INSTALLATION INSTRUCTIONS
|
|
- Laurence Cobb
- 7 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Accessory S Application 2011 CR-V Publications No. AII Issue Date AUG 2010 PARTS LIST 2 Wire ties with clip A Back-up Sensors Attachment Kit P/N 08V67-SWA-100B Back-up sensor control unit Wire tie with clip B Wire tie with clip C Buzzer 2 EPT sealers Back-up sensor harness Fuse label 2 Self-tapping screws Back-up sensor subharness Flange nut 2 Corner sensor clips Accessory User s Information Manual Center sensor clips Back-up Sensors Kit P/N 08V67-SWA-100J Control unit bracket 2 Center sensors (STOP) (Blue) Connector clip 2 Corner sensors (STOP) 4 Wire ties (White) 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 08V67-SWA-1B of 14
2 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 8 mm, 10 mm, and 14 mm Sockets Pushpin Felt-tip pen Drill and 5 mm Drill bits 16 mm, 24 mm, and 26 mm Hole saws Scale Eye protection (safety goggles, face shield, etc.) 10 mm Combination wrench File Diagonal cutters Utility knife Plastic trim tool (T/N SILTRMTL 10) Blanket Isopropyl alcohol Shop towel T30 Torx bit Illustration of the Back-up Sensors installed on the Vehicle BACK-UP CORNER INSTALLATION FUSE (2A) CENTER S CORNER BUZZER BACK-UP CONTROL UNIT BG Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: If you are also installing a trailer hitch, install the back-up sensor kit first. 1. Make sure you have the anti-theft code for the radio and navigation system, then write down the radio presets. 2. Disconnect the negative cable from the battery. 3. If equipped, remove the tonneau cover. TONNEAU COVER Pull. 2 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
3 4. Remove the right rear door sill trim (three clips). RIGHT DOOR SILL TRIM 6. Remove the weatherstrip from around the rear trim panel. Remove the rear trim panel (two bolts with tie-down hooks, two clips, and four clips). 4 S 2 S 3 S TRIM B 2 TIE-DOWN HOOKS 5. Remove the cargo board (two hooks). WEATHERSTRIP 2 BOLTS B 7. Fold the rear seats forward, and remove the right rear lid from the cargo area right side trim (10 retaining tabs). CARGO AREA RIGHT SIDE TRIM RIGHT TRIM BRACKET CARGO BOARD HOOK B 10 RETAINING TABS BOLT RIGHT LID B 8. Remove the vehicle bolt from the right rear trim panel bracket American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 3 of 14
4 9. Remove the rear door and tailgate weatherstrip from the cargo area right side trim panel. 12. Remove the right quarter pillar glass trim (seven clips). 8 S WEATHERSTRIP 7 S RIGHT QUARTER PILLAR GLASS TRIM WEATHERSTRIP CARGO AREA RIGHT SIDE TRIM B B 10. Remove the cargo area right side trim panel (10 clips). 11. Remove the seat belt from the right quarter pillar glass trim (one cover and one seat belt bolt). NOTE: Torque the seat belt bolt to 32 N m (24 lbf ft). 13. Remove the left rear splash guard (four selftapping screws). RIGHT QUARTER PILLAR GLASS TRIM SEAT BELT BOLT COVER SPLASH GUARD 4 SELF-TAPPING SCREWS Y SEAT BELT B 14. Remove the right rear splash guard (four selftapping screws). 4 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
5 15. With the help of an assistant, remove the rear bumper (two bolt covers, two bolts, two flange bolts, and two clips). Place the rear bumper on a blanket. BOLT COVER 17. Get the back-up sensor harness. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the (2A ) label to the fuse case. FUSE CASE 2 FLANGE BOLTS FUSE LABEL (2A BACK-UP ) B 2 SCREWS A 18. If the vehicle is equipped with a moonroof, release the moonroof drain hose (two hooks). 16. If equipped, remove the rear bumper absorber from the rear bumper beam. HOOK BEAM MOONROOF DRAIN HOSE B ABSORBER B 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 5 of 14
6 19. Inside the cargo area, remove the clip that secures the vehicle 6-pin connector to the vehicle panel, and unplug the vehicle 6-pin connector. 22. Wrap one EPT sealer around the back-up sensor harness 6-pin connector, and secure the 6-pin connector to the vehicle harness with one wire tie. 6-PIN WIRE TIE EPT SEALER 6-PIN 6-PIN BACK-UP 6-PIN 6-PIN B 20. Plug the back-up sensor harness into the vehicle 6-pin connector. Plug the other vehicle 6-pin connector into the other back-up sensor harness 6-pin connector. 21. Reinstall the vehicle 6-pin connector clip to the vehicle panel. 6-PIN 120 mm EDGE EPT SEALER BACK-UP AB 23. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the EPT sealer will attach. Attach the EPT sealer to the edge of the vehicle panel in the area shown. 24. Slide the control unit bracket onto the control unit as shown. CONTROL UNIT B CONTROL UNIT BRACKET AB 6 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
7 25. Plug the back-up sensor harness 14-pin connector into the control unit. 28. Install the back-up sensor harness clip into the hole in the vehicle panel. CONTROL UNIT CONTROL UNIT BRACKET 14-PIN B 26. Attach the back-up sensor harness clip to the control unit bracket. 27. Insert the stud on the control unit bracket into the hole in the vehicle panel, making sure that the bracket tab is seated in the large hole. Secure the bracket to the vehicle panel using a 6 mm flange nut. 29. Using a utility knife, trim the right quarter pillar glass trim in the area shown. RIGHT QUARTER PILLAR GLASS TRIM B CONTROL UNIT CONTROL UNIT BRACKET STUD UTILITY KNIFE BRACKET TAB 5 mm Cut off. RIB AB LARGE 6 mm FLANGE NUT B 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 7 of 14
8 30. Using a scale and a felt-tip pen, measure and mark the right quarter pillar glass trim in the area shown. 33. Using a pushpin, pierce the center marked position of the right quarter pillar glass trim. RIGHT QUARTER PILLAR GLASS TRIM S FELT-TIP PEN 16 mm 20 mm 20 mm RIB RIB 22.5 mm 6.5 mm RIB 31. Using a pushpin, pierce the two outer marked positions of the right quarter pillar glass trim. S 6.5 mm BB 5 mm BIT RIGHT QUARTER PILLAR GLASS TRIM BIT AB 34. While wearing eye protection, drill the pierced center mark to 16 mm. First drill with a drill bit, and finish with a 16 mm hole saw. Remove any burrs. 35. Using isopropyl alcohol on a shop towel, clean the right quarter pillar glass trim where the double-sided tape will attach. Remove the adhesive backing from the buzzer. Route the buzzer 2-pin connector through the 16 mm hole, and install the buzzer to the right quarter pillar glass trim with two self-tapping screws. Install it with the on/off switch and the volume control toward the front of the vehicle. RIGHT QUARTER PILLAR GLASS TRIM DOUBLE-SIDED TAPE SWITCH BUZZER ADHESIVE BACKING RIGHT QUARTER PILLAR GLASS TRIM B VOLUME CONTROL 32. While wearing eye protection, drill the two pierced marks to 5 mm. First drill with a drill bit, and finish with a 5 mm drill bit. 5 mm 16 mm 5 mm 2 SELF- TAPPING SCREWS BUZZER 2-PIN B 36. Reinstall the right quarter pillar glass trim. 8 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
9 37. Plug the back-up sensor harness 2-pin connector into the buzzer 2-pin connector. 41. At the right rear corner of the vehicle, remove the vehicle grommet. Without a Vehicle Harness WIRE TIE WITH B 2-PIN BUZZER 6-PIN GROMMET WIRE TIE cargo area outside 2-PIN BUZZER 2-PIN 38. Secure the 2-pin connector: 2-PIN BB With a vehicle harness, secure the 2-pin connector to the vehicle harness with a wire tie. Without a vehicle harness, secure the 2-pin connector to the vehicle panel with one wire tie with clip B. 39. Secure the back-up sensor harness to the vehicle harness with one wire tie. BUZZER B 42. Route the back-up sensor subharness 6-pin connector through the hole where the vehicle grommet was removed, and seat the back-up sensor subharness grommet into the vehicle panel hole. 43. Install the connector clip to the back-up sensor subharness 6-pin connector. BACK-UP GROMMET (Discard.) 6-PIN 6-PIN BUZZER Bundle up the excess. BACK-UP BACK-UP WIRE TIE WIRE TIE WITH C AD 40. Bundle up the excess buzzer harness, and secure it to the vehicle panel with one wire tie with clip C. 6-PIN B 44. Plug the back-up sensor subharness 6-pin connector into the back-up sensor harness 6-pin connector, and install the connector clip. Secure the clip in the vehicle panel hole in the area shown American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 9 of 14
10 45. Route the back-up sensor subharness as shown, and install the back-up sensor subharness clip into the vehicle panel hole. 46. Route the back-up sensor subharness as shown. Install the back-up sensor subharness clips into the holes in the vehicle panel. With rear bumper beam: Secure the subharness to the rear bumper beam with one wire tie at the green tape. GREEN TAPE WIRE TIE BEAM BEAM AG Without rear bumper beam: Secure the subharness to the stud on the vehicle panel with one wire tie with clip A at the green tape. WIRE TIE WITH A GREEN TAPE 47. Route the back-up sensor subharness as shown. With rear bumper beam: Secure the subharness to the rear bumper beam with one wire tie at the green tape. BEAM BACKUP SUB BACKUP SUB GREEN TAPE AG WIRE TIE STUD BEAM AG AG 10 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
11 Without rear bumper beam: Secure the subharness to the stud on the vehicle panel with one wire tie with clip A at the green tape. GREEN TAPE WIRE TIE WITH A 49. Inside the rear bumper on the passenger s side, locate the two back-up sensor scribe marks. Using a pushpin, pierce the center and top for both the outboard and the inboard scribe marks. There are several marks on the inside of the rear bumper; make certain that you locate and pierce the proper scribe marks. OUTBOARD INBOARD STUD AG 48. Inside the rear bumper on the driver s side, locate the two back-up sensor scribe marks. Using a pushpin, pierce the center and bottom of the outboard scribe marks, and pierce the center and top of the inboard scribe marks. There are several marks on the inside of the rear bumper; make certain that you locate and pierce the proper scribe marks AB INBOARD OUTBOARD AB 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 11 of 14
12 50. While wearing eye protection, drill a hole at each of four pierced points you made in the center of the rear bumper. NOTE: Drill from the painted side of the bumper. 52. While wearing eye protection, drill a hole at each of four pierced points you made in each corner of the rear bumper. NOTE: Drill from the painted side of the bumper. BIT 2 S BIT 2 S 26 mm SAW 24 mm 24 mm SAW 26 mm 26 mm AG 24 mm SAW 24 mm Passenger s side of the bumper. 2 S BIT AG Driver s side of the bumper. Enlarge the lower holes using a 26 mm hole saw. Enlarge the upper hole using a 24 mm hole saw. Passenger s side of the bumper. 51. Enlarge the lower holes using a 26 mm hole saw. NOTE: Drill from the painted side of the bumper. Remove all burrs. Driver s side of the bumper. Enlarge the lower hole using a 24 mm hole saw. 53. On the passenger s side of the bumper, enlarge the bottom hole to 24 mm using a 24 mm hole saw. On the driver s side of the bumper, enlarge the upper hole to 24 mm using a 24 mm hole saw. NOTE: Drill from the painted side of the bumper. Remove all burrs. 12 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
13 54. On the passenger s side of the rear bumper, install the corner sensor (white) and the center sensor (blue) to the rear bumper using one corner sensor clip, and one center sensor clip. Be sure the sensors are seated properly. 55. On the driver s side of the rear bumper, install the corner sensor (white) and the center sensor (blue) to the rear bumper using one corner sensor clip, and one center sensor clip. Be sure the sensors are seated properly. 26 mm CENTER CENTER (Blue) CENTER (Blue) CENTER (Blue) 26 mm CENTER (Blue) CENTER 24 mm 24 mm CORNER (White) CORNER (White) CORNER AG CORNER (White) CORNER CORNER (White) AG 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1008) 13 of 14
14 56. If the vehicle is equipped with a rear bumper absorber, use a utility knife to trim each end of absorber using the measurements and scribe marks shown. 58. With the help of an assistant, bring the rear bumper near the vehicle, plug in the four back-up sensor subharness 2-pin connectors into the sensors, and attach the two subharness clips to the two center sensor clips. Reinstall the rear bumper. UTILITY KNIFE 30 mm Cut off. 4 2-PIN S CORNER ABSORBER Cut off. 50 mm UTILITY KNIFE CENTER CENTER CORNER CENTER (White) 2 BACK-UP S AG ABSORBER 57. Reinstall the rear bumper absorber to the rear bumper beam B 59. Check that all wire harnesses are routed properly and that all connectors are plugged in. 60. Reinstall all removed parts. 61. Reconnect the negative cable to the battery. 62. Enter the anti-theft codes for the radio and navigation systems, then enter the customer s radio presets. 63. Reset the clock. 64. Check that the back-up sensors work properly as described in the Accessory User s Information Manual supplied with the back-up sensor attachment kit. 14 of 14 AII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2003 ACCORD 4 DOOR AII 24378 Issue Date MARCH 2003 The XM Radio will not fit in a vehicle equipped with a rear entertainment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationInstallation Instructions
Installation Instructions Page 1 of 16 January 2008 Equipment Parts, Trailer Hitch Ver 3.0 Accessory Development SUBJECT TRAILER HITCH KIT (US Only) - P/N 71 60 0 413 359 MODEL X5 (E70): Select Vehicle
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationInstallation Instructions
Installation Instructions For Use with PXPV230, PXPV265, PXPD230, and PXPD265 models Attention! - Please read these instructions completely before attempting installation. Always unplug the power supply
More informationTOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationTOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation
TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More information2003 ACCORD - Automatic Transmission Removal
2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationPOWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents
-J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English
More informationC5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like... First you flip
More information2002 2005 Mini Cooper S Grille Install Instructions
2002 2005 Mini Cooper S Grille Install Instructions Lower Front Grille BEFORE AFTER Package Contents 1 perforated grille (Stiletto, RAZR, or Monster) 6 Zip Tie Mounting Pads 1 is for the temp. sensor 5
More informationConvertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995)
Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995) Written by Samit Ghosh with picture material from vexed of benzworld.org
More informationTOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600
07-08 TOYOTA FJ CRUISER, 05-09 SIENNA, 06-08 SCION TC PART NUMBER: 250-1732 1 CRUISE CONTROL KIT TOOL SVC NUMBERS: 250-2598, 250-2600 2 2 1 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationINSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART #
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationUNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS
UNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS CONTENTS Parts List... 2 Parts Diagram... 2 Helpful Hints... 3 Installation... 4 Operation and Troubleshooting Guide... 6 Warranty Information... 8 Form #3132,
More informationGuide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:
Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in
More informationCOMPONENTS IP 2 INSTRUMENT PANEL INSTRUMENT PANEL ASSEMBLY ASSIST GRIP RETAINER RH FRONT PILLAR GARNISH RH FRONT DOOR OPENING TRIM WEATHERSTRIP RH
INSTRUMENT PANEL INSTRUMENT PANEL INSTRUMENT PANEL PRECAUTION 1 1. PRECAUTION FOR VEHICLE WITH SRS AIRBAG AND SEAT BELT PRETENSIONER (a) Some of these operations may affect the SRS airbag system. Read
More informationSCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4
Preparation 2.0L F-4 Part Number: PTR03-18130 Please see Page 12 for important Care and Maintenance information! Kit Contents Item # Qty. Service Part # Description 1 1 PTR03-18130-AC TRD Air Box Base
More information- power windows - alarm system - electric door mirror control - door warning light - central locking - seat memory
Door Wiring Harness Plug Connections Binder -, Electrics Vehicle Type: (86) Model Year: 7 (V) Concern: Door wiring harness plug connections X11 / X12. Information: The rubber boot for the door connector
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions R5 5 Z CD changer retrofit kit MINI (R 5 and R 53) LHD and RHD The installation time is approx..5 hours, but this may vary depending on the condition of
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationINSTALLATION MANUAL INSIDE PASSENGER COMPARTMENT. HFC 134a FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH
HFC 134a Ozone Friendly Refrigerant FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH AAAMU-60 / INSIDE PASSENGER COMPARTMENT INSTALLATION MANUAL 2000 (EUROPE) B.V.. All Rights Reserved. This
More informationBACKUP CAMERA JEEP COMMANDER/GRAND CHEROKEE
BACKUP CAMERA 1 JEEP COMMANDER/GRAND CHEROKEE 2 Call Out Description Parts Quantity 1 Tie Wrap-Nylon 6.9" Supplied in kit 12 2 Camera, Rear View Supplied in kit 1 3 Camera Extension Harness Connector Supplied
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationSB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V
INSTALLATION GUIDE for the SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationSECURITY SYSTEM SMART SIREN KIT
-J00876 REV. 009-0-09 SECURITY SYSTEM SMART SIREN KIT GENERAL Kit Number 688-0 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationInstallation instructions, accessories - Handsfree for cellular phone, system B, entry level
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18
More informationCUSTOM AUXILIARY FORWARD LIGHTING KIT
-J0 REV. 0--0 CUSTOM AUXILIARY FORWARD LIGHTING KIT GENERAL Kit Number -0, 0000 Models This Custom Auxiliary Lighting Kit adds lamps and turn signals to 00 and later FLHX model motorcycles. Additional
More informationBMW Parts and Accessories Installation Instructions
BMW Parts and Accessories Installation Instructions Retrofit Anti-theft Alarm System (DWA) series-identical retrofit for BMW 5 Series saloon and touring (E 9, E 9/) left-hand drive F 9 005 W Installation
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (748-547) Chrysler 300 2005 10, Dodge Magnum 2005 08, Dodge Charger 2006 09 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationINSTALLATION INSTRUCTIONS MULTI-MOUNT KIT Part Number: 75330 Application: Warn HP PowerPlant P/N 71800
INSTALLATION INSTRUCTIONS MULTI-MOUNT KIT Part Number: 75330 Application: Warn HP PowerPlant P/N 71800 Your safety, and the safety of others, is very important. To help you make informed decisions about
More informationFigure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.
Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help
More informationInstallation instructions, accessories - Navigation system, RTI
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 4/8.8 2007 08 Page 1 of 20 Required tools A0000162 IMG-239667 IMG-239664 IMG-239980 IMG-242205 R8802817 R3905015 Page 2 of 20 R3903812 IMG-213320 Page
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationSALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT
SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT INSTALLATION MANUAL: 2005 MUSTANG 4.6 3V MANUAL P/N: 10-8002-C14338C SUPERCHARGER KIT P/N: 10-1607-B14083* Saleen Performance, Inc. 1225 East Maple Rd.,
More informationTABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
More informationFRONT WINDSHIELD SEAL INSTALLATION
FRONT WINDSHIELD SEAL INSTALLATION Tech Article From Newsletter 16.1-1st Quarter of 2010 Replacing your Front Windshield Seal ISN T AS HARD AS YOU MAY THINK! Recently, we retooled our front window seal
More informationBILLET HEADLAMP WITH SHORT/TALL MOUNTS
-J099 REV. 00-0- BILLET HEADLAMP WITH SHORT/TALL MOUNTS GENERAL Kit Number 9-0, 9-0 Models Kit 9-0 is a -/ inch headlamp and kit 9-0 is a -/ inch headlamp. Both kits will fit the models listed in Table.
More informationREAR SHOCK ABSORBER WITH COIL SPRING
278 OVERHAUL COMPONENTS: see page 272. 1. REMOVE TONNEAU COVER ASSY (SEE PAGE 7627) 2. REMOVE DECK BOARD SUBASSY (SEE PAGE 7627) 3. REMOVE BACK DOOR SCUFF PLATE (SEE PAGE 7627) 4. REMOVE DECK FLOOR BOX
More informationFront brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
More informationTrailblazer, Envoy, Rainier, Ascender
6. After removing the trim plate bezel simply remove the four ¼ screws holding the instrument cluster in place. Pull the cluster out and unplug the single wiring harness connection in the back. Trailblazer,
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationEZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-21 Case IH Puma 165 Puma 180 Puma 195 Puma 210 New Holland T7030 T7040 T7050 T7060 Revision A June 2007 Part Number 53345-21-EU2
More information741-760 INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-760) Chevy Cavalier, Pontiac Sunfire Coupe 1996 2005 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave
More informationMazda CX7 2010-up 99-7520B
INSTALLATION INSTRUCTIONS FOR PART 99-7520B APPLICATIONS Mazda CX7 2010-up 99-7520B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationBack-Up Camera Installation Guide
Hz Hz In This Guide: Back-up camera installation requires connecting power wiring to the existing reverse lighting circuit and adding a chassis ground, as well as routing a video signal cable to the front
More informationUB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS
UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS: Carefully read these instructions before installing your new air-conditioner. AUSTRALIAN AUTOMOTIVE AIR AL00500054E 1 Table
More informationCOOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
More informationOVEN PARTS For Models:RBS305PDB16, RBS305PDQ16, RBS305PDT16, RBS305PDS16 (Black) (Designer White) (Biscuit) (S.Steel)
OVEN PARTS 30" BUILT IN ELECTRIC OVEN SELF CLEAN 10 04 Litho in U.S.A.(cre) 1 Part No. OVEN PARTS 1 Literature Parts LIT8300654 Installation Instructions LIT8300772 Use & Care Guide (Oven) LIT8301758 Tech
More informationVW Jetta, Golf, New Beetle 1.9L TDi Unichip PnP Installation Instructions
VW Jetta, Golf, New Beetle 1.9L TDi Unichip PnP Installation Instructions and Warranty Information Tools Required 10mm combination wrench, 13mm Socket (Jetta/Golf only), 3/8-inch or ¼-Inch drive ratchet,
More informationParts and Accessories. Installation Instructions.
