ELECTRON PRODUCTS ENVIRONMENTAL DATA METALLIZED PAPER AND OR PLASTIC FILM CAPACITORS ENGINEERING DATA SHEET SERIES
|
|
|
- Gwen O’Connor’
- 7 years ago
- Views:
Transcription
1 ELECTRON PRODUCTS INC. AND OR ENGINEERING DATA SHEET SERIES W ENVIRONMENTAL DATA APPLICATIONS Series W Metallized Paper and or Plastic Film Capacitors are non-polar, non-inductive wound capacitors. Series W Capacitors come in several styles: Oval Wrap & Fill (W Style); Round Wrap & Fill (WC Style); Axial Epoxy Case (WE Style); Radial Epoxy Case (W2E Style); Rectangular Hermetically Sealed (WG Style); Round Hermetically Sealed (WL Style). They are available in the Regular Size, as well as custom sizes to meet specific customer requirements. Contact our Engineering Department for special sizes, configurations, capacitance values and AC applications with Anti-Corona construction at all frequencies. Custom metal enclosures are available. Custom designed Feed Through capacitors (WQ Style) are also available for filter applications to specific requirements. OPERATING TEMPERATURE RANGE Range: -55 C to +85 C, without voltage derating. LIFE TEST Series W capacitors shall be capable of withstanding a test of 1000 hours at 85 C and 100% of the DC rated voltage or a test of 250 hours at 85 C and 140% of the DC voltage. The voltage shall be applied to each capacitor through its individual current-limiting resistor as determined from the formula R = 0.025/C, where C is the nominal capacitance in farads and R is in ohms. The test procedures shall be in accordance with MIL-C , except as noted herein. Not more than one failure in twelve shall be permitted. Any one of the following shall be considered a failure. a. A change in capacitance of more than 10% from it s initial value. b. An increase in Dissipation Factor to a value greater than 125% of the acceptance limit. c. A decrease in Insulation Resistance to a value less than 30% of the acceptance limit for 25 C. d. A permanent short or open. VIBRATION Series W capacitors shall be capable of withstanding a vibration test in accordance with MIL-STD-202, Method 201. The following details and exceptions shall apply: a. Mounting. The capacitor body shall be rigidly mounted by the entire body length to the vibration test fixture. The leads shall be soldered to rigidly supported terminals and so spaced that the length of each lead from the capacitor is 1/2 ± 1/8 inch from the edge of the supporting terminal. b. Measurement during Vibration. During the last cycle in each direction, an electrical measurement shall be made to detect intermittent contacts (not to be confused with "self healing" clearings) or open or short circuiting. c. Examination After Vibration. Capacitors shall be visibly examined for evidence of mechanical damage. MOISTURE RESISTANCE Series W capacitor Styles WG and WL (hermetically sealed in metal containers) shall be capable of withstanding the moisture resistance, humidity, and temperature and immersion cycling or MIL-C Styles WE and W2E (epoxy encased) and Style W (wrap & fill) capacitors are not intended for exposure to high humidity conditions over extended periods of time. TERMINAL STRENGTH Series W capacitors utilize tin-plated, copper-clad steel wire terminals which shall be capable of withstanding the following test without mechanical damage to the capacitor or terminals: a. Pull Test. The capacitor shall withstand a steady pull of 5 pounds axially to the leads for 1 minute. b. Bend Test. The wire lead terminals shall be bent at a point of 1/4 inch from the body of the capacitor, first 90 degrees in one direction, then back to the original position, and then 90 degrees in the opposite direction.
2 WRAP AND FILL, OVAL AXIAL LEAD W WRAP & FILL, OVAL DIMENSIONS See tables for specific T, W, L values. 1.5" Minimum T +.05" Maximum L ±.05" W +.05" Maximum (Length 1.5" Minimum) BODY LENGTH (L) AWG No. Diameter 0.65" " > 0.65" 1.00" " > 1.00" " wire axial leads; encased in skin-tight plastic wrap with epoxy end fill. Wrap & Fill capacitors are not intended for exposure to high humidity conditions over extended periods of time. For stringent environmental conditions, Wrap & Fill capacitors should be used in encapsulated or hermetically sealed circuitry. RATING T W L PART # T W L PART # T W L PART # T W L PART # +.05" +.05" ±.05" +.05" +.05" ±.05" +.05" +.05" ±.05" +.05" +.05" ±.05" W1-103E W2-103E W4-103E W6-103E W1-123E W2-123E W4-123E W6-123E W1-153E W2-153E W4-153E W6-153E W1-183E W2-183E W4-183E W6-183E W1-223E W2-223E W4-223E W6-223E W1-273E W2-273E W4-273E W6-273E W1-333E W2-333E W4-333E W6-333E W1-393E W2-393E W4-393E W6-393E W1-473E W2-473E W4-473E W6-473E W1-563E W2-563E W4-563E W6-563E W1-683E W2-683E W4-683E W6-683E W1-823E W2-823E W4-823E W6-823E W1-104E W2-104E W4-104E W6-104E W1-124E W2-124E W4-124E W6-124E W1-154E W2-154E W4-154E W6-154E W1-184E W2-184E W4-184E W6-184E W1-224E W2-224E W4-224E W6-224E W1-254E W2-254E W4-254E W6-254E W1-274E W2-274E W4-274E W6-274E W1-334E W2-334E W4-334E W6-334E W1-394E W2-394E W4-394E W6-394E W1-474E W2-474E W4-474E W6-474E W1-504E W2-504E W4-504E W6-504E W1-564E W2-564E W4-564E W6-564E W1-684E W2-684E W4-684E W6-684E W1-754E W2-754E W4-754E W6-754E W1-824E W2-824E W4-824E W6-824E W1-105E W2-105E W4-105E W6-105E W1-155E W2-155E W4-155E W6-155E W1-205E W2-205E W4-205E W6-205E W1-305E W2-305E W4-305E W6-305E W1-505E W2-505E W4-505E W6-505E W1-805E W2-805E W4-805E W6-805E W1-106E W2-106E W4-106E W6-106E
3 WRAP AND FILL, ROUND AXIAL LEAD WC WRAP & FILL, ROUND DIMENSIONS See tables for specific D, L values. 1.5" Minimum L ±.05" D +.05" Maximum (Length 1.5" Minimum) BODY LENGTH (L) AWG No. Diameter 0.71" " > 0.71" 1.25" " > 1.25" " wire axial leads; encased in skin-tight plastic wrap with epoxy end fill. Wrap & Fill capacitors are not intended for exposure to high humidity conditions over extended periods of time. For stringent environmental conditions, Wrap & Fill capacitors should be used in encapsulated or hermetically sealed circuitry. RATING D L PART # D L PART # D L PART # D L PART # +.05" ±.05" +.05" ±.05" +.05" ±.05" +.05" ±.05" WC1-103E WC2-103E WC4-103E WC6-103E WC1-123E WC2-123E WC4-123E WC6-123E WC1-153E WC2-153E WC4-153E WC6-153E WC1-183E WC2-183E WC4-183E WC6-183E WC1-223E WC2-223E WC4-223E WC6-223E WC1-273E WC2-273E WC4-273E WC6-273E WC1-333E WC2-333E WC4-333E WC6-333E WC1-393E WC2-393E WC4-393E WC6-393E WC1-473E WC2-473E WC4-473E WC6-473E WC1-563E WC2-563E WC4-563E WC6-563E WC1-683E WC2-683E WC4-683E WC6-683E WC1-823E WC2-823E WC4-823E WC6-823E WC1-104E WC2-104E WC4-104E WC6-104E WC1-124E WC2-124E WC4-124E WC6-124E WC1-154E WC2-154E WC4-154E WC6-154E WC1-184E WC2-184E WC4-184E WC6-184E WC1-224E WC2-224E WC4-224E WC6-224E WC1-254E WC2-254E WC4-254E WC6-254E WC1-274E WC2-274E WC4-274E WC6-274E WC1-334E WC2-334E WC4-334E WC6-334E WC1-394E WC2-394E WC4-394E WC6-394E WC1-474E WC2-474E WC4-474E WC6-474E WC1-504E WC2-504E WC4-504E WC6-504E WC1-564E WC2-564E WC4-564E WC6-564E WC1-684E WC2-684E WC4-684E WC6-684E WC1-754E WC2-754E WC4-754E WC6-754E WC1-824E WC2-824E WC4-824E WC6-824E WC1-105E WC2-105E WC4-105E WC6-105E WC1-155E WC2-155E WC4-155E WC6-155E WC1-205E WC2-205E WC4-205E WC6-205E WC1-305E WC2-305E WC4-305E WC6-305E WC1-505E WC2-505E WC4-505E WC6-505E WC1-805E WC2-805E WC4-805E WC6-805E WC1-106E WC2-106E WC4-106E WC6-106E
4 EPOXY CASE, AXIAL LEAD, RECTANGULAR WE EPOXY CASE, AXIAL, RECT. DIMENSIONS See tables for specific T, W, L values. 1.5" Minimum T +.01" Maximum L ±.03" W +.01" Maximum (Length 1.5" Minimum) BODY LENGTH (L) AWG No. Diameter 0.67" " > 0.67" 1.06" " > 1.06" " wire axial leads; encased in a molded epoxy/plastic shell with epoxy fill. Epoxy Case capacitors are not intended for exposure to high humidity conditions over extended periods of time. For stringent environmental conditions, Epoxy Case capacitors should be used in encapsulated or hermetically sealed circuitry. RATING T W L PART # T W L PART # T W L PART # T W L PART # +.01" +.01" ±.03" +.01" +.01" ±.03" +.01" +.01" ±.03" +.01" +.01" ±.03" WE1-103E WE2-103E WE4-103E WE6-103E WE1-123E WE2-123E WE4-123E WE6-123E WE1-153E WE2-153E WE4-153E WE6-153E WE1-183E WE2-183E WE4-183E WE6-183E WE1-223E WE2-223E WE4-223E WE6-223E WE1-273E WE2-273E WE4-273E WE6-273E WE1-333E WE2-333E WE4-333E WE6-333E WE1-393E WE2-393E WE4-393E WE6-393E WE1-473E WE2-473E WE4-473E WE6-473E WE1-563E WE2-563E WE4-563E WE6-563E WE1-683E WE2-683E WE4-683E WE6-683E WE1-823E WE2-823E WE4-823E WE6-823E WE1-104E WE2-104E WE4-104E WE6-104E WE1-124E WE2-124E WE4-124E WE6-124E WE1-154E WE2-154E WE4-154E WE6-154E WE1-184E WE2-184E WE4-184E WE6-184E WE1-224E WE2-224E WE4-224E WE6-224E WE1-254E WE2-254E WE4-254E WE6-254E WE1-274E WE2-274E WE4-274E WE6-274E WE1-334E WE2-334E WE4-334E WE6-334E WE1-394E WE2-394E WE4-394E WE6-394E WE1-474E WE2-474E WE4-474E WE6-474E WE1-504E WE2-504E WE4-504E WE6-504E WE1-564E WE2-564E WE4-564E WE6-564E WE1-684E WE2-684E WE4-684E WE6-684E WE1-754E WE2-754E WE4-754E WE6-754E WE1-824E WE2-824E WE4-824E WE6-824E WE1-105E WE2-105E WE4-105E WE6-105E WE1-155E WE2-155E WE1-205E WE2-205E WE1-305E WE2-305E WE1-505E WE1-805E
5 EPOXY CASE, RADIAL LEAD, RECTANGULAR W2E EPOXY CASE, RADIAL, RECT. DIMENSIONS See tables for specific T, H, L, S values. L ±.01" T ±.01" ** The mounting pads consist of two individual **.025" ±.010" S CENTER TO CENTER H ±.01" 1.0" Minimum pads on each end or one continuous pad on each end, depending on the mold. (Not an option). (Length 1.0" Minimum) LEAD SPACING (S) BODY LENGTH (L) (C to C ±.01") AWG No. Diameter.42".300" ".55".400" ".67".500" ".82".600" " 1.04".800" " 1.24" 1.100" " 1.75" 1.600" " wire radial leads; encased in a molded epoxy/plastic shell with epoxy fill. Epoxy Case capacitors are not intended for exposure to high humidity conditions over extended periods of time. For stringent environmental conditions, Epoxy Case capacitors should be used in encapsulated or hermetically sealed circuitry. RATING T H L PART # T H L PART # T H L PART # T H L PART # +.01" +.01" ±.01" +.01" +.01" ±.01" +.01" +.01" ±.01" +.01" +.01" ±.01" W2E1-103E W2E2-103E W2E4-103E W2E6-103E W2E1-123E W2E2-123E W2E4-123E W2E6-123E W2E1-153E W2E2-153E W2E4-153E W2E6-153E W2E1-183E W2E2-183E W2E4-183E W2E6-183E W2E1-223E W2E2-223E W2E4-223E W2E6-223E W2E1-273E W2E2-273E W2E4-273E W2E6-273E W2E1-333E W2E2-333E W2E4-333E W2E6-333E W2E1-393E W2E2-393E W2E4-393E W2E6-393E W2E1-473E W2E2-473E W2E4-473E W2E6-473E W2E1-563E W2E2-563E W2E4-563E W2E6-563E W2E1-683E W2E2-683E W2E4-683E W2E6-683E W2E1-823E W2E2-823E W2E4-823E W2E6-823E W2E1-104E W2E2-104E W2E4-104E W2E6-104E W2E1-124E W2E2-124E W2E4-124E W2E6-124E W2E1-154E W2E2-154E W2E4-154E W2E6-154E W2E1-184E W2E2-184E W2E4-184E W2E6-184E W2E1-224E W2E2-224E W2E4-224E W2E6-224E W2E1-254E W2E2-254E W2E4-254E W2E6-254E W2E1-274E W2E2-274E W2E4-274E W2E6-274E W2E1-334E W2E2-334E W2E4-334E W2E6-334E W2E1-394E W2E2-394E W2E4-394E W2E6-394E W2E1-474E W2E2-474E W2E4-474E W2E6-474E W2E1-504E W2E2-504E W2E4-504E W2E6-504E W2E1-564E W2E2-564E W2E4-564E W2E6-564E W2E1-684E W2E2-684E W2E4-684E W2E6-684E W2E1-754E W2E2-754E W2E4-754E W2E6-754E W2E1-824E W2E2-824E W2E4-824E W2E6-824E W2E1-105E W2E2-105E W2E4-105E W2E6-105E W2E1-155E W2E2-155E W2E1-205E W2E2-205E W2E1-305E W2E2-305E W2E1-505E W2E1-805E Note: Replace the last digit E with the desired tolerance code, from the tolerance table. For an in-between value use the next larger value s
6 HERMETICALLY SEALED, METAL CASED, RECTANGULAR WG HERMETIC SEAL, RECT. DIMENSIONS See tables for specific T, W, L values. 1.5" Minimum 3/32 T +.015" " L ±.031" W +.015" " (Length 1.5" Minimum) BODY SIZE (T) x (W) AWG No. Diameter.22" x.34" ".31" x.41" ".40" x.57" & Larger " wire axial leads; encased in a hermetically sealed rectangular tin plated brass tube with soldered glass to metal end seals. Metal encased capacitors are hermetically sealed and meet the moisture resistance, temperature and immersion cycling requirements of MIL-C RATING T W L PART # T W L PART # T W L PART # T W L PART # +.015" +.015" +.015" +.015" +.015" +.015" +.015" +.015" -.005" -.005" ±.031" -.005" -.005" ±.031" -.005" -.005" ±.031" -.005" -.005" ±.031" WG1-103E WG2-103E WG4-103E WG6-103E WG1-123E WG2-123E WG4-123E WG6-123E WG1-153E WG2-153E WG4-153E WG6-153E WG1-183E WG2-183E WG4-183E WG6-183E WG1-223E WG2-223E WG4-223E WG6-223E WG1-273E WG2-273E WG4-273E WG6-273E WG1-333E WG2-333E WG4-333E WG6-333E WG1-393E WG2-393E WG4-393E WG6-393E WG1-473E WG2-473E WG4-473E WG6-473E WG1-563E WG2-563E WG4-563E WG6-563E WG1-683E WG2-683E WG4-683E WG6-683E WG1-823E WG2-823E WG4-823E WG6-823E WG1-104E WG2-104E WG4-104E WG6-104E WG1-124E WG2-124E WG4-124E WG6-124E WG1-154E WG2-154E WG4-154E WG6-154E WG1-184E WG2-184E WG4-184E WG6-184E WG1-224E WG2-224E WG4-224E WG6-224E WG1-254E WG2-254E WG4-254E WG6-254E WG1-274E WG2-274E WG4-274E WG6-274E WG1-334E WG2-334E WG4-334E WG6-334E WG1-394E WG2-394E WG4-394E WG6-394E WG1-474E WG2-474E WG4-474E WG6-474E WG1-504E WG2-504E WG4-504E WG6-504E WG1-564E WG2-564E WG4-564E WG6-564E WG1-684E WG2-684E WG4-684E WG6-684E WG1-754E WG2-754E WG4-754E WG6-754E WG1-824E WG2-824E WG4-824E WG6-824E WG1-105E WG2-105E WG4-105E WG6-105E WG1-155E WG2-155E WG4-155E WG6-155E WG1-205E WG2-205E WG4-205E WG1-305E WG2-305E WG1-505E WG2-505E WG1-805E WG1-106E WG1-126E WG1-156E
7 HERMETICALLY SEALED, ROUND, METAL CASED. WL HERMETIC SEAL, ROUND DIMENSIONS See tables for specific D, L values. 1.5" Minimum.094" (Length 1.5" Minimum) BODY DIAMETER (D) AWG No. Diameter.175" &.195" ".235" &.312" " L ±.031" D +.015" ".400" & Larger " wire axial leads; encased in a hermetically sealed round tin plated brass tube with soldered glass to metal end seals. Metal encased capacitors are hermetically sealed and meet the moisture resistance, temperature and immersion cycling requirements of MIL-C RATING D L PART # D L PART # D L PART # D L PART # +.015" +.015" +.015" +.015" -.005" ±.031" -.005" ±.031" -.005" ±.031" -.005" ±.031" WL1-103E WL2-103E WL4-103E WL6-103E WL1-123E WL2-123E WL4-123E WL6-123E WL1-153E WL2-153E WL4-153E WL6-153E WL1-183E WL2-183E WL4-183E WL6-183E WL1-223E WL2-223E WL4-223E WL6-223E WL1-273E WL2-273E WL4-273E WL6-273E WL1-333E WL2-333E WL4-333E WL6-333E WL1-393E WL2-393E WL4-393E WL6-393E WL1-473E WL2-473E WL4-473E WL6-473E WL1-563E WL2-563E WL4-563E WL6-563E WL1-683E WL2-683E WL4-683E WL6-683E WL1-823E WL2-823E WL4-823E WL6-823E WL1-104E WL2-104E WL4-104E WL6-104E WL1-124E WL2-124E WL4-124E WL6-124E WL1-154E WL2-154E WL4-154E WL6-154E WL1-184E WL2-184E WL4-184E WL6-184E WL1-224E WL2-224E WL4-224E WL6-224E WL1-254E WL2-254E WL4-254E WL6-254E WL1-274E WL2-274E WL4-274E WL6-274E WL1-334E WL2-334E WL4-334E WL6-334E WL1-394E WL2-394E WL4-394E WL6-394E WL1-474E WL2-474E WL4-474E WL6-474E WL1-504E WL2-504E WL4-504E WL6-504E WL1-564E WL2-564E WL4-564E WL6-564E WL1-684E WL2-684E WL4-684E WL6-684E WL1-754E WL2-754E WL4-754E WL6-754E WL1-824E WL2-824E WL4-824E WL6-824E WL1-105E WL2-105E WL4-105E WL6-105E WL1-155E WL2-155E WL4-155E WL6-155E WL1-205E WL2-205E WL4-205E WL1-305E WL2-305E WL4-305E WL1-505E WL2-505E WL4-505E WL1-805E WL2-805E WL4-805E WL1-106E WL2-106E WL4-106E WL1-126E WL2-126E WL4-126E WL1-156E
8 PARAMETRIC TREND CURVES AND ACCEPTANCE CRITERIA W SERIES CAPACITANCE Reference MIL-STD-202, Method 305 Test Frequency: 1000 Hz Temperature: + 25 C Capacitance Change Over Temperature. Acceptance 55 C = -- 14% Maximum +85 C = ± 7% Maximum Change DISSIPATION FACTOR Reference MIL-STD-202, Method 306 Test Frequency: 1000 Hz Temperature: + 25 C Acceptance Limit: 1.2% Maximum INSULATION RESISTANCE Reference MIL-STD-202, Method 302 Electrification shall be at rated voltage or 500 VDC, whichever is less and for a time not greater than 2 minutes. Acceptance Limits: Test Megs x μf Megohms Temperature Minimum Need not C 250 C VOLTAGE RATING 100% of listed voltage rating from C to +85 C. VOLTAGE TEST Reference MIL-STD-202, Method 301. Surge current is limited to 1 ampere maximum. Voltage applied for 1 minute + 25 C. Ground test is performed terminal to case (where the case is not a terminal) at 200% of the DC voltage rating. Dielectric strength test is performed terminal to terminal at 150% of the DC voltage rating.
Types of Wound Film Capacitors
Types of Wound Film Capacitors A description of the various types of wound film capacitors available including construction, materials, features, strengths and application information. Prepared by Daryl
50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
SIL Resistor Network. Resistors. Electrical. Environmental. L Series. Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant
Resistors SIL Resistor Network Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2) Electrical Standard Resistance
SuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal
SuperTan Extended () Capacitors, Wet Tantalum Capacitors with Hermetic Seal FEATURES SuperTan Extended () represents a major breakthrough in wet tantalum capacitor Available technology. Its unique cathode
Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
AC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
AZ420 MINIATURE GENERAL PURPOSE RELAY
MINIATURE GENERAL PURPOSE RELAY FEATURES Rugged construction for high reliability Life expectancy greater than 0 million operations DC coils to 11 V Power consumption as low as 2 mw per pole available
TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
C ole s quality Open Frame Instrument Rotary Switch provides low
OPEN FRAME series C ole s quality Open Frame Instrument Rotary Switch provides low contact resistance (.005W), very high contact reliability, smooth action with positive positioning, precision design,
HIGH VOLTAGE TEMPERATURE COMPENSATED ZENER REFERENCE DIODES
Available HIGH VOLTAGE TEMPERATURE COMPENSATED ZENER REFERENCE DIODES DESCRIPTION The 1N4057 through 1N4085A series of temperature compensated reference diodes provides a wide selection of nominal voltages
RC NETWORKS SALES GUIDE
SALES GUIDE INTRODUCTION TO Recent developments in electronic equipment have shown the following trends: Increasing demands for numerical control machines, robotics and technically advanced appliances
Power Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
Pulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
Mylar polyester film. Electrical Properties. Product Information. Dielectric Strength. Electrode Size. Film Thickness
Product Information Mylar polyester film Electrical Properties Mylar offers unique design capabilities to the electrical industry due to the excellent balance of its electrical properties with its chemical,
STANDARD MICRO-D CONNECTORS
STANDARD MICRO-D CONNECTORS RECTANGULAR CONNECTORS Pigtail connector - Metal shell.............................. 56 Pigtail connector - Low profile - Metal shell.................... 58 Pigtail connector
Thick Film Resistor Networks, Dual-In-Line, Molded DIP
Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES Isolated, bussed, and dual terminator schematics available 0.160" (4.06 mm) maximum seated height and rugged, molded case construction Thick
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
SELECTION GUIDE. Nominal Input
www.murata-ps.com NKE Series FEATURES RoHS Compliant Sub-Miniature SIP & DIP Styles 3kVDC Isolation UL Recognised Wide Temperature performance at full 1 Watt load, 40 C to 85 C Increased Power Density
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC QUICK REFERENCE DATA DESCRIPTION VALUE Ceramic Class 1 2 Ceramic Dielectric U2J U2J Y5S, Y5U Y5S, Y5U Voltage (V AC ) 500 760
Application Guide Film Capacitors
Capacitance Change vs. Temperature Insulation Resistance vs. Temperature Polyester Typical Characteristics at 1 khz % Capacitance Change % Capacitance Change Polypropylene Typical Characteristics at 1
Operating Temperature Range: -30 to +85ç (Note 1) Operating Humidity Range: 40 to 80%
All non- products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative.
SECTION 13. Multipliers. Outline of Multiplier Design Process:
SECTION 13 Multipliers VMI manufactures many high voltage multipliers, most of which are custom designed for specific requirements. The following information provides general information and basic guidance
Life Expectancy : Class A Class B Class C Class D 30,000hrs 10,000hrs 3,000hrs 1000hrs
3.2 Motor Run Capacitors : continuous operation ypical Applications : Motor Run Capacitor ideal for various motor applications in washing machine, air conditioner, electric water pump, power factor collection
handbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing Extended voltage and capacitance range SMD-version, fully moulded, insulated Flexible terminals, reflow and wave solderable
High-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
3. ELECTRICAL PERFORMANCE PROPERTY TEST CONDITION PERFORMANCE 3. 1 Contact Resistance 1) Center Push 100mΩ Max
1. GENERAL 1. 1 Application : This specification is applied to MULTI WAY SWITCH for electronic equipment. 1. 2 Operating Temperature Range :-25 ~ 70 1. 3 Storage Temperature Range :-0 ~ 85. However, 96
SMA Interface Mating Dimensions (Per MIL-STD-348)
SMA Series SMA 6 SMA Interface Mating Dimensions (Per MIL-STD-348) SMA Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.250 6.35.263 6.68.. B.1790 4.55.1808
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type MKT80 FEATURES AEC-Q00 qualified (rev. D) for PCM. mm (for larger available components on request) High temperature capabilities, up to 0 C Capacitance up to 60
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/0805/1206/2512. RoHS compliant & Halogen free
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/005/1206/2512 RoHS compliant & Halogen free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE
Aluminum Capacitors Solid Axial
SAL-A End of Life. Last Available Purchase Date is -December- Radial higher CV/volume Fig. QUICK REFERENCE DATA DESCRIPTION VALUE Maximum case size (Ø D x L in mm) 6.7 x. to.9 x. Rated capacitance range
High-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to
CIN::APSE MICROMINIATURE D-SUB
INTRODUCTION CINCH has been producing filter connectors for years and has acquired an in depth knowledge of EMC protection. CINCH offers fast delivery on a wide range of standard filtered connectors and
Metallized Polypropylene Film Capacitors DC-Link Capacitor
Metallized Polypropylene Film Capacitors DC-Link Capacitor FEATURES Slim line, low building height Very long useful life time: Up to 100 000 h at U NDC and 70 C High ripple current capability, low ESR,
Type RP73 Series. SMD High Power Precision Resistors. Key Features. Applications. Characteristics - Electrical - RP73 Series - Standard
Key Features n High precision - tolerances down to 0.05% n Low TCR - down to 5ppm/ C n Stable high frequency performance n Operating temperature -55 C to +155 C n Increased power rating - up to 1.0W n
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
DATA SHEET CHIP RESISTORS RT Series 1%; 0.5%; 0.25%; 0.1%
DATA SHEET CHIP RESISTORS Series 1%; 0.5%; 0.25%; 0.1% Product specification Supersedes Date of Sep. 30, 2003 ynsc004 ynsc015 ynsc002 ynsc007 2 SCOPE This specification describes series chip resistors
Capacitance Cap. Tol. Suffix construction. Rated voltage
Metallized Polypropylene Film Capacitors Type:ECWFE Plastic Film Capacitors Non-inductive construction using metalized Polypropylene film with flame retardant plastic case. Features Small size Excellent
WIRE, TERMINAL AND CONNECTOR REPAIR CONDUCTORS
CONDUCTORS Conductors are needed to complete the path for electrical current to flow from the power source to the working devices and back to the power source. Special wiring is needed for battery cables
Wirewound Resistors, Industrial Power, Aluminum Housed, Chassis Mount
Wirewound Resistors, Industrial Power, Aluminum Housed, hassis Mount FEATURES Molded construction for total environmental protection omplete welded construction Meets applicable requirements of MIL-PRF-18546
How To Build A Low Voltage Capacitor Lvcp
Low Voltage Capacitor LVCP The new choice for Power Factor Correction LVCP : the new choice for Power Factor Correction The LVCP is a compact and powerful capacitor. It offers high modularity, unmatched
Interference Suppression Film Capacitors MKP Radial Potted Type
Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 7.5 mm to 27.5 mm lead pitch Supplied loose in box, taped on reel Material categorization: For definitions of compliance please
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
MLCC Voltage Strength
Frequently asked questions regarding: MLCC Strength Richard Tse TDK Corporation of America Abstract Industry practice and rules of thumb will vary when considering the proper voltage rating of a capacitor.
SUCCESS EPCOS Capacitors
SUCCESS EPCOS Inc. Capacitors Group April, 2012 EV / HV / E-Mobility Battery charger system & Inverter On Board and Off Board Assembly Trend: Wireless Charging DC/DC Converter Filtering DC Link E-Mobility
ATC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors
AC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors Features: Lowest ESR in Class Highest Working Voltage in class 250V Standard EIA Size: 0603 Laser Marking (Optional) RoHS Compliant High
Type MLS 125 C Flatpack, Ultra Long Life, Aluminum Electrolytic Now Available with High Vibration and High Reliability Options
Now Encased in rugged stainless steel, the MLS is perfect for high reliability military systems and applications operating above 85 C. For our highest performing 25 C Flatpacks, choose type HVMLS available
MADP-000504-10720T. Non Magnetic MELF PIN Diode
MADP-54-172T Features High Power Handling Low Loss / Low Distortion Leadless Low Inductance MELF Package Non-Magnetic Surface Mountable RoHS Compliant MSL 1 Package Style 172 Dot Denotes Cathode Description
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
Selector Switch Type 01
Selector Switch Type 0 Compact positions selector switch,000 switching cycles with up to.0 Ncm switching torque Gold plated contacts: micron Robust metal housing with metal shaft Optional IP front panel
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip
Selection Guide for Conversion of Carbon Composition Resistors
Selection Guide for Conversion of Carbon Composition Resistors believes that the information described in this publication is accurate and reliable, and much care has been taken in its preparation. However,
General Technical Information
Radio Interference Suppression Capacitors Introduction RADIO INTERFERENCE SUPPRESSION 1. Origin and Spreading of Interference: There are two main sources of radio interference: Devices, which due to their
Types MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
DISCONTINUED (1998) FBR46 SERIES. MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES RoHS compliant FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment.
High Ohmic/High Voltage Metal Glaze Leaded Resistors
VR37 High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 10 ASC_WR_V23 APR.- 2015
Application Note TMA Series
1W, SIP, Single & Dual Output DC/DC Converters Features SIP Package with Industry Standard Pinout Package Dimension: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 5V&12V Models 19.5 x 10.2 x 7.1 mm (0.77 x
Selector Switch Type 08
Compact and versatile 2 positions multi wafer selector switch For PCB mounting 25,000 switching cycles with up to 9.0 Ncm switching torque Gold plated contacts: micron Robust metal housing with metal shaft
CURRENT TRANSFORMER MODEL 546 UL1015 #16 AWG LEAD WIRE, STANDARD LENGTH IS 24" 1 X
CURRENT TRANSFORMER MODEL 546 1.10" I.D. PAGE No 1-38 REV 15DEC00 TERMINAL OPTION LEAD WIRE OPTION 1.10 0 1.20 2.55 3.00 3.47 0.18 x 0.31 SLOT ( 2 PLACES) 8-32 BRASS STUD (2 PLACES) UL1015 #16 AWG LEAD
Part Marking Instructions Chip Resistors
Chip Resistors Part Marking Instructions Part Marking Instructions Chip Resistors 1% Marking The nominal resistance is marked on the surface of the overcoating with the use of 4 digit markings. 0201 and
Section 21. Telecommunication Hardware. www.geindustrial.com BuyLog Catalog 21-1
Introduction...21-1 Fiber Closure Hardware...21-2 Cable Location Surge Protectors...21-4 Introduction GE has been manufacturing Telecommunication Hardware products for over 20 years and has become a leader
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT
HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT SERIES RF00 RF00D RF00DD RF0 RF0D RF0DD RELAY TYPE Repeatable, RF relay Repeatable, RF relay with internal diode for coil transient suppression Repeatable,
High Surge Axial Cemented Wirewound Resistors
High Surge Axial Cemented Wirewound Resistors FEATURES High voltage surge (up to 12 kv) withstanding capability Non flammable silicon cement coating High grade ceramic core Material categorization: for
2a. IEM Indoor Metal Clad Medium Voltage Switchgear 15KV 16346-1. 2a. Section 16346 INDOOR METAL CLAD MEDIUM VOLTAGE SWTICHGEAR (Std.
2a. IEM Indoor Metal Clad Medium Voltage Switchgear 15KV 16346-1 2a. Section 16346 INDOOR METAL CLAD MEDIUM VOLTAGE SWTICHGEAR (Std. Relays) Part 1 General 1.1 CONDITIONS AND REQUIREMENTS: A. Refer to
High Ohmic (up to 68 MΩ)/ High Voltage (up to 10 kv) Resistors
High Ohmic (up to 68 MΩ)/ A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps.
RT series Miniature Printed Circuit Board Relays, Sockets and Accessories
s RT series Miniature Printed Circuit oard Relays, Sockets and ccessories pplied Coil Voltage (% of rated nom.) RT series (DC Coil) 6 mp PC oard Miniature Relay Meets VDE 0mm Spacing, KV Dielectric File
Polymer Termination. Mechanical Cracking 2. The reason for polymer termination. What is Polymer Termination? 3
Polymer Termination An alternative termination material specifically designed to absorb greater levels of mechanical stress thereby reducing capacitor failures associated with mechanical cracking Mechanical
Metal Film Resistors, Military, MIL-R-10509 Qualified, Type RN and MIL-PRF-22684 Qualified, Type RL
CMF (Military RN and RL) Metal Film Resistors, Military, Qualified, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient
Precision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
SlimSeal SSL Connector. Now Available in 1 Position. Free Hanging Version
Now Available in 1 Position Free Hanging Version SlimSeal SSL Connector The SlimSeal SSL connectors are low profile, single row connectors developed for indoor and outdoor LED lighting applications. These
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC / Class Y1, 500 V AC
4L Series AC Line Rated Ceramic Disc Capacitors Class X, 76 V AC / Class Y, 5 V AC FEATURES Complies with IEC 6384-4, 4 th edition High reliability Radial leads High capacitance up to nf Singlelayer AC
DISCRETE SEMICONDUCTORS DATA SHEET. BLF244 VHF power MOS transistor
DISCRETE SEMICONDUCTORS DATA SHEET September 1992 FEATURES High power gain Low noise figure Easy power control Good thermal stability Withstands full load mismatch Gold metallization ensures excellent
Flexible Printed Circuits Design Guide
www.tech-etch.com/flex Flexible Printed Circuits Design Guide Multilayer SMT Assembly Selective Plating of Gold & Tin-Lead Fine Line Microvias Cantilevered & Windowed Leads 1 MATERIALS CONDUCTOR Copper
Capacitors in Circuits
apacitors in ircuits apacitors store energy in the electric field E field created by the stored charge In circuit apacitor may be absorbing energy Thus causes circuit current to be reduced Effectively
Gas Discharge Tubes GTCX26-XXXM-R05 Series
Raychem Circuit Protection 6mm 2Pole GDTs (ceramic gas discharge tubes), are commonly used to help protect sensitive telecom equipment such as communication lines, signal lines and data transmission lines
Whale 3. User Manual and Installation Guide. DC Servo drive. Contents. 1. Safety, policy and warranty. 1.1. Safety notes. 1.2. Policy. 1.3. Warranty.
Whale 3 DC Servo drive User Manual and Installation Guide Contents 1. Safety, policy and warranty. 1.1. Safety notes. 1.2. Policy. 1.3. Warranty. 2. Electric specifications. 2.1.Operation ranges. 3. Connections
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
Guide for Molded Tantalum Capacitors
Guide for Molded Tantalum Capacitors INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability,
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) Rotor. Wiper. Cover. Pin S T - 2 T A 1 0 0 Ω ( 1 0 1 )
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) COPAL ELECTRONICS RoHS compliant INTERNAL STRUCTURE 8 4 7! 5! 9 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7
SMA Connectors. RF Coax Connectors. Product Facts
SMA Connectors Product Facts Performance to 12.4 GHz and beyond Available in various base metal options, including stainless steel, brass and zinc diecast Uses industry standard crimp tools and processes
I-PEX MHF4 Micro Coaxial Connector
PRODUCT SPECIFICATION I-PEX MHF4 Micro Coaxial Connector Plug P/N 20448-001R-81 Receptacle P/N 20449-001E RF Connector, RF Cable & Antenna Manufacturer E-mail: sales@wellshow.com.tw Tel: +886-2-24239376
POWER AND VOLTAGE RATING
POWER AND VOLTAGE RATING SCOPE: The purpose of this document is to take the confusion out of power and voltage ratings in specifications and in product information publications. This will be accomplished
Gas Discharge Tubes GTCX36-XXXM-R05 Series
GTCX36-XXXM-R05 Series TE Circuit Protection 6mm 3Pole GDTs (ceramic gas discharge tubes), are commonly used to help protect sensitive telecom equipment such as communication lines, signal lines and data
ST-2 SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) FEATURES PART NUMBER DESIGNATION S T - 2 T A 1 0 0 Ω ( 1 0 1 ) RoHS compliant
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) ST- RoHS compliant INTERNAL STRUCTURE 8 4 7 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7 8 9!! 5 Part name Housing
High Voltage Power Supplies for Analytical Instrumentation
ABSTRACT High Voltage Power Supplies for Analytical Instrumentation by Cliff Scapellati Power supply requirements for Analytical Instrumentation are as varied as the applications themselves. Power supply
Measurement of Capacitance
Measurement of Capacitance Pre-Lab Questions Page Name: Class: Roster Number: Instructor:. A capacitor is used to store. 2. What is the SI unit for capacitance? 3. A capacitor basically consists of two
www.jameco.com 1-800-831-4242
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. SPECIFICATION CUSTOMER: JAMES DATE: 04.08.23 MODEL NO: DBU090030 DESIGNED
SUPERSEDED REVISION. Gas Discharge Tubes GTCX28-XXXM-R20 Series. Features: Benefits: Applications
GTCX28-XXXM-R20 Series Raychem Circuit Protection 8mm 2Pole GDTs (ceramic gas discharge tubes), are commonly used to help protect sensitive telecom equipment such as communication lines, signal lines and
SMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ MAGNETIC-LATCHING RF RELAY
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ MAGNETIC-LATCHING RF RELAY SERIES RF121 RELAY TYPE RF Magnetic-Latching, SPDT, Through-hole Relay DESCRIPTION The ultraminiature RF121 relay is built on Teledyne
General information. Please refer to our Internet address (http://www.kemet.com) for updated information on KEMET products, services and news.
DC Film Capacitors Please refer to our Internet address (http://www.kemet.com) for updated information on KEMET products, services and news. Contents Pitch Rated Voltage Capacitance Page mm Vdc range range
CMR Series Isolated 0.75W Single and Dual Output Isolated DC/DC Converters
www.murata-ps.com CMR Series SELECTION GUIDE FEATURES Single or Dual Isolated Outputs 1kVDC or 3kVDC options Wide temperature performance at full 0.75W load -40 C to 85C Industry Standard Pinouts 5V, 12V
DSD 70 Dual Channel Hall Effect Speed Sensor for Railway Applications, compliant with EN 50155
DSD 70 Dual Channel Hall Effect Speed Sensor for Railway Applications, compliant with EN 50155 Technical information Version: 07.14 General Function The speed sensors family DSD.70 are suitable for generating
EE301 Lesson 14 Reading: 10.1-10.4, 10.11-10.12, 11.1-11.4 and 11.11-11.13
CAPACITORS AND INDUCTORS Learning Objectives EE301 Lesson 14 a. Define capacitance and state its symbol and unit of measurement. b. Predict the capacitance of a parallel plate capacitor. c. Analyze how
CABLE SPECIFICATION CAN CAB RJ45-SUBD9
CABLE SPECIFICATION All technical information contained in this document is the exclusive property of STI and may neither be used nor disclosed without its prior written consent. AAV 33801 1/8 Connector