SMPS Capacitors Chip Assemblies
|
|
|
- Juniper Welch
- 7 years ago
- Views:
Transcription
1 MP Capacitors CH/CV - Radial, Dual-in-ine, 4 Terminal/MT J & Ranges European Preferred s 10nF to 180 µf B9100 approved 50V to 500 VDC ow ER/E -55ºC to +125ºC 1B/C0G and 2C1/X7R Dielectrics This range allows MP engineers to select the best volumetric solution for input and output filter applications in high reliability designs. Utilizing advanced multilayer ceramic techniques to minimize ER/E giving high current handling properties appropriate for filtering, smoothing and decoupling circuits. EECTRICA PECIFICATION Temperature Coefficient CECC , (4.24.1) 1B/C0G: A Temperature Coefficient - 0 ± 30 ppm/ºc, -55º to +125ºC 2C1/X7R: C Temperature Characteristic - ± 15%, -55º to +125ºC Capacitance Test 25ºC 1B/C0G: Measured at 1 VRM at 1KHz (1MHz for 100 pf or less) 2C1/X7R: Measured at 1 VRM at 1KHz Dissipation Factor 25 C 1B/C0G: 0.15% at 1KHz, 1 VRM (1MHz for 100 pf or less) 2C1/X7R: 2.5% at 1KHz, 1 VRM Insulation Resistance 25 C 1B/C0G & 2C1/X7R: 100K megohms or 1000 megohms-µf, whichever is less Dielectric ithstanding Voltage 25 C (Flash Test) 1B/C0G & 2C1/X7R: 250% rated voltage for 5 seconds with 50 ma charging current. (500 Volt 150% rated voltage) Dielectric ithstanding Voltage 25 C (Flash Test) 1B/C0G & 2C1/X7R: 250% rated voltage for 5 seconds with 50 ma charging current. (500 Volt 150% rated voltage) ife Test (1000 hrs) CECC (4.23) 1B/C0G & 2C1/X7R: 200% rated voltage at +125ºC. (500 Volt 120% rated voltage) Damp Heat IEC , 56 days. Thermal hock IEC ºC to +125ºC, 5 cycles Resistance to older Heat IEC Vibration IEC Hz Hz, 0.75mm or 98m/sec 2, 6 hrs. Bump IEC m/sec 2, 4000 bumps MARKING CH and CV 4x, 5x, A5C 225K xxxxxx Top line A (AVX). Voltage code, dielectric code. Middle line capacitance code, tolerance code. Bottom line 6 digit batch code. Other CH, CV s AVX 5C 156M xxxxxx Top line AVX. econd line voltage code, dielectric code. Third line capacitance code, tolerance code. Bottom line, 6 digit batch code. 28
2 MP Capacitors (CV ) European Preferred s VERTICAY MOUNTED RADIA PRODUCT Part Number format (CVxxxxxxxxxxxA2) Typical Part Number CV525C106MA30A2 H Max. T Max. Max. H ead Dia CV (0.417) 8.7 (0.342) 8.2 (0.322) 0.7 (0.028) CV (0.468) 10.7 (0.421) 10.2 (0.400) 0.9 (0.035) CV (0.649) 13.6 (0.535) 15.2 (0.600) 0.9 (0.035) CV (0.700) 21.6 (0.850) 15.2 (0.600) 0.9 (0.035) CV (0.893) 16.6 (0.653) 21.2* (0.834) 0.9 (0.035) *Tolerance ± 0.8 ead Dia. ee Table 25 (0.984) ±3 (0.118) ±0.5 CV41/51/61/71/ (0.150) CV42/52/62/72/ (0.291) CV43/53/63/73/ (0.437) CV44/54/64/74/ (0.583) VERTICAY MOUNTED 4 TERMINA RADIA PRODUCT Part Number format (CVxxxxxxxxx3xx4) Typical Part Number CV435C106MA30A4 M1 T Max. H Max. M1 = M2 ± (0.984) ±3 (0.118) ead Dia. ee Table M2 Max. H ead Dia CV (0.417) 8.7 (0.342) 8.2 (0.322) 0.7 (0.028) CV (0.468) 10.7 (0.421) 10.2 (0.400) 0.9 (0.035) CV (0.649) 13.6 (0.535) 15.2 (0.600) 0.9 (0.035) CV (0.700) 21.6 (0.850) 15.2 (0.600) 0.9 (0.035) CV (0.893) 16.6 (0.653) 21.2* (0.834) 0.9 (0.035) 1 1 ±0.5 1 ±0.5 CV43/53/63/73/ (0.437) 5.08 (0.200) CV44/54/64/74/ (0.583) 7.62 (0.300) Note 1. This style is only available in 3 & 4 chip assemblies HO TO ORDER CV 52 5 C 106 M A 3 0 A 2 ize Voltage Dielectric Capacitance Capacitance pecification Finish ead Dia. ead pace ead Code Code Code Code Code Tolerance Code Code Code Code Code (see product section) 5 = 50V A = C0G (2 significant J = ±5% A = Non-customized 3 = Uncoated 0 = tandard A = tandard 2 = 2 Terminal 1 = 100V C = X7R digits + no. K = ±10% 8 = Coated 4 = 4 Terminal 2 = 200V of zeros) M = ±20% (classified as ee Note 1 7 = 500V eg. 105 = 1 µf P = % uninsulated) above 106 = 10 µf 107 = 100 µf Note: ee page 86 for How to Order B9100 parts 29
3 MP Capacitors (CH ) European Preferred s HORIZONTAY MOUNTED 4 TERMINA RADIA PRODUCT Part Number format (CHxxxxxxxxx3xx4) Typical Part Number CH782C106MA30A4 M1 M2 25 (0.984) ±3 (0.118) ead dia (see table) ead Dia 1 CH (0.417) 8.7 (0.342) 8.2 (0.322) 0.7 (0.028) 5.08 (0.200) CH (0.468) 10.7 (0.421) 10.2 (0.400) 0.9 (0.035) 7.62 (0.300) CH (0.649) 13.6 (0.535) 15.2 (0.600) 0.9 (0.035) 7.62 (0.300) CH (0.700) 21.6 (0.850) 15.2 (0.600) 0.9 (0.035) 15.2 (0.600) CH (0.893) 16.6 (0.653) 21.2* (0.834) 0.9 (0.035) 10.2 (0.400) CH (0.555) 38.2 (1.503) 10.2 (0.400) 0.9 (0.035) 27.9 (1.100) CH (0.700) 38.2 (1.503) 15.2 (0.600) 1.0 (0.039) 27.9 (1.100) CH (0.893) 40.6 (1.598) 21.2* (0.834) 1.2 (0.047) 30.5 (1.200) *Tolerance ± 0.8 NOTE: This style is only available in 2, 3 & 4 chip assemblies only 1 ± 0.5 ± 0.5 M1 = M2 ± 0.5 CH42/52/62/72/77/87/ (0.291) CH43/53/63/73/78/88/ (0.437) CH44/54/64/74/79/89/ (0.583) HORIZONTAY MOUNTED DUA-IN-INE PRODUCT Part Number format (CHxxxxxxxxxx0A0) Typical Part Number CH615C106MA30A0 T (0.100) ± 0.05 (0.002) 2.0 (0.079) 13 ± (0.512) 1 (0.039) 1 ± 0.5 ead width 0.5 ead thickness (0.100) 1 = 2 ± 0.5 No. of eads per side CH (0.362) 8.7 (0.342) 8.2 (0.322) 3 CH (0.421) 10.7 (0.421) 10.2 (0.400) 4 CH (0.586) 13.6 (0.535) 14.0 (0.551) 5 CH (0.661) 21.6 (0.850) 15.2 (0.600) 7 CH (0.850) 16.6 (0.653) 20.3* (0.800) 6 CH (0.472) 38.2 (1.503) 10.2 (0.400) 14 CH (0.744) 38.2 (1.503) 15.2 (0.600) 14 CH (0.944) 40.6 (1.598) 20.3* (0.800) 14 CH41/51/61/71/76/81/86/ (0.150) CH42/52/62/72/77/82/87/ (0.291) CH43/53/63/73/78/83/88/ (0.437) CH44/54/64/74/79/84/89/ (0.583) HO TO ORDER CH 52 5 C 106 M A 3 0 A 0 ize Voltage Dielectric Capacitance Capacitance pecification Finish ead Dia. ead pace ead Code Code Code Code Code Tolerance Code Code Code Code Code (see product section) 5 = 50V A = C0G (2 significant J = ±5% A = Non-customized 3 = Uncoated 0 = tandard A = tandard 0 = traight dual 1 = 100V C = X7R digits + no. K = ±10% 8 = Coated in line 2 = 200V of zeros) M = ±20% (classified as 4 = 4 Terminal 7 = 500V eg. 105 = 1 µf P = % uninsulated) 106 = 10 µf 107 = 100 µf Note: ee page 86 for How to Order B9100 parts 30
4 MP Capacitors (CH ) European Preferred s HORIZONTAY MOUNTED EAD MT PRODUCT Part Number format (CHxxxxxxxxxx0A7) Typical Part Number CH411C275KA30A (0.1) ± 0.5 (0.02) ± 0.5 (0.02) 2.54 (0.1) ± 0.5 (0.02) No. of eads per side CH (0.362) 8.7 (0.342) 8.2 (0.322) 3 CH (0.421) 10.7 (0.421) 10.2 (0.400) 4 CH (0.586) 13.6 (0.535) 14.0 (0.551) 5 CH (0.661) 21.6 (0.850) 15.2 (0.600) 7 CH (0.850) 16.6 (0.653) 20.3* (0.800) 6 CH (0.472) 38.2 (1.503) 10.2 (0.400) 14 CH (0.744) 38.2 (1.503) 15.2 (0.600) 14 CH (0.944) 40.6 (1.598) 20.3* (0.800) NOTE: A lead low profile version (CH...0A5) is available with lead height 1.1 (0.043). for single chip assemblies eg. CH415C225MA30A5 ead width 0.5 ead thickness (0.010) 1 = 2 ± 0.5 CH41/51/61/71/76/81/86/ (0.150) CH42/52/62/72/77/82/87/ (0.291) CH43/53/63/73/78/83/88/ (0.437) CH44/54/64/74/79/84/89/ (0.583) HORIZONTAY MOUNTED J EAD MT PRODUCT Part Number format (CHxxxxxxxxxx0A8) Typical Part Number CH411C275KA30A8 2 1 ead width 0.5 ead thickness (0.010) 1 = 2 ± (0.100) ± 0.5 ± 0.5 NOTE: A J lead low profile version (CH...0A3) is available with lead height 1.1 (0.043). for single chip assemblies eg. CH515C475MA30A (0.100) ± 0.5 No. of eads per side CH (0.362) 8.7 (0.342) 8.2 (0.322) 3 CH (0.421) 10.7 (0.421) 10.2 (0.400) 4 CH (0.586) 13.6 (0.535) 14.0 (0.551) 5 CH (0.661) 21.6 (0.850) 15.2 (0.600) 7 CH (0.850) 16.6 (0.653) 20.3* (0.800) 6 CH (0.472) 38.2 (1.503) 10.2 (0.400) 14 CH (0.744) 38.2 (1.503) 15.2 (0.600) 14 CH (0.944) 40.6 (1.598) 20.3* (0.800) 14 CH41/51/61/71/76/81/86/ (0.150) CH42/52/62/72/77/82/87/ (0.291) CH43/53/63/73/78/83/88/ (0.437) CH44/54/64/74/79/84/89/ (0.583) HO TO ORDER CH 52 5 C 106 M A 3 0 A 7 ize Voltage Dielectric Capacitance Capacitance pecification Finish ead Dia. ead pace ead Code Code Code Code Code Tolerance Code Code Code Code Code (see product section) 5 = 50V 1 = 100V A = C0G C = X7R (2 significant digits + no. J = ±5% K = ±10% A = Non-customized 3 = Uncoated 8 = Coated 0 = tandard A = tandard 3 = ow profile J (single chip) 2 = 200V of zeros) M = ±20% (classified as 5 = ow profile 7 = 500V eg. 105 = 1 µf P = % uninsulated) (single chip) 106 = 10 µf 7 = Dual in line 107 = 100 µf 8 = J Dual in line Note: ee page 86 for How to Order B9100 parts 31
5 MP Capacitors (CH/CV ) European Preferred s C0G DIEECTRIC UTRA TABE CERAMIC CH/CV41-44 CH/CV51-54 CH/CV61-64 CH/CV71-74 CH/CV76-79 CH81-84 CH86-89 CH91-94 s s s s s s s s Voltage DC Cap µf NB Figures in cells refer to size within ordering information 32
6 MP Capacitors (CH/CV ) European Preferred s X7R DIEECTRIC TABE CERAMIC CH/CV41-44 CH/CV51-54 CH/CV61-64 CH/CV71-74 CH/CV76-79 CH81-84 CH86-89 CH91-94 s s s s s s s s Voltage DC Cap µf NB Figures in cells refer to size within ordering information 33
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
P O W E R C A P A C I T O R A S S E M B L I E S
AMERICAN TECHNICAL CERAMICS P O W E R C A P A C I T O R A S S E M B L I E S ISO 9001 REGISTERED COMPANY Overview About ATC Power Assemblies ATC standard & custom Power Assemblies are fabricated from PARALLEL
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
Polymer Termination. Mechanical Cracking 2. The reason for polymer termination. What is Polymer Termination? 3
Polymer Termination An alternative termination material specifically designed to absorb greater levels of mechanical stress thereby reducing capacitor failures associated with mechanical cracking Mechanical
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC / Class Y1, 500 V AC
4L Series AC Line Rated Ceramic Disc Capacitors Class X, 76 V AC / Class Y, 5 V AC FEATURES Complies with IEC 6384-4, 4 th edition High reliability Radial leads High capacitance up to nf Singlelayer AC
Types MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
AC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
SIL Resistor Network. Resistors. Electrical. Environmental. L Series. Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant
Resistors SIL Resistor Network Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2) Electrical Standard Resistance
Series AMLDL-Z Up to 1000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Series Up to ma LED Driver Models Single output Model Input Voltage (V) Step Down DC/DC LED driver Operating Temperature range 4ºC to 85ºC
RoHS APPROVAL SHEET. ituner 12V/6.6A SERIES NO. (E17) EA10953A. ( ) Edac Power Electronics (Suzhou) Co., Ltd. 59 No.59, Chang Sheng Road, Sheng Pu,
APPROVAL SHEET CUSTOMER ituner CUSTOMER P/N DESCRIPTION EDAC MODEL 12V/6.6A SERIES NO. (E17) EA10953A DATE 2010-06-22 REVISION 0 APPROVED DESIGN PREPARE RoHS CONCLUSION APPROVED CONDITON CUSTOMER S APP
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC QUICK REFERENCE DATA DESCRIPTION VALUE Ceramic Class 1 2 Ceramic Dielectric U2J U2J Y5S, Y5U Y5S, Y5U Voltage (V AC ) 500 760
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
DISCRETE SEMICONDUCTORS DATA SHEET. BLF244 VHF power MOS transistor
DISCRETE SEMICONDUCTORS DATA SHEET September 1992 FEATURES High power gain Low noise figure Easy power control Good thermal stability Withstands full load mismatch Gold metallization ensures excellent
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type MKT80 FEATURES AEC-Q00 qualified (rev. D) for PCM. mm (for larger available components on request) High temperature capabilities, up to 0 C Capacitance up to 60
Top Microsystems Proprietary Specification P/N: W090015HK-XP 022410RB-082709V.A0 SPECIFICATION
SPECIFICATION High Quality Switching Wallmount Adapter Interchangeable AC Plugs 90-264VAC Input 13.5W 9VDC 1.5A Output P/N: W090015HK-XP ** Specification Approval** This specification (total 11 pages including
High-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator Description: The NTE923 and NTE923D are voltage regulators designed primarily for series regulator applications. By themselves, these devices
CA723, CA723C. Voltage Regulators Adjustable from 2V to 37V at Output Currents Up to 150mA without External Pass Transistors. Features.
CA73, CA73C Data Sheet April 1999 File Number 788. Voltage Regulators Adjustable from V to 37V at Output Currents Up to 1mA without External Pass Transistors The CA73 and CA73C are silicon monolithic integrated
SELECTION GUIDE. Nominal Input
www.murata-ps.com NKE Series FEATURES RoHS Compliant Sub-Miniature SIP & DIP Styles 3kVDC Isolation UL Recognised Wide Temperature performance at full 1 Watt load, 40 C to 85 C Increased Power Density
High-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
Powering Integrated Circuits (ICs), and managing ripple voltage as it relates
Ripple Voltage & ESR Powering Integrated Circuits (ICs), and managing ripple voltage as it relates to ESR of capacitors Low voltage ICs require supply voltage (Vcc) to have reduced levels of ripple voltage
SUCCESS EPCOS Capacitors
SUCCESS EPCOS Inc. Capacitors Group April, 2012 EV / HV / E-Mobility Battery charger system & Inverter On Board and Off Board Assembly Trend: Wireless Charging DC/DC Converter Filtering DC Link E-Mobility
SECTION 13. Multipliers. Outline of Multiplier Design Process:
SECTION 13 Multipliers VMI manufactures many high voltage multipliers, most of which are custom designed for specific requirements. The following information provides general information and basic guidance
Capacitance Cap. Tol. Suffix construction. Rated voltage
Metallized Polypropylene Film Capacitors Type:ECWFE Plastic Film Capacitors Non-inductive construction using metalized Polypropylene film with flame retardant plastic case. Features Small size Excellent
Application Note TMA Series
1W, SIP, Single & Dual Output DC/DC Converters Features SIP Package with Industry Standard Pinout Package Dimension: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 5V&12V Models 19.5 x 10.2 x 7.1 mm (0.77 x
FP2 Relay. The Best Relaytion
The Best Relaytion 2 pole telecom / signal relay Through Hole Type (THT) Polarized. Relay types: non-latching with1 coil latching with 1 coil latching with 2 coils Features Telecom / signal relay (dry
PowerAmp Design. PowerAmp Design PAD135 COMPACT HIGH VOLATGE OP AMP
PowerAmp Design COMPACT HIGH VOLTAGE OP AMP Rev G KEY FEATURES LOW COST SMALL SIZE 40mm SQUARE HIGH VOLTAGE 200 VOLTS HIGH OUTPUT CURRENT 10A PEAK 40 WATT DISSIPATION CAPABILITY 200V/µS SLEW RATE APPLICATIONS
Knob Potentiometer FEATURES. P16NP P16NM Panel Cutout. Thickness nut 2 mm washer 1.5 mm. Panel sealing ring 12 wrench Thread M10 x 0.75 10.2 9.
