LOOP 6 DRAWER DRESSER

Transcription

1 HRDWRE 24 - cams 24 - cam 12 - silver 13 - black 17 - wood dowels 24 - cam covers 24 - glide 6 - pulls Thank you for purchasing the Loop 6 Drawer Dresser. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. s you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. NOTE: 2 people are required to safely assemble this product. Missing hardware? Please call for replacements. TOOLS REQUIRED Phillips Head Screwdriver COMPONENTS 1 - top 1 - crossbar 1 - back LEFT RIGHT 6 - drawer backs 6 - drawer fronts (3 labeled LEFT, 3 labeled RIGHT on back of drawer fronts) 2 - side frames (1 left, 1 right) drawer sides (6 right, 6 left) 6 - drawer bottoms Page 1 of 5

2 rrow on each cam points towards edge with holes C ack Panel 1 ) Place left side face down on a padded surface. Insert 4 cam into the holes as shown. Secure, but do not over tighten with a phillips head screwdriver. ) Insert 3 cams into the large holes as shown, making sure the arrow on each cam points towards the nearest edge with holes. C) Insert 2 wood dowels into the top edge of the. Repeat Steps, & C for the right side. Crossbar 2 ) Insert 6 wood dowels, 3 cam, and 10 cams into back as shown. ) Insert 2 wood dowels and 2 cams into crossbar as shown. back 3 Insert 5 wood dowels and 6 cams into as shown. 4 Fit cam of back into corresponding holes in the. Page 2 of 5

3 crossbar 5 Secure 3 cams at the base of the with a Turn each cam clockwise until it securely engages each cam screw. 6 Carefully turn the and back assembly on end as shown. Fit dowel of into corresponding hole of crossbar. Secure crossbar with 1 black screw as shown, using a right side left side 7 Fit cam of right side into corresponding holes of back and crossbar. Secure cams with a 8 Fit cam of left side into corresponding holes of back and crossbar. Secure cams with a Page 3 of 5

4 top top 9 Insert 13 cam into the underside of the top as shown. 10 With assistance of another adult, position assembled unit upright. Fit cam of top into corresponding holes of assembled unit as shown. Secure all cams with a 11 Slide left and right drawer sides up into slots on back of the drawer front. Make sure glide hardware is on the outside of the drawer sides and the vertical slots are at the back of the assembly as shown. 12 Slide drawer back into vertical slots at rear of drawer sides. Page 4 of 5

5 These holes at back 12 Slide drawer bottom into slot at base of drawer sides and drawer front. Make sure pilot holes are at the back of the drawer bottom as shown. 13 ) Secure underside of drawer bottom to drawer back with 2 black. Secure, but do not over tighten with the phillips head screwdriver. ) Fit drawer pull into position as shown and secure with 2 silver. Repeat Steps 8-11 for remaining 5 drawers. 14 ) Fully extend drawer glides from assembled unit as shown. ) Position drawer assembly and rest the drawer assembly on top of the tabs as shown. ttach each glide to drawer with 2 glide as shown. Secure with a screwdriver. Repeat steps for each drawer. C) Conceal all exposed cams with cam covers. ssembly is now complete. NOTE: Drawers labeled LEFT on the back of drawer front are to be placed into the left side of the assembly. Drawers labeled RIGHT are to be placed into the right side of the assembly. CLENING ND CRE Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer. C Page 5 of 5