Owner s Manual DLS AMPLIFIER ONE

Transcription

1 Owner s Manual DLS AMPLIFIER ONE Audio for Life The information contained in this manual is subject to change without prior notice. The most current version of this manual is available on our official website at: Copyright c DLS Svenska AB. All rights reserved

2 Table of contents Congratulations.. 1 Unpacking... 1 Quick setup guide Introduction Installation and placement Cleaning... 2 Front panel controls Rear panels connections.. 4 Settings Remote control Operating.. 7 Warranty... 8 Obtaining service 8 Troubleshooting... 8 Your own notes... 9 Technical specifications Output power: 2 x 8 ohm, 2 x 4 ohm Minimum amplifier load: 4 ohm Analogue inputs: 1 pair balanced (XLR), 4 pair unbalanced (RCA) Input impedance: 50 kohm Frequency response: DC 100kHz +/- 1 db Signal to noise ratio: > 106 db Harmonic distortion (THD): < 0,05% 20 Hz 20 khz Channel separation: > 100 db AC power requirements*: 120 V / 60 Hz or 240 V / 50 Hz Power consumption@ idle: 30 W Power consumption in Standby: 15 W Dimensions (WxDxH): 432 x 432 x 128 mm (17 x 17 x 5,04 inches) Weight: 16 Kg ( 35 lbs) *Connect the AMPLIFIER ONE only to an AC source of the proper voltage. A label on the rear panel will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the warranty Marking by the CE symbol indicates compliance of this device with the EMC (Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the European Community This product must be returned to the separate col lec tion system for electronic products. Do not dis po se this product together with general household waste.

3 Congratulations! Thank you for selecting the DLS AMPLIFIER ONE as a part of your music system. When we designed this amplifier, we decided to enter with A Big Bang. This amplifier has a hightech interior, but a no-nonsense, user-friendly exterior. The amplifier has been designed and assembled by highly skilled DLS craftsmen to offer state-ofthe-art high-end performance in a luxury elegant package. We have spared no effort to ensure that it is one of the finest two-channel integrated amplifiers available in its class. We hope you enjoy listening to the AMPLIFIER ONE as much as the pride we have taken in creating this audio product. Before setting up your AMPLIFIER ONE, please read this manual thoroughly to assure yourself with its features. Unpacking The DLS AMPLIFIER ONE should be removed from its box with care. The following accessories should be included inside the box together with your AMPLIFIER ONE: 1. R4U remote control 2. Two AAA batteries 3. AC power cable 4. This owner s manual As soon as the amplifier is safely removed from it s box, perform a thorough physical inspection and report any damage to your dealer immediately. We suggest that you keep all of the original packaging material, storing it in a safe, dry place in the event that you need to transport the amplifier. Please write the serial number of the AMPLIFIER ONE (on rear panel) in the space provided below for future reference: Serial No: Date of purchase: Dealers name: Quick setup - Carefully unpack your AMPLIFIER ONE. - Connect your input source to the amplifier. - Connect your loudspeakers to outputs connectors properly. - Connect the AC cable to the amplifier and to an AC wall outlet. Make sure you connect to the proper voltage marked on your amplifier. - Set the main switch (at the back panel on the amplifier) to ON. - Wait during the Warming-up period is ready (approx sek.). - Push the Standby button (on the front pa nel) to ON. - Choose the input source at the left side on the front panel, with the rotary source control. NOTE: The amplifier need a BURN-IN period for approx. 400 hours. (for more information read the Introduction on page 2). 1

4 Introduction A BURN-IN or BREAK-IN period is required before the amplifier will reach its max i mum sonic potential. The performance of your AMPLIFIER ONE will continue to improve during the first 400 hours of listening. A Burn-in period is required for the numerous high quality electronic parts used in this integrated amplifier. We recommend the amplifier to be left on, or in Standby mode at all times, especially during the first 5-6 weeks of operation, in order to speed up the BURN-IN pro cess. The amplifier should not be switched off by using the main switch at the rear panel, unless it will be out of use for a significant period of time during vacations etc. Installation and Placement The AMPLIFIER ONE requires reasonable ventilation to maintain an optimum and consistent operating tem pe ra tu re. As a result, it should be placed in a location with empty space around it for proper heat dissipation. As well, it should be placed on a solid level surface. You should never place the amplifier too close to heat sources such as radiators, stoves, fireplaces or other heat-producing appliances, or inside a closed cabinet. Avoid placing the amplifier where it will be subjected to direct sunlight or extremely low temperature. Avoid placing the amplifier near electromagnetic fields, such as large power amplifiers etc. Placement of the unit near these fields can lead to problems with hum. NOTE: You should never place another component directly on top of this AMPLIFIER ONE. Cleaning To clean the AMPLIFIER ONE, use only a soft tissue. Never apply abrasive cleaners to the surfaces of the unit. At no time should liquid cleaners be applied directly to the AMPLIFIER ONE, as direct application of liquids may result in damage to electronic components within the unit. 2

5 Front panel controls On the front panel you have two rotary controls and one push button. These three controls let you operate your AMPLIFIER ONE in daily use, or if you prefer, use the remote control R4U which is included. 1. Standby Press this push button and the amplifier will turn on. The display will show input source and amplifier level. Push the button once more and the amplifier will go back into Standby mode. The display will now be dark. For best performance, the AMPLIFIER ONE should be left on, or in the Standby mode at all times. When in Standby mode all audio circuitry remains powered up to maintain optimal performance. When switching back from Standby to the on mode, Input and Volume level settings will be memorized from the previous listening session. 2. Source Use the left rotary control to select the input source. The AMPLIFIER ONE has five inputs: 1 pair balanced (XLR), and 4 pair unbalanced (RCA). If you want, you can rename the input names in the display More about this under chapter 5, Input Settings. 3. Display In normal mode the display shows selected input and volume level. In setting mode the display will show actual status of the settings. 4. Volume Use the right side rotary control to set output level (from mini mum 0, to maximum 85)

6 Rear panel connections 1. Mains Power Input and Fuse Plug the AC cord firmly into the AC jacket. Make sure you connect to the proper voltage marked on your amplifier. Connect the male end directly to an AC wall outlet. Avoid use of an extension cord or power split since these often degrade sound quality The mains power switch turns the Amplifier totally off. In the fuse box you will also find a spare main fuse. Please check that it is the same value before switching fuse. 2. Balanced Inputs Intended to be used if your main source has XLR-outputs. If your source/sources are not equipped with XLR-outputs, please use the line inputs with RCA-connectors. 3. Unbalanced Inputs Line: 1, 2, 3 and Tape Each input has the same input sensitivity and impedance. They are compatible with any typical analogue line level source: CD, DVD, MD, Laserdisc, VCR, DA-converter, Tape deck or phono preamplifier. 4. Tape Out Fixed Level Output for external equipment. 5. Pre Out If you want to use your AMPLIFIER ONE as a pre-amp, just connect your power amplifier to the Pre Out with RCA connectors. 6. Output Connectors Speaker connectors. Marked + (Red) and (Black). Connect to the corresponding connectors on your loudspeakers

7 Settings Use the remote control, press the DISP EDIT button and step through the following settings: Balance Input Level Software Version Edit Input Name IR Input Front (not in use) Software Version Back to Normal Display Mode (Input and Volume). NOTE: If you do not push any button within 3 seconds, the amplifier will leave the setting mode. Balance Adjustment for Left and Right channel level. Press Vol+ to increase Left channel, or Vol- to decrease Right channel. Input Level To change the input level, select the input you wish to change, then step through the menu by pressing DISP EDIT until INPUT LEVEL is shown in the display To adjust the input sen si tiv ity, simply press VOL+ to increase the input sensitivity, or VOL- to decrease the sensitivity When the desired level is set, exit the menu by pressing the DISP EDIT button until your input name is displayed again, or wait a few seconds. Your new level is now stored in the memory You may store a different level for each input as they are stored independently in the memory If you do not wish to use this feature, leave as is, the inputs are factory preset to level 0 (max +9, min -9). Software Version Displays the software version. Edit Input Name The display uses maximum 8 character (of totally 14) to show Input Name in the display. Select the Input you want to change by using the SOURCE +/- buttons. Press the DISP EDIT button to activate the menu and step until EDIT INP NAME is shown in the display Press VOL + and you will see the first character of your previously selected input name flash. Use VOL +/ - to change the character. Go to the next character by using the SOURCE+/- button. Then use the VOL +/- to change the character, etc. To exit the menu, press DISP EDIT until the new name is display ed or wait a few seconds. IR Input Front Not in use NOTE: The AMPLIFIER ONE is equipped with a non-volatile memory that will remember all of the settings you have edited, (Volume, Input selection, Alias names, etc.) that you used before placing the unit into standby mode or switched the unit off totally by the mains switch. 5

8 Features Use the remote control to enter the following Features: Surround Mode and Tape Loop Surround Mode To bypass the preamplifier section of the AMPLIFIER ONE, press the SURR button on your remote control for 1 second. SURR will be displayed next to your currently selected input. NOTE: In this mode Line 4 (TAPE) will be directly connected to the power amplifier bypassing the internal preamplifier circuits. WARNING: Do not press Surround Mode if you don t use an external Surround preamplifier. Tape Loop If you want to use any external Line Level equipment (such as Surround processor, Digital Room correction unit or similar equipment) connect as follow: TAPE OUT to external equipment Input, and Output from the equipment to TAPE IN at the AMP- LIFIER ONE. By pressing Tape Loop on the remote control, you now loop the signal through the external equipment. Remote control R4U The same remote is used for both AMPLIFIER ONE and CD ONE. The functions used to control the amplifier are bold in the text below AMP Changes the AMPLIFIER ONE between ON and Standby mode 2. CD Changes the CD ONE between ON and Standby mode 3. DIM AMP Dims the display at AMPLIFIER ONE in three steps and off 4. DIM CD Dims the display at the CD front panel in three steps 5. TAPE LOOP Loop signal to external equipment 6. RANDOM Random play for Compact disc 7. SURR Press the button for 1 second to entry SURROUND mode 8. TIME Displays track and elapsed time of track or CD 9. DISP EDIT Editing display on amplifier 10. MUTE AMP Mute control button for the amplifier, mutes to "0" Output level 11. SOURCE Use - or + to change the input source 12. VOL Output level + / Stop playing disc 14. Play disc 15. Open / Close CD drawer 16. Pauses playing disc 17. t Restart current track, or step to previous track 18. Step to next track 19. tt t Reverse Scan 20. Forward Scan 21. REPEAT Repeat track (press once), Repeat Disc (press twice) To cancel press until Repeat Off shows in Display 22. CD/SACD In Stop-mode: Changes between SACD-STEREO t t t tt t

9 Operating We recommend that you leave your AMPLIFIER ONE powered up at all times to maintain optimal performance. If you plan to be away from your home for a few days, powering off the amplifier may not be a bad idea. Don t forget, if you do so, it will require several hours before it reaches its peak performance after you ve powered up again! Turning on your AMPLIFIER ONE for the first time When you turn the amplifier on for the first time, make sure that every cable is properly connected to avoid any problems. Then turn on your amplifier in the following manner: 1. Turn on the main switch labelled POWER to the position ON at the rear side. Make sure you connect to the proper voltage marked on your amplifier. You will now see WARMING UP in the display window, wait a few seconds until the message disappear. 2. Press the STANDBY button on the front side, the display window will now display the Source and Volume level. 3. Select input line. 4. Adjust the Volume to a reasonable listening level. The R4U remote control Functions used to control AMPLIFIER ONE are shown below, all the other buttons are only used to control CD ONE

10 Warranty Contact your authorized DLS Dealer for details of our local warranty policy Obtaining service If your DLS AMPLIFIER ONE must be serviced, please contact your local dealer. You can also consult the DLS web-site and contact the exclusive Hi-Fi distributor for your country Important! It is extremely important that the in for ma tion about a problem is explicit and complete. A specific, comprehensive description of the problem helps your dealer and the technical service department to locate and repair the fault as quickly as possible. A copy of the original bill or sales receipt will serve to verify the warranty status. Please include it with the unit when it is brought in for warranty service. Warning! All returned units must be properly packaged in their original packaging material. If the packaging to protect the unit is, in our opinion or that of our dealer, inadequate, we reserve the right to repackage the return shipment at the owners expense. Neither DLS nor your dealer can be responsible for shipping damage due to improper (that is, non-original) packaging. Your dealer can order a new set of shipping materials for you if you need to ship your AMPLIFIER ONE and no longer have the original materials. There will be a charge for this service. We strongly recommend saving all packaging materials in case you need to ship your unit some day Troubleshooting Problem: Cause: Solution: No sound Power AC Mains cable unplugged or power not switched on Tape Loop is selected Mute on Internal fuse blown Input cable disconnected External Electrical Shock Check if AC Mains cable is plugged in and power switched on De-select Tape Loop mode Switch off Mute Consult dealer Connect Input cable Switch Off Main Power for minimum 5 seconds No sound in one of the channels Speaker not properly connected or speaker damaged Input lead disconnected or damaged Check connectors and speakers Check leads and connections Weak bass/poor stereo image Speakers wired Check connections to out of phase speakers in the system 8 Remote control not working Batteries need to be replaced or are incorrectly installed IR transmitter or receiver windows obstructed Replace or check the batteries Remove obstruction

11 Your own notes Make you own notes regarding settings, installation etc. 9

12 Contact: DLS Svenska AB P.O Box SE Göteborg SWEDEN Phone: Fax: