INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2014 CR-V Publications No. AII Issue Date JULY 2013 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A Accessory User s Information Manual Transmitter Quick Start Guide Control unit Remote Control Engine Starter Attachment Kit P/N 08E92-T0A-100A Control unit bracket Antenna Engine starter harness Key ring Protective tape 3 Relays Fuse label 8 mm Nut Caution label 20 Wire ties 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 08E92-T0A-1A of 27

2 Long wire tie Illustration of the Remote Control Engine Starter on the Vehicle CONTROL UNIT 40A 7 Urethane tapes Template 3A 3 RELAYS Q0N2312AG Clip INSTALLATION TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Diagonal cutters Ratchet 8 mm, 10 mm, and 12 mm Sockets Combination wrench Isopropyl alcohol Scissors Small flat-tip screwdriver Shop towel Ruler Tape measure HDS (Honda Diagnostic System) Needle nose pliers Masking tape Electrical tape The following tool is available through the Honda Tool and Equipment Program. On the in click on: Service > Service Bay > Tool and Equipment Program, the enter the number under search. Or call Trim Tool Set (T/N SOJATP2014) Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: This antenna should only be installed if the ambient air temperature 15 C (60 F) or above. 1. Move the driver s seat all the way back. 2. Disconnect the negative cable from the battery. 2 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

3 Setting the Control Unit 3. Using a small flat-tip screwdriver, set the switches on the (accessory) control unit to the locations shown. NOTE: The switches must be set before the control unit is plugged in. If the switch settings are not correct, the remote engine starter will not operate correctly. If setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized. 4. Using isopropyl alcohol on a shop towel, clean the control unit where the protective tape will attach. Remove the adhesive backing, and attach the protective tape to the control unit over the switches. CONTROL UNIT SMALL FLAT-TIP SCREWDRIVER CONTROL UNIT SWITCHES SWITCHES Discharge any static electricity. SET PROTECTIVE SWITCHES TAPE ADHESIVE BACKING Remove. Clean with isopropyl alcohol AS Removing the Vehicle Parts 5. Remove the roof console. Using a plastic trim tool, pry out and remove the left and right lens (four retaining tabs each). Open the sunglass holder and remove the four screws. Remove the roof console (unplug the vehicle connectors). S SW:1 RR Junction unit > OFF SW:2 Trunk or Tailgate > ON SW:3 Smart Entry > OFF SW:4 Horn or Buzzer Answerback > OFF SW:5 Trunk Main SW > OFF SW:6 Reserve > OFF SUNGLASS HOLDER Open. 4 SCREWS ROOF CONSOLE RIGHT LENS AD LEFT LENS 4 RETAINING TABS 4 RETAINING TABS Q0N2012AG 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 3 of 27

4 6. Release the driver s sunvisor and passenger s sunvisor from the two sunvisor holders. 2 SUNVISOR HOLDERS 9. To prevent the clips from falling into the vehicle body, roll up the shop towel, and insert it between the driver s A-pillar and the dashboard. Take care not to damage the driver s A-pillar. DRIVER S A-PILLAR Rotate. DASHBOARD SUNVISOR HOLDER SUNVISOR HOLDER SUNVISOR Q0N2013AG 7. Rotate each sunvisor holders 45 counterclockwise to remove the two sunvisor holders. 8. Pull away the driver s door opening seal from the driver s A-pillar. Gently pull out the driver s A-pillar trim to release the clips. CLIP SHOP TOWEL Q0N2015BG 10. Remove the driver s A-pillar trim. Carefully remove the shop towel and any clips that fell from the driver s A-pillar trim. NOTE: The upper clip will stay in the body. DRIVER S A-PILLAR TRIM Remove. UPPER CLIP PANEL CLIP DRIVER S A-PILLAR TRIM DRIVER S A-PILLAR TRIM DRIVER S DOOR OPENING SEAL Pull away. DRIVER S A-PILLAR 2 CLIPS Q0N2014AG Q0N2016AG 4 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

5 11. Remove the remaining upper clip from the driver s A-pillar. 13. Remove the driver s dashboard panel (six clips and unplug the vehicle connector). Push 2 tabs. UPPER CLIP Discard. DRIVER S A-PILLAR DRIVER S DASHBOARD PANEL Q0N2017AG 6 CLIPS Q0N2019BG 12. Temporarily reinstall the driver s A-pillar trim, and check the overlap between the headliner and the driver s A-pillar trim according to the service manual. Remove the driver s A-pillar trim. Install the new clip (supplied) to the driver s A-pillar trim. 14. Remove the driver s air outlet (one self-tapping screw, one retaining tab, and three clips). DRIVER S AIR OUTLET 2 CLIPS NEW CLIP DRIVER S A-PILLAR TRIM (inside) RETAINING TAB SELF-TAPPING SCREW CLIP Q0N2020BG Q0N2018AG 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 5 of 27

6 15. Remove the driver s dashboard under cover (turn the knob, one clip and one pin). 17. Attach the masking tape to the upper column cover as shown. UPPER COLUMN COVER KNOB Turn. CLIP DRIVER S DASHBOARD UNDER COVER PIN Q0N2021BG MASKING TAPE STEERING WHEEL Q0N2023AG 16. Remove the driver s dashboard lower cover (eight clips and unplug the vehicle connector). 18. Lower the tilt lever, and turn the steering wheel 90 counterclockwise. STEERING WHEEL UPPER COLUMN COVER 8 CLIPS DRIVER S DASHBOARD LOWER COVER Q0N2022AG LOCK PLASTIC TRIM TOOL Q0N2024BG 19. Using a plastic trim tool, release the lock as shown. 6 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

7 20. Turn the steering wheel 180 clockwise. Using a plastic trim tool, release the lock as shown. 22. Remove the two self-tapping screws from the lower column cover. UPPER COLUMN COVER LOCK LOWER COLUMN COVER SELF-TAPPING SCREWS Q0N2027AG PLASTIC TRIM TOOL Q0N2025BG 23. Remove the lower column cover (one self-tapping screw). 21. Secure the upper column cover to the meter panel with the tape. METER PANEL 2 RETAINING TABS TAPE LOWER COLUMN COVER SELF-TAPPING SCREW Q0N2028AG UPPER COLUMN COVER Q0N2026AG 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 7 of 27

8 24. Remove the driver s front door sill trim (two retaining tabs, three clips, and two hooks). 2 RETAINING TABS DRIVER S FRONT DOOR SILL TRIM Installing the Antenna 26. Using the two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing as shown. 3 CLIPS FRONT PLATE 9 mm (0.3 in.) 2 HOOKS Q0N2029BG 15 mm (0.6 in.) 25. Pull away the driver s door opening seal, and remove the driver s kick panel (two clips). DRIVER S DOOR OPENING SEAL Pull away. NEEDLE NOSE PLIERS 2 CLIPS SCALE DRIVER S KICK PANEL Q0N2030AG PLATE Q0N1708CG 8 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

9 27. Using scissors, cut out the template. 29. Starting from the antenna end of the antenna cable, wrap three urethane tapes to the antenna cable at the measurements shown. Cut out. CABLE 410 mm (16.1 in.) SCISSORS URETHANE TAPES TEMPLATE Q0N1701BG 28. Using the strips of masking tape, attach the template to the front windshield. Align the template with the black ceramic paint as shown. BLACK CERAMIC PAINT TEMPLATE CABLE 20 mm (0.8 in.) 20 mm (0.8 in.) Q0N1703AG 30. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the antenna will attach. HEADLINER FRONT WINDSHIELD Clean with isopropyl alcohol. MASKING TAPES FRONT WINDSHIELD TEMPLATE CORRECT PLATE TEMPLATE Align this end with the end of the black ceramic paint. Q0N1702CG ADHESIVE BACKING Remove. Q0N1704AG 31. Remove the adhesive backing from the antenna. Insert the antenna plate under the headliner, align the antenna with the template, and attach the antenna to the front windshield. Press the antenna firmly for 30 seconds. 32. Remove the template American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 9 of 27

10 33. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner. 36. Route the antenna cable down the driver s A-pillar along the vehicle harness. PANEL HEADLINER HEADLINER 6 WIRE TIES CABLE CABLE CABLE Q0N1705AG 34. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel, where the urethane tapes will attach. DRIVER S A-PILLAR Q0N1707AG 37. Secure the antenna cable to the vehicle harness with six wire ties. 38. Route the antenna cable down behind the dashboard. TOP VIEW PANEL Clean with isopropyl alcohol. FRONT STEERING HANGER BEAM CABLE 2 URETHANE TAPES URETHANE TAPE Cut in half. Q0N1706AG 35. Using scissors, cut one urethane tape in half. Secure the antenna cable to the vehicle panel with two cut pieces of urethane tape. Be careful not to crease the headliner. CABLE Q0N1709BG 10 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

11 Routing the Engine Starter Harness 39. Plug the three relays into the relay block on the engine starter harness. RELAY 43. Unplug the vehicle 28-pin connector. 28-PIN 40A LABEL 40A LABEL RELAYS 28-PIN BLOCK RELAY BLOCK 3A LABEL Q0N1801AG 40. Using isopropyl alcohol on a shop towel, thoroughly clean the relay block and fuse block where the 3A fuse label and 40A fuse labels will attach. 41. Attach the 3A fuse label and two 40A fuse labels to the relay block and fuse block on the engine starter harness. 42. Route the two 28-pin connectors of the engine starter harness upward as shown. Q0N1804CG 44. Route the engine starter harness 28-pin connectors as shown, and plug the engine starter harness 28-pin connector into the vehicle 28-pin connector. 45. Push the engine starter harness 28-pin connector between the driver s A-pillar and vehicle 28-pin connector as shown. 28-PIN 28-PIN 28-PIN STEERING HANGER BEAM DRIVER S A-PILLAR 28-PIN TOP VIEW FRONT 28-PIN Q0N1805BG Q0N1802BG 46. Plug the vehicle 28-pin connector into the engine starter harness 28-pin connector American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 11 of 27

12 47. Secure the engine starter harness and the antenna cable to the vehicle frame with one wire tie. CABLE 49. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector. FRONT VIEW WIRE TIE FRAME 5-PIN Plug in here. WIRE TIE 5-PIN CABLE Q0N1806BG 2 1 Push. 2 Pull. Push. 48. Secure the engine starter harness and the antenna cable to the vehicle harness with one wire tie. UNLOCK 3 LOCK 1 Q0N1807BG 50. Plug the remaining engine starter harness 5-pin connector into the fuse box. NOTE: Check that the engine starter harness 5-pin connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall. 12 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

13 51. Attach the connector clip from the engine starter harness 5-pin connector to the hole in the vehicle panel. PANEL 5-PIN If the vehicle is equipped with the accessory fog lights, go to step 54; otherwise, continue with step Plug the engine starter harness 4-pin connector into the fuse box. Go to step 56. FRONT VIEW Plug in here. HOLE 4-PIN CLIP Q0N1901BG 52. Slide the other clip on the engine starter harness onto the vehicle connector. Note the direction and the orientation of the clip. FRONT Q0N1903BG CLIP Q0N1902BG 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 13 of 27

14 54. Unplug the fog light 4-pin connector from the fuse box, and plug it into the engine starter harness 4-pin connector. FRONT VIEW 56. Unplug the vehicle 38-pin connector from the fuse box as shown. COVER Plug in here. 4-PIN 38-PIN 38-PIN FRONT VIEW Q0N1905AG 57. Remove the connector cover. 58. Remove the lever from the vehicle 38-pin connector as shown. 2 TABS 4-PIN FOG LIGHTS 4-PIN Q0N1904BG 55. Plug the remaining engine starter harness 4-pin connector into the fuse box. LEVER Remove. 8-PIN 38-PIN SIDE VIEW 38-PIN 8-PIN QA21701AG 59. Remove the 8-pin connector from the vehicle 38-pin connector (two tabs). 14 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

15 60. Release the retainer from the 8-pin connector. SIDE VIEW ORANGE WIRE 65. Unplug the vehicle 24-pin connector, and plug the engine starter harness 24-pin connector into the vehicle 24-pin connector. FRONT VIEW TERMINAL RETAINER 24-PIN 8-PIN ORANGE WIRE Q0D1604AK 61. Insert the engine starter harness terminal (orange wire) into the 8-pin connector. Reinstall the 8-pin connector and lever. 62. Secure the engine starter harness to the vehicle harness with an electrical tape. 24-PIN 24-PIN Q0N2001BG ELECTRICAL TAPE Q0N1907AG 63. Reinstall the connector cover. 64. Plug the vehicle 38-pin connector into the fuse box American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 15 of 27

16 66. Slide the clip from the engine starter harness 24-pin connector onto the bottom of the fuse box, then plug the remaining vehicle 24-pin connector into the engine starter harness 24-pin connector. 67. Secure the engine starter harness to the vehicle harness with two wire ties. FRONT VIEW 24-PIN WIRE TIES Q0N2003BG 68. Route the engine starter harness under the dashboard and toward the steering wheel. FRONT LEFT KNEE BOLSTER FRONT CLIP 24-PIN HOLE 24-PIN Q0N2002BG Q0N2004AG 69. Secure the engine starter harness to the hole in the left knee bolster using the clip on the engine starter harness as shown. 16 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

17 70. Locate the white tape on the engine starter harness, and loosely secure the engine starter harness to the dashboard with one wire tie at the white tape. 73. Unplug the vehicle 7-pin connector from the ignition switch, and plug it into the engine starter harness 7-pin connector (black). WIRE TIE Loosely secure. STEERING WHEEL 7-PIN (Black) DASHBOARD WHITE TAPE Q0N2005AG IGNITION SWITCH 71. Route the engine starter harness up steering wheel as shown. 7-PIN 7-PIN (Black) Q0N2007AG 74. Plug the remaining engine starter harness 7-pin connector (black) into the ignition switch. 75. Secure the 7-pin connectors and engine starter harness to the vehicle harness with one wire tie. 2 WIRE TIES FRONT VIEWED FROM BOTTOM CLIP WHITE TAPE Q0N2006BG 72. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with two wire ties as shown. 7-PIN S WIRE TIE Q090211BK 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 17 of 27

18 76. Route the engine starter harness across the steering column area as shown. 79. Secure the 10-pin connectors and engine starter harness to the vehicle harness with one wire tie. STEERING WHEEL WIPER SWITCH IGNITION SWITCH WIRE TIE STEERING WHEEL 10-PIN 10-PIN S Q090302BK 10-PIN 10-PIN Q0N2008AG 77. Unplug the vehicle 10-pin connector from the wiper switch, and plug it into the engine starter harness 10-pin connector. 78. Plug the remaining engine starter harness 10-pin connector into the wiper switch. 18 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

19 80. Unplug the vehicle 12-pin connector from the combination light switch, and plug it into the engine starter harness 12-pin connector. COMBINATION LIGHT SWITCH 82. Secure the engine starter harness to the vehicle harness with two wire ties. Check that the harness is secured without undue strain to the both left and right connector cords. NOTE: Make sure that the connectors and harness are not pinched, or interfering with the steering wheel when adjusted. STEERING WHEEL LEFT CORD (without undue strain) WIRE TIES 12-PIN 12-PIN 12-PIN QA20704BG 81. Plug the remaining engine starter harness 12-pin connector into the combination light switch. RIGHT CORD (without undue strain) Q0N2010BG 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 19 of 27

20 83. Route the antenna cable along the engine starter harness as shown. FRONT WIRE TIE Installing the Control Unit 86. Using isopropyl alcohol on a shop towel, clean the area where the urethane tape will attach. CABLE URETHANE TAPE CABLE WIRE TIE LEFT KNEE BOLSTER WIRE TIE UNIT Clean with isopropyl alcohol. Q0N2305AG DASHBOARD Q0N2303AG 87. Attach the one urethane tape to the vehicle unit as shown. 88. Plug the antenna cable and the engine starter harness 28-pin connector into the control unit. 84. Secure the antenna cable to the engine starter harness with two wire ties. 85. Loosely secure the antenna cable to the dashboard with one wire tie loosely installed in step 70. CONTROL UNIT CABLE 28-PIN Q0N2306AG 20 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

21 89. Install the control unit bracket to the control unit. CONTROL UNIT BRACKET 91. Remove the vehicle flange nut that secures the vehicle bracket. CONTROL UNIT BRACKET CONTROL UNIT 8 mm NUT Q0N2307BG BRACKET FLANGE NUT (reused) CONTROL UNIT BRACKET 90. Secure the clip from the engine starter harness fuse block, and the clip from the engine starter harness into the holes in the control unit bracket. CONTROL UNIT BRACKET HOLE HOLE CLIP BLOCK Align. CONTROL UNIT BRACKET PANEL 8 mm NUT FLANGE NUT BRACKET Q0N2309AG 92. Install the control unit bracket on top of the vehicle bracket and align the control unit bracket with the edge of the vehicle bracket. Reinstall the vehicle flange nut. Install the 8 mm nut (supplied) on top of the vehicle flange nut. CLIP Q0N2308BG 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 21 of 27

22 93. Secure the antenna cable and engine starter harness to the vehicle harness with one long wire tie. 96. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tapes will attach. URETHANE TAPES Clean with isopropyl alcohol. WIRE TIE CABLE LONG WIRE TIE FRONT Q0N2310BG 94. Secure the antenna cable to the engine starter harness with one wire tie. 95. Bundle up the excess antenna cable, and secure it to the dashboard with the one wire tie loosely installed in step 85. LOWER COLUMN COVER (inside) Q090601AK 97. Attach the two urethane tapes to the inside of the lower column cover. 98. Open the hood. Using isopropyl alcohol on a shop towel, thoroughly clean the hood where the caution label will attach. CAUTION LABEL HOOD Clean with isopropyl alcohol. CABLE Bundle up the excess. ADHESIVE BACKING Remove. Q0N2011AG 99. Remove the adhesive backing from the caution label, and attach the caution label to the hood in the area shown. DASHBOARD WIRE TIE Q0N2311BG 22 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

23 100. Check that all wire harness and cables are routed properly and that all connectors are plugged in Reinstall all removed parts Reconnect the negative cable to the battery Check the operation of the headlights and wipers Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions Reset the clock on vehicles without navigation Proceed to the REMOTE REGISTRATION (Page 23) and FUNCTION CHECK (Page 26). REMOTE REGISTRATION 1. Acquire the PCM Code from ISIS. CAR ICON AH 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the on (II) position. 3. Start the HDS, and click the car icon. 4. Input the VIN and other required information into the HDS, then click the check button. Input the VIN and other required information. CHECK BUTTON AS 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 23 of 27

24 5. Select Honda Systems, then click the check button. 7. Check that REMARKS is shown, then click the check button. Check that REMARKS is shown. Select Honda Systems. CHECK BUTTON AS CHECK BUTTON AS 6. Select R/C ENG and click the check button. 8. Select REGISTER REMOTE CONTROL UNIT, then click the check button. Select R/C ENG. CHECK BUTTON AS Select REGISTER REMOTE CONTROL UNIT. CHECK BUTTON AS 24 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

25 9. The following message will display: Obtain PCM code (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password (USA). Click on the check button. 11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button. Obtain PCM-code message. The registration of the Remote Control Engine Starter Unit has been completed. CHECK BUTTON AS CHECK BUTTON AS 10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same. 12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button. Check that the engine can be started by the Transmitter. Input the PCM Code. CHECK BUTTON AS CHECK BUTTON 13. Perform the function test on page 26, then disconnect the HDS AS 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 25 of 27

26 FUNCTION CHECK Operating Conditions The hood is closed The shift lever is in park The key is out of the ignition and the key is outside the vehicle All doors and tailgate closed and locked Inspection 1. Press the command button, and then, within 1 second, press the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No: Make sure all Operating Conditions are met. Check the engine starter harness connections. Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2. Press the command button on the transmitter and, within 1 second, press the stop button. The engine should stop. Does the engine stop? Yes - Operation is normal. No - Check the engine starter harness connections. 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the driver s door must be opened and closed. Move the shift lever out of the P position. Unlock or open the doors or the tailgate. Open the hood. Insert the key in the ignition. Press on the brake pedal. Does the engine stop after each of these tests? STOP BUTTON TRANSMITTER DISPLAY COMMAND BUTTON START BUTTON AY Yes - Operation is normal. No - Check the engine starter harness connections. 4. Check that the power windows and the moonroof do not function when the engine is started with the transmitter. 5. Start the engine again, press the command button on the transmitter two times and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight. 7. Insert the key in the ignition and start the engine, check the operation of the headlights and wipers. 26 of 27 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

27 How to Program an Additional Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle s VIN and other required information. 4. Select Honda Systems. 5. Select R/C ENG. 6. Select REGISTER NEW TRANSMITTER. 7. When Ready to program the new transmitter shows, select ENTER. 8. Press and release the Command button. 9. Press and release the Stop button. 10. Perform the function check on both transmitters. NOTE: Only 2 remotes can be stored in the system s memory American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 27 of 27