Parts and Accessories. Installation Instructions. Rear-view camera retrofit MINI ONE (R 50) MINI COOPER (R 50) MINI COOPER S (R 53) These installation instructions are only valid for cars with SA 609 (navigation
More information2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13)
2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13) Exploded View Special Tools Required Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool 07GAF-SD40100 Bearing driver attachment,
More informationInstallation instructions, accessories. Cruise control. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No. 30739998 1.
Instruction No Version Part. No. 30739998 1.1 Cruise control Page 1 / 11 Equipment A0000162 A0000161 A0801178 D8802049 Page 2 / 11 M8802108 Page 3 / 11 IMG-223164 Page 4 / 11 IMG-213320 Page 5 / 11 INTRODUCTION
More informationMGA Alternator Conversion
MGA Alternator Conversion Installation Instructions For 1955 to 1962 MGA PART # 130-078 and #130-088 440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com
More informationMFH-5057 Ford Small-Block V-8 Fresh Water Cooling Kit Instructions
MFH-5057 Ford Small-Block V-8 Fresh Water Cooling Kit Instructions MONITOR PRODUCTS, INC. 15400 Flight Path Dr Brooksville, FL 34604 Tel: 1-800-334-4591 or 352-544-2620 Sales: ext 201 Technical Support:
More informationLIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions
LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More informationBODY 42-1 CONTENTS 42109000201. TRUNK LID <Sedan>... 4 FENDER... 6 FUEL FILLER DOOR... 7 WINDOW GLASS... 8 SERVICE SPECIFICATIONS... 19 TRUNK LID...
42-1 BODY CONTENTS 42109000201 HOOD... 3 TRUNK LID ... 4 TRUNK LID... 4 FENDER... 5 SEALANT... 5 FENDER... 6 FUEL FILLER DOOR... 7 WINDOW GLASS... 8 ADHESIVES... 8 SPECIAL TOOLS... 8 WINDOW REPAIR...
More informationSECURITY SYSTEM SMART SIREN II KIT
-J08 REV. 0-0- SECURITY SYSTEM SMART SIREN II KIT GENERAL Kit Numbers 688-06A, 688-06B Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com
More information2003 Audi A4. AUDI' '3.0L V6 - AVK Engine - A4 & A6
Installation (A4) CAUTION: Before installation, ensure camshafts are aligned, crankshaft is locked in place and camshaft gear bolts are loose as described in removal procedures. When turning camshaft,
More informationArctic Leash Instruction Manual Alaskan Products Company LLC.
Retractable Cord Reel for Engine Block Heaters Arctic Leash Instruction Manual Alaskan Products Company LLC. INSTALLATION INSTRUCTIONS This instruction manual is a reference guide for installing and operating
More informationADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
More informationStep 1. Item 6. Item 1
Voltage Regulators QD3/T350 Motor Replacement Kit Kit Number 57A63675100B Service Information S225-50-35 Contents General..................................... 1 Parts Supplied...............................
More informationspecializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationBoxster. Technical Information. Service 3/99 9415. Litronic Retrofit Kit
Litronic Retrofit Kit 9 3/99 9415 Binder - 9, Electrics This bulletin replaces bulletin Grp. 9, #3/99, dated 5-20-99. Vehicle Type: Model Year: Concern: Information: As of 1997 (V) Retrofitting Litronic
More informationUse subject to terms and conditions posted at http://www.burgertuning.com/terms.htm
Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING VEHICLES AS DEFINED UNDER CALIFORNIA LAW, AND IS NOT LEGAL FOR
More informationInstallation instructions, accessories. Alarm, siren. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No. 30633795 1.
Instruction No Version Part. No. 30633795 1.0 Alarm, siren Page 1 / 12 Equipment A0000162 A0000161 A0801178 IMG-233902 Page 2 / 12 IMG-213320 Page 3 / 12 INTRODUCTION Read through all of the instructions
More information