MOULDING INSTALLATION INSTRUCTIONS Vinyl DeLuxe
|
|
- Prudence Simpson
- 7 years ago
- Views:
Transcription
1 MOULDING INSTALLATION INSTRUCTIONS Vinyl DeLuxe
2 STAIRNOSE MOULDING Stairnose Moulding Installation on flooring with an overall thickness of up to 19 mm (0.75 ). Stair Riser Release Paper Stairnose Surface Roughened up with Sanding Sponge or Sandpaper Install the riser flush to the stair. Clean flooring and moulding with a damp cloth (water only) to remove all dust and residue. Let dry before applying adhesive. Turn Stairnose over and roughen the inside surface of the Stairnose to increase bond by means of 60 grit sandpaper, sanding sponge, or a metal brush. Then, gently peel the release paper all the way off the adhesive tape. The purpose of the double-sided tape is to secure the moulding firmly in place until the premium polyurethane construction adhesive totally cures. Caulk Gun Adhesive Next, apply a generous bead of a Premium Polyurethane Construction Adhesive along the entire inside corner. Be sure to overlap the tape with the adhesive Underside of moulding generously covered with adhesive Bottom of Stairnose Stair Riser Step 4 Touch the bottom of moulding to the stair riser and carefully roll the Stairnose in place. Make any final adjustments before you push the moulding all the way down. Once it s in the final position, press down firmly with your hands and make your way down the entire Stairnose. It may take 2 or 3 passes to set it firmly in place. Adhesive Stair Riser Step 5 For Low Traffic, let the adhesive cure for at least 1 hour before walking on it. For Heavy Traffic, wait 24 to 48 hours. NOTE: Complete cure takes 48 hours. 1 of 2
3 STAIRNOSE MOULDING Stairnose Moulding Installation on flooring with an overall thickness of up to 19 mm (0.75 ). 2 3/ 32 29/ 32 Lock-Down Install (e.g. Stair Treads) Used where floating of the floor is not required, as with Stair Tread or Glued-Down/Nailed-Down floors. This can be used on floating floors where expansion and contraction will occur on the opposite side of the flooring plane. VersaEdge Stairnose Applications Floating Install Laminate / Vinyl / Hardwood / Engineered Wood Laminate / Engineered Wood (Remove Backing to Apply) (3/32 to 3/4 ) DO NOT REMOVE BACKING! Stair Riser Glue Detail Piece of Nailed & Glued Down Vinyl/LVT Alternative Flush Floor Planks Must Be Glued Down! DO NOT REMOVE BACKING! Vinyl/LVT (Remove Backing to Apply) 2 of 2
4 SlimTrim as a REDUCER Use transition track for up to 4 mm floors. Up to 4 mm Floors 3/8 *If the flooring manufacturer suggests/permits the use of underlayments, you may need to shim the track to accomodate the increase in overall thickness Install the flooring plank*. Then place the transition track 3/8 from the floor and screw it to the sub-floor using 4 x 3/4 screws. Rubber Mallet Transition track This end of the Transition MUST be placed on the lower of the two surfaces. Line the transition moulding up with the transition track and fit one end into the moulding. Using a rubber mallet, tap the moulding until it engages with the track. Use your hand to guide the moulding into the track as you work your way down, tapping it in, similar to how you would close a plastic zip bag. transition all the way into the track. You can use a little more force once you are sure it is properly engaged in the track. Use transition and transition shim for 5-6 mm floors. Use the same moulding & track, just add Shim. 5-6 mm Floors 3/8 Shim Install the flooring plank. Then place the transition and shim 3/8 from the floor and screw them to the sub-floor using 4x5/8 screws. Rubber Mallet Transition track This end of the Transition MUST be placed on the lower of the two surfaces. Line the transition moulding up with the transition track and fit one end into the moulding. Using a rubber mallet, tap the moulding until it engages with the track. Use your hand to guide the moulding into the track as you work your way down, tapping it in, similar to how you would close a plastic zip bag. Transition all the way into the track. You can use a little more force once you are sure it is properly engaged in the track. 1 of 8
5 Use transition track for up to 3 mm floors. Up to 3 mm Floors *If the flooring manufacturer suggests/permits the use of underlayments, you may need to shim the track to accomodate the increase in overall thickness Install the flooring planks* by leaving a inch (25mm) gap for the installation of the Transition. Center the TransitionTrack between the two laminate floors and screw it to the sub floor by using 4x3/4 screws. Rubber Mallet Transition track Line the transition moulding up with the transition track and fit one end into the moulding. Using a rubber mallet, tap the moulding until it engages with the track. Use your hand to guide the moulding into the track as you work your way down, tapping it in, similar to how you would close a plastic zip bag. transition all the way into the track. You can use a little more force once you are sure it is properly engaged in the track. Use transition and transition shim for 4-6 mm floors. Use the same moulding & track, just add Transition Shim. 4-6 mm Floors Install the flooring planks by leaving a inch (25mm) gap for the installation of the Transition. Center the transition track and shim between the two laminate floors and screw them to the sub floor by using 4x5/8 screws. Rubber Mallet Shim Transition track Line the transition moulding up with the transition track and fit one end into the moulding. Using a rubber mallet, tap the moulding until it engages with the track. Use your hand to guide the moulding into the track as you work your way down, tapping it in, similar to how you would close a plastic zip bag. transition track all the way into the track. You can use a little more force once you are sure it is properly engaged in the track. 2 of 8
6 Transition Moulding Use Transition track Track (Metal for Track) up to for 3 up mm to floors. 3 mm floors. NOTE: Carpet Tap Down trim must be no less than 1/8 from top of track. Use shim as guide, then remove it. 3/4 Carpet Tap Down Trim Rubber Mallet Up to 3 mm Floors *If the flooring manufacturer suggests/permits the use of underlayments, you may need to shim the track to accomodate the increase in overall thickness Install the flooring plank* and carpet (using a carpet tap down trim) by leaving a inch (25mm) gap for the installation of the transition track. Position the track 3/4 from where the of the Tap Down trim meets the carpet and screw it to the sub floor by using 4x5/8 screws. The carpet tap down trim must be no less than 1/8 from top of track. Use shim to make track and tap down trim even, then remove shim. Line the transition up with the track and fit one end into the moulding. Using a rubber mallet, tap the moulding until it engages with the track. Use your hand to guide the moulding into the track as you work your way down, tapping it in, similar to how you would close a plastic zip bag. Transition all the way into the track. You can use a little more force once you are sure it is properly engaged in the track. Use Transition and Transition Shim for 3-6 mm floors. Use the same moulding & track, just add Transition Shim. 3-6 mm Floors NOTE: Carpet Tap Down trim must be even with the top of the track. 3/4 Carpet Tap Down Trim Rubber Mallet Install the flooring plank and carpet (using a carpet tap down trim) by leaving a inch (25mm) gap for the installation of the transition. Position the track 3/4 from where the of the Tap Down trim meets the carpet and screw them to the sub floor by using 4x5/8 screws. The carpet tap down trim must be even with the top of the track. Line the transition up with the track and fit one end into the moulding. Using a rubber mallet, tap the moulding until it engages with the track. Use your hand to guide the moulding into the track as you work your way down, tapping it in, similar to how you would close a plastic zip bag. Transition all the way into the track. You can use a little more force once you are sure it is properly engaged in the track. 3 of 8
7 Transition Moulding Transition - OPTIONAL DOWEL INSTALLATION Roughen up surface that comes in contact with glue NOTE: Transition Dowels are sold separately. Please contact your Sales Representative to order. 1.5 Side View of Transition Moulding Center one dowel Turn the transition over and use a sanding sponge, metal brush or 60 grit sandpaper to roughen up the surface to increase the bond on the side where glue will be applied. Each dowel tree (sold separately), contains 8 dowels. Carefully cut or break dowels off of tree. Slide one dowel into moulding groove and position in center of moulding. Insert additional dowels from both ends. Space dowels 11.5 apart and 1.5 from ends. NOTE: Dowels have to fit tightly for the moulding to function properly. If you find the dowel is too difficult to slide in, take 100/120 grit sandpaper, lay it flat on a surface and sand down the dowel head slightly with a couple of passes. 2 Pencil marks *If the flooring manufacturer suggests/permits the use of underlayments, you may need to shim the track to accomodate the increase in overall thickness Install the flooring planks*, by leaving a inch (25mm) gap for the installation of the moulding. Draw a line on the flooring for the placement of the holes. Using a drill bit, pre-drill holes into the flooring 2 deep. Be sure to use the same measurements as the dowels, keeping the holes 11.5 apart. With a pencil, mark on the floor where each dowel is located (You will need these for Step 7). Pencil marks should be about from the pre-drilled holes. NOTE: Be sure to vacuum pre-drilled holes. This end of the transition MUST be placed on the lower of the two surfaces. Pencil marks Step 4 Carefully line up dowels with pre-drilled holes. Make adjustments to the dowel positions on the moulding if needed. 4 of 8
8 Transition - OPTIONAL DOWEL INSTALLATION Push down directly over dowel at a time Side View of Hand Positions First pass () Second Pass () Third Pass () Forth Pass () NOTE: Do not try to push the entire molding in all at once by just pressing it in from top! This will bend the dowels. Step 5 Using both hands, start at one end and gently push moulding down. Make sure dowel is straight and that you apply pressure directly over dowel. The best position is to hold dowel with pointer and middle fingers and push down with thumbs. Moving down the moulding again, push the dowels in the floor at a time. It should take several passes to push the moulding all the way down. PUR-Glue adhesive About 3/8 (9.5mm) First pass () Second Pass () Third Pass () Forth Pass () Fifth Pass () Step 6 Once moulding is about a finger s width from the floor (about 3/8 or 9.5 mm), insert the tip of a glue gun under 1 edge of the moulding. Apply Liquid Nails or any polyurethane constructive adhesive along 1 side of the flooring. NOTE: Make sure you apply adhesive to ONLY 1 side of the moulding and that all surfaces that the adhesive touches is dust and debris free. Pencil marks Step 7 When finished applying adhesive, start again at the beginning of the moulding and push dowels all the way in until moulding is secure. Once moulding is in place, use a rubber mallet to tap on the top of each dowel. Use the pencil marks to reference where each dowel is located. 5 of 8
9 Transition Moulding Transition track - OPTIONAL DOWEL INSTALLATION: Installation for use on CONCRETE Transition Installation Instructions for Use on Concrete 2 Concrete 1 Flat object Pencil marks Drill bit Take Measurement Here Install flooring planks, leaving 1 inch gap for moulding installation. Draw line on flooring for hole placement. Using a concrete drill bit pre-drill 2 deep holes using same measurements as dowels. With pencil, mark on floor the location of each dowel. BE SURE TO VACUUM PRE-DRILLED HOLES. Lay a flat object over flooring and measure from the concrete at the center between the flooring up to the bottom of your object. This will give you the distance to use on the Dowel Cutting Template below. Dowel Cutting Template Dowel Cutting Template Concrete 2 Distance Measurement 3 Distance Measurement 4 5 3/4 NO CUT 5/8 1/2 3/8 1/8 Dowel Cutting Template is located to the right of Installation Instructions 3/4 NO CUT 5/8 1/2 3/8 Cut Here Cut Here 1/8 Roughen up surface that comes in contact with glue Carefully cut or break dowels from Dowel Tree. Use the Dowel Cutting Template to the right to find your measurement on the template and lay your dowel over the number that matches your distance measurement. With dowel on template, use a utility knife to cut dowel as indicated on Dowel Cutting Template. Repeat with all dowels that are to be used. Turn the transition over and use a sanding sponge, metal brush or 60 grit sandpaper to roughen up the surface to increase the bond on the side where glue will be applied. FOR CONCRETE ONLY! Dowel Cutting Template Distance Measurement 3/4 NO CUT 5/8 1/2 3/8 1/8 Slide dowels into groove on bottom of the transition moulding and position them according to template. Line up dowels with pre-drilled holes. Adjust dowels as needed. 6 NOTE: Dowels have to fit tightly for the moulding to function properly. If you find the dowel is too difficult to slide in, take 100/120 grit sandpaper, lay it flat on a surface and sand down the dowel head slightly with a couple of passes (See Detail A at the right). DETAIL A First pass () 7 Second Pass () Next Passes () About 3/8 (9.5mm) 8 PUR-Glue adhesive Pencil marks Using both hands, start at one end and gently push moulding down at a time. It should take several passes to push moulding all the way down. Best hand position is holding dowel between pointer fingers and pushing down with thumbs directly over dowel. DO NOT TRY TO PUSH ENTIRE MOULDING IN ALL AT ONCE. When moulding is a finger s width from the floor, insert tip of glue gun under one edge of moulding and apply a polyurethane construction adhesive along one side of the flooring. MAKE SURE YOU APPLY ADHESIVE TO ONLY ONE SIDE OF THE MOLUDING AND THAT ALL SURFACES THAT THE ADHESIVE TOUCHES IS DUST AND DEBRIS FREE. When finished applying adhesive, start again at beginning of moulding and push dowels all the way down until moulding is secure. Use a rubber mallet to gently tap on top of each dowel until molding sits flush. Use pencil marks as reference. 9 6 of 8
10 Transition TRANSITION MOULDING Transition Moulding Technical Information Sizes Transition Our Transition 3 in 1 Moulding functions as a Reducer, T-Moulding, and End Cap. Comes with TransitionTrack and Shim. Surface Material: High Wear Resistant Aluminum Oxide Laminaattee Core Material: PVC Transition To be used with transition track for floors from up to 3mm-4mm thickness including 3/32nd underlayment. Also, used in conjunction with the Shim for 4-6mm* including 3/32nd underlayment. Material: Cold Roll Steel * For floors thicker than 6mm, use optional dowel installation Dowel (Sold Separately) Optional use with Transition for floors from 0 up to 19mm. Comes as a tree of eight dowels. Material: Polystyrene Up to 4mm LVT Solution 1/8 3/16 2 9/16 7/16 9/16 1 Reducer: 2 Transition: 3 5-6mm 3 1 in Up to 3mm 4-6mm 2 13/64 End Cap: (Hard Surface to Carpet) Up to 3-6mm New & Improved PVC Molding 1 SlimTrack Reducer: Up to 3/4 Shim Optional Dowel Installation Carpet Tap Down Trim 2 Transition: 3 End Cap: (Hard Surface to Carpet) Up to 3/4 Up to 3/4 Glue Dowel (Sold Separately) A Carpet Tap Down Trim MUST be Used When Installing Transition on Carpet Carpet Tap Down Trim Vinyl to 3/4 Inch Laminate to Laminate Laminate to Ceramic Tile Laminate to Sliding Door Piece of Laminate Used as Shim NOTE: Transition does not work on radiant heat floors with optional dowel installation method. Sliding Door All mouldings are 94 long (7 10 ) 7 of 8
11 RECOMMENDED TOOLS FOR INSTALLATION Stairnose Pencil Tape measure Miter saw 60 grit sandpaper Metal brush Caulk gun PUR-glue Damp cloth Transition Pencil Tape measure Miter saw Utility knife Screwdriver Drill w/screw & drill bit Rubber mallet Caulk gun Damp cloth PUR-glue Small screws 4 x 3/4 or 5/8 8 of 8
Laminate Flooring T-Lock Angle-Drop Installation Instructions
TECHNICAL SERVICE Laminate Flooring T-Lock Angle-Drop Installation Instructions March 23, 2012 Read all instructions carefully before beginning installation. Make sure that the instructions are the most
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationComposite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
More informationHOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY
HOW-TO HOW-TO LAY HARDBOARD OR PLYWOOD FLOOR OVERLAY Most floor coverings, if laid over uneven wooden floors, will wear unevenly and look unsightly. The answer is to cover the old boards with hardboard
More informationSTAIR TREAD & RISER INSTALLATION GUIDELINES
STAIR TREAD & RISER INSTALLATION GUIDELINES ARTISTIC FINISHES DOES NOT WARRANTY THE COMPLETENESS OR ACCURACY OF ANY INSTALLATION. THE INSTALLATION CONTRACTER MUST HAVE THE EXPERIENCE AND KNOWLEDGE TO COMPLETE
More informationHow to Install Hardwood Flooring Over a Sub Floor
How to Install Hardwood Flooring Over a Sub Floor Installation Preparation Instructions Read the entire instructions before starting your project. 1) INSPECT EACH PLANK (see fig. a) Wood is a natural product
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationINSTALLATION RECOMMENDATIONS. Outdoor Rubber Tiles
INSTALLATION RECOMMENDATIONS Outdoor Rubber Tiles Prior to Installation: The Outdoor Rubber Tiles and accessory transition pieces intended for this installation have been shipped to you via a freight carrier
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationHow To Level A Subfloor
Skill Level: INTERMEDIATE Give these projects a try if you're a confident DIYer with a good working knowledge of a variety of tools. They can take a day or more to complete. If you can build a birdhouse
More informationInstalling Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
More informationWindow Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
More informationChoosing the Right Floor Protectors
Choosing the Right Floor Protectors You ve made the investment in new flooring for your home. So what can you do to help ensure your flooring stays looking like new? One of the biggest flooring maintenance
More informationINSTALLATION INSTRUCTIONS FOR LAMINATE FLOORING
INSTALLATION INSTRUCTIONS FOR LAMINATE FLOORING Introduction Laminate flooring is designed to be a floating floor that may be installed over virtually any type of sub floor. It is not nailed or glued to
More informationGARDEN WINDOW GLAZING AND DE-GLAZING INSTRUCTIONS
GARDEN WINDOW GLAZING AND DE-GLAZING INSTRUCTIONS DE-GLAZING 1.) If there is any PVC cement covering the joints where external glazing bead strips meet, cut through the cement with a utility knife. 2.)
More informationPlease calculate with around 5% more square meters than needed because you will have material loss due to cutting and sorting.
1. TEKA Soft Loc Installation Guide Thank you for having chosen TEKA Parquet. To guarantee a constant quality product TEKA engineered hardwood flooring is made out of selected wood species and runs only
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationGear PEPSI CAN STOVE INSTRUCTIONS
Gear PEPSI CAN STOVE INSTRUCTIONS [NOTE: Updated Instructions are now available. The new stove is less likely to develop flame leaks and the fuel/air mixture is improved. Instructions for a simmer ring
More informationLadder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More information0800 30 50 90 www.bamboodirect.co.nz
Guide To Bamboo Flooring 1. Frequently Asked Questions 2. Installation Tips 3. Maintaining your Bamboo Floor 4. Why Bamboo Direct? COPYRIGHT 2009 BAMBOO DIRECT Frequently Asked Questions 1. Are Bamboo
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. GeneralShale.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide GeneralShale.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More informationBrick Veneer Construction
Brick Veneer Construction Check list of suggested tools & support items Claw hammer Tape measure 3/4" [19 or 20] Wood chisel Wood or plastic shims Pry bar Utility knife Caulking and caulking gun Power
More informationPANELIZED HOME INSTALLATION GUIDELINE
PANELIZED HOME INSTALLATION GUIDELINE A typical home package will be constructed of Snap-N-Lock Insulated Panels clad with steel skins. 4" panels will be used for the walls, and 6" panels for the roof.
More informationReplacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin americancraftsmanwindows.com Project Requirements: Failure to follow these instructions may void product
More information1 Door Tall Unit ASSEMBLY GUIDE. Page 1 of 9. WARNING: Contains small parts, keep out of reach of children.
Page 1 of 9 ASSEMBLY GUIDE 1 Door Tall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please
More informationCustomer Service 800.780.8889 or visit us online at smithnoble.com. Wood Shutters. Step by Step Installation. Troubleshooting Tips
reflect your style TM Customer Service 800.780.8889 or visit us online at smithnoble.com Wood Shutters Step by Step Installation Troubleshooting Tips Easy Care Instructions STEP 1 Your New Shutter Thank
More informationHow to Install GoBoard:
How to Install GoBoard: A Step-by-Step Guide Durable, Ultra-Lightweight, Waterproof Tile Backer Board Introducing GoBoard Every tiling project requires a durable, waterproof surface under the tile, called
More informationSun Windows General Information Sun New Construction Window Installation Instructions
Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten
More informationVinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows
Vinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows Viewed from the exterior. IMPORTANT: Please read before you begin installation. TABLE OF CONTENTS AND TOOL / MATERIAL
More informationHow to build a Pizza Oven in 4 days
How to build a Pizza Oven in 4 days Preparation day (slab) 1. Foundation 1500 deep x 1300 wide x 75mm deep Required 20 bags cement pre mix. If you already have a concrete base, you save this prep day DAY
More informationAspect Metal Peel & Stick Tile Installation Guide
Aspect Metal Peel & Stick Tile Installation Guide Proper surface preparation is essential for a successful project Failure to follow recommended surface preparation instructions may void the warranty Read
More informationHALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL
HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL Please read these instructions carefully and completely before attempting to install Hale Pet Doors; they will guide you through the steps
More informationHow to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
More informationEucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in handling.
i This instruction sheet describes the proper methods for installing Eucatex decorative wall paneling. Eucaboard / Eucaplac/ Eucatile paneling is intended for dry interior use only and requires care in
More informationGrand Mesa Plus LAMINATE - WIRE BRUSHED. GAGVGM81012A Prairie. GAGVGM80012NA Colorado. GAGVGM84012A Pecan Rustic. GAGVGM85012A Saddle Walnut
MARCH 2015 Grand Mesa Plus LAMINATE - WIRE BRUSHED Specifications 12.3mm 6.5 wide x 47-13/16 long 19.42 sf/ctn 48 ctn/plt Triple Plate Embossing Wire Brushed Texture Micro-Bevel & Waxed Edges Warranty
More informationStair Railing. Installation Guide
Stair Railing Installation Guide THE BEST CHOICE FOR STRONG & DURABLE RAILING SYSTEMS Our exclusive manufacturing process ensures our vinyl railing will provide superior strength plus it is virtually maintenance
More informationInstallation for Wood Flooring
Installation for Wood Flooring Tarkett wood flooring offers a beautiful variety of options from species and colour, to plank widths and finishes. We developed enhanced locking system, T-lock, and the best
More informationINSTRUCTION MANUAL TOOLS NEEDED FOR ASSEMBLY: OPTIONAL FINISHING MATERIALS: Champaign, Illinois (217) 398-8970 E-mail: partssupport@hobbico.
INSTRUCTION MANUAL Thank you for purchasing the Hobbico Ultra-Tote! You have purchased one of the finest values available in field support equipment. We think you will be impressed with the design and
More informationREDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES
REDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES Tools Required Tape Measure Hammer Slotted Screw Driver #2 & #3 Philips Screw Driver 3-4 Foot Level 12 Pry Bar Cold Chisel
More informationRouter Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationHere is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
More informationOvernight Sensations Speaker Kit
Overnight Sensations Speaker Kit Thank you for purchasing the Overnight Sensation cabinet kit. This speaker kit was precision cut using CNC machinery for the best possible fit and finish. With a little
More informationFREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Tools and Glue. Required Materials
Do not try to make your ornithopter using "household materials". If you want it to fly, you have to build it right. FREEBIRD THE ORIGINAL D.I.Y. ORNITHOPTER! Wingspan: 16 inches Weight: 1/4 ounce The Ornithopter
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationNATURAL RAILING INSTALLATION INSTRUCTIONS
NTURL RILING INSTLLTION INSTRUCTIONS Manufactured by fiberondecking.com 800.573.8841 FI-0217-PKG 5/14 Natural Railing Installation Instructions Natural Top Rail Profile Required Tools and Supplies: Power
More informationVC 104+ Rigid Grade / Rigid Grade Imagine VC 104 Rigid Grade Commercial Customised
Page 1 of 6 instructions VC 104+ Rigid Grade / VC 104+ Rigid Grade Imagine / (for the rest of this document referred to as VC 104) can be applied to new and used trucks and trailers with painted rigid
More informationHOW TO INSTALL A BEAUTIFUL NEW KITCHEN
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge
More informationHow to Install UnderDeck The Original.
How to Install UnderDeck The Original. TOOLS: Chalk Line Caulk Gun Garden hose or water bucket Gloves Hammer or Screw Gun Power Mitre Saw with OSB Blade Pencil Pliers Safety Glasses Straight Edge / Carpenter
More informationTotal Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL
More informationWritten By: Walter Galan
ipad 2 GSM Rear Camera Replacement Replace the rear camera in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Use this guide to replace a broken rear camera. TOOLS: ifixit Opening Picks set of 6
More informationBella Cera Engineered Hardwood Flooring Installation Instructions. Check for Proper Color Selection Prior to Installation
Bella Cera Engineered Hardwood Flooring Installation Instructions Check for Proper Color Selection Prior to Installation 1 Important Information before You Begin 1.1 Installer/Owner Responsibility Carefully
More informationBUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS
BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationBuild a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic
Build a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic Coated Paper 2 Balsa Sheets (10-1/2 x4 x3/16 ) 2 Alligator
More informationW I T H I N J O I ST S I N STA L L AT I ON
Radiantec W I T H I N J O I ST S I N STA L L AT I ON I N S TA L L AT I O N S U P P L E M E N T 260 Joists When tubing is placed beneath a joisted floor system, it is weaved between the joists and supported
More informationBLADE REPAIR INSTRUCTION BOOKLET
BLADE REPAIR INSTRUCTION BOOKLET Contents Section I: Section II: Section III: Section IV: Section V: Section VI: Removing a Blade Refer to this section if you need to remove the blade from an oar shaft.
More informationSPIRAL STAIR KIT INSTALLATION MANUAL
SPIRAL STAIR KIT INSTALLATION MANUAL Effective January 1, 2014 If you have any questions, please call the location that your Stair Kit was purchased from: Broomall, Pennsylvania 1-800-52-7427 Ontario,
More informationBlack Wolf POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Black Wolf TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905710-000 SEPTEMBER 2010 NOTE: Please use the instructions in this
More informationChelsea Loft Bed WARNING:
Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More information3. Choose between an easy table (24 inches wide) and a hard table (20 inches wide).
Ultra Carpetball Plans Version 2.0 The Best (And Only) Free Carpetball Plans On The Web By Matthew Campbell Instructions: 1. Read these instructions all the way through and look at all the diagrams before
More informationTHINGS YOU SHOULD KNOW
INSTALLATION INSTRUCTIONS Value Sized Roll The quickest, easiest, cleanest way to install tile. No Mortar, No Mixing, No Mess Complete Your Project in a Day No Waiting Between Setting and Grouting THINGS
More informationModels A spe n, Econoline C o l o n i al. and Savoy. Installation Instructions. Contractors Wardrobe
Installation Instructions Models A spe n, Econoline C o l o n i al and Savoy Contractors Wardrobe DESIGNERS MANUFACTURERS TOLL FREE: (800) CW-DOORS (800) 293-77 www.cwdoor.com 2121 Avenue Hall Valencia,
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationStaircase Installation Instructions
Staircase Installation Instructions www.cooperstairworks.com 8/02 Pre-Assembled Stair Installation Instructions Read thoroughly before starting installation 1. Check floors, top and bottom to determine
More informationmajestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base
majestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base These Instructions are for a left and right handed unit. The diagrams show a left
More informationINSTALLATION IMPORTANT INSTALLER/OWNER RESPONSIBILITY TOOLS & EQUIPMENT NEEDED FOR INSTALLATION PRE-INSTALLATION PROCEDURES & JOBSITE CONDITIONS
IMPORTANT It is important that you read & understand the following information and instructions in their entirety before proceeding with installation. Please thoroughly inspect all Flooring products in
More informationTopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
More informationInstructions for Using the Watch Works Tool Kit to Change a Watch Battery
Instructions for Using the Watch Works Tool Kit to Change a Watch Battery Click on this link http://www.allamericanwatches.com/site/626101/product/e2306-a to purchase the Watch Battery Replacement Tool
More informationFAQs. 19. Does the sub floor need to be level before I install my new direct-to-stud bathtub or shower base?
1. Where is the serial number of my tub located? 2. What can I use to clean my tub or shower? 3. What is an Above Floor Rough-in? 4. Can I replace my towel bar? 5. What are grommets? 6. Why do some bathing
More informationINSTALLATION INSTRUCTIONS for Premium Pocket Windows (JII022) IMPoRtaNt INFoRMatIoN & glossary. safety & HaNdlINg
Thank you for selecting JeLd-weN products. Attached are JeLd-weN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationProfiles. Exclusively Manufactured By
Profiles and TRANSITIONS Exclusively Manufactured By PrORound Introducing a new choice in high quality Profiles and Transitions. Enhance the beauty of tile and natural stone surfaces in your projects with
More informationWritten By: Walter Galan
ipad 2 GSM Front Panel Replacement Replace the front panel in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Note: this is a complete guide for replacing a plain front panel. If you have a Front
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationBasic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
More informationBasement Window Installation Guide Hopper and Sliding
Basement Window Installation Guide Hopper and Sliding americancraftsmanwindows.com Project Requirements: Installation must comply with all applicable building codes. Existing window frame, wall and weatherresistant
More informationSTONE PANELS, INC. 100 South Royal Lane Coppell, TX 75019 Phone: (469) 635-5000 * Toll Free: (800) 328-6275 Fax: (469) 635-5555
STONE PANELS, INC. 100 South Royal Lane Coppell, TX 75019 Phone: (469) 635-5000 * Toll Free: (800) 328-6275 Fax: (469) 635-5555 INTERLOCKING CHANNEL ATTACHMENT STEEL STUD FRAMING OR FURRING CONSTRUCTION
More informationENGINEERED FLOORING INSTALLATION
ENGINEERED FLOORING INSTALLATION ATTENTION! INSTALLER/OWNER RESPONSIBILITIES Beautiful hardwood floors are a product of nature and, therefore, they will show variations in color, grain, texture, and appearance.
More informationVINYL CLICK FLOORING INSTALLATION GUIDE
VINYL CLICK FLOORING INSTALLATION GUIDE Owner/Installer Responsibility Prior to installing a single board, you or the installer must determine that the job-site environment and the sub-surfaces meet the
More informationGuidelines for Earthquake Bracing Residential Water Heaters
Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More informationBuilding an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
More informationArmstrong Do-It-Yourself Tile Installation System
Armstrong Do-It-Yourself Tile Installation System What tools will I need to install my tile floor? You'll need just the basics: - floor tile (make sure you have enough tile to finish the job) - adhesive
More informationHeavy Glass Frameless Shower Door With Return Panel
202 Anderson Ave., elvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com Heavy Glass Frameless Shower Door With Return Panel Full Showers with Return ench Seat with Return FRLSDRPL-0116
More informationAir Hockey Training Camp Care and repair of your Air Hockey Playfield
The playfield is the single most expensive part of your Dynamo Air Hockey table. Proper care will keep your table attractive and functional for your players, and bring them back for more games. CLEAN YOUR
More informationIndustrial Strength Rocket Launcher
Industrial Strength Rocket Launcher Description: Instructions for the construction of an industrial strength rocket launcher for use with paper rockets. Materials: Schedule 40 PVC piping and bushings from
More informationThese instructions will show you how to install an internal door into a non-loadbearing partition wall. The instructions are split into three parts.
No 8 in the series of 'How to' brochures produced by PlaceMakers, New Zealand How to Frame and Hang a Door These instructions will show you how to install an internal door into a non-loadbearing partition
More informationShower Walls and Tub Surrounds
Reverso en español TEC Skill Set How-To Project Guide Shower Walls and Tub Surrounds 3 Steps to a Beautiful Tile Surface! 1. Prepare the surface 2. Set the tile 3. Grout and caulk H.B. Fuller Construction
More informationInstalling Window Trim and Door Trim
Installing Window Trim and Door Trim Tools and Supplies You'll Need Screws or Finish Nails use screws or nails that are long enough to go through the Ledger and firmly attach to the wall behind it. If
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationPremier & Deluxe 3-Season Room Sliding Glass Door
DTSSGD-11 Premier & Deluxe 3-Season Room Sliding Glass Door Installation Instructions Screen Door Seal Left Side Track Top Track Assembly Right Side Track Right Side Trim Sliding Glass Door Sliding Screen
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW
Vinyl Windows and Doors Manufactured by Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW Lea las instrucciones en español en el reverso.
More informationFiberglass-Reinforced Sheet Flooring Installation System
Fiberglass-Reinforced Sheet Flooring Installation System Product Adhesive Comments Residential Use Only CushionStep Value Good Better Best FlexStep Duality Premium Premium Plus Modified loose lay method
More information