absolute maximum ratings at 25 C case temperature (unless otherwise noted) OBSOLETE

Transcription

1 , A Rugged Triple-Diffused Planar Construction 9 A Continuous Collector Current 1000 olt Blocking Capability B SOT-93 PACKAGE (TOP IEW) 1 C 2 E 3 Pin 2 is in electrical contact with the mounting base. MDTRAAA absolute maximum ratings at 25 C case temperature (unless otherwise noted) RATING SYMBOL ALUE UNIT Collector-emitter voltage ( BE = -2.5 ) 850 CEX A 1000 Collector-emitter voltage (R BE = 10 Ω) 850 CER A 1000 Collector-emitter voltage ( = 0) 400 CEO A 450 Continuous collector current 9 A Peak collector current (see Note 1) M 15 A Continuous base current 3 A Peak base current M 6 A Continuous device dissipation at (or below) 25 C case temperature P tot 120 W Operating junction temperature range T j -65 to +150 C Storage temperature range T stg -65 to +150 C NOTE 1: This value applies for 5 ms, duty cycle 2%. 1

2 , A electrical characteristics at 25 C case temperature (unless otherwise noted) PARAMETER TESONDITIONS MIN TYP MAX UNIT CEO(sus) Collector-emitter 400 I sustaining voltage C = 200 ma L = 25 mh (see Note 2) A 450 (BR)EBO Base-emitter breakdown voltage I E = 50 ma = 0 (see Note 3) 7 30 CE = 850 BE = ES Collector-emitter CE = 1000 BE =0 A 0.15 cut-off current CE = 850 BE =0 = 125 C 1.5 ma CE = 1000 BE =0 = 125 C A 1.5 CE = 850 R BE =10 Ω 0.4 ER Collector-emitter CE = 1000 R BE =10 Ω A 0.4 cut-off current CE = 850 R BE =10 Ω = 125 C 3.0 ma CE = 1000 R BE =10 Ω = 125 C A 3.0 I EBO Emitter cut-off current EB = 5 =0 1 ma CE(sat) Collector-emitter = 1 A = 5A 1.5 (see Notes 3 and 4) saturation voltage = 2.5 A = 8A 3.0 BE(sat) Base-emitter saturation voltage = 1 A = 5A (see Notes 3 and 4) 1.6 f t Current gain bandwidth product CE = 10 = 0.5 A f = 1 MHz 8 MHz C ob Output capacitance CB = 20 = 0 f = 0.1 MHz 105 pf NOTES: 2. Inductive loop switching measurement. 3. These parameters must be measured using pulse techniques, = 300 µs, duty cycle 2%. 4. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts. thermal characteristics PARAMETER MIN TYP MAX UNIT R θjc Junction to case thermal resistance 1 C/W resistive-load-switching characteristics at 25 C case temperature PARAMETER TESONDITIONS MIN TYP MAX UNIT t on Turn on time 1.0 µs = 5 A (on) = 1 A (off) = -1 A t s Storage time 3.0 µs CC = 150 (see Figures 1 and 2) t f Fall time 0.8 µs oltage and current values shown are nominal; exact values vary slightly with transistor parameters. inductive-load-switching characteristics at 25 C case temperature (unless otherwise noted) PARAMETER TESONDITIONS MIN TYP MAX UNIT t sv oltage storage time = 5 A (on) = 1 A BE(off) = µs t fi Current fall time = 100 C (see Figures 3 and 4) 0.4 µs 2

3 , A PARAMETER MEASUREMENT +25 T BD Ω 680 µ F 100 Ω 1 47 Ω 100 µf cc = CC Ω TUT = 20 µs Duty cycle = 1% 1 = 15, Source Impedance = 50 Ω A - B = t d B - C = t r E - F = t f D - E = t s A - C = t on D - F = t off Ω BD Ω 680 µ F Figure 1. Resistive-Load Switching Test Circuit B C D E F (on) 0% d 2 A/µs dt A 0% (off) Figure 2. Resistive-Load Switching Waveforms 3

4 , A PARAMETER MEASUREMENT 33 Ω +5 BY D45H11 Gen 68 Ω 1 pf 1 k Ω 33 Ω BY N2222 RB (on) 0.02 µf TUT 1 k Ω 180 µh v cc BY clamp = 400 A - B = t sv B - C = t rv D - E = t fi +5 5X BY Ω BY k Ω 2N2904 Adjusw to obtain For < 6 A CC = 50 For 6 A CC = 100 (on) 47 Ω 100 Ω D44H11 BE(off) Figure 3. Inductive-Load Switching Test Circuit A () Base Current E - F = t ti B - E = t xo C CE B Collector oltage D () (on) E () F (2%) Collector Current NOTES: A. Waveforms are monitored on an oscilloscope with the following characteristics: t r < 15 ns, R in > 10 Ω, C in < 11.5 pf. B. Resistors must be noninductive types. Figure 4. Inductive-Load Switching Waveforms 4

5 , A TYPICAL CHARACTERISTICS h FE - Typical DC Current Gain CE(sat) - Collector-Emitter Saturation oltage TYPICAL DC CURRENT GAIN COLLECTOR CURRENT Collector Current - A TCP762AA CE = 5 = 125 C = 25 C = -65 C COLLECTOR-EMITTER SATURATION OLTAGE BASE CURRENT Base Current - A Figure 5. Figure 6. COLLECTOR-EMITTER SATURATION OLTAGE BASE CURRENT TCP762AK = 100 C = 8 A = 6 A = 4 A = 2 A CE(sat) - Collector-Emitter Saturation oltage TCP762AB = 25 C = 8 A = 6 A = 4 A = 2 A COLLECTOR CUT-OFF CURRENT CASE TEMPERATURE ES - Collector Cut-off Current - µa A CE = 1000 CE = 850 TCP762AC Base Current - A Case Temperature - C Figure 7. Figure 8. 5

6 , A MAXIMUM SAFE OPERATING REGIONS 100 MAXIMUM FORWARD-BIAS SAFE OPERATING AREA SAP762AA - Collector Current - A Z θjc / R θjc - Normalised Transient Thermal Impedance = 100 µs = 1 ms = 10 ms 0 01 DC Operation A CE - Collector-Emitter oltage - Figure 9. THERMAL THERMAL RESPONSE JUNCTION TO CASE POWER PULSE DURATION % 20% 5% 2% 1% 0% duty cycle = t1/t2 Read time at end of t1, T J(max) - = P D(peak) t 1 - Power Pulse Duration -s Figure 10. Z θjc R θjc t1 t2 ( ) TCP762AD R θjc(max) 6