Contents. Replacing Gateway Convertible Notebook Components... 1
|
|
- Derick Morton
- 7 years ago
- Views:
Transcription
1
2
3 Contents Replacing Gateway Convertible Notebook Components Identifying the convertible notebook model Identifying components Preparing your work space Preventing static electricity discharge Preparing the convertible notebook Removing the main battery Removing the optional secondary battery Replacing the modular drive Adding or replacing memory modules Replacing the cooling assembly Replacing the processor Replacing the IEEE Mini PCI card Replacing the CMOS battery Replacing the hard drive kit Replacing the hard drive in the hard drive kit Replacing the hinge covers Replacing the keyboard cover Replacing the keyboard Replacing the LCD panel assembly Replacing the LCD panel inverter Replacing the LCD panel lid Replacing the palm rest assembly Replacing the modem and system board i
4 ii
5 Replacing Gateway Convertible Notebook Components Important This service guide is not intended to be provided to individual users or consumers. It cannot be provided to anyone other than an authorized service provider. Use this service guide to help plan maintenance tasks for the Gateway CX200 convertible notebook. All tasks covered in this guide can be performed by an authorized field technician without jeopardizing the notebook s warranty. Important For information on the convertible notebook s general maintenance, technical support, safety notices, and regulatory notices, see the Gateway user guide. Important If you have suggestions regarding the content of this guide, send an with the subject Service Guide Comments to channel.services@gateway.com. 1
6 Replacing Gateway Convertible Notebook Components Identifying the convertible notebook model The label on the bottom of the convertible notebook contains information that identifies the convertible notebook model and its features. Caution It is important that you use the correct service guide for the convertible notebook. Failure to follow the approved tasks for the convertible notebook model may result in damage to the convertible notebook. 2
7 Identifying components Identifying components Where screw measurements are shown, the first number indicates screw head width, and the second number indicates screw length. Use this chart to identify the main components of the convertible notebook. For a complete list of replaceable parts, see Contents on page i. LCD panel assembly (see page 44) Keyboard cover (see page 38) Keyboard (see page 40) Cooling assembly (see page 16) Processor (see page 20) Palm rest assembly (see page 60) System board (see page 65) 3
8 Replacing Gateway Convertible Notebook Components Preparing your work space Before performing maintenance on the convertible notebook, make sure that your work space and the convertible notebook are correctly prepared. Wear a grounding (ESD) wrist strap, and use a grounded or dissipative work mat. Use a stable and strong table, and make sure that the table top is large enough to hold each component as you remove it. Use bright lighting to make part identification easier. Keep your work surface free from clutter and dust that may damage components. Use a magnetized screwdriver for removing screws. When removing components that are attached to the convertible notebook by a cable, unplug the cable before removing the screws, when possible, to avoid damaging the cable. As you remove components and screws, lay them toward the rear of your work surface (behind the convertible notebook) or far enough to the side that your arms do not accidentally brush them onto the floor. To help keep track of screws, try the following: Place each component s screws in their own section of a parts sorter. Place each component s screws next to the component on your work surface. Print the first page of each task, then place the page toward the rear of your work surface. As you remove screws, place the screws in their respective boxes on the page. Where screw measurements are shown, the first number indicates screw head width, and the second number indicates screw length. After loosening screws that are deeply recessed in a hole (for example, on the bottom of the base assembly), you can leave the screws in the holes if you place small pieces of masking tape over the hole openings. When reassembling the component, just remove the tape and tighten the screws. When you place flat-headed screws on your work surface, stand them on their heads to prevent the screws from rolling off the table. 4
9 Preventing static electricity discharge Preventing static electricity discharge Important Before performing maintenance on the convertible notebook, you should read and understand the information in this section. The components inside your convertible notebook are extremely sensitive to static electricity, also known as electrostatic discharge (ESD). Warning To avoid exposure to dangerous electrical voltages and moving parts, turn off your convertible notebook and unplug the power cord, modem cable, and network cable before opening the case. Warning To prevent risk of electric shock, do not insert any object into the vent holes of the convertible notebook. Before performing maintenance on the convertible notebook, follow these guidelines: Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam. Remove components from their antistatic bags only when you are ready to use them. Do not lay components on the outside of antistatic bags because only the inside of the bags provide electrostatic protection. Always hold components by their edges. Avoid touching the edge connectors. Never slide components over any surface. Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare metal part of your workbench or other grounded connection. Touch a bare metal surface on your workbench or other grounded object. 5
10 Replacing Gateway Convertible Notebook Components Preparing the convertible notebook Warning To avoid exposure to dangerous electrical voltages and moving parts, turn off the convertible notebook, remove the battery, and unplug the power cord, modem cable, and network cable before opening the case. Replace the cover before you restore power or reconnect the modem and network cables. To prepare the convertible notebook for maintenance: 1 Make sure that the CD or DVD drive is empty. 2 Turn off the convertible notebook and unplug the power cord, modem cable, and network cable. 3 Make sure the LCD panel is in notebook mode, then close the LCD panel. 4 Disconnect all peripheral devices and remove any PC Cards. 5 Unplug from the optional port replicator from the notebook. 6 Remove the main and optional secondary battery. For more information, see Removing the main battery on page 7 and Removing the optional secondary battery on page
11 Preparing the convertible notebook Removing the main battery To remove the main battery: 1 Turn the convertible notebook over so the bottom is facing up. 2 Slide the battery lock to the unlocked position, then slide the battery release latch. 3 Slide the battery out of the bay. 7
12 Replacing Gateway Convertible Notebook Components Removing the optional secondary battery To remove the optional secondary battery: 1 Turn the convertible notebook over so the bottom is facing up. 2 Remove the modular bay lock screw (if one is present), then slide and hold the module bay latch. The battery may move out slightly. Modular bay lock screw 8
13 Preparing the convertible notebook 3 Slide the battery out. 9
14 Replacing Gateway Convertible Notebook Components Replacing the modular drive Important Install only a Gateway CX200 modular drive in the modular bay. Tools you need to complete this task: Phillips #0 screwdriver To replace the modular drive: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Turn the convertible notebook over so the bottom is facing up. 3 Remove the modular bay lock screw (if one is present), then slide and hold the module bay latch. The drive may move out slightly. Modular bay lock screw 10
15 Replacing the modular drive 4 Slide the drive out. 5 Firmly push the new drive straight into the bay until the latch clicks into place. 6 Replace the module bay lock screw. 11
16 Replacing Gateway Convertible Notebook Components Adding or replacing memory modules Important Use only memory modules designed for the Gateway CX200. Tools you need to complete this task: Phillips #0 screwdriver Memory bay 12
17 Adding or replacing memory modules To add or replace memory modules: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Loosen the six memory bay cover screws that secure the memory cover. (These screws cannot be removed.) 3 Remove the memory bay cover. Tips & Tricks Be careful not to break off the tabs located on the bottom of the cover. Slide the cover in the direction shown. If the cover does not slide easily, wiggle the cover to loosen it. 13
18 Replacing Gateway Convertible Notebook Components 4 If you are removing a module, gently press outward on the clip at each end of the memory module until the module tilts upward. Clip Clip 5 Pull the memory module out of the slot. 14
19 Adding or replacing memory modules 6 Hold the new or replacement module at a 30-degree angle and press it into the empty memory slot. This module is keyed so it can only be inserted in one direction. If the module does not fit, make sure that the notch in the module lines up with the tab in the memory bay. Important Use only memory modules designed for the Gateway CX Gently push the module down until it clicks in place. 8 Replace the memory bay cover, then tighten the cover screws. 15
20 Replacing Gateway Convertible Notebook Components Replacing the cooling assembly Tools you need to complete this task: Phillips #0 screwdriver s removed during this task: 6 chrome (cooling assembly) 16
21 Replacing the cooling assembly To replace the cooling assembly: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Loosen the six memory bay cover screws that secure the memory cover. (These screws cannot be removed.) 3 Remove the memory bay cover. Tips & Tricks Be careful not to break off the tabs located on the bottom of the cover. Slide the cover in the direction shown. If the cover does not slide easily, wiggle the cover to loosen it. 17
22 Replacing Gateway Convertible Notebook Components 4 Remove the four screws that are stamped with the numbers 1 through 4 next to them. Make sure that you remove the screws in reverse numerical order. Caution When removing the cooling assembly s screws from the numbered holes, remove them in reverse numerical order. Caution There are thermal pads beneath the cooling assembly. Do not remove the thermal pads. 5 Remove the two remaining screws that connect the cooling assembly to the system board. 18
23 Replacing the cooling assembly 6 Unplug the old cooling fan. 7 Lift the cooling assembly up and away from the convertible notebook. 8 Install the new cooling assembly in the convertible notebook. 9 Plug in the new cooling fan. 10 Replace the four screws that are stamped with the numbers 1 through 4 next to them. Make sure that you tighten the screws in numerical order. Caution When tightening the cooling assembly s screws into the numbered holes, tighten them in numerical order. 11 Replace the other two screws that connect the cooling assembly to the system board. 12 Replace the memory bay cover, then tighten the cover screws. 19
24 Replacing Gateway Convertible Notebook Components Replacing the processor Tools you need to complete this task: Flat-blade driver Phillips #0 screwdriver s removed during this task: 6 chrome (cooling assembly) 20
25 To replace the processor: 1 Complete the steps in Preparing the convertible notebook on page 6. Replacing the processor 2 Loosen the six memory bay cover screws that secure the memory cover. (These screws cannot be removed.) 3 Remove the memory bay cover. Tips & Tricks Be careful not to break off the tabs located on the bottom of the cover. Slide the cover in the direction shown. If the cover does not slide easily, wiggle the cover to loosen it. 4 Remove the cooling assembly by following the instructions in Replacing the cooling assembly on page
26 Replacing Gateway Convertible Notebook Components 5 Use a flat-blade screwdriver to turn the processor lock screw ¼-turn counter-clockwise. 22
27 Replacing the processor 6 Remove the old processor from the system board. 7 Install the new processor onto the system board making sure that Pin 1 on the processor (indicated by the silk-screened arrow on the corner of the processor) aligns with Pin 1 on the processor socket (indicated by the absence of a pin hole in the processor socket), then use a flat-blade screwdriver to turn the processor lock screw ¼-turn clockwise. 8 Reassemble the notebook. 23
28 Replacing Gateway Convertible Notebook Components Replacing the IEEE Mini PCI card Caution By law, only approved wireless modules provided by Gateway, or a Gateway authorized representative, explicitly for the Gateway CX200 may be installed in this convertible notebook. Caution Legal requirements dictate the mini PCI cover plate be in place during any and all operation of the convertible notebook s wireless feature. Tools you need to complete this task: Phillips #0 screwdriver mini PCI bay 24
29 Replacing the IEEE Mini PCI card To replace the IEEE Mini PCI card: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Loosen the screw that secures the mini PCI cover. (This screw cannot be removed.) 3 Remove the mini PCI cover. 25
30 Replacing Gateway Convertible Notebook Components 4 Unplug the two antenna cables from the mini PCI card. 26
31 Replacing the IEEE Mini PCI card 5 Move the antenna cables out of the way, then press outward on the clips at both sides of the card until the card tilts upward. 0 Clip Clip 27
32 Replacing Gateway Convertible Notebook Components 6 Pull the card out of the slot. 7 Hold the new card at a 30-degree angle and press it into the empty slot. This card is keyed so it can only be inserted in one direction. If the card does not fit, make sure that the notch in the card lines up with the tab in the card slot. 8 Move the antenna cables out of the way, then press the card down until it clicks into place. 28
33 Replacing the IEEE Mini PCI card 9 Reattach the black antenna cable to the connector labelled MAIN or M, then reattach the light gray antenna cable to the connector labelled AUX or A. 10 Replace the mini PCI cover, then tighten the cover screw. 29
34 Replacing Gateway Convertible Notebook Components Replacing the CMOS battery Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver To replace the CMOS battery: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Open the mini PCI compartment by following the instructions in Replacing the IEEE Mini PCI card on page 24. If your convertible notebook has a mini PCI card, remove it. 3 Locate the old battery on the system board. 4 Insert the small flat-blade screwdriver or non-marring tool under the old battery and gently pry it up until it pops out of the socket. 5 Make sure the positive (+) side of the new battery is facing up, then press the battery into the socket until it snaps into place. 6 Reassemble the convertible notebook. 30
35 Replacing the hard drive kit Replacing the hard drive kit Tools you need to complete this task: Phillips #0 screwdriver Hard drive To replace the hard drive kit: 1 Create a Drivers and Applications Recovery disc using the procedure found in the Using Gateway System Recovery online guide. To access this guide, tap or click Start, All Programs, System Recovery, then tap or click Recovery Help Manual. 2 Print the Using Gateway System Recovery online guide for use in Step Back up any data you want to transfer to the new hard drive. For more information, see Backing up files in Using Your Computer which has been included on your hard drive. To access this guide, tap or click Start, All Programs, then tap or click Gateway Documentation. 4 Complete the steps in Preparing the convertible notebook on page
36 Replacing Gateway Convertible Notebook Components 5 Loosen the two hard drive bay cover screws (they cannot be removed), then remove the hard drive bay cover. 32
37 Replacing the hard drive kit 6 Remove the hard drive screw. 33
38 Replacing Gateway Convertible Notebook Components 7 Slide the old hard drive kit out of the convertible notebook. Important If your new hard drive does not include the hard drive kit bracket, complete the steps in Replacing the hard drive in the hard drive kit on page 35 before proceeding. 8 Slide the new hard drive kit into the convertible notebook. 9 Replace the screw that secures the hard drive kit to the convertible notebook. 10 Replace the hard drive bay cover. 11 For instructions on installing Windows, your drivers, and your applications, see the Using Gateway System Recovery online guide you printed in Step
39 Replacing the hard drive in the hard drive kit Replacing the hard drive in the hard drive kit Tools you need to complete this task: Phillips #0 screwdriver s removed during this task: 4 chrome (hard drive) To replace the hard drive in the hard drive kit: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Remove the hard drive kit by following the instructions in Replacing the hard drive kit on page
40 Replacing Gateway Convertible Notebook Components 3 Remove the four screws that secure the hard drive to the hard drive kit bracket. 4 Remove the bracket from the old drive. 5 Insert the new drive into the bracket, label side up, so the screw holes line up. 6 Replace the four screws that secure the bracket to the drive. 7 Slide the hard drive kit into the convertible notebook. 8 Replace the screw that secures the hard drive kit to the convertible notebook. 9 Replace the hard drive bay cover. 36
41 Replacing the hinge covers Replacing the hinge covers Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool To replace the hinge covers: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Turn the convertible notebook over so the top is facing up. 3 Insert the small flat-blade screwdriver or non-marring tool under the bottom of the back hinge cover, then carefully pry it up. 4 Open the LCD panel to the fully open position, insert the small flat-blade screwdriver or non-marring tool under the bottom of the front hinge cover, then carefully pry it up. 5 Snap the new front cover into place over the hinge, then snap the back cover into place. 37
42 Replacing Gateway Convertible Notebook Components Replacing the keyboard cover Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool To replace the keyboard cover: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Turn the convertible notebook over so the top is facing up. 3 Open the LCD panel to the normal viewing position. 4 Insert the small flat-blade screwdriver under the bottom of the keyboard cover between the PAUSE and INSERT keys and gently pry it up. Tips & Tricks Inserting a piece of cloth between the screwdriver and keyboard will help prevent damage to the convertible notebook. 5 Insert the small flat-blade screwdriver under the bottom of the keyboard cover between the F1 and F2 keys and gently pry it up. 38
43 Replacing the keyboard cover 6 Remove the keyboard cover from the convertible notebook by pulling the cover toward you and at the same time lifting its front to clear the keyboard. You will hear small snapping sounds as the cover comes away from the convertible notebook. Be careful not to break off the tabs located on the bottom of the cover. 7 Slide the tabs on the bottom side of the new cover under the convertible notebook frame. 8 Press down on the cover in several places to make sure that it is correctly mounted. The cover is correctly mounted when you can run your finger along the cover and find no loose spots. The cover should be flat all the way across. Caution If the cover is not correctly replaced, the convertible notebook could be damaged when you try to close the LCD panel. 39
44 Replacing Gateway Convertible Notebook Components Replacing the keyboard Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver s removed during this task: 2 black (keyboard) 40
45 To replace the keyboard: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Remove the two keyboard screws marked with a K. Replacing the keyboard 3 Turn the convertible notebook over so the top is facing up. 4 Remove the keyboard cover by following the instructions in Replacing the keyboard cover on page
46 Replacing Gateway Convertible Notebook Components 5 Lift the back edge of the keyboard slightly, then carefully push it toward the LCD panel to release the keyboard retaining tabs. Be careful not to damage the LCD panel. 6 Carefully rotate the keyboard toward you so it lies keys-down on top of your notebook. Be careful not to damage the LCD panel. 7 Lift the black keyboard connector clip, then remove the cable. Be careful not to touch or damage any other components. Keyboard connector clip 42
47 Replacing the keyboard 8 Lift the old keyboard away from the notebook. The keyboard is now completely detached from the notebook. 9 Place the new keyboard keys-down on your notebook with the space bar away from you. 10 Make sure the black keyboard connector clip is fully raised, insert the cable into the connector, then lower the black connector clip to lock the connector in place. Important The cable is correctly oriented if the cable is not twisted. 11 Rotate the keyboard toward the LCD panel until the keyboard is almost face-up. 12 Insert the tabs on the front edge of the keyboard into the slot under the palm rest. It may be necessary to press down on the keyboard keys along the front edge of the keyboard to seat the retaining tabs into their corresponding slots. 13 Gently press the keyboard down until it is flat all the way across. The keyboard should easily fall into place. Be careful not to damage the LCD panel. 14 Reattach the keyboard cover by following the instructions in Replacing the keyboard cover on page Turn the notebook over so the bottom is facing up, then replace the keyboard screws. Tips & Tricks The screw holes are marked with a K. 43
48 Replacing Gateway Convertible Notebook Components Replacing the LCD panel assembly Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver s removed during this task: 6 black (LCD panel assembly hinge) To replace the LCD panel assembly: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 If the convertible notebook has IEEE wireless networking built in, unplug the antenna cables from the IEEE mini PCI card by following the instructions in Replacing the IEEE Mini PCI card on page
49 Replacing the LCD panel assembly 3 Remove the four screws on the bottom that secure the LCD panel hinge to the chassis. 4 Turn the convertible notebook over so the top is facing up. 5 Remove the hinge covers by following the instructions in Replacing the hinge covers on page Open the LCD panel to the fully open position. Caution Be careful not to use too much force when opening the LCD panel. 7 Remove the keyboard cover by following the instructions in Replacing the keyboard cover on page
50 Replacing Gateway Convertible Notebook Components 8 Remove the two screws on the top that secure the LCD panel hinge to the chassis. 9 Detach the three cables from the system board. 10 Grasp the plastic tab carefully and pull to unplug the LCD video cable from the convertible notebook. Make sure you grasp the tab, not the cable. Caution The connector is fragile. 46
51 Replacing the LCD panel assembly 11 Taking care to note the cables routing and positions as they are installed from Gateway, pull the antenna cables out from under the system board, then slide the wires out from under the retaining clips. 12 Lift the LCD panel assembly up and away from the convertible notebook. The LCD panel assembly is now completely detached from the convertible notebook. 13 Place the new LCD panel assembly onto the hinge of the convertible notebook, then replace the two hinge screws. 14 Slide the antenna cables through the retaining clips, under the system board, then into the mini-pci card area. 15 Plug the LCD video cable into the convertible notebook. 16 Reattach the three cables to the appropriate connectors on the system board. 17 Reassemble the convertible notebook. 18 Turn the notebook over so the bottom is facing up, then replace the four screws on the bottom that secure the hinge to the chassis. 19 If the notebook has IEEE wireless networking built in, plug the black antenna cable into the IEEE mini PCI card connector labelled MAIN or M, then plug the light gray antenna cable to the connector labelled AUX or A. 47
52 Replacing Gateway Convertible Notebook Components Replacing the LCD panel inverter Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver s removed during this task: 6 black (hinge) 8 black (LCD panel assembly) 4 black (LCD panel) 1 chrome (inverter) To replace the LCD panel inverter: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 If the convertible notebook has IEEE wireless networking built in, unplug the antenna cables from the IEEE mini PCI card by following the instructions in Replacing the IEEE Mini PCI card on page
53 Replacing the LCD panel inverter 3 Remove the four screws on the bottom that secure the LCD panel hinge to the chassis. 4 Turn the convertible notebook over so the top is facing up. 5 Remove the hinge covers by following the instructions in Replacing the hinge covers on page Open the LCD panel to the fully open position. Caution Be careful not to use too much force when opening the LCD panel. 7 Remove the keyboard cover by following the instructions in Replacing the keyboard cover on page Remove the LCD panel by following the instructions in Replacing the LCD panel assembly on page
54 Replacing Gateway Convertible Notebook Components 9 Remove the eight rubber inserts from the front of the LCD panel assembly. Insert Insert Insert Insert Insert Insert Insert Insert 10 Remove the eight screws from the front of the LCD panel assembly. 50
55 Replacing the LCD panel inverter 11 Carefully separate the front and back of the LCD panel assembly. 12 Disconnect the connector from the inverter. 13 Remove the screw that connects the inverter to the front of the LCD panel assembly. 14 Replace the inverter. 15 Replace the screw that was removed in Step 13, then reconnect the cable. 51
56 Replacing Gateway Convertible Notebook Components 16 Press the LCD panel front and back together. Press the two halves together in several places until they click in place. You should find no loose spots or spots where the two halves do not meet. 17 Replace the eight LCD panel assembly screws. 18 Replace the eight inserts. Caution The four larger rubber inserts go across the top of the panel. 19 Reassemble the convertible notebook. 52
57 Replacing the LCD panel lid Replacing the LCD panel lid Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver s removed during this task: 6 black (hinge) 8 black (LCD panel assembly) 2 chrome (tablet button board) 2 chrome (power button board) 1 chrome (inverter) 4 black (LCD panel) 4 chrome (hinge) 53
58 Replacing Gateway Convertible Notebook Components To replace the LCD panel lid: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 If the convertible notebook has IEEE wireless networking built in, unplug the antenna cables from the IEEE mini PCI card by following the instructions in Replacing the IEEE Mini PCI card on page Remove the four screws on the bottom that secure the LCD panel hinge to the chassis. 4 Turn the convertible notebook over so the top is facing up. 5 Remove the hinge covers by following the instructions in Replacing the hinge covers on page Open the LCD panel to the fully open position. Caution Be careful not to use too much force when opening the LCD panel. 7 Remove the keyboard cover by following the instructions in Replacing the keyboard cover on page Remove the LCD panel by following the instructions in Replacing the LCD panel assembly on page
59 Replacing the LCD panel lid 9 Remove the eight rubber inserts from the front of the LCD panel assembly. Insert Insert Insert Insert Insert Insert Insert Insert 10 Remove the eight screws from the front of the LCD panel assembly. 55
60 Replacing Gateway Convertible Notebook Components 11 Carefully separate the front and back of the LCD panel assembly. 12 Disconnect the tablet button cable from the tablet button board. Connector 13 Remove the two screws that connect the tablet button board to the front of the LCD panel assembly. 56
61 14 Disconnect the power button cable from the power button board. Replacing the LCD panel lid Connector 15 Remove the two screws that connect the power button board to the front of the LCD panel assembly. 16 Disconnect the connector from the inverter. 17 Remove the screw that connects the inverter to the front of the LCD panel assembly. 57
62 Replacing Gateway Convertible Notebook Components 18 Remove the four screws that secure the LCD panel to the LCD panel assembly. 19 Remove the four screws that secure the hinge to the LCD panel assembly and move it to the new LCD panel lid. s s 20 Place the LCD panel into the new LCD panel lid and replace the four screws. 21 Place the inverter, power button board, and tablet button board into the new LCD panel lid, replace the screws, and connect the boards. 58
63 Replacing the LCD panel lid 22 Press the LCD panel front and back together. Press the two halves together in several places until they click in place. You should find no loose spots or spots where the two halves do not meet. 23 Replace the eight LCD panel assembly screws. 24 Replace the eight inserts. Caution The four larger rubber inserts go across the top of the panel. 25 Reassemble the convertible notebook. 59
64 Replacing Gateway Convertible Notebook Components Replacing the palm rest assembly Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver s removed during this task: 1 chrome (modular drive) 2 black (keyboard) 6 black (LCD panel assembly hinge) 16 black (palm rest-bottom) 2 chrome (palm rest) 3 chrome (palm rest) 1 chrome (palm rest-top) 60
65 Replacing the palm rest assembly To replace the palm rest assembly: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Remove the modular drive by following the instructions in Replacing the modular drive on page Remove the memory bay cover by following the instructions in Adding or replacing memory modules on page If the convertible notebook has IEEE wireless networking built in, unplug the antenna cables from the IEEE mini PCI card by following the instructions in Replacing the IEEE Mini PCI card on page Remove the hard drive by following the instructions in Replacing the hard drive kit on page Remove the hinge cover by following the instructions in Replacing the hinge covers on page Remove the keyboard cover by following the instructions in Replacing the keyboard cover on page Remove the keyboard by following the instructions in Replacing the keyboard on page Remove the LCD panel by following the instructions in Replacing the LCD panel assembly on page
66 Replacing Gateway Convertible Notebook Components 10 Remove the 16 black screws and 5 chrome screws on the bottom of the convertible notebook. s s s s 62
67 Replacing the palm rest assembly 11 Remove the screw on the top of the convertible notebook. 12 Gently lift the hinge off the touchpad cable. The cable is now free. Touchpad connector 13 Lift the palm rest assembly up and away from the convertible notebook. 14 Place the new palm rest assembly onto the convertible notebook. 15 Replace the top palm rest screw. 63
68 Replacing Gateway Convertible Notebook Components 16 Make sure that the black plastic hinge on the system board touchpad connector is in the raised position. 17 Insert the end of the touchpad cable between the black plastic hinge and the white connector. 18 Press the black plastic hinge onto the touchpad cable. 19 Replace the chrome screw you removed in Step Turn the convertible notebook so the bottom is facing up. 21 Replace the 16 black screws and 5 chrome screws on the bottom of the convertible notebook. Important The two small chrome screws fit into the hard drive bay. The three chrome screws with the large heads fit in the modular bay. 22 Reassemble the convertible notebook. 64
69 Replacing the modem and system board Replacing the modem and system board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver s removed during this task: 1 chrome (modular drive) 2 black (keyboard) 6 black (LCD panel assembly hinge) 16 black (palm rest-bottom) 2 chrome (palm rest) 3 chrome (palm rest) 1 chrome (palm rest-top) 4 black (system board) 2 chrome (modem) 65
70 Replacing Gateway Convertible Notebook Components To replace the modem and system board: 1 Complete the steps in Preparing the convertible notebook on page 6. 2 Remove the modular drive by following the instructions in Replacing the modular drive on page Remove the memory modules by following the instructions in Adding or replacing memory modules on page Remove the cooling assembly by following the instructions in Replacing the cooling assembly on page Remove the processor and install it on the new system board by following the instructions in Replacing the processor on page Remove the mini PC card from the convertible notebook by following the instructions in Replacing the IEEE Mini PCI card on page Remove the hard drive kit by following the instructions in Replacing the hard drive kit on page Remove the hinge cover by following the instructions in Replacing the hinge covers on page Remove the keyboard cover by following the instructions in Replacing the keyboard cover on page Remove the keyboard by following the instructions in Replacing the keyboard on page Remove the LCD panel by following the instructions in Replacing the LCD panel assembly on page Remove the palm rest assembly by following the instructions in Replacing the palm rest assembly on page
71 13 Unplug the speakers from the system board (one connector). Replacing the modem and system board Speaker connector 14 Remove the four system board screws. 67
72 Replacing Gateway Convertible Notebook Components 15 Carefully remove the system board. Caution The modem cable is attached to the bottom of the notebook. 16 Turn the system board over so the bottom is facing up, then remove the screws that secure the modem to the convertible notebook. 17 Insert the small flat-blade screwdriver or non-marring tool under the modem and gently pry it up about ¼ inch. 68
73 Replacing the modem and system board 18 Turn the modem over, then unplug the modem cable from the modem. 19 Install the modem on the new system board. 20 Place the new system board into the convertible notebook. 21 Replace the four system board screws in the holes on the top of the system board. 22 Reassemble the convertible notebook. 69
74 Replacing Gateway Convertible Notebook Components 2005 Gateway, Inc. All rights reserved. Gateway, Gateway Country, the Gateway stylized logo, and the black-and-white spot design are trademarks or registered trademarks of Gateway, Inc. in the United States and other countries. All other brands and product names are trademarks or registered trademarks of their respective companies. 70
75
76 MAN VIPER SVC GDE R0 8/05
Service Guide. Gateway M275
Service Guide Gateway M275 Contents Replacing Gateway M275 Components.................................... 1 Identifying the convertible tablet PC model...................................... 2 Identifying
More informationSERVICE GUIDE. Gateway Notebook
SERVICE GUIDE Gateway Notebook Contents Replacing Gateway Notebook Components...................................1 Identifying the notebook model......................................... 2 Identifying
More informationReplacing the Gateway M320 Keyboard
Replacing the Gateway M320 Keyboard This package includes a replacement keyboard for your Gateway M320 notebook and these printed instructions. Tools you need You need a small Phillips and a small flat-blade
More informationReplacing the Gateway M675 Keyboard
Replacing the Gateway M675 Keyboard This package includes a replacement keyboard for your Gateway M675 notebook and these printed instructions. Tools you need You need a small Phillips screwdriver and
More informationEasyNote TJ Series. Disassembly Manual
EasyNote TJ Series Disassembly Manual CHAPTER3 Replacing notebook components Preventing static electricity discharge Preparing the work space Required tools Preparing the notebook Adding or replacing memory
More informationUPGRADING AND SERVICING GUIDE
UPGRADING AND SERVICING GUIDE HPTouchSmart 610 PC Computer features may vary by model. Removing and Replacing a CD/DVD Drive...2 Removing the CD/DVD Drive... 2 Installing a New CD/DVD Drive... 5 Removing
More informationReplacement Instructions. Warning: During this procedure, keep small parts away from children.
apple ibook G4 Memory Card Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Written
More informationCompaq Presario Desktop Products. Upgrading and Servicing Guide
Compaq Presario Desktop Products Upgrading and Servicing Guide The information in this document is subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to
More informationUpgrading and Servicing Guide
Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed
More informationInspiron 15. Service Manual. 3000 Series
Inspiron 15 3000 Series Service Manual Computer Model: Inspiron 15 3541/Inspiron 15 3542/Inspiron 15 3543 Regulatory Model: P40F Regulatory Type: P40F001/P40F002 Notes, Cautions, and Warnings NOTE: A NOTE
More informationapple Service Source PowerBook G4 (DVI) Updated 4 December 2003 2003 Apple Computer, Inc. All rights reserved.
apple Service Source PowerBook G4 (DVI) Updated 4 December 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Upgrades PowerBook G4 (DVI) 2003 Apple Computer, Inc. All rights reserved.
More informationHP Pavilion All-in-One MS200 series PC. Upgrading and Servicing Guide. Printed in
HP Pavilion All-in-One MS200 series PC *579907-001* *579907-001* Printed in Upgrading and Servicing Guide Replacing a Wireless Keyboard or Mouse...2 Before You Begin... 2 Replacing the Keyboard or Mouse...
More informationSmall form factor bay converter and hard drive installation
Small form factor bay converter and hard drive installation HP xw6600 and HP xw8600 Workstations This document describes how to convert HP xw6600 and HP xw8600 Workstation 3.5-inch hard drive bays to hold
More informationFront Panel Board Cable Replacement Instructions
apple Mac Pro Front Panel Board Cable Replacement Instructions First Steps 1 Shut down computer. Note: Follow these instructions carefully. Failure to do so could damage your equipment and void its warranty.
More informationInspiron 13. Service Manual. 7000 Series. Computer Model: Inspiron 13 7348 Regulatory Model: P57G Regulatory Type: P57G001
Inspiron 13 7000 Series Service Manual Computer Model: Inspiron 13 7348 Regulatory Model: P57G Regulatory Type: P57G001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps
More informationAcer Aspire One AOA150-1570 Disassembly
Acer Aspire One AOA150-1570 Disassembly Model The Acer Aspire One AOA150-1570 is the model with the 120GB hard drive (not the Flash drive) and 1GB RAM with Windows XP. Disassembly Beware of the ESD (ElectroStatic
More informationMemory Modules. Document Part Number: 407947-001. This guide explains how to replace and upgrade memory in the computer. May 2006
Memory Modules Document Part Number: 407947-001 May 2006 This guide explains how to replace and upgrade memory in the computer. Contents 1 Adding or replacing memory modules Adding or replacing a memory
More informationExpress5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001
Express5800/120Ed Rack Mount Kit Installation Procedures PN: 455-01607-001 Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials,
More informationInstalling the Video Input and TV Tuner Cards in a Compact Computer or a Dual PCI-Slot Tower Computer
Installing the Video Input and TV Tuner Cards in a Compact Computer or a Dual PCI-Slot Tower Computer This booklet describes how to install the video input and TV tuner cards in a compact Macintosh computer
More informationPackard Bell. EasyNote MZ series. Disassembly Manual
Packard Bell EasyNote MZ series Disassembly Manual Table of Contents Overview...3 Technician Notes...3 Disassembly Instructions...3 Reassembly Instructions...3 Required Tools...3 Battery...4 Memory...4
More informationMemory Modules. Document Part Number: 396849-001. This guide explains how to replace and upgrade memory in the computer.
Memory Modules Document Part Number: 396849-001 March 2006 This guide explains how to replace and upgrade memory in the computer. Contents 1 Adding or replacing memory modules Adding a memory module to
More informationWall-Mounting your HP computer. User Guide
Wall-Mounting your HP computer User Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should
More informationMemory Modules User Guide
Memory Modules User Guide Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services
More informationReplacement Instructions. Warning: During this procedure, keep small parts away from children.
apple Power Mac G4 / Macintosh Server G4 ATA Hard Drive Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void
More informationHP SATA/SAS hard drive and Solid State Drive installation
HP SATA/SAS hard drive and Solid State Drive installation This document describes how to install Serial ATA (SATA) and Serial Attached SCSI (SAS) hard drives or Solid State Drives (SSD) in an internal
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationDisassembly Procedure
Chapter 2 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before. A SUS
More informationHP ProLiant DL165 G7 Server. Installation Instructions
HP ProLiant DL165 G7 Server Installation Instructions Identifying server components Front panel components Figure 1 Front Panel Components / 4 3.5 HDD Item 1 Thumbscrews for rack mounting 2 Drive status
More informationProcessor Cage Fans, Front and Rear Replacement Instructions
apple Mac Pro Processor Cage Fans, Front and Rear Replacement Instructions First Steps 1 Shut down computer. Note: Follow these instructions carefully. Failure to do so could damage your equipment and
More informationDisassembly Procedure
Chapter 2 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the Eee PC 4G (701). Be sure to use proper tools described before.
More informationWritten By: Sam Lionheart
iphone 5s Battery Replacement Replace the battery in your iphone 5s. Written By: Sam Lionheart INTRODUCTION Use this guide to bring life back to your iphone 5s with a new battery. Removing the battery
More informationIntel NUC Kit DC3217IYE User Guide. Intel NUC Kit DC3217IYE
Intel NUC Kit DC3217IYE User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers and with the safety practices
More informationDell Latitude C610/C510 Service Manual
Dell Latitude C610/C510 Service Manual Dell Latitude C610/C510 Service Manual Before You Begin System Components Hard Drive Memory Modules, Mini PCI Card, and Modem Keyboard Display Assembly, Display Latch,
More informationDell Inspiron 660s Owner s Manual
Dell Inspiron 660s Owner s Manual Computer model: Inspiron 660s Regulatory model: D06S Regulatory type: D06S001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you
More informationapple Service Source Power Mac G4 Cube Updated June 2, 2003 2002 Apple Computer, Inc. All rights reserved.
apple Service Source Power Mac G4 Cube Updated June 2, 2003 2002 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Power Mac G4 Cube 2002 Apple Computer, Inc. All rights reserved.
More informationPackard Bell Easy Repair
Your digital playground Packard Bell Easy Repair EasyNote MX Series Hard Disk Drive Repair Instructions www.packardbell.com Your digital playground Important Safety Check Instructions You must read all
More information430 Power/Electronics Replacement
Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed
More informationDell Latitude X300 Service Manual
Dell Latitude X300 Service Manual Dell Latitude X300 Service Manual Before You Begin Dell Diagnostics System Components Battery Memory, Modem, and Mini PCI Card Modules Keyboard Palm Rest Hard Drive Hinge
More informationIntel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide
Intel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide Thank you for buying an Intel RAID Maintenance Free Backup Unit 4. The Intel RAID Maintenance Free Backup Unit 4 supports the Intel
More informationWritten By: Walter Galan
ipad 2 GSM LCD Replacement Replace the LCD in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Use this guide to replace a broken LCD. TOOLS: iopener (1) Phillips #00 Screwdriver (1) Plastic Opening
More informationInstallation Guide. Wyse D Class 4-GB RAM Upgrade Option Kit. Products: D90D7, D90DW. Issue: 121312 PN: 883884-35L Rev. A
Installation Guide Wyse D Class 4-GB RAM Upgrade Option Kit Products: D90D7, D90DW Issue: 121312 PN: 883884-35L Rev. A Copyright Notices 2012, Wyse Technology Inc. All rights reserved. This manual and
More informationWritten By: Walter Galan
ipad 2 GSM Rear Camera Replacement Replace the rear camera in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Use this guide to replace a broken rear camera. TOOLS: ifixit Opening Picks set of 6
More informationRemoving memory and option cards
These instructions can help you remove memory or option cards. Use the following illustration to locate the connector for the card you want to remove. Hard disk connector 1 Option card connector Firmware
More informationZ-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly
Replacing the Cover Micro-Switch To remove and replace the Cover Micro-Switch you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) #1 Phillips screwdriver (magnetic tip preferred)
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More informationKurzweil KORE 64. ROM Expansion Board for the PC3 and PC3K
Kurzweil KORE 64 ROM Expansion Board for the PC3 and PC3K Installation Instructions August 1, 2012 2012 Young Chang Co., Ltd. All rights reserved. Kurzweil is a product line of Young Chang Co., Ltd. Kurzweil,
More informationChanging the SIM in a BANDIT Product s GSM Card
encor! enetworks TM Version A.2, January 2013 2013 Encore Networks, Inc. All rights reserved. Changing the SIM in a BANDIT Product s GSM Card Wireless connections use radiofrequencies (RFs) through airwaves
More informationHP Laser Jet 4200/4240/4250/4300/4350 Swing Plate
HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate 1 Swing Plate Assembly-RM1-0043 1 Swing Plate Kit-5851-2766 (RM1-0043 plus RM1-1091 gear) CAUTION: Fuser may be hot. Turn off printer, unplug it and allow
More informationBuilding A Computer: A Beginners Guide
Building A Computer: A Beginners Guide Mr. Marty Brandl The following was written to help an individual setup a Pentium 133 system using an ASUS P/I- P55T2P4 motherboard. The tutorial includes the installation
More informationKEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
More informationHP 22-in-1 Media Card Reader
HP 22-in-1 Media Card Reader Introduction This document describes how to install the HP 22-in-1 Media Card Reader into an HP Workstations adapter bracket, and then install the media card reader and bracket
More informationWritten By: Walter Galan
ipad 2 GSM Front Panel Replacement Replace the front panel in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Note: this is a complete guide for replacing a plain front panel. If you have a Front
More informationWritten By: Walter Galan
Installing iphone 4S Display Assembly Written By: Walter Galan TOOLS: Phillips 00 Screwdriver (1) Plastic Opening Tools (1) PARTS: iphone 4S Display Assembly (1) iphone 4 and 4S Screen Protector (1) Small
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationInstallation Guide. Wyse C Class 2-GB RAM Upgrade Option Kit. Issue: 092910 PN: 883884-13L Rev. A
Installation Guide Wyse C Class 2-GB RAM Upgrade Option Kit Issue: 092910 PN: 883884-13L Rev. A Copyright Notices 2010, Wyse Technology Inc. All rights reserved. This manual and the software and firmware
More information5800 Temperature Sensor Cable Assembly
5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationHARDWARE REFERENCE. Gateway Notebook
HARDWARE REFERENCE Gateway Notebook Contents Chapter 1: About this reference...............................................1 About this guide........................................................ 2
More informationInstallation Guide. Wyse Z Class 2 and 4-GB RAM Upgrade Option Kit. Products: Z90DW, Z90SW, Z90D7, Z90S7. Issue: 122211 PN: 883884-32L Rev.
Installation Guide Wyse Z Class 2 and 4-GB RAM Upgrade Option Kit Products: Z90DW, Z90SW, Z90D7, Z90S7 Issue: 122211 PN: 883884-32L Rev. A Copyright Notices 2011, Wyse Technology Inc. All rights reserved.
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationGE Wireless Devices Battery Replacement
60-506-319.5 Crystal Smoke Detector Two 9V Duracell 9V 1. Twist counter-clockwise until detector become loose from base. 2. Replace batteries observing correct polarity. 3. Replace detector by twisting
More informationYour Simple Guide to Battery. www.firstalertpro.com. Replacement. Customer Care: 1-800-852-0086. www.firstalertpro.
Previous Menu Your Simple Guide to Battery www.firstalertpro.com Replacement p e t s ts ep -by Customer Care: 1-800-852-0086 FA/1565 9/00 www.firstalertpro.com Table of Contents: page Introduction...............................
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationInstructions for Using the Watch Works Tool Kit to Change a Watch Battery
Instructions for Using the Watch Works Tool Kit to Change a Watch Battery Click on this link http://www.allamericanwatches.com/site/626101/product/e2306-a to purchase the Watch Battery Replacement Tool
More informationStorTrends 3400 Hardware Guide for Onsite Support
StorTrends 3400 Hardware Guide for Onsite Support MAN-3400-SS 11/21/2012 Copyright 1985-2012 American Megatrends, Inc. All rights reserved. American Megatrends, Inc. 5555 Oakbrook Parkway, Building 200
More informationPackard Bell Easy Repair 1. Packard Bell Easy Repair
Packard Bell Easy Repair Hard Disk Drives Important Safety Check Instructions You must read all instructions carefully before you begin work and comply with the procedures set out below. Failure to comply
More informationSC 7000 and SC 9000XL Patient Monitors SC 9000XL Monitor 12in (30.5cm) Display Service Manual Supplement Two
s SC 7000 and SC 9000XL Patient Monitors SC 9000XL Monitor 12in (30.5cm) Display Service Manual Supplement Two EM Guidelines, 1997-04-02 E331.E539U.640.10.03.02 ASK-A898-03-7600 Page 1 of 16 Service Manual
More informationInstalling Your 960 or 980 Server into a Rackmount Cabinet
Installing Your 960 or 980 Server into a Rackmount Cabinet 1 2 Contents Installing Your Gateway Server into a Rackmount Cabinet...1 Identifyingpartsintheaccessorykit...2 Rackmounthandlekit... 2 Rackmountrailkit...
More informationPart Name/Description Part Number Quantity. Power Cable 4000950-5 1
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Power Cable 4000950-5 1 Raven Harness Adapter Kit 4100525 1 Installation Instructions
More informationipad 2 GSM Headphone Jack & SIM Slot Replacement
ipad 2 GSM Headphone Jack & SIM Slot Replacement Replace the Headphone jack/sim slot in your ipad 2 GSM. Written By: Walter Galan INTRODUCTION Use this guide to replace a broken headphone jack or SIM card
More informationHARDWARE REFERENCE. Gateway Notebook
HARDWARE REFERENCE Gateway Notebook Contents Chapter 1: About this reference...............................................1 About this guide........................................................ 2
More informationReplacing Redundant AC Power Supplies in an EX4500 Ethernet Switch Without Disrupting Service
Replacing Redundant AC Power Supplies in an EX4500 Ethernet Switch Without Disrupting Service This field replacement guide provides instructions for replacing the two AC power supplies in an EX4500 Ethernet
More informationRack Mount Kit Install Guide: Intel Entry Server Chassis SC5295-E UP/DP/WS/BRP Intel Entry Server Chassis SC5299-E DP/WS/BRP
Rack Mount Kit Install Guide: Intel Entry Server Chassis SC5295-E UP/DP/WS/BRP Intel Entry Server Chassis SC5299-E DP/WS/BRP A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/Products
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationPS6500 Storage Arrays Rack Mount Instructions
PS6500 Storage Arrays Rack Mount Instructions Part Number: R724M Rev. A01 Copyright 2010 Dell, Inc. All rights reserved. Dell is a trademark of Dell, Inc. EqualLogic is a registered trademark. All trademarks
More informationNavico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement
Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations
More informationHard Disk Drive (HDD)
Installation Instructions Hard Disk Drive (HDD) Catalog Number 6189V-35HDDST80, 6189V-35HDDST160 Topic Page About This Publication 1 Important User Information 2 Electrostatic Discharge (ESD) Precautions
More informationWINDOW REPAIR MANUAL & REFERENCE GUIDE
WINDOW REPAIR MANUAL & REFERENCE GUIDE TABLE OF CONTENTS DOUBLE HUNG & SINGLE HUNG PARTS 4-5 CASEMENT PARTS 6 SCREEN PARTS 7-8 HOW TO REMOVE TILT-IN SASH 9 HOW TO REMOVE A BALANCE 10 HOW TO INSTALL BALANCE
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationTraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions
TraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions TRACETEK TraceTek TTDM Replacement Parts General Information These instructions detail the steps to
More informationUpgrading or Replacing a Host Interface Card in a Xanadu-230 Controller-Drive Tray
Upgrading or Replacing a Host Interface Card in a Xanadu-230 Controller-Drive Tray ATTENTION Possible equipment damage Only a qualified service technician should perform this procedure, or equipment damage
More informationCopyright 2007 Hewlett-Packard Development Company, L.P. Windows is a U.S. registered trademark of Microsoft Corporation.
Drives User Guide Copyright 2007 Hewlett-Packard Development Company, L.P. Windows is a U.S. registered trademark of Microsoft Corporation. The information contained herein is subject to change without
More informationUPDATEUPDATEUPDATE. Converting the tower chassis to a rack-mount chassis. A - M5 13 8 To mount outer member to rack
UPDATEUPDATEUPDATE Converting the tower chassis to a rack-mount chassis Rail overview Converting your Server to Rack-Mount The rail kit includes the following: Two rail units Five packages of screws (labeled
More informationTeamPoS 2000 Installation Instructions Upgrade to M Motherboard
TeamPoS 2000 Installation Instructions Upgrade to M Motherboard Fujitsu Transaction Solutions Inc. endeavors to ensure that the information in this document is correct and fairly stated but does not accept
More informationTyan Computer. Transport PX22. Service Engineer s Manual
Tyan Computer Transport PX22 Service Engineer s Manual 1 Precaution To read through the user manual, check all assembly and follow setup process before any operation on this server To keep paper clips,
More informationInstalling your upgrade processor
Installing your upgrade processor This processor upgrade kit contains the following: Pentium processor with heat sink attached Processor retention bracket Voltage regulator module (VRM) Electrostatic discharge
More informationMemory Installation Guide
Memory Installation Guide For ASUSTOR 6 Series NAS Ver.1.0.0.1204 Table of Contents 1. Introduction... 3 1.1. Notes and Precautions... 3 1.2. Parts and Tools Needed... 4 2. Installation Guide... 5 2.1.
More informationMazda CX7 2010-up 99-7520B
INSTALLATION INSTRUCTIONS FOR PART 99-7520B APPLICATIONS Mazda CX7 2010-up 99-7520B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More informationProLiant DL380 Generation 2 Server Maintenance and Service Guide
ProLiant DL380 Generation 2 Server Maintenance and Service Guide Second Edition (June 200) Part Number 203840-002 Spare Part Number 228520-00 Compaq Computer Corporation Notice 200 Compaq Computer Corporation
More information4x3.5" Hot-Swap Drive Cage Kit Installation Guide for Intel Server Chassis/System
4x3.5" Hot-Swap Drive Cage Kit Installation Guide for Intel Server Chassis/System Order Number: G23758-002 G23758-002 This document provides instructions for installing the following accessory kit: FUP4X35HSDK
More informationPRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129
PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,
More informationContents. Installing the upgrade memory kit in the G450 and G430 Media Gateway May 2014 1
Contents Installing the upgrade memory kit in the G450 / G430 Media Gateway... 3 Equipment ordering... 3 Inserting or replacing a RAM card... 4 Inserting or replacing a RAM card in the G450... 4 Replacing
More informationInstallation Instructions 4508 4508S
SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationRS Monitor Backlight Replacement
Replacement Instructions The RS Monitor s two backlight bulbs should provide many hours of service. However, if they burn out, you can easily replace them. Note Backlight bulbs tend to have a consistent
More informationBackup Battery Kit Install Guide: Intel Storage Controller AXXSCM3S
Backup Battery Kit Install Guide: Intel Storage Controller AXXSCM3S A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/ Products Intel Order Number: E13860-004 Disclaimer Information
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationInstallation instructions, accessories. Cruise control. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No. 30739998 1.
Instruction No Version Part. No. 30739998 1.1 Cruise control Page 1 / 11 Equipment A0000162 A0000161 A0801178 D8802049 Page 2 / 11 M8802108 Page 3 / 11 IMG-223164 Page 4 / 11 IMG-213320 Page 5 / 11 INTRODUCTION
More information