616 GSR Driftwood Log Set Installation Instructions (SKU )

Transcription

1 Compatibility 616 GSR Packing List 7 Piece Driftwood Log Set (not shown) Standoff Pack: Includes (4) Log Support Brackets, (6) Nuts Rear Burner Deflector, NG/LP Rear Air Deflector Bag of Rock Wool, Bag of Embers WARNINGS Make sure the gas control valve is OFF and the heater is cool before conducting service. Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. If using propane (LP), convert the appliance before installing the logs (see the owner s manual for details). Do not use crushed glass media with this log set. It causes excess sooting. Use included rock wool. Page 1 of docx 8/23/12 Travis Industries, Inc.

2 Burner Installation NOTE: The insert should be in place, with the gas line and vent attached, and the firebacks installed (see owner s manual for further details) before proceeding. 1. Remove the rear burner as shown below. NOTE: Remove the attachment screw first. 2. Remove the 3 screws from the back of the rear burner using a ¼ nutdriver. Page 2 of docx 8/23/12 Travis Industries, Inc.

3 3. Attach the rear air deflector to the rear burner with the screws removed in the previous step. NOTE: Verify the correct air deflector according to your fuel type IMPORTANT: Make sure the air deflector holes are aligned, if they do not align flip the deflector over. NG Installation This notch in the LP deflector differentiates it from the NG air deflector. LP Installation 4. Replace the rear burner and secure with the attachment screw. The two tabs on the rear burner rest on top of the front burner. Page 3 of docx 4/30/13 Travis Industries, Inc.

4 5. Install the rear burner deflector. 616 GSR Driftwood Log Set 6. Attach the log supports with the 6 included nuts. Page 4 of docx 8/23/12 Travis Industries, Inc.

5 Rock Wool Placement 7. Place the rock wool as follows: a. Brush the rock wool using a stiff brush in a loose, gauze like layer. TIP: Hold the rock wool in a tight wad with one hand while brushing with the other. Note how the rock wool is approximately 1/8 thick over the burner ports. TIP: Feel free to apply a generous amount of rock wool to gain a darker flame and a brighter coal bed. Page 5 of docx 8/23/12 Travis Industries, Inc.

6 Log and Ember Chunks Placement 616 GSR Driftwood Log Set The logs are fragile, especially after being exposed to heat. IMPORTANT: The burner must be correctly positioned before installing the logs. Make sure the burner is fully seated. 8. Place the rear log as shown below. Move the log forward until it rests against the tabs on the burners. Page 6 of docx 8/23/12 Travis Industries, Inc.

7 9. Place the left middle log. 10. Place the right middle log. Page 7 of docx 8/23/12 Travis Industries, Inc.

8 11. Place the left cross log. 12. Place the pilot log. Page 8 of docx 8/23/12 Travis Industries, Inc.

9 13. Place the front right log. 14. Place the center cross log. Page 9 of docx 8/23/12 Travis Industries, Inc.

10 15. Place the ember chunks. Note that roughly half the bag of embers is left over. Make sure that the ember chunks DO NOT cover any burner ports. TIP: The ember chunks should be placed so as to hide any sheet metal parts, rivets, and screws. 16. Re apply the rock wool over the ember chunks along the front burner and between the two front logs for a natural look. TIP: Natural gas (NG) can use more rock wool than propane (LP). NOTE: Initial application of rock wool may cause matting over burner ports. Turning the unit on and then off again will loosen the rock wool, resulting in a better flame. Page 10 of docx 8/23/12 Travis Industries, Inc.

11 17. Check the exhaust restrictor setting before finalizing the installation. Natural Gas Short Vent (25 or less) Natural Gas Tall Vent (25 or more) Propane Short Vent (25 or less) Propane Tall Vent (25 or more) Restrictor Settings Driftwood Logs #1 #3 (stock) #1 #3 (stock) Finalized installation: 18. Test burn the insert with the glass frame in place before finishing the installation. See the owner s manual for details on finalizing the installation (adjusting the air shutter, etc.). Page 11 of docx 8/23/12 Travis Industries, Inc.