Stepping motors. Jari Kostamo
|
|
- Clarence Hensley
- 7 years ago
- Views:
Transcription
1 Stepping motors Jari Kostamo
2 Outline Introduction Stepping motor structures Properties of stepping motor Control of stepping motors
3 Stepping motor Stepping motor is an electromechanical device which converts electrical pulses to discrete mechanical translation. Axle of the stepping motor turns in discrete steps when the coils are pulsed with electric current in proper sequence Direction of rotation depends on the sequence of the pulses Angle of rotation is determined by the number of pulses Rotation speed is determined by the frequency of the pulses
4 Stepping motor Typically for small power applications (holding torque in a range of Ncm or power less than 750 W) Low cost Easy to interface with digital control with microcontrollers. Precise control without feedback (step angle as low as 0,5 o ) Can be used with feedback Stepping rated possible up to 40 khz (drive) or 3 khz (pull in freq) Dynamical properties are only moderate due to the operating principle Can lose steps when loaded heavily Operating range may contain problematic areas Achieved position is not perfectly precise but the motor can be displaced with a small torque. Operating is slightly shaking Audible noise due to the stepping
5 Stepping motors Typically 12, 24, 72, 100, 144, 180 or 200 steps per revolution (equal to 30, 15, 5, 3.6, 2.5, 2 or 1.8 degree step angle). With microstepping even steps per revolution can be achieved. Unipolar and bipolar motors. Open control is used if losing steps does not cause critical problems.
6 Magnetic circuit Translation in stepping motor is produced by magnetic forces Magnetic circuit is generated with coils Magnetic field strength depends on the nuber of ampere turns, current and geometry Inductance of the coil creates an opposing voltage proportional to the rate of change in current. Inductance has a tendency to limit the chages in current. Larger voltages are needed if rapid changes are desired. Current control
7 Pulse width modulated control (PWM) Efficient and modern way to control currents of the motor coils is PWM PWM amplifier, chopper, switched mode amplifier... Transistors are rapidly switched on and off ON-state has low resistance OFF state has high resistance Yields to small losses Current is defined by the proportion of the ON and OFF states Can be implemented with uc Dedicated circuits available.
8 Stepping motors Permanent magnet motor Reluctance motor Hybrid motor
9 Variable reluctance stepping motor; VR motor Kenjo, T., Stepping motors and their microprocessor controls
10 Permanent magnet stepping motor; PM motor Kenjo, T., Stepping motors and their microprocessor controls
11 Hybrid stepping motor Kenjo, T., Stepping motors and their microprocessor controls
12 Linear stepping motor Parker Functional principle similar to hybrid motor, 2D motions possible 2D stage: Baldor
13 Stepping motor control example Full stepping (Kirjasta Bolton, Mechatronics) A1 A2 B1 B2 Half stepping A1 A2 B1 B2
14 Half stepping
15 (Book: Fraser & Milne, Integrated Electrical and Electronic Engineering)
16 Dynamical properties of stepping motors Kenjo, T., Stepping motors and their micro-processor controls
17 Holding torque Kenjo, T., Stepping motors and their micro-processor controls
18 Settling time Kenjo, T., Stepping motors and their microprocessor controls If vibration at low speeds is an issue, consider the geared types. Not only does changing gears increase torque, but also these models improve starting and stopping responsiveness.
19 Resonance frequencies Lawrence & Mauch, Real-Time Microcomputer System Design Speed-torque graph
20 Stepping rate Typical stepping profile
21 Control systems for stepping motors Direct computer control Lawrence & Mauch, Real-Time Microcomputer System Design Computer control with stepping circuit Computer control with intelligent indexer
22 Digital linear actuator
Micro-Step Driving for Stepper Motors: A Case Study
Micro-Step Driving for Stepper Motors: A Case Study N. Sedaghati-Mokhtari Graduate Student, School of ECE, University of Tehran, Tehran, Iran n.sedaghati @ece.ut.ac.ir Abstract: In this paper, a case study
More informationStepper motor I/O. Application Note DK9222-0410-0014 Motion Control. A General information on stepper motors
Stepper motor Keywords Stepper motor Fieldbus Microstepping Encoder Phase current Travel distance control Speed interface KL2531 KL2541 Part A of this Application Example provides general information on
More informationPrinciples of Adjustable Frequency Drives
What is an Adjustable Frequency Drive? An adjustable frequency drive is a system for controlling the speed of an AC motor by controlling the frequency of the power supplied to the motor. A basic adjustable
More informationDrive circuit basics + V. τ e. Industrial Circuits Application Note. Winding resistance and inductance
ndustrial Circuits Application Note Drive circuit basics For a given size of a stepper motor, a limited space is available for the windings. n the process of optimizing a stepper motor drive system, an
More informationM.S Ramaiah School of Advanced Studies - Bangalore. On completion of this session, the delegate will understand and be able to appriciate:
Transmission Control Lecture delivered by: Prof. Ashok C.Meti MSRSAS-Bangalore 1 Session Objectives On completion of this session, the delegate will understand and be able to appriciate: Rl Role of electronic
More informationMECE 102 Mechatronics Engineering Orientation
MECE 102 Mechatronics Engineering Orientation Mechatronic System Components Associate Prof. Dr. of Mechatronics Engineering Çankaya University Compulsory Course in Mechatronics Engineering Credits (2/0/2)
More informationPulse Width Modulation Applications
Pulse Width Modulation Applications Lecture 21 EE 383 Microcomputers Learning Objectives What is DTMF? How to use PWM to generate DTMF? How to use PWM to control a servo motor? How to use PWM to control
More informationLecture 24. Inductance and Switching Power Supplies (how your solar charger voltage converter works)
Lecture 24 Inductance and Switching Power Supplies (how your solar charger voltage converter works) Copyright 2014 by Mark Horowitz 1 Roadmap: How Does This Work? 2 Processor Board 3 More Detailed Roadmap
More informationRelationship between large subject matter areas
H02M APPARATUS FOR CONVERSION BETWEEN AC AND AC, BETWEEN AC AND DC, OR BETWEEN DC AND DC, AND FOR USE WITH MAINS OR SIMILAR POWER SUPPLY SYSTEMS; CONVERSION OF DC OR AC INPUT POWER INTO SURGE OUTPUT POWER;
More informationStudy Guide for the Electronics Technician Pre-Employment Examination
Bay Area Rapid Transit District Study Guide for the Electronics Technician Pre-Employment Examination INTRODUCTION The Bay Area Rapid Transit (BART) District makes extensive use of electronics technology
More informationMotor Fundamentals. DC Motor
Motor Fundamentals Before we can examine the function of a drive, we must understand the basic operation of the motor. It is used to convert the electrical energy, supplied by the controller, to mechanical
More informationDC Motor control Reversing
January 2013 DC Motor control Reversing and a "Rotor" which is the rotating part. Basically there are three types of DC Motor available: - Brushed Motor - Brushless Motor - Stepper Motor DC motors Electrical
More informationBALDOR ELECTRIC COMPANY SERVO CONTROL FACTS A HANDBOOK EXPLAINING THE BASICS OF MOTION
BALDOR ELECTRIC COMPANY SERVO CONTROL FACTS A HANDBOOK EXPLAINING THE BASICS OF MOTION MN1205 TABLE OF CONTENTS TYPES OF MOTORS.............. 3 OPEN LOOP/CLOSED LOOP..... 9 WHAT IS A SERVO..............
More informationSynchronous motor. Type. Non-excited motors
Synchronous motor A synchronous electric motor is an AC motor in which the rotation rate of the shaft is synchronized with the frequency of the AC supply current; the rotation period is exactly equal to
More informationEFC 3600. Frequency converters
2 Bosch Rexroth AG Electric Drives and Controls Documentation Compact and complete: space saving side-by-side assembly, plug-in I/O terminals, with brake chopper and mains filter for ultra-simple installation
More informationSimulation and Analysis of PWM Inverter Fed Induction Motor Drive
Simulation and Analysis of PWM Inverter Fed Induction Motor Drive C.S.Sharma, Tali Nagwani Abstract Sinusoidal Pulse Width Modulation variable speed drives are increasingly applied in many new industrial
More informationSpeed Control Methods of Various Types of Speed Control Motors. Kazuya SHIRAHATA
Speed Control Methods of Various Types of Speed Control Motors Kazuya SHIRAHATA Oriental Motor Co., Ltd. offers a wide variety of speed control motors. Our speed control motor packages include the motor,
More informationServo Info and Centering
Info and Centering A servo is a mechanical motorized device that can be instructed to move the output shaft attached to a servo wheel or arm to a specified position. Inside the servo box is a DC motor
More informationLab 8: DC generators: shunt, series, and compounded.
Lab 8: DC generators: shunt, series, and compounded. Objective: to study the properties of DC generators under no-load and full-load conditions; to learn how to connect these generators; to obtain their
More informationTable 1 Comparison of DC, Uni-Polar and Bi-polar Stepper Motors
Electronics Exercise 3: Uni-Polar Stepper Motor Controller / Driver Mechatronics Instructional Laboratory Woodruff School of Mechanical Engineering Georgia Institute of Technology Lab Director: I. Charles
More informationFREQUENCY CONTROLLED AC MOTOR DRIVE
FREQUENCY CONTROLLED AC MOTOR DRIVE 1.0 Features of Standard AC Motors The squirrel cage induction motor is the electrical motor motor type most widely used in industry. This leading position results mainly
More informationSIZE 16 STEPPER MOTOR DATA
SIZE 16 STEPPER MOTOR DATA HY 2 167 6 Rated Phase Current A.6 Phase Resistance 6.6 Phase Inductance mh 8.5 12 8.7 oz.in -s 2 x1 4 lb 1.4 1.6.33 g-cm 2 kg 1. 11.15 Maximum Voltage V 4 Std. No. of Leads
More informationHALL EFFECT SENSING AND APPLICATION
HALL EFFECT SENSING AND APPLICATION MICRO SWITCH Sensing and Control Chapter 1 Hall Effect Sensing Introduction... 1 Hall Effect Sensors... 1 Why use the Hall Effect... 2 Using this Manual... 2 Chapter
More informationDisplay Board Pulse Width Modulation (PWM) Power/Speed Controller Module
Display Board Pulse Width Modulation (PWM) Power/Speed Controller Module RS0 Microcontroller LEDs Motor Control Pushbuttons Purpose: To demonstrate an easy way of using a Freescale RS0K2 microcontroller
More informationConstructing a precision SWR meter and antenna analyzer. Mike Brink HNF, Design Technologist.
Constructing a precision SWR meter and antenna analyzer. Mike Brink HNF, Design Technologist. Abstract. I have been asked to put together a detailed article on a SWR meter. In this article I will deal
More informationPulse Width Modulated (PWM) Drives. AC Drives Using PWM Techniques
Drives AC Drives Using PWM Techniques Power Conversion Unit The block diagram below shows the power conversion unit in Pulse Width Modulated (PWM) drives. In this type of drive, a diode bridge rectifier
More informationInductance. Motors. Generators
Inductance Motors Generators Self-inductance Self-inductance occurs when the changing flux through a circuit arises from the circuit itself. As the current increases, the magnetic flux through a loop due
More informationTransformerless UPS systems and the 9900 By: John Steele, EIT Engineering Manager
Transformerless UPS systems and the 9900 By: John Steele, EIT Engineering Manager Introduction There is a growing trend in the UPS industry to create a highly efficient, more lightweight and smaller UPS
More informationInfluence of PWM Schemes and Commutation Methods. for DC and Brushless Motors and Drives
Influence of PWM Schemes and Commutation Methods for DC and Brushless Motors and Drives Dal Y. Ohm Richard J. Oleksuk Drivetech, Inc. Northrop Grumman Poly-Scientific www.drivetechinc.com Blacksburg, Virginia
More informationCSEN301 Embedded Systems Trimester 1
Victoria University of Wellington (VUW) course offering for NZ-EU Joint Mobility Project Novel Sensing Technologies and Instrumentation in Environmental Climate Change Monitoring 1. General The Victoria
More informationSchool of Technology Field of study Electrical Engineering (0714)
AUTUMN SEMESTER 2016 NOTE! Period Study level ECTS cr Course number Course Attendance required in both semesters Attendance required in both semesters M1 = 1 st year Master M2 = 2 nd year Master 1 M1 6
More informationUsing Arduino Microcontrollers to Sense DC Motor Speed and Position
ECE480 Design Team 3 Using Arduino Microcontrollers to Sense DC Motor Speed and Position Tom Manner April 4, 2011 page 1 of 7 Table of Contents 1. Introduction ----------------------------------------------------------
More informationRotating Machinery Diagnostics & Instrumentation Solutions for Maintenance That Matters www.mbesi.com
13 Aberdeen Way Elgin, SC 29045 Cell (803) 427-0791 VFD Fundamentals & Troubleshooting 19-Feb-2010 By: Timothy S. Irwin, P.E. Sr. Engineer tsi@mbesi.com Rotating Machinery Diagnostics & Instrumentation
More informationHALL EFFECT SENSING AND APPLICATION
HALL EFFECT SENSING AND APPLICATION MICRO SWITCH Sensing and Control 7DEOHRI&RQWHQWV Chapter 1 Hall Effect Sensing Introduction... 1 Hall Effect Sensors... 1 Why use the Hall Effect... 2 Using this Manual...
More informationLINEAR MOTOR CONTROL IN ACTIVE SUSPENSION SYSTEMS
LINEAR MOTOR CONTROL IN ACTIVE SUSPENSION SYSTEMS HONCŮ JAROSLAV, HYNIOVÁ KATEŘINA, STŘÍBRSKÝ ANTONÍN Department of Control Engineering, Faculty of Electrical Engineering, Czech Technical University Karlovo
More informationTOYOTA ELECTRONIC CONTROL TRANSMISSION
Electronic Control Transmission (ECT) The Electronic Control Transmission is an automatic transmission which uses modern electronic control technologies to control the transmission. The transmission itself,
More informationMotor Control. Suppose we wish to use a microprocessor to control a motor - (or to control the load attached to the motor!) Power supply.
Motor Control Suppose we wish to use a microprocessor to control a motor - (or to control the load attached to the motor!) Operator Input CPU digital? D/A, PWM analog voltage Power supply Amplifier linear,
More informationModelling, Simulation and Performance Analysis of A Variable Frequency Drive in Speed Control Of Induction Motor
International Journal of Engineering Inventions e-issn: 78-7461, p-issn: 319-6491 Volume 3, Issue 5 (December 013) PP: 36-41 Modelling, Simulation and Performance Analysis of A Variable Frequency Drive
More informationTechnology for Next-generation Reduced-size High-performance Inverter
Technology for Next-generation Reduced-size High-performance Inverter 28 Technology for Next-generation Reduced-size High-performance Inverter Naoki Kurihara Shuichi Tachihara Kenhachiro Minamide Satoshi
More informationIntroduction to Process Control Actuators
1 Introduction to Process Control Actuators Actuators are the final elements in a control system. They receive a low power command signal and energy input to amplify the command signal as appropriate to
More informationHighly Integrated Controller/Driver for Industrial Motion Control of Stepper Motors
Highly Integrated Controller/Driver for Industrial Motion Control of Stepper Motors By Guido Remmerie and Peter Cox, AMI Semiconductor Introduction : Stepper motors are used more and more in industrial
More information1/22/16. You Tube Video. https://www.youtube.com/watch?v=ympzipfabyw. Definitions. Duty Cycle: on-time per period (specified in per cent)
Definition Pulse Width Modulation (PWM) is simply a way of getting the micro-controller to manage pulsing a pin on and off at a set period and duty cycle. The LPC11U24 has four timers with four match registers
More informationVICOR WHITE PAPER. The Sine Amplitude Converter Topology Provides Superior Efficiency and Power Density in Intermediate Bus Architecture Applications
The Sine Amplitude Converter Topology Provides Superior Efficiency and Power Density in Intermediate Bus Architecture Applications Maurizio Salato, Applications Engineering, Vicor Corporation Contents
More informationPulse Width Modulated (PWM)
Control Technologies Manual PWM AC Drives Revision 1.0 Pulse Width Modulated (PWM) Figure 1.8 shows a block diagram of the power conversion unit in a PWM drive. In this type of drive, a diode bridge rectifier
More informationIntroduction to Linear Actuators: Precision Linear Motion Accomplished Easily and Economically
Introduction to Linear Actuators: Precision Linear Motion Accomplished Easily and Economically Part 1 of 2 When students are trained in classic mechanical engineering, they are taught to construct a system
More informationAMZ-FX Guitar effects. (2007) Mosfet Body Diodes. http://www.muzique.com/news/mosfet-body-diodes/. Accessed 22/12/09.
Pulse width modulation Pulse width modulation is a pulsed DC square wave, commonly used to control the on-off switching of a silicon controlled rectifier via the gate. There are many types of SCR s, most
More informationInduced voltages and Inductance Faraday s Law
Induced voltages and Inductance Faraday s Law concept #1, 4, 5, 8, 13 Problem # 1, 3, 4, 5, 6, 9, 10, 13, 15, 24, 23, 25, 31, 32a, 34, 37, 41, 43, 51, 61 Last chapter we saw that a current produces a magnetic
More informationFrequency Converter Fv
2 Bosch Rexroth AG Electric Drives and Controls Documentation Brake chopper with up to 30 kw continuous braking power Easy to operate and service (detachable fan, LCD operating panel with copy function)
More informationLab 14: 3-phase alternator.
Lab 14: 3-phase alternator. Objective: to obtain the no-load saturation curve of the alternator; to determine the voltage regulation characteristic of the alternator with resistive, capacitive, and inductive
More informationPower Electronic Circuits
Power Electronic Circuits Assoc. Prof. Dr. H. İbrahim OKUMUŞ Karadeniz Technical University Engineering Faculty Department of Electrical And Electronics 1 DC to DC CONVERTER (CHOPPER) General Buck converter
More informationINDUCTION MOTOR PERFORMANCE TESTING WITH AN INVERTER POWER SUPPLY, PART 2
INDUCTION MOTOR PERFORMANCE TESTING WITH AN INVERTER POWER SUPPLY, PART 2 By: R.C. Zowarka T.J. Hotz J.R. Uglum H.E. Jordan 13th Electromagnetic Launch Technology Symposium, Potsdam (Berlin), Germany,
More informationWIND TURBINE TECHNOLOGY
Module 2.2-2 WIND TURBINE TECHNOLOGY Electrical System Gerhard J. Gerdes Workshop on Renewable Energies November 14-25, 2005 Nadi, Republic of the Fiji Islands Contents Module 2.2 Types of generator systems
More informationSHUTTERS WITH EMBEDDED MICROPROCESSORS
SHUTTERS WITH EMBEDDED MICROPROCESSORS S. Stephenson ABSTRACT Shutters are used to periodically provide a non-uniformity correction (NUC) calibration surface to micro bolometers. Many bolometer applications,
More informationAN235 Application note
Application note Stepper motor driving By Thomas Hopkins Introduction Dedicated integrated circuits have dramatically simplified stepper motor driving. To apply these ICs, designers need little specific
More informationKINETIC ENERGY RECOVERY SYSTEM BY MEANS OF FLYWHEEL ENERGY STORAGE
ADVANCED ENGINEERING 3(2009)1, ISSN 1846-5900 KINETIC ENERGY RECOVERY SYSTEM BY MEANS OF FLYWHEEL ENERGY STORAGE Cibulka, J. Abstract: This paper deals with the design of Kinetic Energy Recovery Systems
More informationApplication Information Fully Integrated Hall Effect Motor Driver for Brushless DC Vibration Motor Applications
Application Information Fully Integrated Hall Effect Motor Driver for Brushless DC Vibration Motor Applications By Shaun Milano Vibration motors are used in a variety of applications including mobile phone
More information3-Phase BLDC Motor Control with Hall Sensors Using 56800/E Digital Signal Controllers
Freescale Semiconductor Application Note AN1916 Rev. 2.0, 11/2005 3-Phase BLDC Motor Control with Hall Sensors Using 56800/E Digital Signal Controllers Leonard N. Elevich Contents 1. Application Benefits...1
More informationSECTION 4 ELECTRIC MOTORS UNIT 17: TYPES OF ELECTRIC MOTORS
SECTION 4 ELECTRIC MOTORS UNIT 17: TYPES OF ELECTRIC MOTORS UNIT OBJECTIVES After studying this unit, the reader should be able to Describe the different types of open single-phase motors used to drive
More informationINSTRUMENTATION AND CONTROL TUTORIAL 2 ELECTRIC ACTUATORS
INSTRUMENTATION AND CONTROL TUTORIAL 2 ELECTRIC ACTUATORS This is a stand alone tutorial on electric motors and actuators. The tutorial is of interest to any student studying control systems and in particular
More informationSeries: IDAM Servo Drive E Digital Motor Drive - DMD-078.12
Series: IDAM Servo Drive E Digital Motor Drive - DMD-078.12 inside Integrated amplifiers for 8 single-phase motors, 4 two-phases motors or 4 three-phases motors or combinations of them in one device Position
More informationAN470 APPLICATION NOTE
AN470 APPLICATION NOTE THE L297 STEPPER MOTOR CONTROLLER The L297 integrates all the control circuitry required to control bipolar and unipolar stepper motors. Used with a dual bridge driver such as the
More informationEET272 Worksheet Week 9
EET272 Worksheet Week 9 answer questions 1-5 in preparation for discussion for the quiz on Monday. Finish the rest of the questions for discussion in class on Wednesday. Question 1 Questions AC s are becoming
More informationELECTRICAL ENGINEERING
ELECTRICAL ENGINEERING The master degree programme of Teacher Training in Electronical Engineering is designed to develop graduates competencies in the field of Curriculum Development and Instructional
More informationCE801: Intelligent Systems and Robotics Lecture 3: Actuators and Localisation. Prof. Dr. Hani Hagras
1 CE801: Intelligent Systems and Robotics Lecture 3: Actuators and Localisation Prof. Dr. Hani Hagras Robot Locomotion Robots might want to move in water, in the air, on land, in space.. 2 Most of the
More informationMeasurement of Power in single and 3-Phase Circuits. by : N.K.Bhati
Measurement of Power in single and 3-Phase Circuits by : N.K.Bhati A specifically designed programme for Da Afghanistan Breshna Sherkat (DABS) Afghanistan 1 Areas Covered Under this Module 1. Power in
More information7-41 POWER FACTOR CORRECTION
POWER FTOR CORRECTION INTRODUCTION Modern electronic equipment can create noise that will cause problems with other equipment on the same supply system. To reduce system disturbances it is therefore essential
More informationChapter 20: Permanent Magnet Brushed DC Motor Applications
Chapter 20: Permanent Magnet Brushed DC Motor Applications 20.1: Introduction In Chapter 19, our discussion was focused on motor construction and on characterizing motor behavior and performance. These
More information1. Learn about the 555 timer integrated circuit and applications 2. Apply the 555 timer to build an infrared (IR) transmitter and receiver
Electronics Exercise 2: The 555 Timer and its Applications Mechatronics Instructional Laboratory Woodruff School of Mechanical Engineering Georgia Institute of Technology Lab Director: I. Charles Ume,
More informationBRIEF INFORMATION Angular Position Sensors Single and double sensors
BRIEF INFORMATION Angular Position Sensors Single and double sensors Single or redundant sensors High precision due to internal 14 bit resolution High thermal stability and linearity High insensitivity
More informationOPERATING MANUAL. Table of contents. 2 Phase Stepping Motor Driver 2M542. Rev. A. Introduction page 2. Specifications page 2 Timing chart page 3
2 Phase Stepping Motor Driver 2M542 OPEATING MANUAL Table of contents Introduction page 2 Specifications page 2 Timing chart page 3 Setting page 4 Current set page 4 educe current function page 4 Micro
More informationDiodes have an arrow showing the direction of the flow.
The Big Idea Modern circuitry depends on much more than just resistors and capacitors. The circuits in your computer, cell phone, Ipod depend on circuit elements called diodes, inductors, transistors,
More informationMicrocontroller for Variable Speed BLDC Fan Control System. T.C. Lun System Engineer, Freescale Semiconductor, Inc.
Microcontroller for Variable Speed BLDC Fan Control System T.C. Lun System Engineer, Freescale Semiconductor, Inc. 1 Introduction Portable, feature rich, high-performance and compact in size are typical
More informationUNINTERRUPTIBLE POWER SUPPLIES >9900AUPS UNINTERRUPTIBLE POWER SUPPLIES
UNINTERRUPTIBLE POWER SUPPLIES 9900A >9900AUPS UNINTERRUPTIBLE POWER SUPPLIES 9900A The 9900A UPS system uses the most advanced IGBT in both the converter and inverter with Digital Signal Processor (DSP)
More informationL297 STEPPER MOTOR CONTROLLERS
L297 STEPPER MOTOR CONTROLLERS NORMAL/WAVE DRIVE HALF/FULL STEP MODES CLOCKWISE/ANTICLOCKWISE DIRECTION SWITCHMODE LOAD CURRENT REGULA- TION PROGRAMMABLE LOAD CURRENT FEW EXTERNAL COMPONENTS RESET INPUT
More informationObjectives. Capacitors 262 CHAPTER 5 ENERGY
Objectives Describe a capacitor. Explain how a capacitor stores energy. Define capacitance. Calculate the electrical energy stored in a capacitor. Describe an inductor. Explain how an inductor stores energy.
More informationChen. Vibration Motor. Application note
Vibration Motor Application note Yangyi Chen April 4 th, 2013 1 Table of Contents Pages Executive Summary ---------------------------------------------------------------------------------------- 1 1. Table
More informationHYDRAULIC ARM MODELING VIA MATLAB SIMHYDRAULICS
Engineering MECHANICS, Vol. 16, 2009, No. 4, p. 287 296 287 HYDRAULIC ARM MODELING VIA MATLAB SIMHYDRAULICS Stanislav Věchet, Jiří Krejsa* System modeling is a vital tool for cost reduction and design
More informationPowerFlex Dynamic Braking Resistor Calculator
Application Technique PowerFlex Dynamic Braking Resistor Calculator Catalog Numbers 20A, 20B, 20F, 20G, 22A, 22B Important User Information Solid-state equipment has operational characteristics differing
More informationAN3327 Application note
AN3327 Application note L9942 back EMF stall detection algorithm Introduction The L9942 is an integrated stepper motor driver for bipolar stepper motors used primarily in automotive head lamp leveling.
More informationLine Reactors and AC Drives
Line Reactors and AC Drives Rockwell Automation Mequon Wisconsin Quite often, line and load reactors are installed on AC drives without a solid understanding of why or what the positive and negative consequences
More informationAC Induction Motor Slip What It Is And How To Minimize It
AC Induction Motor Slip What It Is And How To Minimize It Mauri Peltola, ABB Oy, Helsinki, Finland The alternating current (AC) induction motor is often referred to as the workhorse of the industry because
More informationOPTICAL COMMUNICATION BASED STEPPER MOTOR CONTROL USING PULSE WIDTH MODULATION
2011 pp 1-5 OPTICAL COMMUNICATION BASED STEPPER MOTOR CONTROL USING PULSE WIDTH MODULATION Vinayak Abrol* Department of Electronics & Communication, SSGPURC Panjab University Chandigarh, India Votrix13@gmail.com
More informationUNDERSTANDING POWER FACTOR AND INPUT CURRENT HARMONICS IN SWITCHED MODE POWER SUPPLIES
UNDERSTANDING POWER FACTOR AND INPUT CURRENT HARMONICS IN SWITCHED MODE POWER SUPPLIES WHITE PAPER: TW0062 36 Newburgh Road Hackettstown, NJ 07840 Feb 2009 Alan Gobbi About the Author Alan Gobbi Alan Gobbi
More informationEliminate Ripple Current Error from Motor Current Measurement
Eliminate ipple Current Error from Motor Current Measurement Eric Persson, Toshio Takahashi Advanced Development Group International ectifier Corp. U..A. INTODUCTION Most motor drives today use measured
More informationMotors and Generators
Motors and Generators Electro-mechanical devices: convert electrical energy to mechanical motion/work and vice versa Operate on the coupling between currentcarrying conductors and magnetic fields Governed
More informationSimple Electronic Transmission
Simple Electronic Transmission Matthew Whitten Brookhaven College Created with materials from Tom Birch 1 Basically a Hydraulic System An electronic transmission is a hydraulically-operated unit that has
More informationA Flexible Closed Loop PMDC Motor Speed Control System for Precise Positioning
A Flexible Closed Loop PMDC Motor Speed Control System for Precise Positioning Shakil Seeraji Department of Aeronautical Engineering Military Institute of Science and Technology Mirpur Cantonment, Dhaka-1216,
More informationElectronic Speed Variator for a Brushless DC Motor
Electronic Speed Variator for a Brushless DC Motor Jorge M. Jaimes Ponce, Jesús U. Liceaga C., Irma I. Siller A. and Enrique Arévalo Zamudio Abstract In this paper the development of an electronic speed
More informationPhase-Control Alternatives for Single-Phase AC Motors Offer Smart, Low-Cost, Solutions Abstract INTRODUCTION
Phase-Control Alternatives for Single-Phase AC Motors Offer Smart, Low-Cost, Solutions by Howard Abramowitz, Ph.D EE, President, AirCare Automation Inc. Abstract - Single Phase AC motors continue to be
More informationTorque motors. direct drive technology
Torque motors direct drive technology Why Direct Drive Motors? Fast and effective Direct-drive technology in mechanical engineering is defined as the use of actuators which transfer their power directly
More information"($!$* -44 5 6 7.89 .#/ @9019 =3 5.# 19 = 77##.#2 19 79A951 88 "#$%!&#$'$()(!* "!$& %$!$*%!&& +", !"#$$"!"" %&!'""$&(&! )*""! %$"'""+,($" -. *""!
-.#/ @9019 =3 5.# 19 = 77##.#2 19 79A951 88!"#$$"!"" %&!'""$&(&! )*""! %$"'""+,($" -. *""!! /01 234#55 65571 50087( *""!! *5571 *579$+):#;$+#" *579#-;#-( *5791 1' 971 1' 951 1' 1 "#?=" 3 08!08&1@@
More informationDigital Systems Based on Principles and Applications of Electrical Engineering/Rizzoni (McGraw Hill
Digital Systems Based on Principles and Applications of Electrical Engineering/Rizzoni (McGraw Hill Objectives: Analyze the operation of sequential logic circuits. Understand the operation of digital counters.
More informationFundamentals of Inverter Fed Motors
Fundamentals of Inverter Fed Motors Technical Manual 10/02 MN780 Contents Page The Growing Use Of Inverters.................................................................. 1 How Inverters Affect Motors....................................................................
More informationPower Amplifiers. Introduction to Power Amplifiers. Amplifiers. Module 5
Module 5 Amplifiers Introduction to What you ll learn in Module 5. Section 5.0 Introduction to. Understand the Operation of. Section 5.1 Power Transistors & Heat Sinks. Power Transistor Construction. Power
More informationDigital vs. Analogue Control Systems
Digital vs. Analogue Control Systems Presented at the 2011 Annual Meeting of the American College of Medical Physics, Chattanooga, TN, May 1, 2011 Ivan A. