SPECIFICATION DIAGRAM Model IC 300 Deluxe IC 200 Executive IC 100 Standard

Transcription

1 Issue: E Description: ROBINHOOD IRONING CENTRE Model Number: IC300/200/100 SPECIFICATION DIAGRAM Model IC 300 Deluxe IC 200 Executive IC 100 Standard All dimensions in mm Model may vary slightly from images pictured Model pictured: IC300 1

2 Overview Contents of packaging: 1 x Robinhood Ironing Centre 1 x Installation kit (incl screws..) 1 x Door (incl handle) Pre-installation Important: o Please read the entire instructions before installing the Ironing Centre. o Robinhood Ironing Centre can be mounted in two ways: Recessed Mount and Surface Mount. For Surface Mount an additional decorative collar can be purchased (Product Code ICMC). o Remove the Packing Stops with the small flat screwdriver from the Ironing Board assembly (only on Deluxe). o Ascertain from the user the DESIRED HEIGHT of the Ironing Board when in the open position. o We recommend an ironing surface height of 830mm above the floor for an average adult. To obtain this surface height, the height of the unit (see diagram below) must be 680mm above the floor. o For Deluxe, 830mm is based on the second or middle position of the ironing board. 2

3 Mounting the Ironing Centre SURFACE MOUNT OPTION o Make sure sold timber studs or mounting points are in suitable position for the mounting of the ironing centre. o Drill through the back of the cabinet and fasten the six screws supplied (it may be necessary to purchase different length screws for correct fitting, or use wall anchors if unit is to be mounted to solid wall.) NOTE: Collar Kit Product Code ICMC) is also available. RECESS MOUNT OPTION 1. SIZE OF WALL OPENING The Ironing Centre is designed to fit between 362mm studs. Take out a section of the wall and insert two timber studs vertically at 362mm apart. 2. ATTACH BRACE Attach horizontal brace between the studs at the desired height. Ensure that the brace is level. 3. MOUNT CABINET Lift cabinet into place, rest the cabinet on horizontal brace, plumb and shim cabinet to fit, and attach to studs using the supplied screws. Mounting hole positions are indicated by the arrows. On the Electric models, remove the wireway cover to access mounting hole. Be sure to allow for wall covering thickness behind cabinet face frame. 3

4 Connecting the Ironing Centre to Electric Power o For recessed mount, an external ON/OFF (safety) switch for the Ironing Centre must be installed near the unit. An additional power socket can be installed inside the wall between the switch and power plug. o Alternatively the unit can be hard wired directly to the switch by an electrician. o For surface mount, the Ironing Centres plug and lead can be easily plugged into a nearby wall socket, or can be hard wired by an electrician. Door Assembly Instructions 1. Mounting the Cabinet Door o o o o Door may be hinged from either side of the cabinet (illustration is shown for right side hinging). Both sides of the cabinet have pre-punched holes. Use the two hinges supplied to fix door to the cabinet. Attach the hinges to door and cabinet using the screws supplied at the top and bottom section of the cabinet. Use the decorative plugs supplied to cover the unused pre-punched holes. 2. Fixing Magnetic Catch o Magnetic catch is fixed opposite to the hinge. o Fixing position is located on the top section of the cabinet and the door. o Attach the magnetic catch 2A onto cabinet using the screws supplied. o Attach the strike plate 2B onto door using the screw supplied. 4

5 Operating Instructions To open the Ironing Board, lift board retainer and lower the board. To store Ironing Board, follow the steps in reverse order. On DELUXE Model. The Ironing Board has three working heights, to adjust the board: 1. With the board in the horizontal position hold the board with one hand near the base (NOT BY THE NOSE) and support the pivot rod with the other hand. 2. Adjust the Ironing board to the desired position by lifting the board (NOT BY THE NOSE) and moving it to the path of height adjust bracket. NOTE: In order to store the Ironing board, it must be on its lowest position. Lamp Replacement 1. Disconnect Ironing Centre from power supply. Ensure the power is switched off. 2. Insert small screwdriver or slim knife as shown, ease catch to side and slip out diffuser. 3. Replace lamp (40 watt max.) 4. Slide diffuser back into aperture and click into place. Turn power back on. 5

6 Ironing Centre Features All Robinhood Ironing Centres have the following features: o Surface or recess mountable o Utility shelf for spray bottle storage o Heat resistant shelf for iron storage o Integrated cotton coated rayon cover o Right or left hand o Magnetic door catch opening door o Round corners board In addition to these standard features Executive Model IC 200 o Built in volt power outlet o 40 watt light o Auto timer Deluxe Model IC 300 o Built in volt power outlet o 40 watt light o Auto timer o 3 level height adjustable o Board Swivels a full 180. Model IC 300 shown Maintenance YOUR IRONING CENTRE BOARD IS NOW FITTED WITH A HEAT RESISTANT COVER. TO AVOID DAMAGE TO THE MATERIAL PLEASE DO NOT WASH THE COVER The laminated surface of the unit may be wiped clean with non abrasive household cleaner. WARNING 1. Do not place EXCESSIVE WEIGHT (weight should not exceed 15kg) on the Ironing Board when opened as it is designed to accept normal ironing use only. 2. Iron not to exceed 2000 Watt. 3. Allow iron to cool down before storing in the cabinet. 4. Empty water reservoir and turn off steam action prior to storing iron. 5. Turn power off when not in use. 6. Do not remove the board retainer. 7. The appliance is not intended for use by young children or infirm persons without supervision. 8. Young children shall be supervised to ensure that they do not play with the appliance. 9. The appliance is supplied with an approved power cable which must not be changed. If the supplied cord of this equipment is damaged, it must only be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid hazard. 10. Upon installation, ensure that the socket outlet (for Surface Mount) or ON/OFF switch (for RECESSED MOUNT) remains easily accessible after installation. 6

7 Warranty Certificate (New Zealand) The benefits conferred hereunder are in addition to all other rights and remedies in respect of the product which the purchaser has by virtue of the Consumer Guarantee Act and similar legislation, and nothing contained in this Certificate shall in any way limit the purchaser's rights under such legislation. Terms and Conditions The following conditions apply in respect of the warranty given in this certificate: 1. Robinhood warrants this product against manufacturing defects and faulty materials for a period of: 2. Rangehood 24 months from date of original purchase. 3. Supertub Lifetime on stainless bowl, 5 years on single lever unit, 1 year on other components from date of original purchase. 4. Ironing Centre 12 months from date of original purchase. 5. Uniduct 12 months from date of original purchase. For commercial use 3 months from date of original purchase. 6. This warranty is limited to the repair or replacement free of charge within the warranty period of any component part which Robinhood at its discretion determines to be faulty. Such warranty is subject to terms and conditions set out below. 7. The warranty applies within New Zealand. 8. The customer must produce the original invoice or other purchase documentation as proof of the purchase date. 9. To abide by the guarantee please complete the details below and keep it with your purchase invoices. 10. In the event that service is required, contact the source from whom the product was purchased. It will be the responsibility of that sales agent to direct the purchaser to an authorised service centre or replace the defective parts. All costs of labour performed outside an authorised Service Centre will not be the responsibility of Robinhood. Alternatively contact Robinhood. Warranty exclusions 1. The warranty does not apply for the following: If defect is caused by misuse, wear and tear, dirt, fire or accidental damage. If the product has been repaired or serviced by an unauthorised person. If installed contrary to Robinhood instructions. Products purchased overseas or not designed for use in New Zealand. Normal user adjustments or customer instruction on the product s operation. Abnormal product performance as a result of incorrect installation or deviation from specified instructions. All costs incurred on installation or removal. If the product is used outdoors. 2. A charge shall be made if the service person finds the product is functioning correctly. 3. Paint finishes and the colours in plastics are fully covered by this warranty for 12 months from date of purchase. Should service be required please contact the store where you purchased your Robinhood product. If you require any further advice or information on Robinhood product feel free to contact: Robinhood Free Phone: Free Fax: enquiries@robinhood.co.nz Website: Name of purchaser Address Date of purchase Model number Serial No/Date stamp Name of supplier Address Invoice number Complete these details and keep it with your purchase invoice. DO NOT POST 7

