Alloy > T A, T B Examples: Copper Nickel, Silicon Germanium Examples: Lead-Tin, Gold-Silicon Example: Gallium-Arsenic 5-3-Unary or One Component Phase Diagram The simplest case-water, Also known as a P-T diagram and Sign of [dp/dt] for: Solid-Liquid, Liquid-Gas and Gas-Solid equilibrium. P-T Diagram for Water α-quartz β-quartz β-tridymite β-cristobalite liquid 5-4-Binary System or Binary Diagram If we consider the binary A-B system and add a second axis for composition, the behavior illustrated in Fig. A is commonly observed. A phase diagram (or equilibrium diagram) is a diagram with T and composition as axes, showing the equilibrium constitution. Dr Ali Salami Golezani Page 4

5 Composition Presentation Mol (n) Weight % (Wt%) Atom (or Mol) % (at%) n=(m/m) Wt% A =(weight of component A/Σ weights of all components) 100 X A =(number of atoms (or mols) of component A/Σ number of atoms (or mols) of all components) 100 The Phase Rule or Phase Equilibrium It refers to the set of conditions where more than one phase may exist. It can be reflected by constancy with time in the phase characteristics of a system. 1. Phase rule: P+F=C+2 2. Condensed Phase Rule: P+F = C+1 P: number of phase, (e.g. Polymorphism, solid solution) F: number of degrees of freedom (temperature, pressure and composition of phases) C: number of components (minimum number of constituents in composition) Working with Phase Diagrams 1. Overall Composition 2. Solidus Temperature at which alloy is completely solid or Temperature at which liquefaction begins 3. Liquidus Temperature at which alloy is completely liquid or Temperature at which solidification begins 4. Limits of Solid Solubility Unlimited Solid Solubility: Solute and solvent are mutually soluble at all concentrations, e.g., Cu-Ni system Meets the requirements of the Hume- Rothery Rules Result is a single phase alloy Limited or Partial Solid Solubility: There is a limit to how much of the solute can dissolve in the solvent before saturation is reached, e.g., Pb-Sn and most other systems Does not meet the requirements of the Hume-Rothery Rules Results in a multi-phase alloy 5. Chemical Composition of Phases at any temperature It is the chemical composition of each phase in the system In a system having more than one phase, each phase will have a unique chemical composition which will be different from each other, and will also be different from the overall composition 6. Amount of Phases at any temperature Level rule: relative amounts of two phases in a mixture 7. Invariant Reactions Eutectic: L = α (s) + β (s) ; e.g., Pb-Sn Peritectic: α (s) + L = β (s) ; e.g., Pb-In Monotectic: L 1 = α (s) + L 2 ; e.g., Cu-Pb Syntectic: L 1 + L 2 = α (s) ; e.g., Na-Zn Metatectic: β (s) + α (s) = L 1 e.g., U-Mn 8. Development of Microstructure The microstructure developed depends on the overall composition and the cooling rate 9. Chemical Activity A measure of the escaping tendency Dr Ali Salami Golezani Page 5

6 Phase diagram for the Pb-Sn system Chemical Composition of Phases at any temperature Consider points A and B on the Pb-Sn phase diagram in Figure (above). At a constitution point in a singlephase region, the phase composition is simply the composition of the alloy itself. Constitution point A (temperature 250ºC, alloy composition Pb-30wt% Sn) lies in the single-phase liquid field; the phase composition is also Pb-30wt% Sn. In two-phase regions, the phase compositions are given by the values on the phase boundaries at the ends of the tieline through the constitution point. Recall that these are the saturation limits of the single-phase fields on the other sides of the boundaries. Constitution point B (temperature 130ºC, alloy composition C = 40wt% Sn) lies in a two phase field with two solid phases identified from the ends of the tie-line: (Pb) and (Sn); the phase compositions are Pb-7wt% Sn and Pb- 98wt% Sn respectively Amount of Phases at any Temperature Consider the alloy with composition W Sn = 20 wt% Sn at 250ºC in Figure, a constitution point in the twophase field: liquid plus Pb-rich solid. To find the proportions of each phase, first construct a tie-line through Dr Ali Salami Golezani Page 6

7 the constitution point and read off the compositions of the phases: Pb-rich solid (Pb) with composition (Pb) W Sn = 12 wt% Sn; Liquid L with composition W Sn = 34 wt% Sn. The tie-line is of length l, while the lengths of the segments to either side of the constitution point are a and b respectively (all compositions in wt% Sn). For the example alloy of composition WSn = 20 wt% Sn: The weight fractions of liquid and solid in the alloy are: F L = a / l and F (Pb) = b / l. Hence: F L = 8/22 = 36% and F (Pb) = 14/22 = 64% Determination of Phase Diagrams 1. Cooling Curves 2. Differential Scanning Calorimetry 3. Thermomechanical Analysis 4. Differential Thermal Analysis 5. Metallography 6. Energy Dispersive X-ray Spectroscopy 7. Electron Microprobe Analyzer 8. X-ray Diffraction 9. Transmission Electron Microscopy Dr Ali Salami Golezani Page 7

8 Cooling Curves 5-5-Types of Thermal Equilibrium Diagram We will now consider the main types of thermal equilibrium diagram which are of use in studying metallic alloy systems. Generally a useful alloy will only be formed when the two metals are completely soluble in each other in the liquid state; but in some instances the two metals are only partially soluble as liquids. We will begin with a brief study of one such case Two metals, Mutually Soluble in all Proportions in the Liquid State, Remain Mutually Soluble in all Proportions in the Solid State liquidus and solidus are congruent Dr Ali Salami Golezani Page 8

9 Development of Microstructure in Equilibrium (very slow) Cooling Solidification in the solid+liquid phase occurs gradually upon cooling from the liquidus line. The composition of the solid and the liquid change gradually during cooling (as can be determined by the tie-line method.). Nuclei of the solid phase form and they grow to consume all the liquid at the solidus line. Solidification Development of Microstructure in Non-equilibrium Cooling 1. Compositional changes require diffusion in solid and liquid phases 2. Diffusion in the solid state is very slow. The new layers that solidify on top of the existing grains have the equilibrium composition at that temperature but once they are solid their composition does not change. Formation of layered (cored) grains and the invalidity of the tie-line method to determine the composition of the solid phase. 3. The tie-line method still works for the liquid phase, where diffusion is fast. Average Ni content of solid grains is higher. Application of the lever rule gives us a greater proportion of liquid phase as compared to the one for equilibrium cooling at the same T. Solidus line is shifted to the right (higher Ni contents), solidification is complete at lower T, the outer part of the grains are richer in the low-melting component (Cu). 4. Upon heating grain boundaries will melt first. This can lead to premature mechanical failure. Dr Ali Salami Golezani Page 9

10 Note: Diffusion Diffusion is the migration of atoms from a region of high concentration to a region of low concentration. Interdiffusion: in a solid with more than one type of element (an alloy), atoms tend to migrate from regions of large concentration. Self-diffusion: In an elemental solid, atoms also migrate. Diffusion Mechanisms are, Interstitial, Vacancy and Substitutional, Dr Ali Salami Golezani Page 10

11 Processing Using Diffusion FASTER for Open crystal structures 2. Lower melting temp. mat ls 3. Mat ls w/secondary bonding 4. Cations 5. Smaller Diffusing atoms 6. Lower density mat ls Diffusion SLOWER for... 1) Close packed structures 2) High melting temp. mat ls 3) Mat ls w/covalent bonding 4) Anions 5) Larger diffusing atoms 6) Higher density mat ls Two Metals Mutually Soluble in all Proportions in the Liquid State Becoming Completely Insoluble in the Solid State Consider the solidification of an alloy of composition x, ie containing about 80% cadmium and 20% bismuth. When the temperature falls to T, crystal nuclei of pure cadmium begin. (The temperature horizontal or tie-line, T, cuts the liquidus at the chosen composition, x, and the other phase boundary is the 100% cadmium ordinate.). Since pure cadmium is deposited, it follows that the liquid which remains becomes correspondingly richer in bismuth. Therefore the composition of the liquid moves to the left say, to x\ and, as indicated by the diagram, no further deposition of cadmium takes place until the temperature has fallen to Ti. When this happens more cadmium is deposited, and dendrites begin to develop from the nuclei which have already formed. The growth of the cadmium dendrites, on the one hand, and the consequent enrichment of the remaining liquid in bismuth, on the other, continues until the Dr Ali Salami Golezani Page 11

12 temperature has fallen to 1400C. The remaining liquid then contains 40% cadmium and 60% bismuth, ie the eutectic point E has been reached. At this point the two metals are in equilibrium in the liquid, but, due to the momentum of crystallisation, the composition swings a little too far past the point E, resulting in the deposition of a little too much cadmium. In order that equilibrium shall be maintained, a swing back in composition across the eutectic point takes place by the deposition of a layer of bismuth. In this way the composition of the liquid oscillates about E by depositing alternate layers of cadmium and bismuth, whilst the temperature remains at 1400C until the remaining liquid has solidified. Thus the final structure will consist of primary crystals of cadmium which formed between the temperature T and 1400C, and a eutectic consisting of alternate layers of cadmium and bismuth which formed at 1400C. Hypo-Eutectic Microstructure -Eutectic Microstructure Hyer-Eutectic Microstructure Dr Ali Salami Golezani Page 12

13 5-5-3-Two Metals Mutually Soluble in all Proportions in the Liquid State but only Partially Soluble in the Solid State Three single phase regions (α - solid solution of Ag in Cu matrix, β = solid solution of Cu in Ag matrix, L - liquid) & Three two-phase regions (α + L, β +L, α +β) Dr Ali Salami Golezani Page 13

14 Development of Microstructure Several different types of microstructure can be formed in slow cooling an different compositions. Let s consider cooling of liquid lead tin system as an example. In the case of lead-rich alloy (0-2 wt. % of tin) solidification proceeds in the same manner as for isomorphous alloys (e.g. Cu-Ni) that we discussed earlier. L α+l α At compositions between the room temperature solubility limit and the maximum solid solubility at the eutectic temperature, β phase nucleates as the α solid solubility is exceeded upon crossing the solvus line. L α+l α α + β Dr Ali Salami Golezani Page 14

15 Note: Age Hardening Treatment Hypothetical phase diagram for a precipitation-hardenable alooy of composition C o Age Hardenind haet treatment cycle, showing both solution and aging treatment Systems containing one or more Compound Phase Dr Ali Salami Golezani Page 15

16 5-5-5-System in which a Peritectic Transformation is Involved Sometimes in an alloy system two phases which are already present interact at a fixed temperature to produce an entirely new phase. This is known as a peritectic transformation. Dr Ali Salami Golezani Page 16

17 5-5-6-System in which a Monotectic Transformation is Involved Solid State Reaction Eutectoid Reactions The eutectoid (eutectic-like in Greek) reaction is similar to the eutectic reaction but occurs from one solid phase to two new solid Eutectoid structures are similar to eutectic structures but are much finer in scale (diffusion is much slower in the solid state). Upon cooling, a solid phase transforms into two other solid phases (δ - γ + ε in the example below) Dr Ali Salami Golezani Page 17

18 Peritectoid is a three-phase reaction similar to peritectic but occurs from two solid phases to one new solid phase α + β = γ. Order-Disorder Transformation Allotropy Summary of reactions Dr Ali Salami Golezani Page 18

19 Dr Ali Salami Golezani Page 19

20 Dr Ali Salami Golezani Page 20

Introduction to Materials Science, Chapter 9, Phase Diagrams. Phase Diagrams. University of Tennessee, Dept. of Materials Science and Engineering 1

Introduction to Materials Science, Chapter 9, Phase Diagrams. Phase Diagrams. University of Tennessee, Dept. of Materials Science and Engineering 1 Phase Diagrams University of Tennessee, Dept. of Materials Science and Engineering 1 Chapter Outline: Phase Diagrams Microstructure and Phase Transformations in Multicomponent Systems Definitions and basic

More information

Phase. Gibbs Phase rule

Phase. Gibbs Phase rule Phase diagrams Phase A phase can be defined as a physically distinct and chemically homogeneous portion of a system that has a particular chemical composition and structure. Water in liquid or vapor state

More information

Phase Equilibria & Phase Diagrams

Phase Equilibria & Phase Diagrams Phase Equilibria & Phase Diagrams Week7 Material Sciences and Engineering MatE271 1 Motivation Phase diagram (Ch 9) Temperature Time Kinematics (Ch 10) New structure, concentration (mixing level) (at what

More information

BINARY SYSTEMS. Definition of Composition: Atomic (molar) fraction. Atomic percent. Mass fraction. Mass percent (weight percent)

BINARY SYSTEMS. Definition of Composition: Atomic (molar) fraction. Atomic percent. Mass fraction. Mass percent (weight percent) BINARY SYSTEMS Definition of Composition: Atomic (molar) fraction Atomic percent Mass fraction Mass percent (weight percent) na =, x i n = A i i i Weight percent mainly in industry! x at % A = x 100 A

More information

Chapter 8. Phase Diagrams

Chapter 8. Phase Diagrams Phase Diagrams A phase in a material is a region that differ in its microstructure and or composition from another region Al Al 2 CuMg H 2 O(solid, ice) in H 2 O (liquid) 2 phases homogeneous in crystal

More information

Lecture 19: Eutectoid Transformation in Steels: a typical case of Cellular

Lecture 19: Eutectoid Transformation in Steels: a typical case of Cellular Lecture 19: Eutectoid Transformation in Steels: a typical case of Cellular Precipitation Today s topics Understanding of Cellular transformation (or precipitation): when applied to phase transformation

More information

Binary phase diagrams

Binary phase diagrams inary phase diagrams inary phase diagrams and ibbs free energy curves inary solutions with unlimited solubility Relative proportion of phases (tie lines and the lever principle) Development of microstructure

More information

Alloys & Their Phase Diagrams

Alloys & Their Phase Diagrams Alloys & Their Phase Diagrams Objectives of the class Gibbs phase rule Introduction to phase diagram Practice phase diagram Lever rule Important Observation: One question in the midterm Consider the Earth

More information

μ α =μ β = μ γ = =μ ω μ α =μ β =μ γ = =μ ω Thus for c components, the number of additional constraints is c(p 1) ( ) ( )

μ α =μ β = μ γ = =μ ω μ α =μ β =μ γ = =μ ω Thus for c components, the number of additional constraints is c(p 1) ( ) ( ) Phase Diagrams 1 Gibbs Phase Rule The Gibbs phase rule describes the degrees of freedom available to describe a particular system with various phases and substances. To derive the phase rule, let us begin

More information

CHAPTER 8. Phase Diagrams 8-1

CHAPTER 8. Phase Diagrams 8-1 CHAPTER 8 Phase Diagrams 8-1 Introducción Fase: Una region en un material que difiere en estructura y función de otra región. Diagramas de fase : Representan las fases presentes en el metal a diferentes

More information

9.11 Upon heating a lead-tin alloy of composition 30 wt% Sn-70 wt% Pb from 150 C and utilizing Figure

9.11 Upon heating a lead-tin alloy of composition 30 wt% Sn-70 wt% Pb from 150 C and utilizing Figure 9-13 9.8: 9.11 Upon heating a lead-tin alloy of composition 30 wt% Sn-70 wt% Pb from 150 C and utilizing Figure (a) The first liquid forms at the temperature at which a vertical line at this composition

More information

CHAPTER 9 Part 1. = 5 wt% Sn-95 wt% Pb C β. = 98 wt% Sn-2 wt% Pb. = 77 wt% Ag-23 wt% Cu. = 51 wt% Zn-49 wt% Cu C γ. = 58 wt% Zn-42 wt% Cu

CHAPTER 9 Part 1. = 5 wt% Sn-95 wt% Pb C β. = 98 wt% Sn-2 wt% Pb. = 77 wt% Ag-23 wt% Cu. = 51 wt% Zn-49 wt% Cu C γ. = 58 wt% Zn-42 wt% Cu CHAPTER 9 Part 1 9.5 This problem asks that we cite the phase or phases present for several alloys at specified temperatures. (a) For an alloy composed of 15 wt% Sn-85 wt% Pb and at 100 C, from Figure

More information

Iron-Carbon Phase Diagram (a review) see Callister Chapter 9

Iron-Carbon Phase Diagram (a review) see Callister Chapter 9 Iron-Carbon Phase Diagram (a review) see Callister Chapter 9 University of Tennessee, Dept. of Materials Science and Engineering 1 The Iron Iron Carbide (Fe Fe 3 C) Phase Diagram In their simplest form,

More information

Phase Transformations in Metals and Alloys

Phase Transformations in Metals and Alloys Phase Transformations in Metals and Alloys THIRD EDITION DAVID A. PORTER, KENNETH E. EASTERLING, and MOHAMED Y. SHERIF ( г йс) CRC Press ^ ^ ) Taylor & Francis Group Boca Raton London New York CRC Press

More information

LN 10. 3.091 Introduction to Solid State Chemistry. Lecture Notes No. 10 PHASE EQUILIBRIA AND PHASE DIAGRAMS

LN 10. 3.091 Introduction to Solid State Chemistry. Lecture Notes No. 10 PHASE EQUILIBRIA AND PHASE DIAGRAMS 3.091 Introduction to Solid State Chemistry Lecture Notes No. 10 PHASE EQUILIBRIA AND PHASE DIAGRAMS * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Sources

More information

MSE 528 - PRECIPITATION HARDENING IN 7075 ALUMINUM ALLOY

MSE 528 - PRECIPITATION HARDENING IN 7075 ALUMINUM ALLOY MSE 528 - PRECIPITATION HARDENING IN 7075 ALUMINUM ALLOY Objective To study the time and temperature variations in the hardness and electrical conductivity of Al-Zn-Mg-Cu high strength alloy on isothermal

More information

Ch. 4: Imperfections in Solids Part 1. Dr. Feras Fraige

Ch. 4: Imperfections in Solids Part 1. Dr. Feras Fraige Ch. 4: Imperfections in Solids Part 1 Dr. Feras Fraige Outline Defects in Solids 0D, Point defects vacancies Interstitials impurities, weight and atomic composition 1D, Dislocations edge screw 2D, Grain

More information

Defects Introduction. Bonding + Structure + Defects. Properties

Defects Introduction. Bonding + Structure + Defects. Properties Defects Introduction Bonding + Structure + Defects Properties The processing determines the defects Composition Bonding type Structure of Crystalline Processing factors Defects Microstructure Types of

More information

Metals and Non-metals. Comparison of physical properties of metals and non metals

Metals and Non-metals. Comparison of physical properties of metals and non metals Metals and Non-metals Comparison of physical properties of metals and non metals PHYSICAL PROPERTY METALS NON-METALS Physical State Metallic lustre (having a shining surface) Mostly solids (Liquid -mercury)

More information

DIFFUSION IN SOLIDS. Materials often heat treated to improve properties. Atomic diffusion occurs during heat treatment

DIFFUSION IN SOLIDS. Materials often heat treated to improve properties. Atomic diffusion occurs during heat treatment DIFFUSION IN SOLIDS WHY STUDY DIFFUSION? Materials often heat treated to improve properties Atomic diffusion occurs during heat treatment Depending on situation higher or lower diffusion rates desired

More information

REACTIONS IN THE SN CORNER OF THE CU-SN-ZN ALLOY SYSTEM

REACTIONS IN THE SN CORNER OF THE CU-SN-ZN ALLOY SYSTEM REACTIONS IN THE SN CORNER OF THE CU-SN-ZN ALLOY SYSTEM D.D. Perovic, L Snugovsky and J.W. Rutter Department of Materials Science and Engineering University of Toronto Toronto, ON, Canada doug.perovic@utoronto.ca

More information

FEATURES AND BENEFITS OF DIFFERENT PLATINUM ALLOYS. Kris Vaithinathan and Richard Lanam Engelhard Corporation

FEATURES AND BENEFITS OF DIFFERENT PLATINUM ALLOYS. Kris Vaithinathan and Richard Lanam Engelhard Corporation FEATURES AND BENEFITS OF DIFFERENT PLATINUM ALLOYS Kris Vaithinathan and Richard Lanam Engelhard Corporation Introduction There has been a significant increase in the world wide use of platinum for jewelry

More information

Untitled Document. 1. Which of the following best describes an atom? 4. Which statement best describes the density of an atom s nucleus?

Untitled Document. 1. Which of the following best describes an atom? 4. Which statement best describes the density of an atom s nucleus? Name: Date: 1. Which of the following best describes an atom? A. protons and electrons grouped together in a random pattern B. protons and electrons grouped together in an alternating pattern C. a core

More information

Phase Diagrams & Thermodynamics

Phase Diagrams & Thermodynamics Phase Diagrams & Thermodynamics A phase diagram is a graphical representation of the equilibrium state of a system using the intensive variables T and i while p is kept constant. The equilibrium may be

More information

Ionic and Metallic Bonding

Ionic and Metallic Bonding Ionic and Metallic Bonding BNDING AND INTERACTINS 71 Ions For students using the Foundation edition, assign problems 1, 3 5, 7 12, 14, 15, 18 20 Essential Understanding Ions form when atoms gain or lose

More information

B) atomic number C) both the solid and the liquid phase D) Au C) Sn, Si, C A) metal C) O, S, Se C) In D) tin D) methane D) bismuth B) Group 2 metal

B) atomic number C) both the solid and the liquid phase D) Au C) Sn, Si, C A) metal C) O, S, Se C) In D) tin D) methane D) bismuth B) Group 2 metal 1. The elements on the Periodic Table are arranged in order of increasing A) atomic mass B) atomic number C) molar mass D) oxidation number 2. Which list of elements consists of a metal, a metalloid, and

More information

Chapter Outline: Phase Transformations in Metals

Chapter Outline: Phase Transformations in Metals Chapter Outline: Phase Transformations in Metals Heat Treatment (time and temperature) Microstructure Mechanical Properties Kinetics of phase transformations Multiphase Transformations Phase transformations

More information

Lecture: 33. Solidification of Weld Metal

Lecture: 33. Solidification of Weld Metal Lecture: 33 Solidification of Weld Metal This chapter presents common solidification mechanisms observed in weld metal and different modes of solidification. Influence of welding speed and heat input on

More information

Chapter 5: Diffusion. 5.1 Steady-State Diffusion

Chapter 5: Diffusion. 5.1 Steady-State Diffusion : Diffusion Diffusion: the movement of particles in a solid from an area of high concentration to an area of low concentration, resulting in the uniform distribution of the substance Diffusion is process

More information

Interface Reaction and Mechanical Properties of Lead-free Sn Zn Alloy/Cu Joints

Interface Reaction and Mechanical Properties of Lead-free Sn Zn Alloy/Cu Joints Materials Transactions, Vol. 43, No. 8 (2002) pp. 1797 to 1801 Special Issue on Lead-Free Electronics Packaging c 2002 The Japan Institute of Metals Interface Reaction and Mechanical Properties of Lead-free

More information

Heterogeneous Homogenous. Mixtures; Solutions. Phases of matter: Solid. Phases of Matter: Liquid. Phases of Matter: Gas. Solid, Liquid, Gas

Heterogeneous Homogenous. Mixtures; Solutions. Phases of matter: Solid. Phases of Matter: Liquid. Phases of Matter: Gas. Solid, Liquid, Gas Phases of matter: Solid Heterogeneous Homogenous Mixtures Solutions Phases of Matter: Liquid Atoms and molecules are more spaced out and now can move. The material can be slightly compressed into a smaller

More information

APPENDIX B: EXERCISES

APPENDIX B: EXERCISES BUILDING CHEMISTRY LABORATORY SESSIONS APPENDIX B: EXERCISES Molecular mass, the mole, and mass percent Relative atomic and molecular mass Relative atomic mass (A r ) is a constant that expresses the ratio

More information

CHAPTER 3: MATTER. Active Learning Questions: 1-6, 9, 13-14; End-of-Chapter Questions: 1-18, 20, 24-32, 38-42, 44, 49-52, 55-56, 61-64

CHAPTER 3: MATTER. Active Learning Questions: 1-6, 9, 13-14; End-of-Chapter Questions: 1-18, 20, 24-32, 38-42, 44, 49-52, 55-56, 61-64 CHAPTER 3: MATTER Active Learning Questions: 1-6, 9, 13-14; End-of-Chapter Questions: 1-18, 20, 24-32, 38-42, 44, 49-52, 55-56, 61-64 3.1 MATTER Matter: Anything that has mass and occupies volume We study

More information

Warm-Up 9/9. 1. Define the term matter. 2. Name something in this room that is not matter.

Warm-Up 9/9. 1. Define the term matter. 2. Name something in this room that is not matter. Warm-Up 9/9 1. Define the term matter. 2. Name something in this room that is not matter. Warm-Up 9/16 1. List the three most important rules of lab safety. 2. Would you classify jello as a solid or a

More information

100% ionic compounds do not exist but predominantly ionic compounds are formed when metals combine with non-metals.

100% ionic compounds do not exist but predominantly ionic compounds are formed when metals combine with non-metals. 2.21 Ionic Bonding 100% ionic compounds do not exist but predominantly ionic compounds are formed when metals combine with non-metals. Forming ions Metal atoms lose electrons to form +ve ions. Non-metal

More information

Thermodynamic database of the phase diagrams in copper base alloy systems

Thermodynamic database of the phase diagrams in copper base alloy systems Journal of Physics and Chemistry of Solids 66 (2005) 256 260 www.elsevier.com/locate/jpcs Thermodynamic database of the phase diagrams in copper base alloy systems C.P. Wang a, X.J. Liu b, M. Jiang b,

More information

THREE MAIN SOLIDIFICATION REACTIONS OF VANADIUM MODIFIED T1 TUNGSTEN HIGH SPEED TOOL STEEL. Hossam Halfa

THREE MAIN SOLIDIFICATION REACTIONS OF VANADIUM MODIFIED T1 TUNGSTEN HIGH SPEED TOOL STEEL. Hossam Halfa THREE MAIN SOLIDIFICATION REACTIONS OF VANADIUM MODIFIED T1 TUNGSTEN HIGH SPEED TOOL STEEL Hossam Halfa Steel Technology Department, Central Metallurgical R&D Institute (CMRDI), Helwan, Egypt, hossamhalfa@cmrdi.sci.eg;

More information

Introduction To Materials Science FOR ENGINEERS, Ch. 5. Diffusion. MSE 201 Callister Chapter 5

Introduction To Materials Science FOR ENGINEERS, Ch. 5. Diffusion. MSE 201 Callister Chapter 5 Diffusion MSE 21 Callister Chapter 5 1 Goals: Diffusion - how do atoms move through solids? Fundamental concepts and language Diffusion mechanisms Vacancy diffusion Interstitial diffusion Impurities Diffusion

More information

The atomic packing factor is defined as the ratio of sphere volume to the total unit cell volume, or APF = V S V C. = 2(sphere volume) = 2 = V C = 4R

The atomic packing factor is defined as the ratio of sphere volume to the total unit cell volume, or APF = V S V C. = 2(sphere volume) = 2 = V C = 4R 3.5 Show that the atomic packing factor for BCC is 0.68. The atomic packing factor is defined as the ratio of sphere volume to the total unit cell volume, or APF = V S V C Since there are two spheres associated

More information

KINETIC MOLECULAR THEORY OF MATTER

KINETIC MOLECULAR THEORY OF MATTER KINETIC MOLECULAR THEORY OF MATTER The kinetic-molecular theory is based on the idea that particles of matter are always in motion. The theory can be used to explain the properties of solids, liquids,

More information

The mechanical properties of metal affected by heat treatment are:

The mechanical properties of metal affected by heat treatment are: Training Objective After watching this video and reviewing the printed material, the student/trainee will learn the basic concepts of the heat treating processes as they pertain to carbon and alloy steels.

More information

In order to solve this problem it is first necessary to use Equation 5.5: x 2 Dt. = 1 erf. = 1.30, and x = 2 mm = 2 10-3 m. Thus,

In order to solve this problem it is first necessary to use Equation 5.5: x 2 Dt. = 1 erf. = 1.30, and x = 2 mm = 2 10-3 m. Thus, 5.3 (a) Compare interstitial and vacancy atomic mechanisms for diffusion. (b) Cite two reasons why interstitial diffusion is normally more rapid than vacancy diffusion. Solution (a) With vacancy diffusion,

More information

Atoms and Elements. Atoms: Learning Goals. Chapter 3. Atoms and Elements; Isotopes and Ions; Minerals and Rocks. Clicker 1. Chemistry Background?

Atoms and Elements. Atoms: Learning Goals. Chapter 3. Atoms and Elements; Isotopes and Ions; Minerals and Rocks. Clicker 1. Chemistry Background? Chapter 3 Atoms Atoms and Elements; Isotopes and Ions; Minerals and Rocks A Review of Chemistry: What geochemistry tells us Clicker 1 Chemistry Background? A. No HS or College Chemistry B. High School

More information

Review - After School Matter Name: Review - After School Matter Tuesday, April 29, 2008

Review - After School Matter Name: Review - After School Matter Tuesday, April 29, 2008 Name: Review - After School Matter Tuesday, April 29, 2008 1. Figure 1 The graph represents the relationship between temperature and time as heat was added uniformly to a substance starting at a solid

More information

Corrosion-induced cracking of model train zincaluminium

Corrosion-induced cracking of model train zincaluminium Nationaal Lucht- en Ruimtevaartlaboratorium National Aerospace Laboratory NLR Corrosion-induced cracking of model train zincaluminium die castings R.J.H. Wanhill and T. Hattenberg This report may be cited

More information

Problems in Welding of High Strength Aluminium Alloys

Problems in Welding of High Strength Aluminium Alloys Singapore Welding Society Newsletter, September 1999 Problems in Welding of High Strength Aluminium Alloys Wei Zhou Nanyang Technological University, Singapore E-mail: WZhou@Cantab.Net Pure aluminium has

More information

PRODUCT PROFILE. ELECTROLOY in partnership with FCT Asia Pte Limited. in manufacturing. Nihon Superior Lead Free Solder Bar.

PRODUCT PROFILE. ELECTROLOY in partnership with FCT Asia Pte Limited. in manufacturing. Nihon Superior Lead Free Solder Bar. PRODUCT PROFILE ELECTROLOY in partnership with FCT Asia Pte Limited in manufacturing Nihon Superior Lead Free Solder Bar SN100C Product Name Product Code LEAD FREE BAR LEAD FREE BAR ( TOP UP ALLOY ) SN100C

More information

3. What would you predict for the intensity and binding energy for the 3p orbital for that of sulfur?

3. What would you predict for the intensity and binding energy for the 3p orbital for that of sulfur? PSI AP Chemistry Periodic Trends MC Review Name Periodic Law and the Quantum Model Use the PES spectrum of Phosphorus below to answer questions 1-3. 1. Which peak corresponds to the 1s orbital? (A) 1.06

More information

Chapter 14 Solutions

Chapter 14 Solutions Chapter 14 Solutions 1 14.1 General properties of solutions solution a system in which one or more substances are homogeneously mixed or dissolved in another substance two components in a solution: solute

More information

Chemistry B11 Chapter 6 Solutions and Colloids

Chemistry B11 Chapter 6 Solutions and Colloids Chemistry B11 Chapter 6 Solutions and Colloids Solutions: solutions have some properties: 1. The distribution of particles in a solution is uniform. Every part of the solution has exactly the same composition

More information

Soldering Definition and Differences

Soldering Definition and Differences Soldering Understanding the Basics Copyright 2014 ASM International M. Schwartz, editor All rights reserved www.asminternational.org Chapter 1 Soldering Definition and Differences SOLDER IS A FUSIBLE METAL

More information

RAPIDLY SOLIDIFIED COPPER ALLOYS RIBBONS

RAPIDLY SOLIDIFIED COPPER ALLOYS RIBBONS Association of Metallurgical Engineers of Serbia AMES Scientific paper UDC:669.35-153.881-412.2=20 RAPIDLY SOLIDIFIED COPPER ALLOYS RIBBONS M. ŠULER 1, L. KOSEC 1, A. C. KNEISSL 2, M. BIZJAK 1, K. RAIĆ

More information

Solidification, Crystallization & Glass Transition

Solidification, Crystallization & Glass Transition Solidification, Crystallization & Glass Transition Cooling the Melt solidification Crystallization versus Formation of Glass Parameters related to the formaton of glass Effect of cooling rate Glass transition

More information

UNIT (2) ATOMS AND ELEMENTS

UNIT (2) ATOMS AND ELEMENTS UNIT (2) ATOMS AND ELEMENTS 2.1 Elements An element is a fundamental substance that cannot be broken down by chemical means into simpler substances. Each element is represented by an abbreviation called

More information

Chapter Outline Dislocations and Strengthening Mechanisms

Chapter Outline Dislocations and Strengthening Mechanisms Chapter Outline Dislocations and Strengthening Mechanisms What is happening in material during plastic deformation? Dislocations and Plastic Deformation Motion of dislocations in response to stress Slip

More information

Chapter 6 Assessment. Name: Class: Date: ID: A. Multiple Choice Identify the choice that best completes the statement or answers the question.

Chapter 6 Assessment. Name: Class: Date: ID: A. Multiple Choice Identify the choice that best completes the statement or answers the question. Name: Class: Date: ID: A Chapter 6 Assessment Multiple Choice Identify the choice that best completes the statement or answers the question. 1. When an atom loses an electron, it forms a(n) a. anion. c.

More information

The Periodic Table: Periodic trends

The Periodic Table: Periodic trends Unit 1 The Periodic Table: Periodic trends There are over one hundred different chemical elements. Some of these elements are familiar to you such as hydrogen, oxygen, nitrogen and carbon. Each one has

More information

The study about as cast microstructure and solidification

The study about as cast microstructure and solidification The study about as cast microstructure and solidification process of Al-Mg-Si alloys Introduction High-strength and high formability aluminum alloys are the highly demanded alloy in automobile industry,

More information

Name Class Date. In the space provided, write the letter of the term or phrase that best completes each statement or best answers each question.

Name Class Date. In the space provided, write the letter of the term or phrase that best completes each statement or best answers each question. Assessment Chapter Test A Chapter: States of Matter In the space provided, write the letter of the term or phrase that best completes each statement or best answers each question. 1. The kinetic-molecular

More information

BOND TYPES: THE CLASSIFICATION OF SUBSTANCES

BOND TYPES: THE CLASSIFICATION OF SUBSTANCES BOND TYPES: THE CLASSIFICATION OF SUBSTANCES Every (pure) substance has a unique set of intrinsic properties which distinguishes it from all other substances. What inferences, if any can be made from a

More information

Name Date Class CHAPTER 1 REVIEW. Answer the following questions in the space provided.

Name Date Class CHAPTER 1 REVIEW. Answer the following questions in the space provided. CHAPTER 1 REVIEW Matter and Change SECTION 1 SHORT ANSWER Answer the following questions in the space provided. 1. a Technological development of a chemical product often (a) lags behind basic research

More information

Chapter Outline. Diffusion - how do atoms move through solids?

Chapter Outline. Diffusion - how do atoms move through solids? Chapter Outline iffusion - how do atoms move through solids? iffusion mechanisms Vacancy diffusion Interstitial diffusion Impurities The mathematics of diffusion Steady-state diffusion (Fick s first law)

More information

EXAMPLE EXERCISE 4.1 Change of Physical State

EXAMPLE EXERCISE 4.1 Change of Physical State EXAMPLE EXERCISE 4.1 Change of Physical State State the term that applies to each of the following changes of physical state: (a) Snow changes from a solid to a liquid. (b) Gasoline changes from a liquid

More information

Objectives/Introduction Extraction of zinc Physical properties of zinc Zinc casting alloys Wrought zinc alloys Engineering design with zinc alloys

Objectives/Introduction Extraction of zinc Physical properties of zinc Zinc casting alloys Wrought zinc alloys Engineering design with zinc alloys Lecture 7 Zinc and its alloys Subjects of interest Objectives/Introduction Extraction of zinc Physical properties of zinc Zinc casting alloys Wrought zinc alloys Engineering design with zinc alloys Objectives

More information

Chemistry 51 Chapter 8 TYPES OF SOLUTIONS. A solution is a homogeneous mixture of two substances: a solute and a solvent.

Chemistry 51 Chapter 8 TYPES OF SOLUTIONS. A solution is a homogeneous mixture of two substances: a solute and a solvent. TYPES OF SOLUTIONS A solution is a homogeneous mixture of two substances: a solute and a solvent. Solute: substance being dissolved; present in lesser amount. Solvent: substance doing the dissolving; present

More information

Heat Treatment of Steel

Heat Treatment of Steel Heat Treatment of Steel Steels can be heat treated to produce a great variety of microstructures and properties. Generally, heat treatment uses phase transformation during heating and cooling to change

More information

Chapter 13: Properties of Solutions

Chapter 13: Properties of Solutions Chapter 13: Properties of Solutions Problems: 9-10, 13-17, 21-42, 44, 49-60, 71-72, 73 (a,c), 77-79, 84(a-c), 91 solution: homogeneous mixture of a solute dissolved in a solvent solute: solvent: component(s)

More information

Question Bank Electrolysis

Question Bank Electrolysis Question Bank Electrolysis 1. (a) What do you understand by the terms (i) electrolytes (ii) non-electrolytes? (b) Arrange electrolytes and non-electrolytes from the following substances (i) sugar solution

More information

Using the PDF for material identification using elemental data. from XRF and SEM EDS.

Using the PDF for material identification using elemental data. from XRF and SEM EDS. XRF and SEM EDS Using the PDF for material identification using elemental data from XRF and SEM EDS. XRF and SEM EDS What? The Powder Diffraction File contains data on pure solid state compounds of well

More information

Experiment 5: Phase diagram for a three-component system (Dated: April 12, 2010)

Experiment 5: Phase diagram for a three-component system (Dated: April 12, 2010) Experiment 5: Phase diagram for a three-component system (Dated: April 12, 2010) I. INTRODUCTION It is sometimes necessary to know the mutual solubilities of liquids in a two-phase system. For example,

More information

CHEMISTRY STANDARDS BASED RUBRIC ATOMIC STRUCTURE AND BONDING

CHEMISTRY STANDARDS BASED RUBRIC ATOMIC STRUCTURE AND BONDING CHEMISTRY STANDARDS BASED RUBRIC ATOMIC STRUCTURE AND BONDING Essential Standard: STUDENTS WILL UNDERSTAND THAT THE PROPERTIES OF MATTER AND THEIR INTERACTIONS ARE A CONSEQUENCE OF THE STRUCTURE OF MATTER,

More information

Unit 2 Periodic Behavior and Ionic Bonding

Unit 2 Periodic Behavior and Ionic Bonding Unit 2 Periodic Behavior and Ionic Bonding 6.1 Organizing the Elements I. The Periodic Law A. The physical and chemical properties of the elements are periodic functions of their atomic numbers B. Elements

More information

Chapter Outline Dislocations and Strengthening Mechanisms

Chapter Outline Dislocations and Strengthening Mechanisms Chapter Outline Dislocations and Strengthening Mechanisms What is happening in material during plastic deformation? Dislocations and Plastic Deformation Motion of dislocations in response to stress Slip

More information

Chemistry. The student will be able to identify and apply basic safety procedures and identify basic equipment.

Chemistry. The student will be able to identify and apply basic safety procedures and identify basic equipment. Chemistry UNIT I: Introduction to Chemistry The student will be able to describe what chemistry is and its scope. a. Define chemistry. b. Explain that chemistry overlaps many other areas of science. The

More information

Chapter 13 - LIQUIDS AND SOLIDS

Chapter 13 - LIQUIDS AND SOLIDS Chapter 13 - LIQUIDS AND SOLIDS Problems to try at end of chapter: Answers in Appendix I: 1,3,5,7b,9b,15,17,23,25,29,31,33,45,49,51,53,61 13.1 Properties of Liquids 1. Liquids take the shape of their container,

More information

Chapter Test A. Elements, Compounds, and Mixtures MULTIPLE CHOICE. chemically combined? MIXs2 a. element b. compound c. mixture d.

Chapter Test A. Elements, Compounds, and Mixtures MULTIPLE CHOICE. chemically combined? MIXs2 a. element b. compound c. mixture d. Assessment Chapter Test A Elements, Compounds, and Mixtures MULTIPLE CHOICE Write the letter of the correct answer in the space provided. 1. What is a pure substance made of two or more elements that are

More information

Chemistry Ch 15 (Solutions) Study Guide Introduction

Chemistry Ch 15 (Solutions) Study Guide Introduction Chemistry Ch 15 (Solutions) Study Guide Introduction Name: Note: a word marked (?) is a vocabulary word you should know the meaning of. A homogeneous (?) mixture, or, is a mixture in which the individual

More information

Heat Treatment of Steels : Spheroidize annealing. Heat Treatment of Steels : Normalizing

Heat Treatment of Steels : Spheroidize annealing. Heat Treatment of Steels : Normalizing Heat Treatment of Steels :Recrystallization annealing The carbon and alloy steels were treated at a temperature of about 700 C, which is about 20 C below the eutectoid temperature. The holding time should

More information

Unit 3 Study Guide: Electron Configuration & The Periodic Table

Unit 3 Study Guide: Electron Configuration & The Periodic Table Name: Teacher s Name: Class: Block: Date: Unit 3 Study Guide: Electron Configuration & The Periodic Table 1. For each of the following elements, state whether the element is radioactive, synthetic or both.

More information

Study the following diagrams of the States of Matter. Label the names of the Changes of State between the different states.

Study the following diagrams of the States of Matter. Label the names of the Changes of State between the different states. Describe the strength of attractive forces between particles. Describe the amount of space between particles. Can the particles in this state be compressed? Do the particles in this state have a definite

More information

(1) e.g. H hydrogen that has lost 1 electron c. anion - negatively charged atoms that gain electrons 16-2. (1) e.g. HCO 3 bicarbonate anion

(1) e.g. H hydrogen that has lost 1 electron c. anion - negatively charged atoms that gain electrons 16-2. (1) e.g. HCO 3 bicarbonate anion GS106 Chemical Bonds and Chemistry of Water c:wou:gs106:sp2002:chem.wpd I. Introduction A. Hierarchy of chemical substances 1. atoms of elements - smallest particles of matter with unique physical and

More information

Phase diagram of water. Note: for H 2 O melting point decreases with increasing pressure, for CO 2 melting point increases with increasing pressure.

Phase diagram of water. Note: for H 2 O melting point decreases with increasing pressure, for CO 2 melting point increases with increasing pressure. Phase diagram of water Note: for H 2 O melting point decreases with increasing pressure, for CO 2 melting point increases with increasing pressure. WATER Covers ~ 70% of the earth s surface Life on earth

More information

Formation of solids from solutions and melts

Formation of solids from solutions and melts Formation of solids from solutions and melts Solids from a liquid phase. 1. The liquid has the same composition as the solid. Formed from the melt without any chemical transformation. Crystallization and

More information

Bonding in Elements and Compounds. Covalent

Bonding in Elements and Compounds. Covalent Bonding in Elements and Compounds Structure of solids, liquids and gases Types of bonding between atoms and molecules Ionic Covalent Metallic Many compounds between metals & nonmetals (salts), e.g. Na,

More information

Chapter 13 - Solutions

Chapter 13 - Solutions Chapter 13 - Solutions 13-1 Types of Mixtures I. Solutions A. Soluble 1. Capable of being dissolved B. Solution 1. A homogeneous mixture of two or more substances in a single phase C. Solvent 1. The dissolving

More information

48 Practice Problems for Ch. 17 - Chem 1C - Joseph

48 Practice Problems for Ch. 17 - Chem 1C - Joseph 48 Practice Problems for Ch. 17 - Chem 1C - Joseph 1. Which of the following concentration measures will change in value as the temperature of a solution changes? A) mass percent B) mole fraction C) molality

More information

ATOMS. Multiple Choice Questions

ATOMS. Multiple Choice Questions Chapter 3 ATOMS AND MOLECULES Multiple Choice Questions 1. Which of the following correctly represents 360 g of water? (i) 2 moles of H 2 0 (ii) 20 moles of water (iii) 6.022 10 23 molecules of water (iv)

More information

Periodic Table Questions

Periodic Table Questions Periodic Table Questions 1. The elements characterized as nonmetals are located in the periodic table at the (1) far left; (2) bottom; (3) center; (4) top right. 2. An element that is a liquid at STP is

More information

Thermodynamics and Equilibrium

Thermodynamics and Equilibrium Chapter 19 Thermodynamics and Equilibrium Concept Check 19.1 You have a sample of 1.0 mg of solid iodine at room temperature. Later, you notice that the iodine has sublimed (passed into the vapor state).

More information

Lecture 3: Models of Solutions

Lecture 3: Models of Solutions Materials Science & Metallurgy Master of Philosophy, Materials Modelling, Course MP4, Thermodynamics and Phase Diagrams, H. K. D. H. Bhadeshia Lecture 3: Models of Solutions List of Symbols Symbol G M

More information

Chapter Outline. 3 Elements and Compounds. Elements and Atoms. Elements. Elements. Elements 9/4/2013

Chapter Outline. 3 Elements and Compounds. Elements and Atoms. Elements. Elements. Elements 9/4/2013 3 Elements and Compounds Chapter Outline 3.1 Elements A. Distribution of Elements Foundations of College Chemistry, 14 th Ed. Morris Hein and Susan Arena Copyright This reclining Buddha in Thailand is

More information

Chapter 12 - Liquids and Solids

Chapter 12 - Liquids and Solids Chapter 12 - Liquids and Solids 12-1 Liquids I. Properties of Liquids and the Kinetic Molecular Theory A. Fluids 1. Substances that can flow and therefore take the shape of their container B. Relative

More information

ORGANIC LABORATORY TECHNIQUES 10 10.1. NEVER distill the distillation flask to dryness as there is a risk of explosion and fire.

ORGANIC LABORATORY TECHNIQUES 10 10.1. NEVER distill the distillation flask to dryness as there is a risk of explosion and fire. ORGANIC LABORATORY TECHNIQUES 10 10.1 DISTILLATION NEVER distill the distillation flask to dryness as there is a risk of explosion and fire. The most common methods of distillation are simple distillation

More information

Everest. Leaders in Vacuum Booster Technology

Everest. Leaders in Vacuum Booster Technology This article has been compiled to understand the process of Solvent Recovery process generally carried out at low temperatures and vacuum. In many chemical processes solute is to be concentrated to high

More information

2. Write the chemical formula(s) of the product(s) and balance the following spontaneous reactions.

2. Write the chemical formula(s) of the product(s) and balance the following spontaneous reactions. 1. Using the Activity Series on the Useful Information pages of the exam write the chemical formula(s) of the product(s) and balance the following reactions. Identify all products phases as either (g)as,

More information

Pure Substances, Mixtures, and Solutions

Pure Substances, Mixtures, and Solutions Pure Substances, Mixtures, and Solutions Mixtures, elements, compounds Scientists like to classify things. One way that scientists classify matter is by its composition. Ultimately, all matter can be classified

More information

5. Which temperature is equal to +20 K? 1) 253ºC 2) 293ºC 3) 253 C 4) 293 C

5. Which temperature is equal to +20 K? 1) 253ºC 2) 293ºC 3) 253 C 4) 293 C 1. The average kinetic energy of water molecules increases when 1) H 2 O(s) changes to H 2 O( ) at 0ºC 3) H 2 O( ) at 10ºC changes to H 2 O( ) at 20ºC 2) H 2 O( ) changes to H 2 O(s) at 0ºC 4) H 2 O( )

More information

AP Chemistry Semester One Study Guide

AP Chemistry Semester One Study Guide AP Chemistry Semester One Study Guide Unit One: General Chemistry Review Unit Two: Organic Nomenclature Unit Three: Reactions Unit Four: Thermochemistry Unit Five: Electronic Structure of the Atom Unit

More information

States of Matter CHAPTER 10 REVIEW SECTION 1. Name Date Class. Answer the following questions in the space provided.

States of Matter CHAPTER 10 REVIEW SECTION 1. Name Date Class. Answer the following questions in the space provided. CHAPTER 10 REVIEW States of Matter SECTION 1 SHORT ANSWER Answer the following questions in the space provided. 1. Identify whether the descriptions below describe an ideal gas or a real gas. ideal gas

More information

Which substance contains positive ions immersed in a sea of mobile electrons? A) O2(s) B) Cu(s) C) CuO(s) D) SiO2(s)

Which substance contains positive ions immersed in a sea of mobile electrons? A) O2(s) B) Cu(s) C) CuO(s) D) SiO2(s) BONDING MIDTERM REVIEW 7546-1 - Page 1 1) Which substance contains positive ions immersed in a sea of mobile electrons? A) O2(s) B) Cu(s) C) CuO(s) D) SiO2(s) 2) The bond between hydrogen and oxygen in

More information