Incremental encoders With blind or through hollow shaft pulses per revolution programmable
|
|
|
- Michael Turner
- 7 years ago
- Views:
Transcription
1 Features Size ø58 mm Precise optical sensing Output signal level programmable (TTL or HTL) Blind hollow or through hollow shaft, ø8 15 mm Connection axial, radial or tangential Pulses per revolution , programmable High protection up to IP67 High resistance to shock and vibrations EIL580P with blind hollow shaft Technical data - electrical ratings Voltage supply Reverse polarity protection Yes Short-circuit proof Consumption w/o load Initializing time VDC Yes 70 ma Pulses per revolution Duty cycle 30 ms after power on % typical at 2048 ppr Reference signal Zero pulse 90 or 180 Sensing method Optical Output frequency 300 khz (TTL) 160 khz (HTL) Output signals A+, B+, R+, A-, B-, R- Output stage TTL/RS422 HTL/push pull Programmable parameters Output level TTL/HTL Pulse number Zero pulse width 90 /180 Zero pulse position Signal sequence Interference immunity DIN EN Emitted interference DIN EN Approval UL 508 / CSA 22.2 Technical data - mechanical design Size (flange) Motor shaft tolerance Protection DIN EN ø58 mm 0.2 mm axial 0.03 mm radial IP 65 (without shaft seal), IP 67 (with shaft seal) Starting torque 0.02 Nm (+20 C, IP 65) Nm (+20 C, IP 67) Materials Housing: aluminium die-cast Flange: aluminium Operating temperature C Relative humidity 90 % non-condensing Resistance DIN EN Vibration 30 g, Hz DIN EN Shock 250 g, 6 ms Connection Flange connector M12, 8-pin Flange connector M23, 12-pin Cable Weight approx. 300 g EIL580P - blind hollow shaft Shaft type ø mm (blind hollow shaft) Operating speed 6000 rpm (+20 C, IP 67) 8000 rpm (+20 C, IP 65) EIL580P - through hollow shaft Shaft type ø mm (through hollow shaft) Operating speed 3000 rpm (+20 C, IP 67) 6000 rpm (+20 C, IP 65) 1
2 Part number Blind hollow shaft EIL580P- B B Operating temperature B C Pulses programmable (factory setting) F Q Voltage supply / output circuit VDC, TTL/RS422, 6 channel (Vout = 5 VDC) - Factory setting VDC, HTL/push pull, 6 channel (Vout = Vin) R L F B T U D A P Q Connection Cable radial, 1 m Cable radial, 2 m Flange connector M23, 12-pin, radial, pin terminals, ccw Flange connector M12, 8-pin, radial, pin terminals, ccw Cable axial, 1 m Cable axial, 2 m Flange connector M23, 12-pin, axial, pin terminals, ccw Flange connector M12, 8-pin, axial, pin terminals, ccw Cable tangential, 1 m Cable tangential, 2 m Protection 5 IP 65 7 IP 67 B N T P Specification hollow shaft 08 ø8 mm, clamping ring at A side U4 ø1/2 (12.7 mm), clamping ring at A side U3 ø3/8 (9,52 mm), clamping ring at A side 14 ø14 mm, clamping ring at A side 10 ø10 mm, clamping ring at A side 15 ø15 mm, clamping ring at A side 12 ø12 mm, clamping ring at A side Flange Without stator coupling With stator coupling ø63 mm Pin torque support 3 mm, axial/radial Shaft type Blind hollow shaft Printed in bold = standard items (up to the quantity of 10 will be supplied within 5 working days). (Factory setting: 1024 ppr, Vout = 5 VDC TTL, signal sequence A leads B (CW), zero pulse 90 A&B high) pulses programmable. Stock items EIL580P-BT12.5FF B EIL580P-BT14.5FF B Numerous stock items in single quantity will be supplied within 24 hours respectively one day ex works. 2
3 Part number Through hollow shaft EIL580P- T B Operating temperature B C Pulses programmable (factory setting) F Q Voltage supply / output circuit VDC, TTL/RS422, 6 channel (Vout = 5 VDC) - Factory setting VDC, HTL/push pull, 6 channel (Vout = Vin) R L F B P Q Connection Cable radial, 1 m Cable radial, 2 m Flange connector M23, 12-pin, radial, pin terminals, ccw Flange connector M12, 8-pin, radial, pin terminals, ccw Cable tangential, 1 m Cable tangential, 2 m Protection 5 IP 65 7 IP 67 Specification hollow shaft 08 ø8 mm, clamping ring at A side U4 ø1/2 (12.7 mm), clamping ring at A side U3 ø3/8 (9,52 mm), clamping ring at A side 14 ø14 mm, clamping ring at A side 10 ø10 mm, clamping ring at A side 15 ø15 mm, clamping ring at A side 12 ø12 mm, clamping ring at A side T N T P Flange Without stator coupling With stator coupling ø63 mm Pin torque support 3 mm, axial/radial Shaft type Through hollow shaft Printed in bold = standard items (up to the quantity of 10 will be supplied within 5 working days). (Factory setting: 1024 ppr, Vout = 5 VDC TTL, signal sequence A leads B (CW), zero pulse 90 A&B high) pulses programmable. Stock items EIL580P-TT12.5FF B EIL580P-TT14.5FF B Numerous stock items in single quantity will be supplied within 24 hours respectively one day ex works. 3
4 Accessories Connectors and cables Connection cable 2 m shielded with female connector M12, 8-pin, straight (ESG 34FH0200G) Connection cable 5 m shielded with female connector M12, 8-pin, straight (ESG 34FH0500G) Connection cable 10 m shielded with female connector M12, 8-pin, straight (ESG 34FH1000G) Connection cable 2 m shielded with female connector M12, 8-pin, angled (ESW 33FH0200G) Connection cable 5 m shielded with female connector M12, 8-pin, angled (ESW 33FH0500G) Connection cable 10 m shielded with female connector M12, 8-pin, angled (ESW 33FH1000G) Connector M23, 12-pin Connection cable 1 m shielded with female connector M23, 12-pin Connection cable 2 m shielded with female connector M23, 12-pin Connection cable 5 m shielded with female connector M23, 12-pin Connection cable 10 m shielded with female connector M23, 12-pin Connection cable connector M12 / connector D-SUB, 0.2 m Connection cable connector M12 / connector D-SUB, 1 m Connection cable connector M23 / connector D-SUB, 0.2 m (S2BG12/K4SG9) Connection cable connector M23 / connector D-SUB, 1 m (S2BG12/K4SG9) Mounting accessories Torque arm, 1-arm, bolt circle ø82 mm, mounting M4 (mounting kit 003) Torque arm, 1-arm, bolt circle ø74 94 mm, mounting M4/M5 (mounting kit 006) Torque arm, 1-arm, bolt circle ø mm, mounting M4, can be cut to length (mounting kit 021) Torque arm, 1-arm, bolt circle ø74 94 mm, mounting M6 (mounting kit 028) Torque arm, 1-arm, bolt circle ø mm, mounting M4 (mounting kit 047) Stator coupling, 2-armed, bolt circle ø63 mm, mounting M3 (mounting kit 046) Accessories Mounting accessories Fan Cover Clip 8 mm Clamping ring 12/31/ 8 M3 8.8 for EIL580 hollow shaft ø8...ø10 mm Clamping ring 17/31/ 8 M3 8.8 for EIL580 hollow shaft ø12...ø15 mm Programming accessories Handheld Programming Tool Z-PA-EI-H PC Programming Tool Z-PA-EI-P 4
5 Output signals A+ A- B+ B- R+ R- Zero pulse electrical 90 A&B high (Factory setting at clockwise rotation (CW) in view of the encoder flange) Zero pulse electrical 180 B low (at clockwise rotation (CW) in view of the encoder flange) Terminal assignment Flange connector M23, 12-pin / cable Pin Core color Assignment 1 pink B- 2 3 blue R+ 4 red R- 5 green A+ 6 yellow A- 7 8 grey B white GND brown UB Screen: Connected to housing Cable data: PUR, [4x2x0.14 mm 2 ], bending radius >45.8 mm, Outer diameter 6.1 mm A+ A B+ B- R+ R- Trigger level Outputs Output level High Output level Low Load Outputs Output level High Output level Low Load TTL/RS V 0.5 V 20 ma HTL/Push-pull UB -3 V 1.5 V 20 ma Flange connector M12, 8-pin Pin Assignment 1 GND 2 UB 3 A+ 4 A- 5 B+ 6 B- 7 R+ 8 R
6 Dimensions Blind hollow shaft, flange connector M12 radial Blind hollow shaft, flange connector M12 axial Through hollow shaft, flange connector M12 radial Blind hollow shaft, flange connector M23 radial 6
7 Dimensions Blind hollow shaft, flange connector M23 axial Through hollow shaft, flange connector M23 radial Blind hollow shaft, cable radial Blind hollow shaft, cable axial 7
8 Dimensions Blind hollow shaft, cable tangential Through hollow shaft, cable radial Through hollow shaft, cable tangential Pin torque support, axial 8
9 Dimensions Pin torque support, radial Blind hollow shaft Through hollow shaft 9
10 Dimensions 10
Housing diameter Shaft diameter 1. Flange (Mounting of housing) Protection class shaft input (EN 60529) Protection class housing (EN 60529)
Direct mounting without coupling Flexible hollow shaft design up to diameter 4 mm Through hollow shaft or as end shaft (blind shaft) Easy installation by means of clamping shaft or blind shaft Short overall
TECHNICAL DATASHEET Incremental Encoder RI 58-D / RI 58TD
Direct mounting without coupling Flexible hollow shaft design up to diameter 4 mm Through hollow shaft or as end shaft (blind shaft) Easy installation by means of clamping shaft or blind shaft Short overall
How To Power A Schen
Automation / Mini Type SCH32F Hollow Shaft Encoder - Ø 32 mm Hollow Bore: Ø 6 mm to Ø 3/8 inch Resolution up to 5000 ppr IP 65 (IP 50 for IDC connector option) Electrical Specifications Code: Resolution:
Material: Weight: Bearing Life: Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads:
Automation / Mini Type SCH32F Hollow Shaft Encoder - Ø 32 mm Hollow Bore: Ø 6 mm to Ø 3/8 inch Resolution up to 5000 ppr IP 65 (IP 50 for IDC connector option) Electrical Specifications Code: Resolution:
TECHNICAL DATASHEET Incremental Encoder RI 58-H
Through hollow shaft High accuracy by means of integrated flexible coupling Safe shaft mounting Applications: textile machines, motors, drives, copiers NUMBER OF PULSES 1 / 2 / 3 / 4 / 5 / 10 / 15 / 20
IP40 or IP64 (EN 60529) Protection class housing. IP50 (IP65 optional) (EN 60529) Minimum length of mountig
Through hollow shaft Ø 5 bis 4 mm Outside diameter only 76 mm Easy installation by means of clamping ring front or rear Operating temperature up to 00 C Applications: motors, printing machines, lifts NUMBER
Contactless Encoder RI360P0-QR24M0-INCRX2-H1181
Compact, rugged housing Many mounting possibilities Status displayed via LED Immune to electromagnetic interference 1024 pulses per revolution (default) 360, 512, 1000, 1024, 2048, 2500, 3600, 4096, parametr.
Technical data. General specifications. Signal voltage 15... 30 V DC Signal duration. 1 s Input 2. Signal voltage. 1 s Analog output.
Model Number Features Very small housing High climatic resistance 4 Bit multiturn Analog output Surge and reverse polarity protection Description This absolute rotary encoder with internal magnetic sampling
Material: Weight: Bearing Life: Shaft Loads: Operating Temp.: Storage Temp.: Shock: Vibration: Bump: Humidity: Enclosure Rating: Cable: Cable Glands:
Oil & Gas / Heavy Industry EX-Proof Stainless Steel Shaft Encoder - Ø 68 mm Shaft - Ø 10 mm to Ø 5/8 inch Resolution up to 10,000 ppr IP 66 (IP 67 option) ATEX certified EX-Proof IECEx certified EX-Proof
TECHNICAL DATASHEET Incremental Encoder RI 80-E
Incremental 30-45 hollow shaft Rugged mechanical design Unbreakable disc Integrated diagnostic system Wide voltage range DC 5-30 V Isolated shaft NUMBER OF PULSES 1024 / 2048 / 2500 / 4096 / 5000 / 10000
RoHS. Shock / vibration resistant. Magnetic field proof. Many variants
Sendix 5000 / 500 (Shaft / Hollow shaft) Push-Pull / RS4 ue to their sturdy bearing construction in Safety-ock esign, the Sendix 5000 and 500 offer high resistance against vibration and installation errors.
TECHNICAL DATASHEET Incremental Encoder RI 58-O / RI 58-T
Universal industry standard encoder Up to 40 000 steps with 0 000 pulses High signal accuracy Protection class up to IP67 Flexible due to many flange and configuration variants Suitable for high shock
Description. Dimensions. Features. www.pwb-encoders.com. precision works better
Description The MEC22 is a high resolution optical hollow shaft encoder that can be fixed quickly and easily on different sizes of motor shafts. The encoder provides two square wave outputs in quadrature
Series 7500 Torque Sensor
Properties PTO (Power Take-Off) shaft with integrated torque and angle measurement Non-contact measurement system, high robustness Plug & Play solution, no additional electronics required Performance Measurement
ABSOLUTE ROTARY ENCODER ETHERNET/IP
Main Features - Compact and heavy duty industrial model - Interface: EtherNet/IP - Conformance tested by ODVA - Housing: 58 mm - Full shaft: 6 or 10 mm / hollow shaft15 mm - Resolution: max. 30 Bit = 1,073,741,824
LED red (-): Measuring value < lower tolerance threshold LED red (+): Measuring value > upper tolerance threshold. Page 1/6
L-LAS Series L-LAS-LT-165-CL - Line laser 1 mw, laser class 2 - Visible laser line (red light 670 nm), typ. 2 mm x 3 mm - Reference distance approx. 165 mm - Measuring range typ. 65... 265 mm - Resolution
Encoder WDGI 58H. www.wachendorff-automation.com/wdgi58h
Encoder WDGI H www.wachendorffautomation.com/wdgih Wachendorff utomation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and customer versions
QR12 (1.22 ) Diameter Optical Encoder
Improving the Quality of Life through the Power in Light QPhase QR12 (1.22 ) Diameter Optical Encoder Design Features: Low profile assembled height of Bearing design simplifies encoder attachment Resolutions
+ Incremental interface
i IEH58-INC-1-GB-1 04/12 Revision 01 010101-00589999-9999 + Incremental interface + Type with hollow through shaft + Modular product line + Extensive parameter setting possibilities + Special parameters
T-SERIES INDUSTRIAL INCLINOMETER ANALOG INTERFACE
T-SERIES INDUSTRIAL INCLINOMETER ANALOG INTERFACE T-Series industrial inclinometers are compact high performance sensors used to determine inclination in roll and pitch axes with excellent precision and
Vert-X 16-5V / 10...90% Ub. Applications Servodrives Dancer arm Operating table
Version MH-C MH-C2 Electrical data Measuring range 0... 360 - Indep. linearity % meas. range ±0.3 - Max. hysteresis 0.1 - Resolution bit 12 - Max. repeatability 0.1 - Sample rate fast mode khz (5) - Sample
Borstlösa DC-motorer. Promoco Scandinavia AB
Borstlösa DC-motorer Promoco Scandinavia AB BL Series Brushless DC Motors with Integral Drive 24, 54, 68, and 70 mm diameters, 2W up to 110W output power Allied Motion s BL series of small brushless DC
Sense it! Connect it! Bus it! Solve it! EncoderS
Sense it! Connect it! Bus it! Solve it! EncoderS Incremental encoders Incremental encoders use electrical pulses to measure rotation speed or position. The dual-channel incremental encoders of the Ri series,
Absolute Rotary Encoder E6CP
Absolute Rotary Encoder Absolute Rotary Encoders with Gray Code Output Gray code output decreases output errors Lightweight plastic housing Used with Omron s H8PS Cam Positioner, this encoder detects the
Series 6000 Torque measured metal bellow coupling
Properties Free of float metal bellow coupling with integrated torque measurement Non-contact measurement system, high robustness High torsional stiffness Limited torque of inertia Performance Measurement
Encoder WDG 58B. www.wachendorff-automation.com/wdg58b
Encoder WDG www.wachendorffautomation.com/wdgb Wachendorff utomation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and customer versions Maximum
LENORD. +BAUER... automates motion. PowerDRIVE-Positioning GEL 6109 Compact positioning drive for installation situations with limited space
PowerDRIVE-Positioning GEL 6109 Compact positioning drive for installation situations with limited space LENORD +BAUER... automates motion. Technical information Version 2014-09 General The PowerDRIVE-Positioning
-Encoder with end or hollow shaft ø10-15 mm. hollow shaft ø12 mm -Resolution max. 32 ppr. -Resolution max. 1024 ppr -Magnetic sensing
Incremental encoders Compact configurations Shaft ø4 mm and ø5 mm End shaft ø8-16 mm Hollow shaft ø6-15 mm Optical and magnetic sensing Resolution max. 2048 pulses Rotation speed max. 12000 rpm Protection
maxon sensor maxon sensor
Sensor Spindle drive Gearhead E Motor (BLD Motor) D Motor X Drives (configurable) Motor control obust encoders, D tachometers, and resolvers with high accuracy and high signal resolution. Due to resonance,
L-LAS-TB-CL serie. laser light curtains for inline measuring tasks
L-LAS-TB-CL serie laser light curtains for inline measuring tasks Maximum distance 2.000 mm Measurement range 6 up to 98 mm Resolution up to 4 µm up to 1,5 khz scan rate 0-10 V or 4-20 ma analogue output
Ferrostat Speed Sensor Series DSF Explosion Proof Versions EEx
Ferrostat Speed Sensor Series DSF Explosion Proof Versions EEx DSF..10.**.HV Ex ATEX Operating Instructions 374E-64368 Valid from lot nr. 0103 General Function Use in potentially explosive environment
Product Information. Gateway For Connecting EnDat Encoders to PROFIBUS-DP
Product Information Gateway For Connecting EnDat Encoders to PROFIBUS-DP April 2012 PROFIBUS Gateway For Connecting EnDat Encoders Encoders with EnDat interface for connection via gateway All absolute
Adjustment functions for both span and shift have been incorporated
SENSORS FOR SERIES LED Type Wafer Alignment Sensor FX-0-F FT-F9 FD-F7 EX-F70/F60 M SH-7 FD-L4 M-DW The use of a safe LED light beam now allows for high precision detection with a resolution of 0!m (.8
Incremental Rotary Encoder E6B2
Incremental Rotary Encoder General-Purpose Rotary Encoder Withstands arge Shaft oads Wide variety of supply voltages and output forms Easy-to-adjust zero index (phase Z) with origin indicating function
SENSORS. Fiber Optic Sensors - S70. Advanced fiber optic amplifiers for high speed and low contrast applications
Fiber Optic Sensors - S7 Advanced fiber optic amplifiers for high speed and low contrast applications DIN rail mountable models with dual digital displays speed models: 2 μs...5 ms Super high speed models:
Tubular Analog model resolution: 0,5 mm (SLOW mode), 1 mm (FAST mode) Right angle Repeatibility: 0,7 mm Vdc
Ultrasonic sensors for high precision detection of clear and transparent objects Clear object detection, inspection on transparent or highly reflective film and liquid level measurement Standard M18 tubular
ABSOLUTE OPTICAL ROTARY ENCODER MULTITURN BIT PARALLEL
Main Features - Compact and Heavy-Duty Industrial Model - Interface: Bit Parallel, Push Pull, Short Circuit Proof - Input: Preset (optional) and Latch - Housing: 58 mm - Shaft: 6 or 10 mm Hollow- 15 mm
The quadrature signals and the index pulse are accessed through five 0.025 inch square pins located on 0.1 inch centers.
Quick Assembly Two and Three Channel Optical Encoders Technical Data HEDM-550x/560x HEDS-550x/554x HEDS-560x/564x Features Two Channel Quadrature Output with Optional Index Pulse Quick and Easy Assembly
Harmonic Drive acutator P r e c i s i o n G e a r i n g & M o t i o n C o n t r o l
D C S e r v o S y s t e m s RH Mini Series Total Motion Control Harmonic Drive acutator P r e c i s i o n G e a r i n g & M o t i o n C o n t r o l Precision Gearing & Motion Control DC SERVO ACTUATORS
PD30ETB20xxIS. Photoelectrics, Background Suppression reflective with IR light. Main features. Description
Photoelectrics, Background Suppression reflective with IR light Main features Description The PD30ET... stainless steel sensors are built with high-quality materials and designed for harsh environments.
PLUTO Safety-PLC. Manual Absolute Encoders
PLUTO Safety-PLC Manual Absolute Encoders English v6a 2TLC172006M0206_A Table of contents: 1 General... 3 1.1 Reaction time... 3 1.2 Safety parameters... 3 2 Electrical... 4 2.1 Separation with Gateway
Magnetic proximity switches
Magnetic proximity switches Magnetic proximity switches Overview Page 38 Functional principle and installation Page 39 Cylindrical designs Page 41 Rectangular designs Page 42 37 Kurzübersicht Magnetoresistive
Three Channel Optical Incremental Encoder Modules Technical Data
Three Channel Optical Incremental Encoder Modules Technical Data HEDS-9040 HEDS-9140 Features Two Channel Quadrature Output with Index Pulse Resolution Up to 2000 CPR Counts Per Revolution Low Cost Easy
Multifunction devices
devices devices devices, electronic Type Page LED multifunction displays pulse, frequency, time (DC) Codix 524 240 pulse, frequency, time (AC+DC) Codix 544 243 LCD multifunction preset counters 1 or 2
Sturdy aluminium housing, anodized in blue Female connector for optical fiber (please order optical fiber separately) Mounting holes
SI-COLO Series SI-COLO2-LWL-HAMP-COL4 - Big measuring range: typ. 25 mm... 40 mm (with optical fiber and attachment optics KL-14 or KL-17) - Large assortment of optical fibers available (reflected or transmitted
sensors Miniature Sensors - S100 The universal miniature photoelectric sensor
Miniature Sensors - S1 The universal miniature photoelectric sensor Two threaded front mounting holes Two slotted rear mounting holes Anti-tampering sensor (no adjustment) Standard optic functions and
DSD 70 Dual Channel Hall Effect Speed Sensor for Railway Applications, compliant with EN 50155
DSD 70 Dual Channel Hall Effect Speed Sensor for Railway Applications, compliant with EN 50155 Technical information Version: 07.14 General Function The speed sensors family DSD.70 are suitable for generating
Servo Info and Centering
Info and Centering A servo is a mechanical motorized device that can be instructed to move the output shaft attached to a servo wheel or arm to a specified position. Inside the servo box is a DC motor
AFS60: Absolute Encoders Single turn, SSI AFM60: Absolute Encoders Multiturn, SSI und SSI + Incremental
Data heet : bsolute ncoders ingle turn, I : bsolute ncoders ultiturn, I und I + Incremental up to 18 bits bsolute ncoders ingleturn up to 3 bits bsolute ncoders ultiturn Number of lines 1 up to 5,53 Incremental
Technical data. General specifications. Indicators/operating means. 30 Hz Multiplex operation 30 Hz / n, n = number of sensors, n 5
Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service program ULTRA 000 programmable switch outputs Hysteresis
SENSORS. Miniature Sensors - S3Z. Advanced line of miniature Asian style of photoelectric sensors. 40-300 mm background suppression
Advanced line of miniature Asian style of photoelectric sensors 4-3 background suppression.7 m proximity, 15 with narrow beam 4 m polarized retroreflective 3 m LASER through beam Standard 3-wire output
Preset Counter signo 721
Most simple handling Impressive, clearly readable display in 48x48 mm Input frequency up to 60 khz Easy installation due to pluggable terminals TECHNICAL DATA GENERAL Display Height of digits Supply voltage
OPERATING MANUAL. Table of contents. 2 Phase Stepping Motor Driver 2M542. Rev. A. Introduction page 2. Specifications page 2 Timing chart page 3
2 Phase Stepping Motor Driver 2M542 OPEATING MANUAL Table of contents Introduction page 2 Specifications page 2 Timing chart page 3 Setting page 4 Current set page 4 educe current function page 4 Micro
D.C. Motors. Products and specifications subject to change without notice.
D.C. Motors Order/Technical Support - Tel: (8) 677-5 / FAX: (8) 677-865 / www.crouzet-usa.com / DC Motors Selection guide Gearbox Speed Torque max (Nm).5. Type of Gearbox 8 8 8. Power usable (w) Torque
HSP GmbH Zum Handwerkerhof 2 90530 Wendelstein Tel. 09129 / 2852-0 Fax: 09129 / 2852-11 Web: www.hsshsp.de EMAIL: HSP@hsshsp.de NTG-3000.
NTG-3000 Transducer Data Sheet Document Version 2.8 Page 1 of 10 Versions / Revisions: Document Creation Author Description version date 2.0 2012-07-25 P. Compensis First official version 2.1 2012-08-24
Inductive sensor NI10-M18-Y1X-H1141
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Threaded barrel, M18 x 1 Chrome-plated brass DC 2-wire, nom. 8.2 VDC Output acc. to DIN EN 60947-5-6 (NA- MUR) M12
Datasheet of the Easy Servo Motor ES-M Series
Datasheet of the Easy Servo Motor ES-M Series Stepper Motor with Encoder, 0.9-8 Nm Version 1.3 http://www.leadshine.com Descriptions Leadshine s ES-M series easy servo motors, or stepper motors with encoders,
Givare NC-SRS 280 och 880
Givare NC-SRS 280 och 880 Aratron AB/Nordic Control, 02 03 SRS280SEALED ROTARY SENSOR PERFORMANCE ±2 Resistance ±20% Hysteresis (repeatability) Accuracy Applied voltage maximum Resolution Output smoothness
Series LC6D/LC6C. To power supply PLC. LC6C dedicated teaching box P.971. Options P.973
Series LCD To power supply Electric Actuator Series LCC Stepper Motor Driver LCD Series LX Dedicated Stepper Motor Driver and Positioning Driver Series LCD/LCC PLC Positioning unit (Not incl. To be provided
Agilent AEDB-9140 Series Three Channel Optical Incremental Encoder Modules with Codewheel, 100 CPR to 500 CPR Data Sheet
Agilent AEDB-9140 Series Three Channel Optical Incremental Encoder Modules with Codewheel, 100 CPR to 500 CPR Data Sheet Description The AEDB-9140 series are three channel optical incremental encoder modules
Datasheet of the Easy Servo Motor ES-MH Series
Datasheet of the Easy Servo Motor ES-MH Series High Voltage Stepper Motor with Encoder, 8-20 Nm Version 1.4 http://www.leadshine.com Descriptions Leadshine s ES-MH series easy servo motors, or stepping
Absolute encoders multiturn
bsolute encoders multiturn Sendix / (shaft / hollow shaft) thernet / IP The Sendix multiturn with patented Intelligent Scan Technology is a particularly high resolution optical encoder without gears and
AUTOMATICOS S.L OPTICAL ENCODERS
OPTICAL ENCODERS FACTORY AND OFFICES Prolongación c/ Sant Francesc s/n 17400 Breda (Girona) España Tel.: (00 34) 972 160 017 Fax: (00 34) 972 160 230 E-mail: info@hohner.es Web: www.hohner.es TO FRANCE
Magnetic field sensor for pneumatic cylinders BIM-INT-Y1X-H1141
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Rectangular, height 6mm Plastic, PA12 Magnetic-inductive sensor DC 2-wire, nom. 8.2 VDC Output acc. to DIN EN 60947-5-6
ABB Drives. User s Manual HTL Encoder Interface FEN-31
ABB Drives User s Manual HTL Encoder Interface FEN-31 HTL Encoder Interface FEN-31 User s Manual 3AUA0000031044 Rev B EN EFFECTIVE: 2010-04-06 2010 ABB Oy. All Rights Reserved. 5 Safety instructions
ABB Drives. User s Manual. Pulse Encoder Interface Module RTAC-01
ABB Drives User s Manual Pulse Encoder Interface Module RTAC-0 Pulse Encoder Interface Module RTAC-0 User s Manual 3AFE 64486853 REV A EN EFFECTIVE:.5.00 00 ABB Oy. All Rights Reserved. Safety instructions
Laser diffuse reflection light scanner with background suppression. Dimensioned drawing
Specifications and description HRTL 3B Laser diffuse reflection light scanner with background suppression Dimensioned drawing We reserve the right to make changes DS_HRTL3B_en.fm en 01-2010/12 50114049
TECHNICAL DATASHEET #TD1404AX PWM CONTROLLED SOLENOID DRIVER
TECHNICAL DATASHEET #TD1404AX PWM CONTROLLED SOLENOID DRIVER (PWM Input, 1.2A or 2A Output, Metal Box or PCB) PCB Board - P/N: PWMC-PCB-2A, PWMC-PCB-1.2A Packaged Driver (metal box with 1.5 m (5 ft.) cable)
VP23, 3-way proportional pressure control valves Seat valve with μp-driven pressure control
VP, -way proportional pressure control valves > > Port size: G/... G/ > > All-digital control electronics > > Variable pressure control > > Optional actuation via fieldbus (separate datasheet on request)
Actuators and positioning drives
Actuators and positioning drives distributed by www.laumans.com Actuators and positioning drives FlexiDrive product range type MDBA 42 MSQA 46 MSAA 42 Actuator Actuator Actuator motor brush DC motor brush
Speed sensor MiniCoder GEL 247
Speed sensor MiniCoder GEL 47 Flange assembly Technical information version 08.0 The MiniCoder family from Lenord + Bauer offers spacesaving solutions for the contactless measurement of rotational movements
I nstallation. M100Q Series Proportional Actuator with R81Q Controller Board for Thermistor Sensor Applications. Tools Needed.
FANs 268.1, 1628.3 Installation Bulletin M100Q Issue Date 1099 M100Q Series Proportional Actuator with R81Q Controller Board for Thermistor Sensor Applications I nstallation Parts Included M110QGA-1 and
W150: Miniature photoelectric switch series with completely integrated electronics
Product group W50 Photoelectric proximity switch BGS Photoelectric proximity switch energ. Photoelectric reflex switch W50: iniature photoelectric switch series with completely integrated electronics Through-beam
Operating instructions
Operating instructions Torque transducer type AE with replaceable strain gauge measuring element Model TQ 505 Operating instructions no. 1079 Torque Transducer TQ 505 Page 1 / 16 1. Contents 1. List of
DRS61: Incremental encoders, number of lines and zero pulse width freely programmable DRS60: Incremental Encoders with Zero-Pulse-Teach
RS: Incremental encoders, number of lines and zero pulse width freely programmable RS: Incremental Encoders with Zero-Pulse-Teach Further highlights of this generation of encoders: Simple zero-pulse-teach
Mounting Instructions. Torque Transducer. A0329 3.2 en
Mounting Instructions Torque Transducer T5 T5 Contents 3 Page Safety instructions.............................................. 4 1 Measuring characteristics..................................... 7 2 Mounting.....................................................
TM7BDM8B expansion block - TM7 - IP67-8 DI/DO - 24V DC - 0.5 A - M8 connector
Product datasheet Characteristics TM7BDM8B expansion block - TM7 - IP67-8 DI/DO - 24V DC - 0.5 A - M8 connector Main Range of product Product or component type Range compatibility Enclosure material Bus
Subminiature Load Cell Model 8417
w Technical Product Information Subminiature Load Cell 1. Introduction... 2 2. Preparing for use... 2 2.1 Unpacking... 2 2.2 Using the instrument for the first time... 2 2.3 Grounding and potential connection...
Technical data. General specifications. Indicators/operating means. Electrical specifications Operating voltage U B Power consumption P 0 Interface
Release date: 06-0- 09: Date of issue: 06-0- 009_eng.xml Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service
Pressure transmitter For general industrial applications Model A-10
Electronic pressure measurement Pressure transmitter For general industrial applications Model A-10 WIKA data sheet PE 81.60 for further approvals see page 9 Applications Machine building Shipbuilding
CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version)
TECHNICAL DATASHEET #TD1102AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version) Part Number: Connector Amplifier CAPV-H-4-20MA-x complete with cable CAPV-4C-yM Where: x = current output
Encoders. the incremental encoders format such as relective optical technology, transmissive optical technology
the incremental encoders format such as relective optical technology, transmissive optical technology back devices, brakes and gearboxes at no extra cost to you. USA: +1 267 933 2105 Europe: +33 20928751
Product Information. HMC 6 Hybrid Motor Cable
Product Information HMC 6 Hybrid Motor Cable November 2014 HMC 6 Single-cable solution for servo drives Motors normally need two separate cables: One cable for the motor encoder One cable for the motor
LVDT. Inductive Position Transducer. SM Series. Key-Features:
LVDT Inductive Position Transducer SM Series Key-Features: Content: - Measurement ranges 2...200 mm - External, or cable electronics with cable break detection - Linearity up to ±0.10 % of full scale -
Delivering solutions. Since 1985 Eltra is present in the market of encoders and industrial automation both nationally and in foreign Countries.
Delivering solutions Since 1985 Eltra is present in the market of encoders and industrial automation both nationally and in foreign Countries. During these years the company constantly grew extending its
Cable Plug acc. to DIN EN 175301-803, Form A
Cable Plug acc. to DIN EN 175301-803, Form A Complete program Contact form 18 mm Also available with LED indicator Optional 4-pin version for pressure switch or impulse valves respectively Versions with
330450 High Temperature Acceleration System Bently Nevada* Asset Condition Monitoring
330450 High Temperature Acceleration System Bently Nevada* Asset Condition Monitoring Description The standard 330400 Accelerometer has a limited temperature range it can be exposed to, due to its signal
0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N
55 Series - General purpose relays 7-10 A Features 55.12 55.13 55.14 Printed circuit mount, general purpose 2, 3 & 4 Pole relays 55.12-2 Pole 10 A 55.13-3 Pole 10 A 55.14-4 Pole 7 A AC coils & DC coils
Electronic Pressure Switch EDS 300
Electronic Pressure Switch EDS 300 User manual Page 2 of 16 Content 1. Functions of the EDS 300...3 2. Mounting...3 3. Operating keys on the membrane keypad...4 4. Digital display...4 5. Output function...5
SPEED CONTROL SYSTEM
SPEED CONTROL SYSTEM INDEX SPEED CONTROL MOTOR FEATURES 144 6W ( 70mm) 153 10W ( 70mm) 155 15W ( 80mm) 157 25W ( 80mm) 159 40W ( 90mm) 161 SPEED CONTROL W ( 90mm) 163 90W ( 90mm) 165 120W ( 90mm) 168 180W
Siemens AG 2011 SINAMICS V60. The perfect solution for basic servo applications. Brochure May 2011 SINAMICS. Answers for industry.
The perfect solution for basic servo applications Brochure May 2011 SINAMICS Answers for industry. with 1FL5 servomotors The solution for basic servo applications There is a requirement to automate motion
Resolution (divisions) Pre-wired Model E6F-AB3C 360P/R 2M *2 Pre-wired Connector E6F-AB3C-C 360P/R 2M *2 Model (2 m) NPN open collector BCD 360
Absolute 60-mm-dia. Rotary Encoder CSM DS_E_7_ Rugged Rotary Encoder Absolute model. External diameter of 60 mm. Resolution of up to 1,024 (10-bit). IP65 oil-proof protection. Strong shaft. Radial: 120
How To Read A Pipe From A Sensor
Liquid Level Sensor Installation on pipes. Sensing by means electrostatic capacity and is not influenced by the color of the pipe or liquid. Available in 8 to mm dia. and to mm dia. models to enable sensing
Type: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
RM35UA13MW. range 15..600 V. Main. Product or component type. Relay monitored parameters
Characteristics multifunction voltage control relay RM35-U - range 15..600 V Complementary Reset time Maximum switching voltage [Us] rated supply voltage Supply voltage limits Power consumption in W Main
Part number NPN E2EM-X2C1 E2EM-X2C2 PNP E2EM-X2B1 E2EM-X2B2 NPN E2EM-X4C1 E2EM-X4C2 PNP E2EM-X4B1 E2EM-X4B2
R Extended Range Inductive Prox Greater Sensing Distance Offers Greater Design Flexibility H Sensing distances approximately 1.5 to 2 times larger than that of any conventional Sensor H Reduces problems
RM17TE 183...528 V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC
Characteristics multifunction control relay RM17-TE - range 183..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
3-PHASE STEPPING MOTOR. VRDM 39x. Document: 100000116 Edition: d013, 2005.02
-PHASE STEPPING MOTOR VRDM 9x Edition: d, 5. Features common to all motor types Test voltage to DIN EN 64 part Insulation class F Run-out and perpendicularity to DIN 4955 N Paint: black RAL 95 Security
Incremental rotary encoders measure pulses per revolution
Product Bulletin Incremental rotary encoders measure pulses per revolution Reliable position detection using optical technology For applications in material handling, packaging, robotics, and metalworking