IXP200 LCD Keypad Controller

Transcription

1 IXP200 Controller IXP200 LCD Keypad Controller Overview Introduction Key Features The IXP200 LCD Keypad Controller is a fully featured Controller that forms part of the ImproX family of access control equipment. The IXP200 Controllers applications include, access control, alarm control, time and attendance monitoring and job costing. The Controller has a 20-key Keypad and a 16-character by 4-line alphanumeric Liquid Crystal Display (LCD). Both the Keypad and the LCD include back-lighting. The back-lighting for the Keypad and the LCD work in conjunction and are switched on or off via the Communications Protocol. The Controller offers 4 Bus Activity LED Indicators for the installer and 1 Power-on Indicator. The Bus Activity LED Indicators indicate incoming and outgoing RS232 and RS485 Data. The Controller is capable of communicating with other ImproX units via an RS485 Terminal Bus Port and with a PC via an RS232 or RS485 Host Bus Port. Tag read/write capability: Slim Tags (read only), Omega Tags (read only), WriTag 128 (read/write) and WriTag 2048 (read/write). LEDs indicate transmit and receive line activity for diagnostics. A real-time clock. Remote Firmware download capability. An RS232 or RS485 Host Bus Port for connection to the system PC. An RS485 Terminal Bus Port for connection of other ImproX Terminal devices. 1

2 An RS232 Serial Peripheral Port for connection of compatible Barcode Readers, Magstripe Readers, or Keypads. Operation from power inputs in the range 10 V to 30 V DC. A 20-key Keypad with back-lighting. A 16-character by 4-line alphanumeric Liquid Crystal Display (LCD) (English, Katakana) with back-lighting. Tag Read/Write Ranges The range that the Controller can read from or write to a Tag is dependent on the type of Tag and material on which the Controller is installed. Typical ranges are shown in Table 1. Typical Range (Minimum) Tag Type (Controller installed on non-metallic surface) (mm) (in) ISO Credit Card Tag (Slim) ImproX Credit Card Tag ImproX Round Tag ISO Credit Card WriTag ISO Credit Card WriTag NOTE: Installing the Controller on a metallic surface will reduce the Tag read/write range slightly. Table 1: Typical Read/Write Ranges Approvals CE Approved. FCC Approved. 2

3 Specifications Physical Dimensions Length : 204 mm (8.03 in). Width : 121 mm (4.76 in). Height : 45 mm (1.77 in). Approximate Weight : 510 g (17.97 oz). Cabinet Material : ABS Plastic. Colour : Dark Grey. Environmental Temperature Operating : -15 o C to +60 o C (+5 o F to +140 o F). Storage : -40 o C to +80 o C (-40 o F to +176 o F). Humidity Range : 0 to 95% relative humidity at +40 o C (+104 o F) noncondensing. Approvals (Test Information) EMC : EN 55022: Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipment. EN 55024: Immunity Characteristics, Limits and Methods of Measurement. Electrostatic Discharge : IEC : Electromagnetic Compatibility (EMC). Part 4: Testing and Measurement Techniques. Section 2: Electrostatic Discharge Immunity Test. Basic EMC Publication. Radiated Susceptibility : IEC : Electromagnetic Compatibility (EMC). Part 4: Testing and Measurement Techniques. Section 3: Radiated, Radio-Frequency, Electromagnetic Field Immunity Test. Electrical Fast Transients : IEC : Electromagnetic Compatibility (EMC). Part 4: Testing and Measurement Techniques. Section 4: Electrical Fast Transients / Bursts. Basic EMC Publication. Surge Immunity : IEC : Surge Immunity. Conducted Susceptibility : IEC : Conducted Susceptibility. Power Frequency Magnetic Field : IEC : Electromagnetic Compatibility (EMC). Part 4: Testing and Measurement Techniques. Section 8: Frequency Magnetic Field Immunity Test. Dust and Splash Resistance : Designed to work in an indoor (dry) environment similar to IP40. The Controller is, therefore, NOT sealed against water. Drop Endurance : 2 m (6.56 ft) drop (in packaging). 3

