Australian Standard. Sampling procedures for inspection by attributes
|
|
|
- Iris Morrison
- 7 years ago
- Views:
Transcription
1 AS ISO :1999 Reconfirmed 2016 AS Australian Standard Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
2 This Australian Standard was prepared by Committee QR-008, Quality Systems. It was approved on behalf of the Council of Standards Australia on 26 May 2003 and published on 28 July The following are represented on Committee QR-008: Australian Chamber of Commerce and Industry Australian Industry Group Australian Information Industry Association Australian Institute of Petroleum Australian Organisation for Quality Bureau of Steel Manufacturers of Australia Certification Bodies (Australia) Commonwealth Department of Transport and Regional Services Department of Agriculture, Fisheries and Forestry (Commonwealth) Department of Defence (Australia) Department of Industry Science and Resources (Commonwealth) Federal Chamber of Automotive Industries Institute of Materials Engineering Australasia Institution of Engineers Australia Main Roads Department, Queensland Master Builders Australia Quality Society of Australasia Royal Australian Chemical Institute Additional interests participating in the preparation of this Standard: Australian Quality Council CSIRO Mathematical and Information Services Macquarie University National Association of Testing Authorities Australia Queensland University of Technology Keeping Standards up-to-date Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about Standards can be found by visiting the Standards Australia web site at and looking up the relevant Standard in the on-line catalogue. Alternatively, the printed Catalogue provides information current at 1 January each year, and the monthly magazine, The Global Standard, has a full listing of revisions and amendments published each month. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via at mail@standards.com.au, or write to the Chief Executive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW This Standard was issued in draft form for comment as DR
3 STANDARDS AUSTRALIA AS (Reconfirmed) RECONFIRMATION OF AS Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection RECONFIRMATION NOTICE Technical Committee QR-008 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change. Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice. Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 27 June The following are represented on Technical Committee QR-008: Association of Accredited Certification Bodies Australian Industry Group Australian Institute of Petroleum Australian Organisation for Quality Australian Prudential Regulation Authority Consumers Federation of Australia Energy Networks Association Engineers Australia Griffith University Housing NSW ISACA Joint Accreditation System of Australia and New Zealand Master Builders Australia Materials Australia New Zealand Organisation for Quality Royal Australian Chemical Institute University of Canterbury New Zealand University of Technology, Sydney University of Wollongong
4 NOTES
5 AS Australian Standard Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection Originated as AS Previous edition AS Revised and redesignated as AS COPYRIGHT Standards Australia International All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. Published by Standards Australia International Ltd GPO Box 5420, Sydney, NSW 2001, Australia ISBN
6 ii PREFACE This Standard was prepared by the Standards Australia Committee QR-008, Quality Systems. This Standard is identical with, and has been reproduced from ISO :1999, Sampling procedures for inspection by attributes, Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection. The objective of this Standard is to specify an acceptance sampling system for inspection by attributes. It is indexed in terms of the acceptance quality limit (AQL). As this Standard is reproduced from an international Standard, the following applies: (a) Its number appears on the cover and title page while the international Standard number appears only on the cover. (b) A full point substitutes for a comma when referring to a decimal marker. (c) In the column Sample size corresponding to the row for sample size code letter H, replace the value 50 with the value 20. NOTE: This correction is identical with Technical Corrigendum 1 (2001) to ISO :1999. References to International Standards should be replaced by references to Australian or Australian/New Zealand Standards, as follows: Reference to International Standard Australian Standard ISO AS 2859 Sampling procedures for inspection by attributes 1199 Sampling procedures for inspection by attributes Part 3: Skip-lot sampling procedures Part 3: Skip-lot sampling procedures Only International Standard referenced documents identical to Australian Standards have been listed. The term informative has been used in this Standard to define the application of the annex to which it applies. An informative annex is only for information and guidance. The International Organization for Standardization s Committee TC 69 is currently in the process of updating the ISO 2859 series to bring the older documents into line with Parts 1 and 4. Where any inconsistency arises between the sections of this series of Standards, the more recently published document will apply.
