Sample Size Determination

Transcription

1 Sample Size Determination Bandit Thinkhamrop, PhD (Statistics) Dept. of Biostatistics & Demography Khon Kaen University

2 Essential of sample size calculation No one accept any magic number Too large vs Too small To justify with the sponsor and the Ethics Committee To ensure: adequate power to test a hypothesis desired precision to obtain an estimate

3 Two main approaches Hypothesis-based sample size calculation Involve power or beta error Ensure a significant finding but may not be conclusive clinically Easy and widely available Confidence interval methods of sample size calculation Involve precision of the estimation Ensure a conclusive finding clinically as this method is directly estimate the magnitude of effect Difficult and not widely available

4 Overall steps Identify the primary outcome Identify and review the magnitude of effect and its variability that will be used as the basis of the conclusion of the research. Identify what statistical method that will be used to obtain the main magnitude of effect. Calculate the sample size Describe how the sample size is calculated with sufficient details that allow explicability.

5 Steps in the calculation Base sample size calculation Design effect (for correlated outcome) Contingency (increase to account for nonresponses or dropout) Rounding up to a nearest (and comfortable) number Evaluate if this sample size would provide a precise and conclusive answer to the research question by analyze the data as if it is as expected.

6 Suggested approaches For unknown parameters in the formula, try to find existing evidences or use your best GUESTIMATE, a.k.a. educated guest. Do not use only one scenario or based on only one reference fro the calculation. It is highly recommended that all key parameters should be varied to see how they effect on the sample size. Always evaluate its sufficiency by estimate the main magnitude of effect and its 95% CI and see if it provide a conclusive finding. Consult with the statistician early

7 Common pitfalls Unjustified sample size by specifying a magic number Based on a simplify formula or a sample size table without understanding its limitations "A previous study in this area recruited 50 subjects and found highly significant results (p=0.001), and therefore a similar sample size should be sufficient." never do it like this Inconsistent with the protocol Too much rely on the previous findings in sample size calculation

8 Examples of common calculations Mean one group Mean two independent groups Proportion one group Proportion two independent groups Get some idea from those Practice with your own research

9 Mean one group :Formula Where: n = The sample size Z /2 = The standard normal coefficient, typically 1.96 for 95% CI s =The standard deviation. d = The desired precision level expressed as half of the maximum acceptable confidence interval width.

10 Mean one group :Calculations (fix = 0.05) Expected Standard deviation Precision (half width) n

11 Mean one group :Descriptions A sample size of 38 would be able to estimate a mean with a precision of 10 assuming a standard deviation of 30 according to a study by <Reference>. That is, based on the expected mean of 55 <Reference>, the 95% confidence interval of the estimated mean would be between 45 and 65.

12 Mean two independent group :Formula Sample size in each group (assumes equal sized groups) Represents the desired power (typically.84 for 80% or 1.28 for 90% power) A measure of variability (This is a variance or a square of the standard deviation) Represents the desired level of statistical significance (typically 1.96 for = 0.05). Minimum meaningful difference or Effect Size

13 Mean two independent groups :Calculations (fix = 0.05) H0: M1-M2=0. H1: M1-M2=D1<>0. Test Statistic: Z test with pooled variance (SD1 = 20; SD2 = 25) Power Mean in Control grp. Minimum and meaningful difference 90% % % % % % % % n1 n2

14 Mean two independent groups :Descriptions A total sample size of 37 in group one and 37 in group two would have a power of 80% to detect a difference between group of 15 assuming a mean of 35 in control group with estimated group standard deviations of 20 and 25, respectively, according to a study by <Reference>. The test statistic used is the two-sided two sample t-test. The significance level of the test was targeted at 0.05.

15 Proportion one group :Formula Where: n = The sample size Z /2 = The standard normal coefficient,, typically 1.96 for 95% CI p = The value of the proportion as a decimal percent (e.g., 0.45). d = The desired precision level expressed as half of the maximum acceptable confidence interval width.

16 Proportion one group :Calculations (fix = 0.05) Expected Prevalence Precision (half width) 15% 2% 1,225 20% 2% 1,537 15% 4% % 4% 385 n

17 Proportion one group :Descriptions A sample size of 400 would have a 95% confidence interval of 16% to 24% assuming a prevalence of 20% according to a study by <Reference>.

18 Proportion two independent group :Formula Sample size in each group (assumes equal sized groups) Represents the desired power (typically.84 for 80% or 1.28 for 90% power) A measure of variability (similar to standard deviation) Represents the desired level of statistical significance (typically 1.96 for = 0.05). Minimum meaningful difference or Effect Size

19 Proportion two independent groups :Calculations (fix = 0.05) H0: P1-P2=0. H1: P1-P2=D1<>0. Test Statistic: Z test with pooled variance Power Proportion in Control grp. Minimum and meaningful difference 90% 40% 5% 2,053 2,053 80% 40% 5% 1,534 1,534 90% 50% 5% 2,095 2,095 80% 50% 5% 1,565 1,565 90% 40% 10% % 40% 10% % 50% 10% % 50% 10% n1 n2

20 Proportion two independent groups :Descriptions A total sample size of 388 in group one and 388 in group two would have a power of 80% to detect a difference between group of 10% assuming a prevalence of 50% in control group according to a study by <Reference>. The test statistic used is the two-sided Z test. The significance level of the test was targeted at

21 Other considerations Sampling design affects the calculation of sample size Simple random sampling / assignment Stratified random sampling / assignment Clustered random sampling / assignment Complex study designs affects the calculation of sample size Matching Multiple stages of sampling Repeated measures Usually the sample size calculation is based on method of analysis Correlation, Agreement, Diagnostic performance Z-test Regression multiple linear, logistic Multivariate analyses such as principle component or factor analysis Survival analyses Multilevel models

22 Other considerations Demonstrate superiority Sample size sufficient to detect difference between treatments Require to specify minimum meaningful difference Demonstrate non-inferiority or equally effective Sample size required to demonstrate equivalence larger than required to demonstrate superiority Require to specify non-inferiority margin or equivalence range

23 Precision or Power Estimation Equivalence to sample size calculation do it in the planning phase of the study Do it when the number of available sample is known Wrong: There are around 50 patients per year, of whom 10% may refuse to take part in the study. Therefore over the 2 years of the study, the sample size will be 90 patients. Correct: It is estimated that there will be 90 patients in the clinic. This will give a precision of the prevalence estimation of 20% assuming a prevalence of 65%.

24 Suggested learning resources WWW: Statistics Guide for Research Grant Applicants at St George s University of London (maintained by Martin Bland): Software: PASS, nquery, EpiTable, SeqTrial, PS, etc.

25 Q & A