Freestanding Lace Haunted House #12480 / 15 Files / 1 Design

Transcription

1 #12480 / 15 Files / 1 Design It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

2 #12480 / 15 Files / 1 Design Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen Haunted Front Door Wall 2.86 X 6.98 in X mm 23,167 St. zr L Haunted Right Wall 6.02 X 4.38 in X mm 32,102 St. zr L Haunted Back Wall 2.86 X 7.00 in X mm 11,512 St. R L Haunted Inner Wall 6.04 X 4.77 in X mm 41,654 St. zr L Haunted Roof X 4.43 in X mm 29,072 St. zr L Haunted Roof X 3.73 in X mm 29,147 St. zr L Haunted Front Wall 4.76 X 4.37 in X mm 28,236 St. zr Haunted Left Wall 4.77 X 5.87 in X mm 37,807 St. zr L Haunted Back Door Wall 4.74 X 4.17 in X mm 22,041 St. zr Haunted Roof X 3.61 in X mm 20,911 St. zr L Haunted Roof X 3.79 in X mm 21,190 St. zr L Haunted Upper Room 6.81 X 3.98 in X mm 19,466 St. zr L It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

3 #12480 / 15 Files / 1 Design Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen Haunted Roof X 4.85 in X mm 21,482 St. zr Haunted Foundation X 6.15 in X mm 9,231 St. R L Haunted Foundation X 4.53 in X mm 12,076 St. R It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

4 Listings below indicate color sample, stitching order and suggested thread color number. I refers to Isacord Thread and T refers to Timeless. Colors beginning with refer to YLI Fine Metallics, 7 refer to Yenmet Metallic, 8 refer to YLI Variations Variegated Thread and 9 refer to Isacord Multicolor Variegated Haunted Front Door Wall n 3. Door Placement Stitch n 4. Door Cut Line & Tackdown n 5. Windows Placement Stitch n 6. Windows Cut Line & Tackdown Haunted Right Wall n 3. Ghost Placement Stitch n 4. Ghost Cut Line & Tackdown n 5. Windows Placement Stitch n 6. Windows Cut Line & Tackdown Haunted Back Wall Haunted Inner Wall Haunted Roof 1 n 1. Roof Placement Stitch n 2. Roof Cut Line & Tackdown I T I T I T Haunted Roof Haunted Roof 4 n 1. Roof Placement Stitch n 1. Roof Placement Stitch n 2. Roof Cut Line & Tackdown n 2. Roof Cut Line & Tackdown Haunted Front Wall n 3. Window Placement Stitch n 4. Window Cut Line & Tackdown n 5. Lace Haunted Left Wall n 3. Door Placement Stitch n 4. Door Cut Line & Tackdown n 5. Window Placement Stitch n 6. Window Cut Line & Tackdown Haunted Back Door Wall n 3. Door Placement Stitch n 4. Door Cut Line & Tackdown n 5. Window Placement Stitch n 6. Window Cut Line & Tackdown Haunted Roof 3 n 1. Roof Placement Stitch n 2. Roof Cut Line & Tackdown Haunted Upper Room n 1. Tall Walls Placement Stitch n 2. Tall Walls Cut Line & Tackdown n 3. Short Walls Placement Stitch n 4. Short Walls Cut Line & Tackdown n 5. Window Placement Stitch n 6. Window Cut Line & Tackdown Haunted Roof 5 n 1. Roof Placement Stitch n 2. Long Side Cut Line & Tackdown n 3. Short Side Cut Line & Tackdown n 4. Lace Haunted Foundation 1 n 1. Floor Placement Stitch n 2. Floor Cut Line & Tackdown Haunted Foundation 2 n 1. Floor Placement Stitch n 2. Floor Cut Line & Tackdown Cut in Place 1. Hoop your fabric and backing. 2. Sew the pattern/placement. PHOTO 1 3. Place a piece of appliqué fabric over the pattern/placement so that it is completely covered. 4. Sew the trim stitch/tackdown. 5. Carefully cut away the excess appliqué fabric.photo 2 6. Sew the remainder of the design and repeat for any remaining pieces. PHOTO

5 GENERAL FREESTANDING LACE GUIDELINES SUPPLIES: Embroidery Thread: Use the same embroidery thread in the bobbin as the needle. Needles: Use an Organ 80/12 Titanium needle for extended needle life. Stablilizer: Use water-soluable stabilizer or film water-soluble stabilizer. GENERAL INSTRUCTIONS 1. Hoop two layers of water-soluble stabilizer. 2. Attach the hoop to the machine and select the design of your choice. 3. Stitch the design. 4. Remove the hoop from the machine and the design from the hoop. Trim excess stabilizer from the design. 5. Rinse away remaining stabilizer and allow it to dry. HANDY HINTS: DO NOT RINSE away all of the stabilizer for a stiffer lace. Note that the thread may appear a shade darker if stabilizer is not removed completely. If you happen to wash too much out, easily re-stiffen by diluting some stabilizer scraps in water and dipping the item in the solution. Drying Lace: Lay lace piece with right side down to dry. This will minimize the tendancy for the lace to curl. Handy tips: A pair of tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (Please see Diagram 1 for explanation of buttonette and eyelet and hinge line.) Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. A stiletto could be used to push the buttonette through the eyelet. The lace looks best when left to dry completely. Be sure to flatten the piece out entirely and allow ample time to dry. If item becomes too limp to work with, dissolve scrap pieces of water-soluble stabilizer in warm water and apply to the item to re-stiffen. Alternatively you can iron the appliqué pieces on the wrong side while applying spray starch. After ironing, spray again with starch and allow to dry completely. This will stiffen the lace pieces nicely and aid in construction. Diagram 1

6 Haunted House - Summary Requires 1 FSL Haunted Front Door Wall Requires 1 FSL Haunted Right Wall Requires 1 FSL Haunted Back Wall Requires 1 FSL Haunted Inner Wall Requires 1 FSL Haunted Roof Requires 1 FSL Haunted Roof Requires 1 FSL Haunted Front Wall Requires 1 FSL Haunted Left Wall Requires 1 FSL Haunted Back Door Wall Requires 1 FSL Haunted Roof Requires 1 FSL Haunted Roof Requires 1 FSL Haunted Upper Room Requires 1 FSL Haunted Roof Requires 1 FSL Haunted Foundation Requires 1 FSL Haunted Foundation Supplies Embroidery thread Fabric for appliqué (We used: deep purple for the walls, gold organza for the windows, light charcoal for roof & light grey for the doors.) Embroidery machine Stabilizer Optional - tweezers, hemostats, stiletto or a tiny crochet hook Freestanding Lace Haunted House for Haunted House Construction Note that the base of the building has a hole meant to contain a battery operated tea light candle. Follow the General Freestanding Lace Guidelines and Cut In Place and stitch the fifteen pieces required as listed in the summary above. Build Upper Room Structure 1. Connect right wall of the Upper Room with the back wall of the Upper Room. Photo 1 2. Attach Roof 5 to the Upper Room walls attach long side of roof to long slant on Upper Room and short side to the short slant. Photo 2 Set aside built upper room structure Build Left Roof Structure 3. Connect edge of Roof 3 to Roof 4. Photo 3 Photo 1 Photo 2 Photo 3 Photo 4 Connect Upper Room Structure to Left Roof Structure 4. Connect front of the upper room structure (with window) into the two eyelets on Roof 3. Photo 4

7 5. Connect back of the upper room structure into the two eyelets on Roof 4. Set aside built upper room & left roof structure Build Right Room Structure 6. Connect left edge of Front Door Wall to the right edge of the Inner Wall. 7. Connect right edge of Front Door Wall to the left edge of Right Wall. Photo 5 8. Connect right edge of Back Wall to left edge of the Inner Wall. Set aside built right room structure Photo 5 Photo 6 Build Right Roof Structure 9. Connect edge of Roof 1 to edge of Roof 2. Photo 6 Set aside built right roof structure Photo 7 Photo 8 Build Left Room Structure 10. Connect left edge of Front Wall to right edge of Left Wall. Photo Connect left edge of Left Wall to right edge of Back Door Wall. Photo 8 Attach Left Room Structure to Right Room Structure 12. Connect the right edge of Front Wall into the 3 holes going down the right side interior of the Inner Wall. Photo Connect the left edge of the Back Door Wall into the 3 holes going down the left side interior of the Inner Wall. Photo 10 Photo 9 Photo 10 Close Up Back Side of Right Room Structure 14. Connect right edge of Right Wall to left edge of Back Wall. Photo 11 Attach Right Roof Structure to Right Room Structure 15. Connect top buttonette on left side of Front Door Wall into eyelet at top right interior of Roof Connect top buttonette on right side of Back Wall into eyelet at top left interior of Roof Connect top edge of Inner Wall into eyelets at the bottom of Roof 2. Photo Connect remaining buttonette on left side of Front Door Wall into eyelet on Roof Connect remaining buttonette on right side of Back Wall into eyelet on Roof 2.

8 Attach Left Roof Structure to Left Room Structure 20. Connect buttonette on top right of Front Wall into bottom right eyelet on Roof 3. Photo Connect buttonette on top left of Back Door Wall into bottom left eyelet on Roof 4. Photo Connect buttonettes on top right of Left Wall into eyelets on Roof 3. Photo Connect buttonettes on top left of Left Wall into eyelets on Roof 4. Photo Connect buttonette on top left of Front Wall into eyelet on Roof Connect buttonette on top right of Back Door Wall into eyelet on Roof 4. Attach Left Roof Structure to Right Roof Structure 26. Connect buttonette on right edge of Roof 3 into eyelet on Roof 2. Photo Connect buttonette on left edge or Roof 4 into eyelet on Roof 2. Photo 12 Photo 13 Photo 14 Photo 15 Attach Roof 1 to Right Roof Structure 28. Connect buttonette on top right of Front Door Wall into top left eyelet of Roof Connect buttonette on top left of Back Wall into top right eyelet of Roof Connect buttonettes on top edge of Right Wall into eyelets on the bottom of Roof Connect remaining buttonette on right edge of Front Door Wall into eyelet on Roof Connect remaining buttonette on left edge of Back Wall into eyelet on Roof 1. Photo 16 Inserting Foundations 33. side facing up connect buttonettes on Foundation 1 into eyelets of the right room structure except for the connection to the Inner Wall. Photo side facing up and tea light hole towards the center of the house connect buttonettes of Foundation 2 into eyelets of the left room structure except for the connection to the Inner Wall. Photo Connect remaining buttonette on Foundation 1 into the eyelet that is aligned on the Inner Wall. 36. Connect remaining buttonette on Foundation 2 into the eyelet that is aligned on the Inner Wall. Photo 17 Photo 18