7 iii CONTENTS 1 Scope Normative references Terms, definitions and symbols Expression of nonconformity Acceptance quality limit (AQL) Submission of product for sampling Acceptance and non-acceptance Drawing of samples Normal, tightened and reduced inspection Sampling plans Determination of acceptability Further information Fractional acceptance number plans for single sampling (optional)...16 Tables 1 Sample size code letters A Single sampling plans for normal inspection (Master table) B Single sampling plans for tightened inspection (Master table) C Single sampling plans for reduced inspection (Master table) A Double sampling plans for normal inspection (Master table) B Double sampling plans for tightened inspection (Master table) C Double sampling plans for reduced inspection (Master table) A Multiple sampling plans for normal inspection (Master table) B Multiple sampling plans for tightened inspection (Master table)...29
8 iv 4-C Multiple sampling plans for reduced inspection (Master table) A Producer's risk for normal inspection B Producer's risk for tightened inspection C Producer's risk for reduced inspection A Consumer's risk quality for normal inspection B Consumer's risk quality for tightened inspection C Consumer's risk quality for reduced inspection A Consumer's risk quality for normal inspection B Consumer's risk quality for tightened inspection C Consumer's risk quality for reduced inspection A Average outgoing quality limits for normal inspection (Single sampling plans) B Average outgoing quality limits for tightened inspection (Single sampling plans) Average sample size curves for single, double and multiple sampling (normal, tightened and reduced inspection) A Tables for sample size code letter A (Individual plans) B Tables for sample size code letter B (Individual plans) C Tables for sample size code letter C (Individual plans) D Tables for sample size code letter D (Individual plans) E Tables for sample size code letter E (Individual plans) F Tables for sample size code letter F (Individual plans) G Tables for sample size code letter G (Individual plans) H Tables for sample size code letter H (Individual plans) J Tables for sample size code letter J (Individual plans) K Tables for sample size code letter K (Individual plans) L Tables for sample size code letter L (Individual plans) M Tables for sample size code letter M (Individual plans) N Tables for sample size code letter N (Individual plans) P Tables for sample size code letter P (Individual plans) Q Tables for sample size code letter Q (Individual plans) R Tables for sample size code letter R (Individual plans) S Tables for sample size code letter S (Individual plans)... 80
9 v 11-A Single sampling plans for normal inspection (Auxiliary master table) B Single sampling plans for tightened inspection (Auxiliary master table) C Single sampling plans for reduced inspection (Auxiliary master table) Scheme OC curves (Normalized)...84 Annex A (informative) Example for non-constant sampling plan...85 Bibliography...87
10 This is a free preview. Purchase the entire publication at the link below: Looking for additional Standards? Visit SAI Global Infostore Subscribe to our Free Newsletters Do you need to Manage Standards Collections Online? Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation Do you want to know when a Standard has changed? Create safe work processes for the workplace with our Safe Work Method Statements Learn about other SAI Global Services: LOGICOM Military Parts and Supplier Database Metals Infobase Database of Metal Grades, Standards and Manufacturers Materials Infobase Database of Materials, Standards and Suppliers Database of European Law, CELEX and Court Decisions Need to speak with a Customer Service Representative - Contact Us
Australian Standard. Quality management systems Guidelines for configuration management AS ISO 10007 2003 ISO 10007:2003 AS ISO 10007
AS ISO 10007 2003 ISO 10007:2003 AS ISO 10007 Australian Standard Quality management systems Guidelines for configuration management This Australian Standard was prepared by Committee QR-008, Quality Systems.
Australian Standard. Guidelines for quality management system documentation AS ISO 10013 2003 ISO/TR 10013:2001 AS ISO 10013
AS ISO 10013 2003 ISO/TR 10013:2001 AS ISO 10013 Australian Standard Guidelines for quality management system documentation This Australian Standard was prepared by Committee QR-008, Quality Systems. It
AS/NZS ISO 9001:2008 Quality management systems Requirements (Incorporating Amendment No. 1)
AS/NZS ISO 9001:2008 Quality management systems Requirements (Incorporating Amendment No. 1) AS AS/NZS AS/NZS ISO 9001:2008 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee
Australian Standard. Information technology Service management. Part 2: Guidance on the application of service management systems
ISO/IEC 20000-2:2012 AS ISO/IEC 20000.2 2013 Australian Standard Information technology Service Part 2: Guidance on the application of service systems This Australian Standard was prepared by Committee
This is a free 9 page sample. Access the full version online. AS/NZS ISO 31000:2009 Risk management Principles and guidelines
AS/NZS ISO 31000:2009 Risk management Principles and guidelines AS/NZS ISO 31000:2009 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee OB-007, Risk Management. It was
Australian Standard. Guidance on statistical techniques for ISO 9001:2000 (ISO/TR 10017, Ed. 2.0 (2003) MOD) AS ISO 10017 2006 AS ISO 10017 2006
AS ISO 10017 2006 AS ISO 10017 2006 Australian Standard Guidance on statistical techniques for ISO 9001:2000 (ISO/TR 10017, Ed. 2.0 (2003) MOD) This Australian Standard was prepared by Committee QR-008,
Australian/New Zealand Standard
AS/NZS 3200.1.8:2005 (IEC 60601-1-8:2003) AS/NZS 3200.1.8:2005 Australian/New Zealand Standard Medical electrical equipment Part 1.8: General requirements for safety Collateral Standard: General requirements,
Australian/New Zealand Standard
AS/NZS ISO/IEC 25000:2007 ISO/IEC 25000:2005 AS/NZS ISO/IEC 25000:2007 Australian/New Zealand Standard Software engineering Software product Quality Requirements and Evaluation (SQuaRE) Guide to SQuaRE
Australian/New Zealand Standard
AS/NZS ISO/IEC 16326:2006 ISO/IEC TR 16326:1999 AS/NZS ISO/IEC 16326:2006 Australian/New Zealand Standard Software engineering Guide for the application of ISO/IEC 12207 to project management AS/NZS ISO/IEC
Australian/New Zealand Standard
AS/NZS ISO 3834.5:2008 ISO 3834-5:2005 AS/NZS ISO 3834.5:2008 Australian/New Zealand Standard Quality requirements for fusion welding of metallic materials Part 5: Documents with which it is necessary
Australian Standard. Standard metamodel for software development methodologies AS 4651 2004 AS 4651 2004
AS 4651 2004 AS 4651 2004 Australian Standard Standard metamodel for software development methodologies This Australian Standard was prepared by Committee IT-015, Software and Systems Engineering. It was
This is a free 15 page sample. Access the full version online.
AS/NZS ISO/IEC 17799:2001 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee IT-012, Information Systems, Security and Identification Technology. It was approved on behalf
Australian/New Zealand Standard
AS/NZS 3500.4:2003 (Incorporating Amendment Nos 1 and 2) AS/NZS 3500.4:2003 Australian/New Zealand Standard Plumbing and drainage Part 4: Heated water services AS/NZS 3500.4:2003 This Joint Australian/New
Australian Standard. Emergency control organization and procedures for buildings, structures and workplaces AS 3745 2002
AS 3745 2002 (Incorporating Amendment Nos. 1 and 2) AS 3745 2002 Australian Standard Emergency control organization and procedures for buildings, structures and workplaces This Australian Standard was
Australian/New Zealand Standard
Australian/New Zealand Standard Quality systems Model for quality assurance in production, installation and servicing This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee
This is a free 9 page sample. Access the full version online. AS/NZS ISO 31000:2009 Risk management Principles and guidelines
AS/NZS ISO 31000:2009 Risk management Principles and guidelines AS/NZS ISO 31000:2009 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee OB-007, Risk Management. It was
Australian Standard. Customer satisfaction Guidelines for complaints handling in organizations (ISO 10002:2004, MOD) AS ISO 10002 2006
AS ISO 10002 2006 AS ISO 10002 2006 Australian Standard Customer satisfaction Guidelines for complaints handling in organizations (ISO 10002:2004, MOD) This Australian Standard was prepared by Committee
AS/NZS 4801:2001. Occupational health and safety management systems. Specification with guidance for use. Australian/New Zealand Standard
Australian/New Zealand Standard Occupational health and safety management systems Specification with guidance for use This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee
Australian Standard. Bridge design. Part 1: Scope and general principles AS 5100.1 2004 AP-G15.1/04 AS 5100.1
AS 5100.1 2004 AP-G15.1/04 AS 5100.1 Australian Standard Bridge design Part 1: Scope and general principles This Australian Standard was prepared by Committee BD-090, Bridge Design. It was approved on
AS 4775 2007 AS 4775 2007. Australian Standard. Emergency eyewash and shower equipment. This is a free 6 page sample. Access the full version online.
AS 4775 2007 AS 4775 2007 Australian Standard Emergency eyewash and shower equipment This Australian Standard was prepared by Committee SF-048, Emergency Eyewash and Shower Equipment. It was approved on
AS 5017 2006 AS 5017 2006. Australian Standard. Health Care Client Identification. This is a free 8 page sample. Access the full version online.
AS 5017 2006 AS 5017 2006 Australian Standard Health Care Client Identification This Australian Standard was prepared by Committee IT-014, Health Informatics. It was approved on behalf of the Council of
Australian Standard. General conditions of contract for design and construct. AS 4300 1995 (Incorporating Amendment No. 1)
AS 4300 1995 (Incorporating Amendment No. 1) Australian Standard General conditions of contract for design and construct This Australian Standard was prepared by Committee OB/3, General Conditions of Contract.
Australian/New Zealand Standard
AS/NZS 4105:1993 ISO/IEC 9805:1990/Cor.1:1991 Australian/New Zealand Standard Information technology Protocol specification for the commitment, concurrency and recovery service element AS/NZS 4105:1993
Australian Standard. Intruder alarm systems. Part 1: Systems installed in client s premises AS 2201.1 1998
AS 2201.1 1998 Australian Standard Intruder alarm systems Part 1: Systems installed in client s premises This Australian Standard was prepared by Committee EL/31, Intruder Alarm Equipment and Installations.
Australian/New Zealand Standard
AS/NZS 4187:2003 AS/NZS 4187 Australian/New Zealand Standard Cleaning, disinfecting and sterilizing reusable medical and surgical instruments and equipment, and maintenance of associated environments in
Software configuration management plans
AS 4042 1992 IEEE 828:1990 Australian Standard Software configuration management plans This Australian Standard was prepared by Committee IT/15, Software Engineering. It was approved on behalf of the Council
Australian Standard. Intruder alarm systems. Part 4: Wire-free systems installed in client s premises AS 2201.4 1990
AS 2201.4 1990 Australian Standard Intruder alarm systems Part 4: Wire-free systems installed in client s premises This Australian Standard was prepared by Committee EL/31, Intruder Alarm Equipment and
Australian/New Zealand Standard
AS/NZS 4236:1994 Australian/New Zealand Standard Respiratory therapy equipment Jet nebulizers and jet nebulizer air pumps AS/NZS 4236:1994 This Joint Australian/New Zealand Standard was prepared by Joint
Australian/New Zealand Standard
AS/NZS 4399:1996 Australian/New Zealand Standard Sun protective clothing Evaluation and classification AS/NZS 4399:1996 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee
Australian/New Zealand Standard
AS/NZS 3733:1995 Australian/New Zealand Standard Textile floor coverings Cleaning maintenance of residential and commercial carpeting AS/NZS 3733:1995 This Joint Australian/New Zealand Standard was prepared
Best Practice Board Reporting
HB 403 2004 Best Practice Board Reporting HB 403 2004 Handbook Best Practice Board Reporting First published as HB 403 2004. COPYRIGHT Standards Australia International All rights are reserved. No part
Australian Standard. Guide to lead paint management. Part 2: Residential and commercial buildings AS 4361.2 1998
AS 4361.2 1998 Australian Standard Guide to lead paint management Part 2: Residential and commercial buildings This Australian Standard was prepared by Committee CH/3, Paint and Related Materials. It was
Australian Standard. Interactive voice response systems user interface Speech recognition AS 5061 2008 AS 5061 2008
AS 5061 2008 AS 5061 2008 Australian Standard Interactive voice response systems user interface Speech recognition This Australian Standard was prepared by Committee IT-022, Interactive Voice Response
Australian Transport Council. National Standard for the Administration of Marine Safety SECTION 4 SURVEYS OF VESSELS
Australian Transport Council National Standard for the Administration of Marine Safety SECTION 4 SURVEYS OF VESSELS Edition 1 Draft for comment issued 20 December 2005 Endorsed by the Australian Transport
Fraud and Corruption Control
AS 8001 2003 Australian Standard Fraud and Corruption Control This Australian Standard was prepared by Committee MB-004, Business Governance. It was approved on behalf of the Council of Standards Australia
august09 tpp 09-05 Internal Audit and Risk Management Policy for the NSW Public Sector OFFICE OF FINANCIAL MANAGEMENT Policy & Guidelines Paper
august09 09-05 Internal Audit and Risk Management Policy for the NSW Public Sector OFFICE OF FINANCIAL MANAGEMENT Policy & Guidelines Paper Preface Corporate governance - which refers broadly to the processes
COMMUNICATIONS ALLIANCE LTD DOCUMENT MAINTENANCE POLICY AND PROCESS
COMMUNICATIONS ALLIANCE LTD DOCUMENT MAINTENANCE POLICY AND PROCESS Revised: May 2008 - 2 - TABLE OF CONTENTS 1 INTRODUCTION 3 2 COMMUNICATIONS ALLIANCE DOCUMENT REVIEW POLICY 3 3 COMMUNICATIONS ALLIANCE
HB 292 2006 A Practitioners Guide to Business Continuity Management
HB 292 2006 A Practitioners Guide to Business Continuity Management HB HB 292 2006 Handbook A practitioners guide to business continuity management First published as HB 292 2006. COPYRIGHT Standards Australia
Agency Management of Software Licensing
The Auditor-General Audit Report No.27 2001 2002 Assurance and Control Assessment Audit Agency Management of Software Licensing Australian National Audit Office Commonwealth of Australia 2001 ISSN 1036-7632
Australian Standard. Amended from AS 2124-1992
AS 224 992 with AS 225 992 AS 227 992 (Incorporating Amendment No. ) Australian Standard General conditions of contract (AS 224 992) together with General conditions of tendering and form of tender (AS
Ambient air - Standard gravimetric measurement method for the determination of the PM10 or PM2,5 mass concentration of suspended particulate matter
Irish Standard I.S. EN 12341:2014 Ambient air - Standard gravimetric measurement method for the determination of the PM10 or PM2,5 mass concentration of suspended particulate matter CEN 2014 No copying
Regulatory Burdens Social & Economic Infrastructure Services
Productivity Commission Regulatory Burdens Social & Economic Infrastructure Services Submission by Christian Schools Australia Ltd For further discussion regarding this submission please contact: Stephen
Australian Transport Council. National Standard for the Administration of Marine Safety SECTION 5
Australian Transport Council National Standard for the Administration of Marine Safety SECTION 5 APPROVAL AND AUDITING OF REGISTERED TRAINING ORGANISATIONS August 2008 First Published: August 2008 Endorsed
Charities Bill 2013 and the Charities (Consequential Amendments and Transitional Provisions) Bill 2013
3 May 2013 Manager Philanthropy and Exemptions Unit Indirect, Philanthropy and Resource Tax Division The Treasury Langton Crescent PARKES ACT 2600 By email: charities@treasury.gov.au Dear Treasury Charities
Software quality assurance in Australia D. Wilson School of Computing Sciences, University of Technology, /, fo Boz
Software quality assurance in Australia D. Wilson School of Computing Sciences, University of Technology, /, fo Boz ABSTRACT This paper will trace the history of the software quality assurance (SQA) movement
Metallic products Types of inspection documents
BRITISH STANDARD BS EN 10204:2004 Metallic products Types of inspection documents The European Standard EN 10204:2004 has the status of a British Standard ICS 01.110; 77.080.01; 77.120.01 BS EN 10204:2004
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61892-1 First edition 2001-12 Mobile and fixed offshore units Electrical installations Part 1: General requirements and conditions Unités fixes et mobiles en mer Installations
Drinking Water Quality Management Plan Review and Audit Guideline
Drinking Water Quality Management Plan Review and Audit Guideline This publication has been compiled by Queensland Water Supply Regulator, Department of Energy and Water Supply. State of Queensland, 2013.
Privacy fact sheet 17
Privacy fact sheet 17 Australian Privacy Principles January 2014 From 12 March 2014, the Australian Privacy Principles (APPs) will replace the National Privacy Principles Information Privacy Principles
Grant Programme Guidelines Community Development Grants Programme
Grant Programme Guidelines Community Development Grants Programme Community Development Grants Programme Guidelines Contents Process Flowchart... 3 1. Introduction... 4 1.1. Programme Background... 4 1.2.
Custodian-Node data provision terms and conditions
Custodian-Node data provision terms and conditions Parties Node Operator Data Custodian Background A B C D E [Insert legal name of node][insert ACN/ABN/ARBN] of [Insert address]\ [Insert legal name of
RULE COMPARISON TABLE
RULE COMPARISON TABLE This comparison table provides guidance as to how the new ASX Operating Rules (new Rules) correspond to the old ASX Market Rules (old Rules). The old Rules are in black in the left
Commonwealth of Australia 2003
Import Risk Analysis Handbook Canberra, 2003 Commonwealth of Australia 2003 This work is copyright. You may download, display, print and reproduce this material in unaltered form only (retaining this notice)
You should distribute the completed learning plan to the team and forward a copy to the human resources team. Name: Section: Location:
Implement learning plans Encourage a learning environment what work, if any, will be missed by the learners during the program cost of the program resources required to conduct the program language, literacy
Workplace Health and Safety Amendment Regulation (No. 1) 2011
Queensland Workplace Health and Safety Amendment Regulation (No. 1) 2011 Explanatory Notes for SL 2011 No. 55 made under the Workplace Health and Safety Act 1995 General outline Short title Workplace Health
NZS 3910:2013. Conditions of contract for building and civil engineering construction NZS 3910:2013. New Zealand Standard
New Zealand Standard Conditions of contract for building and civil engineering construction Superseding (in part) NZS 3910:2003 NZS 3910:2013 COMMITTEE REPRESENTATION This Standard was prepared under the
In the latter half of 2011, AIB assisted ACIF to develop a Work Health and Safety (WHS policy), and this is listed in Appendix 1.
Australian Institute of Building Submission to the Draft Australian Work Health and Safety Strategy 2012 2022: Healthy, Safe and Productive Working Lives Introduction The Australian Institute of Building
The Development of Statements of Accounting Concepts and Accounting Standards
Policy Statement 1 (7/93) The Development of Statements of Accounting Concepts and Accounting Standards Prepared by the Public Sector Accounting Standards Board of the Australian Accounting Research Foundation
Food Safety. Management Systems. Scope of Accreditation
Publication Reference EA-3/11 M: 2009 Food Safety Management Systems Scope of Accreditation PURPOSE This document outlines the EA policy for accreditation bodies when processing accreditation to certification
Registration standard: Endorsement as a nurse practitioner
Registration standard: Endorsement as a nurse practitioner Consultation report February 2016 Nursing and Midwifery Board of Australia G.P.O. Box 9958 Melbourne VIC 3001 www.nursingmidwiferyboard.gov.au
BUSINESS CONTINUITY MANAGEMENT
BUSINESS CONTINUITY MANAGEMENT Handbook Business Continuity Management Originated as HB 221:2003. Second edition 2004. COPYRIGHT Standards Australia/Standards New Zealand All rights are reserved. No part
Workplace first aid kits
BS 8599-1:2011 BSI Standards Publication NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW raising standards worldwide Workplace first aid kits Part 1: Specification for the contents
Application of ISO/IEC 17011 for the Accreditation of Food Safety Management Systems (FSMS) Certification Bodies
IAF Mandatory Document Application of ISO/IEC 17011 for the Accreditation of Food Safety Management Systems (FSMS) Certification Bodies (IAF MD 16:2015) Version 2 Food Safety Management Systems (FSMS)
Submission by the Commonwealth Ombudsman
Submission by the Commonwealth Ombudsman INQUIRY INTO NATIONAL REGISTRATION AND ACCREDITATION SCHEME FOR DOCTORS AND OTHER HEALTH WORKERS Submission to the Senate Community Affairs Committee by the Commonwealth
Guide to Assessment and Rating for Services
Guide to Assessment and Rating for Services August 2014 Copyright The details of the relevant licence conditions are available on the Creative Commons website (accessible using the links provided) as is
Records and Document Management
Records and Document Management Policy P3 Current: Updated November 2011 Table of Contents Purpose... 3 Scope... 3 Definitions... 3 Policy statement... 4 Responsibility... 4 Legislative context... 5 Associated
General Records Authority
General Records Authority Transfer of custody and ownership of Personal Security Files (PSFs) Job no 2008/00174731 18 April 2008 Commonwealth of Australia 2008 This work is copyright. Apart from any use
Records Disposal Schedule Anti-Discrimination Services Northern Territory Anti-Discrimination Commission
Records disposal schedule Records Disposal Schedule Anti-Discrimination Services Northern Territory Anti-Discrimination Commission Disposal Schedule No. 2015/12 August 2015 NT Archives Service For information
FSDF SPATIAL INFORMATION MANAGEMENT POLICIES - CUSTODIANSHIP
FSDF SPATIAL INFORMATION MANAGEMENT POLICIES - CUSTODIANSHIP Objective: To provide consistent custodial arrangements so that spatial information is managed to appropriate standards and made available in
Information Paper. Superannuation Trustee Liability Insurance. www.apra.gov.au Australian Prudential Regulation Authority.
Information Paper Superannuation Trustee Liability Insurance 30 June 2006 www.apra.gov.au Australian Prudential Regulation Authority Copyright The material in this Publication is copyright. You may download,
CERTIFICATION REQUIREMENTS QUALIFICATION-BASED QUALITY MANAGEMENT SYSTEMS (QMS) AUDITOR CERTIFICATION PROGRAM
CERTIFICATION REQUIREMENTS QUALIFICATION-BASED QUALITY MANAGEMENT SYSTEMS (QMS) AUDITOR CERTIFICATION PROGRAM Exemplar Global Personnel Certification Programs Exemplar Global is accredited by the Joint
Dodo Power & Gas Complaint Management Policy
DODO POWER & GAS PTY LTD Dodo Power & Gas Complaint Management Policy Jurisdiction: All 2013 Policy Reference ref DPG 100-004 Version: 1.2 Author: Status Andrew Mair Draft Publication Date 7/06/2013 Location:
Compendium of OHS and Workers Compensation Statistics. December 2010 PUTTING YOU FIRST
Compendium of OHS and Workers Compensation Statistics December 2010 PUTTING YOU FIRST Disclaimer This Compendium has been developed by Comcare and all attempts have been made to incorporate accurate information
New South Wales State and Regional Population Projections 2001-2051. 2004 Release TRANSPORT AND POPULATION DATA CENTRE
New South Wales State and Regional Population Projections 21-251 251 24 Release TRANSPORT AND POPULATION DATA CENTRE THE TRANSPORT AND POPULATION DATA CENTRE (TPDC) The TPDC is located in the NSW Department
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60812 Second edition 2006-01 Analysis techniques for system reliability Procedure for failure mode and effects analysis (FMEA) This English-language version is derived from the
Client Skills: Skills required by Government as the Construction Industry Client
Client Skills: Skills required by Government as the Construction Industry Client APCC MEMBER AUTHORITIES AS AT JULY 2002 Department of Public Works and Services New South Wales Building Commission Victoria
Essential Standards for Registration
Essential Standards for Registration State and Territory Registering Bodies Australian Capital Territory New South Wales Northern Territory Queensland South Australia Tasmania Victoria Western Australia
ISO 9001:2008 Quality Management System Requirements (Third Revision)
ISO 9001:2008 Quality Management System Requirements (Third Revision) Contents Page 1 Scope 1 1.1 General. 1 1.2 Application.. 1 2 Normative references.. 1 3 Terms and definitions. 1 4 Quality management
EP 95 00 30 03 SP RAILCORP NETWORK MANAGEMENT PLAN CHAPTER 2 - CUSTOMER INSTALLATION SAFETY. Authorised by: Neal Hook Chief Engineer Electrical
Engineering Standard Electrical RAILCORP NETWORK MANAGEMENT PLAN CHAPTER 2 - CUSTOMER INSTALLATION SAFETY Owner: Approved by: Chief Engineer, Electrical Neal Hook Chief Engineer Electrical Authorised by:
CPSU (PSU Group) Submission regarding the Draft model Work Health and Safety (WHS) Regulations and model Codes of Practice
CPSU (PSU Group) Submission regarding the Draft model Work Health and Safety (WHS) Regulations and model Codes of Practice April 2011 2 Introduction The Community and Public Sector Union (CPSU) welcomes
INTERNATIONAL SUPPLY CONTRACT TEMPLATE
INTERNATIONAL SUPPLY CONTRACT TEMPLATE Download International Supply Contract sample in Word format. Fill in the blanks and choose the terms of this international agreement that best suit your needs. DATE:...
75 YEARS OF WORKING TO BUILD A HEALTHY AUSTRALIA NHMRC
75 YEARS OF WORKING TO BUILD A HEALTHY AUSTRALIA NHMRC Research Funding Facts Book 2011 75 YEARS OF WORKING TO BUILD A HEALTHY AUSTRALIA NHMRC Research Funding Facts Book 2011 Australian Government 2011
Memorandum of Understanding between the NSW Ministry of Health and Sydney Water Corporation
Page 1 of 11 Memorandum of Understanding between the NSW Ministry of Health and Sydney Water Corporation This work is copyright. It may be reproduced in whole or in part for study or training purposes
Chain of Custody of Forest Based Products - Requirements
PEFC INTERNATIONAL STANDARD Requirements for PEFC scheme users PEFC ST 2002:2013 2012-12-04 Enquiry Draft Chain of Custody of Forest Based Products - Requirements PEFC Council World Trade Center 1, 10
STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND. Committee CE-001 Parking Facilities DRAFT. Australian/New Zealand Standard
Draft For Committee Purposes Only DRAFT FOR SUBMISSION TO ABCB CE/001/09-481A (Supersedes CE/001/05-406) Issued: February 2009 Project No: 5431 STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Committee CE-001
Managing Occupational Health and Safety on Queensland Government Building Projects A Management Systems Approach D Evans
OCCUPATIONAL HEALTH AND SAFETY THE CARING CLIENT? Case Study MANAGING OCCUPATIONAL HEALTH AND SAFETY ON QUEENSLAND GOVERNMENT BUILDING PROJECTS A MANAGEMENT SYSTEMS APPROACH David Evans Queensland Department
Framework for the Development of Food Safety Program Tools July 2001
Food Safety: Frameork for the Development of Food Safety Program Tools July 2001 Australia Ne Zealand Food Authority 2001 ISBN 0 642 34548 1 First published July 2001 This ork is copyright. Apart from
Assessor Advice Re: CPC and CPC08 Training Packages
373 Elizabeth Street North Hobart, Tasmania 7000 PO Box 547 North Hobart, Tasmania 7002 03 6218 2841 enquiries@artibus.com.au www.artibus.com.au Assessor Advice Re: CPC and CPC08 Training Packages Artibus
Form 18 Application for a Queensland electrical contractor licence
Electrical Safety Office Form 18 Application for a Queensland electrical contractor licence V17.06-2014 Electrical Safety Act 2002 INSTRUCTIONS: Read the guidelines when completing this application form.
A guide to the water charge (infrastructure) rules: Tier 2 requirements
A guide to the water charge (infrastructure) rules: Tier 2 requirements June 2011 Australian Competition and Consumer Commission 23 Marcus Clarke Street, Canberra, Australian Capital Territory, 2601 Commonwealth
WELS Compliance Risk Management Guide For Suppliers
WELS Compliance Risk Management Guide For Suppliers A working document (March 2007) A Working Document This is a WELS Compliance Risk Management working document. Prepared by the Water Policy Branch Department
the instructions to those forms, all of which are attached and form part of this reporting standard.
Reporting Standard RRS 394.0 Personal Finance Objective of this reporting standard This reporting standard is made under section 13 of the Financial Sector (Collection of Data) Act 2001. It applies to
National Partnership Agreement to Deliver a Seamless National Economy (SNE NP) Report card prepared by the COAG Business Advisory Forum Taskforce
National Partnership Agreement to Deliver a Seamless National Economy (SNE NP) Report card prepared by the COAG Business Advisory Forum Taskforce - April 2013 - Overview In 2008, COAG agreed to implement
Privacy Policy Fletcher Building Limited and Fletcher Building (Australia) Pty Ltd
Privacy Policy Privacy Policy Fletcher Building Limited and Fletcher Building (Australia) Pty Ltd What is this privacy policy about? This Privacy Policy describes how Fletcher Building Limited and Fletcher
Quality Assurance. Policy P7
Quality Assurance Policy P7 Table of Content Quality assurance... 3 IIA Australia quality assurance and professional standards... 3 Quality assurance and professional qualifications... 4 Quality assurance
ACMA Determination Submission
Submission ACMA Determination Submission Queensland Police Service response to an invitation to comment on the draft Telecommunications (Emergency Call Service) Determination 2009, issued June 2009. Introduction