Knob Potentiometer P6, PA6 FEATURES Test according to CECC 4000 or IEC 60393- P6 - Version for professional and industrial applications (cermet) W at 40 C PA6 - Version for professional audio applications
DATA SHEET CHIP RESISTORS RT Series 1%; 0.5%; 0.25%; 0.1%
DATA SHEET CHIP RESISTORS Series 1%; 0.5%; 0.25%; 0.1% Product specification Supersedes Date of Sep. 30, 2003 ynsc004 ynsc015 ynsc002 ynsc007 2 SCOPE This specification describes series chip resistors
Knob Potentiometer with Switch
Knob Potentiometer with Switch The is a revolutionary concept in panel mounted potentiometers. This unique design consists of a knob driving and incorporating a cermet potentiometer. Only the mounting
Aluminum Capacitors Solid Axial
SAL-A End of Life. Last Available Purchase Date is -December- Radial higher CV/volume Fig. QUICK REFERENCE DATA DESCRIPTION VALUE Maximum case size (Ø D x L in mm) 6.7 x. to.9 x. Rated capacitance range
INTEGRATED CIRCUITS. For a complete data sheet, please also download:
INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications The IC06 74HC/HCT/HCU/HCMOS Logic Package Information The IC06 74HC/HCT/HCU/HCMOS
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
X and Y Capacitors. Copyright 2008 KEMET
X and Y Capacitors X Capacitors Two Major Types: X2 and X1 X2 capacitors Agency tested with 2,500 volt surge test. Satisfies 99% of the applications. X1 capacitors Agency tested with 4,000 volt surge test.
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
Capacitor Self-Resonance
Capacitor Self-Resonance By: Dr. Mike Blewett University of Surrey United Kingdom Objective This Experiment will demonstrate some of the limitations of capacitors when used in Radio Frequency circuits.
SOLUTION FOR INCREASING CAPACITANCE DEMAND HIGH CV TANTALUM CAPACITORS
SOLUTION FOR INCREASING CAPACITANCE DEMAND HIGH CV TANTALUM CAPACITORS T. Zednicek, AVX Czech Republic s.r.o., Dvorakova 328, 563 1 Lanskroun, Czech Republic Phone: +42 467 558 126 Fax: +42 467 558 128
Type MLP 85 C Flatpack, Ultra Long Life, Aluminum Electrolytic Very Low Profile
The MLP s high-energy storage and box-shape make it perfect for voltage holdup or filtering in military SEM-E modules, telecom circuit packs and computer cards. The MLP delivers up to 20 joules of energy
handbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing Extended voltage and capacitance range SMD-version, fully moulded, insulated Flexible terminals, reflow and wave solderable
DISCRETE SEMICONDUCTORS DATA SHEET M3D060. BLF177 HF/VHF power MOS transistor. Product specification Supersedes data of 1998 Jul 02.
DISCRETE SEMICONDUCTORS DATA SHEET M3D6 Supersedes data of 1998 Jul 2 23 Jul 21 FEATURES High power gain Low intermodulation distortion Easy power control Good thermal stability Withstands full load mismatch.
4 A CAPACITY, THE VARIETY OF CONTACT ARRANGEMENTS FEATURES
4 A CAPACITY, THE VARIETY OF CONTACT ARRANEMENTS S RELAYS FEATURES 28. 1.12 12..472 1.4.49 The variety of contact arrangements 2 Form A 2 Form B, 3 Form A 1 Form B, 4 Form A Latching types available High
Chip Monolithic Ceramic Capacitors
This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it s specifications are subject to change or our products in it may be discontinued without advance notice.
Power Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
Pulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
WCAP-CSGP Ceramic Capacitors
A Dimensions: [mm] B Recommended land pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1±0.2 Vrms, 1 khz ±10% C 15000 pf ± 10% Rated voltage Dissipation factor
.093 [2.36] Commercial Pin and Socket Connectors
![.093 [2.36] Commercial Pin and Socket Connectors](/thumbs/40/21560042.jpg ".093 [2.36] Commercial Pin and Socket Connectors")
Product Facts Polarized Cavity identification Low contact-mating force Dual locking lances Detent and positive locking Contacts available in brass and phosphor bronze with tin and gold plating Panel mounting
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 10 ASC_WR_V23 APR.- 2015
TDA2040. 20W Hi-Fi AUDIO POWER AMPLIFIER
20W Hi-Fi AUDIO POWER AMPLIFIER DESCRIPTION The TDA2040 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB amplifier. Typically it provides 22W output power
AZ420 MINIATURE GENERAL PURPOSE RELAY
MINIATURE GENERAL PURPOSE RELAY FEATURES Rugged construction for high reliability Life expectancy greater than 0 million operations DC coils to 11 V Power consumption as low as 2 mw per pole available
TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
LM138 LM338 5-Amp Adjustable Regulators
LM138 LM338 5-Amp Adjustable Regulators General Description The LM138 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 5A over a 1 2V to 32V output range
Standard Thick Film Chip Resistors
Standard Thick Film Chip Resistors FEATURES Stability R/R = 1 % for 00 h at 70 C 2 mm pitch packaging option for size Pure tin solder contacts on Ni barrier layer provides compatibility with lead (Pb)-free
NOT RECOMMENDED FOR NEW DESIGNS
28 Volt NOT RECOMMENDED FOR NEW DESIGNS Features Attenuation 0 db from 110 khz to 0 MHz Operating temperature - to +8 C Nominal 28 V input, 0 V to 0 V operation 1.7 to A throughput current Transient suppression
Type MLS 125 C Flatpack, Ultra Long Life, Aluminum Electrolytic Now Available with High Vibration and High Reliability Options
Now Encased in rugged stainless steel, the MLS is perfect for high reliability military systems and applications operating above 85 C. For our highest performing 25 C Flatpacks, choose type HVMLS available
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
Type EDL, Electric Double Layer Supercapacitors Ultra High Capacitance, Small Case Size Options
Ultra High Capacitance, Small Case Size Options Type EDL electric double layer supercapacitors offer extremely high capacitance values (farads) in a variety of packaging options that will satisfy, low
Yet More On Decoupling, Part 1: The Regulator s Interaction with capacitors Kendall Castor-Perry
Page 1 of 6 Yet More On Decoupling, Part 1: The Regulator s Interaction with capacitors Kendall Castor-Perry In Know the sometimes-surprising interactions in modelling a capacitor-bypass network (http://www.planetanalog.com/showarticle.jhtml?articleid=202402836,
Power Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series Non inductive Easy
QUICK REFERENCE DATA. Pilkor components FEATURES APPLICATIONS
MKP RADIAL POTTED CAPACITORS Pitch 10.0/15.0/22.5/27.5 mm QUICK REFERENCE DATA Capacitance range (E6 series) * 0.01μF to 3.3μF Capacitance tolerance ±10 %, ±20 % Rated (AC) voltage 50 to 60 Hz 275 V ~
EE301 Lesson 14 Reading: 10.1-10.4, 10.11-10.12, 11.1-11.4 and 11.11-11.13
CAPACITORS AND INDUCTORS Learning Objectives EE301 Lesson 14 a. Define capacitance and state its symbol and unit of measurement. b. Predict the capacitance of a parallel plate capacitor. c. Analyze how
ATC 800 B Series NPO Ceramic, High RF Power Ultra-Low ESR Multilayer Capacitors
800 Series NPO Ceramic, High RF Power Ultra-ow ESR Multilayer Capacitors Case Size (" x ") Rugged, reliable NPO dielectric Case optimized for highest self resonant frequency s 800 Series offers superb
Insulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
Baseband delay line QUICK REFERENCE DATA
FEATURES Two comb filters, using the switched-capacitor technique, for one line delay time (64 µs) Adjustment-free application No crosstalk between SECAM colour carriers (diaphoty) Handles negative or
CMR Series Isolated 0.75W Single and Dual Output Isolated DC/DC Converters
www.murata-ps.com CMR Series SELECTION GUIDE FEATURES Single or Dual Isolated Outputs 1kVDC or 3kVDC options Wide temperature performance at full 0.75W load -40 C to 85C Industry Standard Pinouts 5V, 12V
DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip
Trip circuit supervision relay. Type RXTCS
Trip circuit supervision relay Type RXTCS ABB a global technology leader ABB is a global leader in Power and Automation technologies that enable utility and industry customers to improve performance while
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to
50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
ATC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors
AC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors Features: Lowest ESR in Class Highest Working Voltage in class 250V Standard EIA Size: 0603 Laser Marking (Optional) RoHS Compliant High
Circulating Current Relay. Type IRXm
Circulating Current Relay Type IRXm ABB a global technology leader ABB is a global leader in Power and Automation technologies that enable utility and industry customers to improve performance while lowering
O WA-120U series IP67. 120W Single Output Switching Power Supply. Features. Aplications
Features UniversalACinput/Fulrange Built-inactivePFCfunction Higheficiencyupto91% Protections:Shortcircuit/Overcurent/ Overvoltage/Overtemperature Fanlesdesign,colingbyfreairconvection Colingbyfreairconvection
High Ohmic (up to 68 MΩ)/ High Voltage (up to 10 kv) Resistors
High Ohmic (up to 68 MΩ)/ A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps.
Metallized Polypropylene Film Capacitors DC-Link Capacitor
Metallized Polypropylene Film Capacitors DC-Link Capacitor FEATURES Slim line, low building height Very long useful life time: Up to 100 000 h at U NDC and 70 C High ripple current capability, low ESR,
General information. Please refer to our Internet address (http://www.kemet.com) for updated information on KEMET products, services and news.
DC Film Capacitors Please refer to our Internet address (http://www.kemet.com) for updated information on KEMET products, services and news. Contents Pitch Rated Voltage Capacitance Page mm Vdc range range
AC/DC Power Modules C B. TML Series, 20 & 40 Watt. Features. 20 Watt Models
TML Series, 0 & 0 Watt Features C B Scheme LVD UL 090- Encapsulated power supplies with increased power density Replaces TML and TML 0 series PCB mount or chassis mount with screw terminals Single, dual
DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/122/124/162/164/248/324/158/358 TC: 122/124/164
Product specification December 11, 2015 V.2 0 DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/2/4/162/164/248/324/158/358 TC: 2/4/164 RoHS compliant Product specification 2 SCOPE This specification
INTERNATIONAL ATOMIC ENERGY AGENCY INSTRUMENTATION UNIT SMD (SURFACE MOUNTED DEVICES) REPAIR S. WIERZBINSKI FEBRUARY 1999
(SURFACE MOUNTED DEVICES) REPAIR S. WIERZBINSKI FEBRUARY 1999 (SURFACE MOUNTED DEVICES) REPAIR 1 TABLE OF CONTENTS PAGE 1. INTRODUCTION 3 2. ADVANTAGES 4 3. LIMITATIONS 4 4. DIALECT 5 5. SIZES AND DIMENSIONS
MUHAMMAD ABDULLAH AL-AZZAZ COMPANY LIMITED P.O. BOX 31172 AL-KHOBAR 31952 KINGDOM OF SAUDI ARABIA
This is to signify that MUHAMMAD ABDULLAH AL-AZZAZ COMPANY LIMITED P.O. BOX 31172 AL-KHOBAR 31952 KINGDOM OF SAUDI ARABIA Calibration Laboratory CL-151 has met the requirements of the IAS Accreditation
TEP 200WIR Series, 180 240 Watt
TEP 200WIR Series, 180 240 Watt Features Chassis mount with screw terminal block Including EMI filter to meet EN 55022, class A Ultra wide 4:1 input voltage ranges 8.5 36, 16.5 75, 43 160 VDC EN 50155
RFI/EMI TELEPHONE FILTERS
RFI/EMI TELEPHONE FILTERS Description These filter ranges are specifically designed to meet the stringent requirements for telephone circuits. The high electrical symmetry between lines means they are
PIN CONFIGURATION FEATURES ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS. D, F, N Packages
DESCRIPTION The µa71 is a high performance operational amplifier with high open-loop gain, internal compensation, high common mode range and exceptional temperature stability. The µa71 is short-circuit-protected
Thermal Resistance, Power Dissipation and Current Rating for Ceramic and Porcelain Multilayer Capacitors
Thermal Resistance, Power Dissipation and Current Rating for Ceramic and Porcelain Multilayer Capacitors by F. M. Schaubauer and R. Blumkin American Technical Ceramics Reprinted from RF Design Magazine,
Power chip resistor size 2512 PRC221 5%; 2% FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability.
FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability. APPLICATIONS Power supplies Printers Computers Battery chargers Automotive Converters CD-ROM. QUICK
RC NETWORKS SALES GUIDE
SALES GUIDE INTRODUCTION TO Recent developments in electronic equipment have shown the following trends: Increasing demands for numerical control machines, robotics and technically advanced appliances
Interference Suppression Film Capacitors MKP Radial Potted Type
Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 7.5 mm to 27.5 mm lead pitch Supplied loose in box, taped on reel Material categorization: For definitions of compliance please
SuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal
SuperTan Extended () Capacitors, Wet Tantalum Capacitors with Hermetic Seal FEATURES SuperTan Extended () represents a major breakthrough in wet tantalum capacitor Available technology. Its unique cathode
Precision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
unit : mm With heat sink (see Pd Ta characteristics)
Ordering number: EN1321E Monolithic Linear IC LA4261 3.5 W 2-Channel AF Power Amplifier for Home Stereos and Music Centers Features. Minimum number of external parts required (No input capacitor, bootstrap
Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability
Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability 048 RML 48 RUS lower longer life 36 RVI miniaturize 50 RMI high vibration FEATURES Very long useful life: 7000
LM117 LM317A LM317 3-Terminal Adjustable Regulator
LM117 LM317A LM317 3-Terminal Adjustable Regulator General Description The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1 5A over a 1 2V to 37V
The Important Points of Multi-layer Ceramic Capacitor Used in Buck Converter circuit
Switching Regulator Series The Important Points of Multi-layer Ceramic Capacitor Used in Buck Converter circuit No.1327EAY7 Multi-layer Ceramic Capacitor (MLCC) with large-capacitance can be used as smoothing-capacitor
film capacitors QUICK REFERENCE DATA Pilkor components FEATURES APPLICATIONS 10 and 15mm 22.5 and 27.5mm
MKP RADIAL POTTED CAPACITORS Pitch 10.0/15.0/22.5/27.5/37.5mm 10 and 15mm 22.5 and 27.5mm QUICK REFERENCE DATA Capacitance range (E6 series) * Capacitance tolerance Rated (AC) voltage 50 to 60 Hz Climatic
Reed V23100-V4 Relay. AXICOM Telecom-, Signal and RF Relays. AXICOM Telecom-, Signal and RF Relays. Reed V23100-V4 Relay
AXICOM AXICOM 108-98011 Nov. 07 Rev. C ECOC: JM10 Disclaimer While Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this datasheet, Tyco Electronics does not
7-41 POWER FACTOR CORRECTION
POWER FTOR CORRECTION INTRODUCTION Modern electronic equipment can create noise that will cause problems with other equipment on the same supply system. To reduce system disturbances it is therefore essential
EMERGENCY EGRESS LIGHTING POWER SUPPLY PART NO. 5925-6 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST
EMERGENCY EGRESS LIGHTING POWER SUPPLY PART NO. WITH ILLUSTRATED PARTS LIST Initial Issue: June 16, 1995 33-51-80Page 1 May 20/2010 RECORD OF REVISIONS REV. NO. ISSUE DATE A 01-26-96 B 09-21-99 C 10-26-09
The Best Relaytion. Reed Relays. 108-98011 Rev. B EC-JM00-0009-03 ECOC: JM10 1. Aug. 04
The Best Relaytion Reed Relays 108-98011 Rev. B EC-JM00-0009-03 ECOC: JM10 1. Aug. 04 1 and 2 pole relays non-polarized, non-latching Features Direct coil control with TTL-signals possible Highly reliable
EPL225 Series. 225 Watts. www.xppower.com. AC-DC Power Supplies. Models & Ratings. Summary
225 Watts 50 W Convection/ 225 W Forced-cooled Ratings 2 by 4 Footprint Low.26 Profile 2 V Fan Output High Efficiency, up to 95% ITE & Medical pprovals High Power Density Less than 0.5 W No Load Input
Operating Manual UWAPS-TINY Series
Operating Manual UWAPS-TINY Series Powecon Oy WWW.POWECON.FI 1/9 Table of content 1 Warranty...3 2 Safety information...3 3 Abbreviations and terminology...3 4 List of appendices...4 5 Introduction...4