8 Warranty Certificate (Australia) The benefits conferred hereunder are in addition to all other rights and remedies in respect of the product which the purchaser has by virtue of the Trade Practices Act 1974 and similar State and Territory legislation and nothing contained in this Certificate shall in any way limit the purchaser's rights under such legislation. Terms and Conditions The following conditions apply in respect of the warranty given in this certificate: 1. Robinhood warrants this product against manufacturing defects and faulty materials for a period of: 2. Rangehood 24 months from date of original purchase. 3. Supertub Lifetime on stainless bowl, 5 years on single lever unit, 1 year on other components from date of original purchase. 4. Ironing Centre 12 months from date of original purchase. 5. Uniduct 12 months from date of original purchase. For commercial use 3 months from date of original purchase. 6. This warranty is limited to the repair or replacement free of charge within the warranty period of any component part which Robinhood at its discretion determines to be faulty. Such warranty is subject to terms and conditions set out below. 7. The warranty applies within the Commonwealth of Australia. 8. The customer must produce the original invoice or other purchase documentation as proof of the purchase date. 9. To abide by the guarantee please complete the details below and keep it with your purchase invoices. 10. In the event that service is required, contact the source from whom the product was purchased. It will be the responsibility of that sales agent to direct the purchaser to an authorised service centre or replace the defective parts. All costs of labour performed outside an authorised Service Centre will not be the responsibility of Robinhood. Alternatively contact Robinhood or your nearest Service Agent as listed below. Warranty exclusions 1. The warranty does not apply for the following: If defect is caused by misuse, wear and tear, dirt, fire or accidental damage. If the product has been repaired or serviced by an unauthorised person. If installed contrary to Robinhood instructions. Products purchased overseas or not designed for use in New Zealand. Normal user adjustments or customer instruction on the product s operation. Abnormal product performance as a result of incorrect installation or deviation from specified instructions. All costs incurred on installation or removal. If the product is used outdoors. 2. For warranty service outside of Capital City metropolitan area or 30 km from nearest authorised service agent the purchaser shall be liable for travelling expenses and cost of transport of the product or parts to and from the Service Agent 3. Paint finishes and the colours in plastics are fully covered by this warranty for 12 months from date of purchase. 4. A charge shall be made if the service person finds the product is functioning correctly. Should service be required please contact the store where you purchased your Robinhood product. If you require any further advice or information on Robinhood product feel free to contact: Robinhood Free Phone: Free Fax: enquiries@robinhood.com.au Website: Area Service agents Contact details Victoria J.A. Appliances Tel: (03) Fax: (03) jaappliances@statewideservices.com.au New South Wales (Sydney, North Coast) All General White Goods Services Tel: (02) Fax: (02) service@agw.com.au New South Wales (Country, Wagga Wagga) K J Wardens Tel: (02) Fax: (02) ACT K J Wardens Tel: (02) Fax: (02) Tasmania BSH Electrical Pty Ltd Tel: (03) Fax: (03) South Australia Ivesons Electrical Tel: (08) Fax: (08) Western Australia J.H. Wilberforce Tel: (08) Fax: (08) Queensland Terry Hayes Agencies Tel: Fax: (07) info@terryhayesagencies.com Name of purchaser Address Date of purchase Model number Serial No/Date stamp Name of supplier Address Invoice number Complete these details and keep it with your purchase invoice. DO NOT POST New Zealand Robinhood Ltd Telephone: Facsimile: enquiries@robinhood.co.nz Australia Robinhood PTY Ltd Telephone: Facsimile: enquiries@robinhood.com.au ECN: ECN: