INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Accessory NIGHT Application 2009 CR-V Publications No. AII Issue Date AUG 2008 PARTS LIST Automatic Day/Night Mirror Attachment Kit P/N 08V03-SWA-100 Harness cover set Automatic Day/Night Mirror Kit P/N 08V03-S9A-100B Day/Night mirror Automatic Day/Night mirror harness Operating Instructions 9 Wire ties 4 EPT sealers TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Isopropyl alcohol Shop towel Diagonal cutters T-20 and T-25 TORX bits Needle nose pliers Steel wire Clip Ground bolt 2008 American Honda Motor Co., Inc. All Rights Reserved AII (0808) 08V03-SWA of 8

2 Illustration of the Day/Night MIirror Installed on the Vehicle 3. Carefully remove the right and left map light lens from the roof console (four tabs for each lens). DAY/NIGHT ROOF CONSOLE 4 RETAINING TABS 4 RETAINING TABS B MAP LIGHT LENS RIGHT MAP LIGHT LENS Y INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down radio station presets. 2. Disconnect the negative cable from the battery. 4. Remove the roof console (four bolts and unplug the vehicle connectors). ROOF CONSOLE SILVER BOLTS BLACK BOLTS Y 2 of 8 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved

3 5. Remove the cover from the left sunvisor (four retaining tabs). 8. Remove the cover from the mirror (two retaining tabs). Lift up the mirror while pulling the base, and remove the mirror. 2 RETAINING TABS COVER 4 RETAINING TABS Lift up. BASE Pull. COVER SUNVISOR TORX SCREWS Remove the two T-25 TORX screws, pull out the left sun visor, and remove the sunvisor. 7. Remove the right and left sunvisor holders. Using a flat-tip screwdriver, push in on the tab and rotate the holder. BASE B SUNVISOR HOLDER 9. Using a flat-tip screwdriver, remove the two caps from the left front grab rail. FLAT-TIP SCREWDRIVER Push. FLAT-TIP SCREWDRIVER Turn. 2 SUNVISOR HOLDERS RIGHT SUNVISOR HOLDER Y 2 CAPS GRAB RAIL GRAB RAIL CAPS B 2008 American Honda Motor Co., Inc. All Rights Reserved AII (0808) 3 of 8

4 10. Using needle nose pliers, remove the left front grab rail (two clips). 12. Remove the left A-pillar trim (two clips). GRAB RAIL 2 S 2 S NEEDLE NOSE PLIERS DOOR OPENING SEAL GRAB RAIL B 11. Remove the front door opening seal around the A-pillar trim. Using a rubber mallet, strike the top of the A-pillar trim, in the area marked SIDE CURTAIN AIRBAG, to release the clip. Remove the clip. A-PILLAR TRIM 13. Remove the left front door sill trim (three clips). 3 S B RETAINING TAB Collapsed. Remains on the vehicle panel. RETAINING TAB Tap. BODY PIN Comes off from the clip. Pull. BODY Pushed deep behind the vehicle panel. BODY DOOR SILL TRIM DOOR OPENING SEAL PART MARKED AS SIDE CURTAIN AIRBAG B A-PILLAR TRIM Tap at right angles to the vehicle. Tap with a rubber mallet. 4 of 8 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved

5 14. Remove the front door opening seal from around the left kick panel. Remove the left kick panel (two clips). DOOR OPENING SEAL 2 S NOTE: If another accessory is already plugged into the 6- pin connector opening of the fuse box, remove the dummy connector from the 6-pin connector taped to the automatic day/night mirror harness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the automatic day/night mirror harness you just unplugged and plug the automatic day/night mirror harness into the 6-pin connector opening of the fuse box. 6-PIN OPENING of the OTHER ACCESSORY 6-PIN DUMMY KICK PANEL B 15. Plug the automatic day/night mirror harness 6-pin connector into the empty 6-pin connector opening of the fuse box. OPEN 6-PIN OPEN 6-PIN 6-PIN 16. Attach a piece of steel wire to the automatic day/ night mirror harness, and route it through the left front pillar trim opening. AUTOMATIC DAY/NIGHT PILLAR TRIM OPENING STEEL WIRE 6-PIN B NIGHT B 2008 American Honda Motor Co., Inc. All Rights Reserved AII (0808) 5 of 8

6 17. Route the automatic day/night mirror harness behind the fuse box. 19. Route the automatic day/night mirror harness above the headliner from the left A-pillar to the middle of the vehicle B 18. Remove the steel wire. Route the automatic day/ night mirror harness along the vehicle harness as shown. Loosely secure the day/night mirror harness to the vehicle harness with the four wire ties. HEADLINER A-PILLAR 7-PIN B 20. Plug the automatic day/night mirror into the day/night mirror 7-pin connector. 7-PIN BASE A- PILLAR WIRE TIE PILLAR TRIM OPENING B TORX SCREW Up B 21. Install the day/night mirror on the mirror base, then tighten the T-20 TORX screw installed in the day/night mirror. 6 of 8 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved

7 22. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the EPT sealer will attach. Secure the automatic day/night mirror harness to the headliner with three EPT sealers. 25. Remove the vehicle bolt from the fuel lid opener. Attach the automatic day/night mirror harness ground terminal with the ground bolt supplied. EPT SEALERS GROUND BOLT BOLT (Not used) HEADLINER FUEL LID OPENER AUTOMATIC DAY/NIGHT B 23. Pull the slack in the automatic day/night mirror harness down the A-pillar to the fuse box. Tighten the four wire ties installed in step Secure the automatic day/night mirror harness to the vehicle harness with the two wire ties in the areas shown. 26. Install the harness cover to the automatic day/night mirror and the headliner. NIGHT HAR- NESS GROUND TERMINAL HEADLINER B COVER WIRE TIE B WIRE TIE B 2008 American Honda Motor Co., Inc. All Rights Reserved AII (0808) 7 of 8

8 27. Remove and discard the upper vehicle clip from the left A-pillar. A-PILLAR Remove. 30. Check that all wire harnesses are routed properly and all connectors are plugged in. 31. Reinstall all removed parts. 32. Reconnect the negative cable to the battery. 33. Enter the customer s audio and navigation system (if equipped) anti-theft codes, and reset the XM radio presets. 34. Reset the clock. NOTE: Check the operation of the automatic day/night mirror according to the Operating Instructions supplied. Place the Operating Instructions in the glove box for your customer. A-PILLAR TRIM PIN H 28. Check that the left A-pillar trim and the pin are not damaged, then, install the new clip from the kit on the pin. 29. Position the clip at right angles near the hole in the left A-pillar. Install the clip by lightly pushing the left A-pillar trim at the part marked as SIDE CURTAIN AIRBAG. Check that the airbag is not pinched with the clip, and be careful not to push the left A-pillar trim excessively. A-PILLAR PANEL PART MARKED AS SIDE CURTAIN AIRBAG A-PILLAR TRIM of 8 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved