ATS-8000 TABBER QUICK START INSTRUCTIONS / PARTS CATALOG

Size: px

Start display at page:

Download "ATS-8000 TABBER QUICK START INSTRUCTIONS / PARTS CATALOG"

Mae Pearson
7 years ago
Views:

1 ATS-8000 TABBER QUICK START INSTRUCTIONS / PARTS CATALOG

2 SAFETY PRECAUTIONS THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. HOWEVER, CERTAIN SAFETY RULES SHOULD BE OBSERVED WHEN OPERATING THE ATS-8000 READ THIS MANUAL CAREFULLY AND FOLLOW THE RECOMMENDED PROCEDURES: 1. Keep hands, hair, and clothing clear of rollers and other moving parts. 2. Always turn off machine before making adjustments, cleaning the machine, or performing any maintenance not covered in this manual. 3. Turn power off when not in use. MODEL ATS-8000 TABBER DIMENSIONS: SPEED: MEDIA SIZE: MEDIA THICKNESS: 1/8. TAB SIZE: LABEL SENSITIVITY CONTROL: REEL CAPACITY: COUNTER: FEEDER: SHIPPING WEIGHT: ELECTRICAL: CAUTION THIS EQUIPMENT MUST BE CONNECTED TO A PROPERLY GROUNDED OUTLET. FAILURE TO DO SO CAN CAUSE ELECTRIC SHOCK! SPECIFICATIONS 21 3/4 W x 19 1/2 H x 8 1/2 L Fixed speed 12,000 per hour (8 1/2 x 11 tri-folds) Length - 3 min., 18 max. Width 5 min., 17 max. LENGTH 5/8 TO 1 1/4 (standard tabs) Adjusts for density in tab/wafer seals. 5,000 tabs 5 digit LCD Top load, bottom feed for continuous operation 44 lbs. 110V, 50/60Hz, 1 AMP 220V, 50/60Hz,.5 AMP OPTIONAL MODEL ALS-900 CONVEYOR DELIVERY DIMENSIONS: SPEED: ELECTRICAL: SHIPPING WEIGHT: 11.5 x 18 L x 4 H Variable inches per minute 110 VAC 60 Hz, 0.5 Amp (220 VAC 50/60 Hz available) 16 lbs / 7.5 kg

3 ATS-8000 QUICK-START INSTALLATION SETTING UP AS A STAND-ALONE TABBER 1. Remove all packing and parts supplied. Check and identify all parts with the ones listed below. MEDIA GUIDES STACK REST MEDIA SUPPORT THUMBSCREWS TRACK ROLLER ASSEMBLY (4 ROLLER) (2 ROLLER) METERING BRACKET ASSEMBLY Attach MEDIA GUIDES (Fig. 2). 3. Install METERING BRACKET ASSEMBLY (Fig. 1,2, and 2A). 4. Install TRACK ROLLERS [2 ROLLER] (Fig. 2). 5. Install MEDIA SUPPORTS and STACK RESTE (Fig. 2). Figure 1 METERING BRACKET ASSEMBLY Figure 2-1-

4 Figure 2A SETTING UPS AS IN-LINE TABBER 1. Remove MEDIA GUIDES (Fig. 2 and 2A). 2. Remove METERING BRACEKT ASSEMBLY (Fig. 1,2, and 2A). 3. Remove MEDIA SUPPORTS (Fig. 2.) 4. Remove TRACK ROLLERS [2 roller] (Fig. 2). 5. Install TRACK ROLLERS [4 roller] (Fig. 3 and 4). Figure 3 TRACK ROLLERS (4 ROLLER)

5 LOADING TABS OPERATING INSTRUCTIONS 1. Remove TAB ROLL SIDE GUIDE (Fig.5). Figure 4 Figure 5-3-

6 2. Place roll of tabs on SPINDLE (Fig. 5A). 3. Reinstall TAB ROLL SIDE GUIDE. 4. Remove approximately 10 of tabs from backing paper. 5. Remove EXIT ROLLER (Fig. 5). 6. Thread tab stock behind REEL ASSEMBLY BRAKE ROLLER (fig. 5) and in front of IDLER ROLLER (Fig. 5). 7. Thread tab stock through BLACK PLASTIC SENSOR HOLDER (fig. 5A) until stock exits the front for the machine. Bend backing paper and thread it through metal lip (Fig. 5B) until it touches ABRASIVE ROLLER (Fig. 5A). 8. With LABEL PRESSURE KNOB ON, use LABEL ADVANCE KNOB (Fig. 5) to advance tabs until tab begins to peel. 9. Bring TAB ROLL SIDE GUIDE into place. 10. Place backing paper into TAKE-UP REEL (Fig. 5A). Figure 5A Figure 5B -4-

7 SETTING TAB SENSITIVITY ADJUSTMENT 1. With tab exposed, turn power switch to ON. 2. Turn knob on rear of machine all the way counterclockwise (A, Fig. 6). Now turn one click at a time clockwise until the LED (B, Fig. 6) comes on. 3. Turn LABEL PRESSURE (Fig. 5) OFF and roll tabs backward until just backing paper is visible in sensor holder. Turn one click at a time clockwise until LED comes on. Counting the clicks, turn counterclockwise half the number that you just counted. (Example: the LED illuminates for the first time at position four and a second time at position 10. The difference between the two positions is six clicks. Turn back half that number or 3 clicks to position 7). NOTE: If adjusting know exceeds number of positions on switch without illuminating LED, then proceed as it were illuminated. If you have an odd number difference, (for example 7 clicks then begin with the lowest number, 3. If double tabbing occurs then click one more time to four). 4. With LABEL PRESURE ON, use LABEL ADVANCE KNOB (Fig. 5) to advance until tab starts to peel away from backing paper. 5. Reinstall EXIT ROLLER. Figure 6-5-

8 USING AS STAND-ALONE TABBER 1. Set up stand-alone tabber. 2. Position mail piece side to side where tab is desired. 3. Slide MEDIA GUIDES (Fig. 2A) into place. 4. Position STACK RESTS (Fig. 2) under mail piece. Position MEDIA AUPPORTS (Fig. 2) so that back edge of mail piece is in the middle of the support. 5. Place one mail piece on feed roller so that the plastic separators are over the piece. Loosen thumbscrews so tips fall on the mail piece. Tighten thumbscrews. 6. Push tab button down followed by feed button. Check position of tab side to side. Adjust if necessary by moving side guides. 7. Run one more mail piece through then check the tab position top to bottom. Adjust if necessary with thumbscrew under and to the right of the LABEL ADVANCE KNOB (Fig. 2). 8. You are ready to start tabbing. USING AS IN-LINE TABBER 1. Set us as in-line tabber. 2. Position in-line tabber next to machine you are using. To adjust side-to-side position, move either tabber or other machine. OPERATING HINTS 1. Fan out the media before use. 2. After loading the media, tap the stack lightly to keep it straight between the guides. 3. If doubles occur, check the stripping device for proper pressure setting. 4. Straighten out excessively curled media. CONTROL PANEL FUNCTIONS A. ON-OFF Power Switch B. Fuse 2 AMP 250V C. Counter (Press RED button to reset) D. Tab Feed ON/OFF E. Media Feed ON/OFF Front of Machine Top of Machine -6-

9 -7- GROUP 1

10 KEY# PART # DESCRIPTION QTY. KEY# PART # DESCRIPTION QTY SCREW, 8-32 X 5/16 PH. HD CLUTCH ASSY SIDE GUIDE, REEL ROLL PIN 1/8 X 3/ O-RING, LUTZ #107-B46A CLUTCH SHAFT SUPPORT HUB, REEL HOUSING ASSY, BALL BEARING TRUARC, # 5133 X0025SP SCREW, 6-32 X 1/4 FLAT PH HOLD DOWN STACKER WHEEL SIDE FRAME COVER RIGHT SCREW, BUTN. HD. PH X1/ TIMING BELT 160 XL037B SCREW, TRUSS HD. PH X 1/ ROLLER ASSY., TENSIONER SCREW, X 1/4 UNDERCUT PIVOT REEL LINK ASSY SET SCREW, X 3/ SCREW, 6-32 X 1/4 PAN HEAD MOTOR PULLEY ASSY, 26TEETH WASHER, # SCREW, SOC. HD X 5/ SPRING, PRESSURE ROLLER WASHER, PLAIN # PIVOT, REEL WASHER, 9/32 X 3/4 X/1/16 PLASTIC WASHER, #6 STAR MOTOR ASSEMBLY SCREW, TRUSS HD. PH X 3/ ARM ASSY STUD, SPOOL SUPPORT SET-SCREW, 8-32 X 1/ REEL BRAKE SPRING ROLLER, TAKE-UP PRESSURE SPACER, REEL ARM ASSY ARM ASSY., REEL PIN SCREW, 6-32 X 5/16 PH. FLT-HD SPRING, PRESSURE ROLLER E STAND ASSY., REEL SCREW, X 5/16 SOCKET CAP ROLLER SHAFT, REEL WELDMENT, PAPER TAKE-UP SHAFT PLASTIC ROLLER E WELDMENT, APPLICATOR HEAD KNOB ASSY WELDMENT, MEDIA SENSOR BRACKET TAB GUIDE THUMBSCREW ASSY ROLLER TAB GUIDE HOUSING, BALL BEARING ASSY APPLICATOR HEAD ROD KNOB, TAB ADVANCE APPLICATOR HEAD SUPPORT WELDMENT, TAB SEPARATOR HEAD SUPPORT COVER W/SILK SCREEN SCREW, 6-32 FL. HD. W/UNDERCUT TAB PULL ROLLER ASSY HOLDER ASSY. R/H, APPL. ROLLER BRAKE ASSEMBLY STUD, APPLICATOR ROLLER ROLL PIN X 3/ LABEL SENSOR ASSY. FOR ATS SCREW, 1/4-28 X 1/4 SOCKET HD. CAP SPRING, TAB GUIDE WELDMENT HOUSING-BALL BEARING ROLLER, APPLICATOR HEAD CLUTCH COUPLING ASSY SPRING 2 GROUP 1-8-

11 KEY# PART # DESCRIPTION QTY. KEY# PART # DESCRIPTION QTY SCREW, 6-32 X 5/8 HEX HD DRIVE SHAFT WELDMENT, CENTER PLATE WELDMENT, SIDE GUIDE R/H TRACK ROLLER SPRING WLEDMENT REAR FEED SHAFT ROLLER SCREW, FH X 3/ SHAFT, TRACK ROLLER METERING BRACKET TRUACR, # METERING SEGMENT SCREW, PH. RD. HD X 3/ BEAM, REAR SUPPORT RETAINER SPRING ASSY FEED ROLLER THUMBSCREW, METERING BRACKET KNOB ASSY SPRING, RETAINER BLOCK, SIDE GUIDE ROLLER, FRONT FEED SCREW, X 1/4 ROUND HEAD PULLEY, 12 XL WELDMENT, SIDE GUIDE L/H ROLL-PIN, 3/32 X 5/ SIDE FRAME LEFT WASHER, 1/4 X 1/2 X 1/ FOOT, RUBBER #70 ASHORA RELEASE, ECCENTRIC E MOTOR BASE SPRING-PIN, 3/32 X 1/ REAR ENVELOPE SUPPORT WELDMENT SHAFT, RELEASE ECCENTRIC WELDMENT, REAR CLOSURE BELT, 80 XL PAPER STACK REST WELDMENT PULLEY, 14 TEETH E SIDE FRAME RIGHT SET-SCREW, X 3/ E SLEEVE O-RING,.125 X REAR FEED SHAFT ASSY SPOOL, PAPER TAKE-UP DRIVE SHAFT ASSY PULLEY, 20 TEETH ROLLER ASSY., FRONT FEED STUD, IDLER PULLEY SIDE GUIDE ASSY., REEL BELT, TIMING 90 XL HOLDER ASSY., APPLICATOR ROLLER L/H PULLEY, DRIVE SHAFT APPLICATOR HEAD ROD DRIVE PULLEY ASSY SCREW, 10-24X1/4 SOC PT RUBBER FEED ROLLER ASSY ASSEMBLY, FOUR TRACK ROLLER 1 GROUP 1-9-

12 -10- GROUP 2

13 KEY# PART NUMBER DESCRIPTION QTY. KEY# PART NUMBER DESCRIPTION QTY COUNTER ASSY WIRE HARNESS, POWER SWITCH SWITCH FEED/TAB FUSE, 2A/250V WIRE HARNESS SWITCHES FUSE HOLDER LABEL SENSOR ASSY. FOR ATS JUMPER, TERMINAL BLOCK SCREW, 6-32 X 5/16 PH. FLT-HD JUMPER, TERMINAL BLOCK SNAP-IN BUSHING, OD TERMINAL BLOCK, 6 TERMINALS CLUTCH ASSEMB LY SCREW, 6-32 X 3/ CABLE HOLDER TRANSFORMER ASSY BRAKE ASSEMBLY SUPPORT, CIRCUIT BOARD MOTOR ASSEMBLY FUSE, 1/2 A - 5X20 MM CABLE HOLDER 1/4 IN POWER SUPPLY BOARD WIRE HARNESS - MOTOR WIRE HARNESS - POWER SUPPLY TIE, PLASTIC CONTROLLER BOARD WIRE HARNESS, MEDIA SENSOR WIRE HARNESS SET-UP SWITCH WASHER, STAR # SET-UP SWITCH ASSY SCREW, BTN. HD PHIL 4-40 X 1/ LED HOLDER STRAIN RELIEF DECAL, SENSOR ADJUSTMENT SWITCH POWER CORD, 6 FT KNOB, SPEED CONTROL WASHER, STAR # DECAL, SENSOR ADJUSTMENT INSTR SCREW, TRUSS HD. PHIL X 1/ WIRE HARNESS, COUNTER EXTENSION SWITCH, MAIN POWER 1 GROUP 2-11-

14 INDEX PART # KEY GROUP PART # KEY GROUP PART # KEY GROUP E E E E E

15 INDEX PART# KEY GROUP

SE-1200-EI. Operation & Parts Manual

SE-1200-EI. Operation & Parts Manual SE-1200-EI Operation & Parts Manual SE 1200 EI OWNERS MANUAL Table of Contents 1. Installation guide 2. Set-up instructions 3. Operation instructions 4. Cleaning 5. Troubleshooting 6. Parts manual 7. Electrical