INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Keefe Widespread Lavatory Faucet Model D0800 Thank you for selecting DXV by American Standard. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin. RECOMMENDED TOOLS AND MATERIALS Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing, supply stores. It is essential that the tools and materials be on hand before work is begun. Tubing Cutter Channel Locks ROUGHING-IN DIMENSIONS: For reference -/8" (.mm) 7/8" DIA. (mm) -/ O.D. (mm) 7" MAX. (78mm) -/0" (.9mm) MAX " (mm) Basin Wrench Adjustable Wrench -/8" (.7mm) -/" DIA. (9mm) CONNECTIONS ARE FOR /" IPS (8mm) FLEXIBLE SUPPLIES or /8" O.D. (0mm) BULL-NOSE RISERS Plumbers' Putty or Caulking " TO " MAX. (mm TO 0mm MAX.) -/" (8mm) -/" MAX. (8mm) Phillips Screwdriver Flat Blade Screwdriver -7/8" (98.mm) -/" MAX. (mm) NOTE: MOUNTING HOLES ARE -/8" DIA. (mm) for Spout and for Side valve S A V E F O R F U T U R E U S E In the United States: DXV by American Standard One Centennial Avenue Piscataway, New Jersey 088 Attention: Director of Customer Care For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) In Canada: DXV by American Standard 900 Avebury Road Mississauga, Ontario LR M Canada Toll Free: Local: Fax: In Mexico: DXV by American Standard Via Morelos 0 Col. Santa Clara Coatitla Ecatepec, Estado de México 0 Toll Free: Product names listed herein are trademarks of AS America, Inc. AS America, Inc M980 Rev..

2 SPOUT ASSEMBLY CAUTION Turn off hot and cold water supplies before beginning. Insert SPOUT () and CABLE CONNECTOR () through center hole, making sure SEAL WASHER () is properly seated in SPOUT BASE () groove. Assemble RUBBER WASHER (), BRASS WASHER () and LOCKNUT (7) onto SPOUT SHANK (8) from under side of sink. Make sure SPOUT () is centered in the mounting hole and the slot in the BRASS WASHER () faces toward the rear of the sink. Tighten LOCKNUT (7) firmly. SLOT 8 7 TEE ASSEMBLY Thread TEE BODY () COUPLING NUT () to SPOUT SHANK (). REMOVE HANDLE ASSEMBLIES FROM VALVE BODIES HANDLE ASSEMBLIES () are installed on VALVE BODIES () and must be removed to install VALVE BODIES () into mounting holes. To remove HANDLE ASSEMBLY (), unthread HANDLE BASE () with LEVER () from VALVE BODY (). Pull HANDLE ASSEMBLY () off VALVE STEM (). Unthread and remove MOUNTING RING () and SPACER (7). INSTALL VALVE BODIES 7 Thread LOCKNUT () to bottom of VALVE BODY (). Make sure RUBBER WASHER () is installed. Insert VALVE BODY () through mounting hole from underside of lavatory or mounting surface. Note: VALVE BODY marked Hot is installed in the left mounting. hole, VALVE BODY marked Cold in the right when facing front of fitting. Maximum mounting surface thickness is -/". From top install SPACER () onto VALVE BODY (). Thread MOUNTING RING () with seal to VALVE BODY () until seated tightly against stop. Set VALVE BODIES () so that their outlets are facing toward SPOUT TEE () and then tighten LOCKNUT () using wrench or other approprite wrench to secure VALVE BODIES () to mounting surface. TUB DECK OR MOUNTING SURFACE -/" MAX. HOT - - M980 Rev..

3 INSTALL HANDLES AND SUPPLY HOSES INSTALL HANDLES Turn VALVE STEMS () to off position. Align LEVERS () as shown or as desired and install HANDLE ASSEMBLY () onto VALVE STEM (). Thread HANDLE BASE () clock-wise onto VALVE BODY THREADS (a) until seated tightly against mounting surface and aligned with the dotted line in the illustration. INSTALL SUPPLY HOSES Thread supply hose COUPLING NUTS () onto outlets on VALVE BODIES (). Tighten with an adjustable wrench making a water tight connection. Important: Loop SUPPLY HOSES (7) as illustrated so they do not kink. 7 a INSTALL POP-UP Remove CLEAR PLASTIC COVER (). Fig. A. Remove FOAM SPACER () from under POP-UP (). Fig. A. Fig. A. BODY Tighten TAILPIECE () on BODY before installing BODY. 7 REMOVE MOUNTING WASHERS AND LOCKNUT Fig. A. REAR OF SINK Thread LOCKNUT () counter-clockwise and remove from drain body. Remove PLASTIC WASHER () and pull off RUBBER CONE WASHER () Fig. A. Drop BODY () through sink drain hole. Make sure WHITE FOAM GASKET () is under flange of BODY (). Note: No plumber s putty or caulk is required. The CABLE ATTACHMENT POINT () must face towards the rear of the SINK. SINK HOLE 8 ATTACH FROM 9 TIGHTEN LOCKNUT BELOW FIXTURE From under side of SINK install RUBBER CONE WASHER (), PLASTIC WASHER () and LOCKNUT () onto BODY (). Note: The CABLE ATTACHMENT POINT () must face towards the rear of the SINK. Tighten LOCKNUT () firmly with Adjustable Wrench or Channel Locks. - - M980 Rev..

4 0 FLANGE GASKET AND POP-UP KNOB Check FLANGE in SINK to ensure that WHITE FOAM GASKET () is fully compressed and not visible. Fig. A. Fig. A. DOWN POP-UP KNOB () must be fully down. WHITE WHITE FOAM FOAM GASKET NOT NOT VISIBLE FLANGE UP ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR () clockwise onto BODY CONNECTION () and hand tighten. Fig. A. Fig. A. Your new POP-UP installation is now complete. Note: Tailpiece on pop-up drain is -/" O.D. -/ O.D. CHECK OPERATION OF POP-UP Operate LIFT KNOB () to verify that STOPPER () opens and closes. Note: If STOPPER () does not open and close properly then refer to the troubleshooting section of these instructions. MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. Connect water supply to VALVE BODIES (, A) with /" IPS FLEXIBLE SUPPLIES () or /8" O.D. BULL-NOSE RISERS (). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. /" PIPE THREAD FLEXIBLE SUPPLIES /8 O.D. BULL-NOSE RISERS COLD COUPLING NUT A COMPRESSION NUT FERRULE HOT /8 COMPRESSION CONNECTION - - M980 Rev..

5 CONNECT Connect -/" O.D. tailpiece on POP-UP to waste outlet. WASTE OUTLET -/" O.D. TAILPIECE TEST INSTALLED FITTING With HANDLES () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. CHECK CONNECTIONS Operate POP-UP KNOB () and fill Sink with water. Check that STOPPER () makes a good seal and retains water in Sink. If STOPPER () does not seal properly, please refer to Troubleshooting Guide in these instructions. Push POP-UP KNOB () down and check all drain connections and "P" trap for leaks. Tighten if necessary. WASTE OUTLET HOT COLD P TRAP - - M980 Rev..

6 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position: Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode. CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration. Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C. Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C. Re-attach the Cable to the Drain Body Connection () by threading the Cable Connector () clockwise onto the Drain Body Connection () and hand-tighten. Fig. A. Fig. A. Fig. C. DOWN RE-ATTACH CAM DISCONNECT CAM CAP STOPPER STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. Fig. D. Fig. E. Fig. F. REMOVE CAM REMOVE CAM CAP - - M980 Rev..

7 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, Locked Mode (Stopper cannot be removed) or Unlock Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. Fig. G. To install the stopper in Locked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.fig. G. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troubling Shooting Guide to complete installation. Stopper will be in Locked mode and not be removable. LOOP TOWARD REAR OF SINK Locked Mode (Vandal Proof) Unlocked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H. To install the stopper in Unlocked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. LOOP TOWARD FRONT OF SINK 80 Unlocked Mode Fig. H. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troublingshooting Guide to complete installation. Stopper will be in Unlocked mode and removable. Fig. J. Fig. K. CAM INSTALL CAM INSTALL CAM CAP M980 Rev..

8 Keefe Widespread Lavatory Faucet MODEL NUMBER D0800 M98-YYY0A LIFT KNOB ASSEMBLY M9-YYY0A HANDLE KIT M A SPOUT SEAL M A CHECK VALVE H908.9 DECK ADAPTER KIT H900.9 /" HOT CARTRIDGE (COUNTER CLOCK-WISE ON) H907.9 /" SIDE VALVE ROUGH (COUNTER CLOCK-WISE ON) H MOUNTING KIT M A TEE & HOSE ASSEMBLY H909.9 SPOUT MOUNTING KIT M A SPEED CONNECT CABLE ASSEMBLY H90.9 /" COLD CARTRIDGE (CLOCK-WISE ON) H907.9 /" SIDE VALVE ROUGH (COUNTER CLOCK-WISE ON) Replace the "YYY" with appropriate finish code POLISHED CHROME BRUSHED NICKEL PLATINUM NICKEL XXX ASSEMBLY M980 Rev..