4 Electrical Power Requirements Input Voltage : 10 V DC to 30 V DC. Power Requirements Current (ma) Power (W) Supply Voltage 10 V DC Relays all OFF : Supply Voltage 10 V DC Relays all ON : Supply Voltage 30 V DC Relays all OFF : Supply Voltage 30 V DC Relays all ON : Permissible Input Supply Ripple Voltage (Max) : 1 V PP at 50 Hz. Power Input Protection : Reverse polarity, over-voltage and over-current protection are provided on the Controller. Terminal Bus Port (Port 1) Electrical Interface : RS485, ASCII with 16-bit CRC checking. Baud Rates : 1 200, 2 400, 4 800, 9 600, , , , and selectable via the Protocol. Data Format : 8 data bits, no parity, 1 stop bit. Communications Protocol : ImproX Secure Communications Protocol. Line Termination : Provision is made for line termination. Default Mode : Transmit Mode. Host Bus Port (Port 2) Electrical Interface : RS232 (full duplex, no flow control) or RS485, ASCII with 16-bit CRC checking, selectable via the Protocol. Baud Rates : 1 200, 2 400, 4 800, 9 600, , , and selectable via the Communications Protocol. Data Format : 8 data bits, no parity, 1 stop bit. Communications Protocol : ImproX Secure Communications Protocol. Line Termination (RS485) : Provision is made for line termination. Default Mode (RS485) : Receive Mode. Unit Status : Slave. Serial Peripheral Port (Port 3) Electrical Interface : RS232 (full duplex, RTS and CTS flow control available). Baud Rates : 1 200, 2 400, 4 800, 9 600, , , , and selectable via the Communications Protocol. Data Format : 8 data bits, no parity, 1 stop bit. Interface Protocol : Determined by the peripheral device used. Relays Relay Output : 2 x Relays, each with NO, COM and NC contacts. Contact Ratings : 10 A at 28 V DC, 5 A at 220 V AC. 4

5 Digital Inputs Input Type : 4 x Dry Contact Inputs. Protection Range : +15 V and -15 V continuous. Anti-tamper Protection : An internal infra-red beam detects when the Front Cover is removed from the Controller. This event detection is reported by the Controller via the Protocol. Memory RAM (Non-volatile) : 512 KBytes. Flash ROM : 128 KBytes. Battery Backup (for RAM) Factory Default Settings Battery Type : 1 x 3.6 V, size ½ AA. Battery Life : 5 Years (with power OFF). Test Modes Power-on Self-test : RAM, Flash-ROM, Tag Read/Write, RTC and stuck keys. Baud Rate Terminal Bus Port : Host Bus Port : Back-lighting LCD and Keypad : On. Contrast (LCD) : Level 3. Host Port Mode : RS232. Buzzer Tone : 25. Volume : Level 4 (maximum). 5

6 Operator or Installer Interfaces Liquid Crystal Display (LCD) Characters : 16 Characters by 4 lines. Character Sets : English, Katakana. Contrast : Adjustable in 8 discrete steps via the Communications Protocol. Back-lighting : Turned on and off via the Communications Protocol. Keypad Buzzer Buttons : 20 Alphanumeric and function keys. Back-lighting : Turned on and off via the Communications Protocol. NOTE: The LCD and Keypad back-lighting operate in conjunction. Volume and Tone : 5-Step adjustable volume, 36 different tones. Selectable via the Communications Protocol. LED Indicators Power-on Indicator : Red LED (internally visible). Incoming RS485 Data : Flashing Green LED (internally visible). Outgoing RS485 Data : Flashing Red LED (internally visible). Incoming RS232 Data : Flashing Green LED (internally visible). Outgoing RS232 Data : Flashing Red LED (internally visible). Status Indicator : Bi-colour Red or Green LED (externally visible), function programmable via the Communications Protocol. 6

7 Installation Information Accessories Find the following when unpacking the IXP200 Controller: General An IXP200 LCD Keypad Controller housed in a Dark Grey ABS Plastic Cabinet. The Cabinet will consist of a Front and Back Cover secured with a Thread Cutter Screw (M3 x 8 mm). A 3 m (9.84 ft) flat, 4-core RS232 Cable, with a 9-way, D-type female connector at one end. A 3.6 V, >950 mah, ½ AA Cylindrical Lithium Battery. Four Wood Screws (3.5 mm x 25 mm). Four Wall Plugs (7 mm). An extra Fixed Address Label. Remember the following when installing your IXP200 Controller: Communications Distance The RS485 communications distance between the IXP200 Controller and the LAST ImproX Unit in a cable run, MUST NOT exceed 1 km (1 090 yd). Achieve this by using good quality screened, 2-pair, twisted pair cable, EARTHED on one side. The maximum cable distance between the IXP200 Controller and the PC (or peripheral device) is 25 m (27.34 yd). Achieve this by using good quality screened, 4-core cable, with a cross sectional area not less than 0.2 mm 2 ( in 2 ). Termination Resistors for RS485 Bus Communications Long transmission lines or multiple star connections, may cause communication problems. Placing the Terminating Resistor Jumper Link in the LAST UNIT AT THE END OF THE CABLE RUN should solve the problem (depending on the bus). 7

8 EARTH Connection Connect the IXP200 Controller to a good EARTH point. Using either of the RS485 Ports, connect the EARTH Lead to the ETH Terminal. Mains EARTH can be used, but electrical noise may exist. The EARTH Lead to the IXP200 Controller should have a minimum cross-sectional area of 1 mm 2 (0.001 in 2 ) and can be either solid or stranded. Installing the Battery First Time Use CAUTION: Insert the Battery into the Battery Holder BEFORE powering up the IXP200 Controller. The Battery Holder is located in the middle right-hand side of the IXP200 Controllers Printed Circuit Board (PCB), directly below the Bus Activity LED Indicators. Insert the 3.6 V Lithium Battery into the Battery Holder, with the "+" Terminal facing AWAY from the Terminal Blocks. Replacement CAUTION: DO NOT disconnect Power from the IXP200 Controller during this operation. Disconnecting the Power could result in the RAM loosing data. Mounting the Controller 1. With the Controller powered up, remove the Controllers Front Cover. DO NOT disconnect the Ribbon Cable Connectors. 2. Remove the Battery from the Battery Holder. 3. Insert the new 3.6 V Lithium Battery into the Battery Holder, with the "+" Terminal facing AWAY from the Terminal Blocks. 4. Attach the Controllers Front Cover. Select the mounting position of the IXP200 Controller, considering accessibility, routing of wires and visibility of the externally visible LED. Secure the Controller to the mounting surface, using four suitable screws and wall plugs (supplied), nuts and bolts, rivets or double-sided adhesive tape. 8

9 Electrical Connections Connecting the IXP200 Controller Figure 1: Typical IXP200 Controller Electrical Connections 9

10 Power-on Self-test The Power-on Self-test tests the RAM, Flash-ROM checksums, RTC, read/write circuitry and stuck keys. The results of the Self-test are made available as diagnostic information via the Protocol to the associated Controller or PC. If any parameter in the Self-test fails, the Controller emits a continuous beep for 2 seconds. When the Controller passes the Self-test, the Controller emits two short beeps of 200 ms duration, separated by a 200 ms inter-beep pause. Fixed Address Label Once the IXP200 Controller is installed attach the additional loose Fixed Address Label (packaged with the Controller) in position on the Unit Location Chart. When the system installation is complete and all the units are represented on the Unit Location Chart by their Fixed Address Labels, file the document for future reference. Guarantee or Warranty This product conforms to our Guarantee or Warranty details placed on our Web Site, to read further please go to Ordering Information Order the IXP200 Controller using the following Impro part number: XIC GB-XX. This manual is applicable to the IXP200 LCD Keypad Controller, XIC GB-02. (The last two digits of the Impro stock code indicate the issue status of the product). IXP200 Controller\Product Specification Catalogue\LATEST XIC GB-01 Issue 02 June 2005 ISSUE\IXP200C-psc-en-02.doc 10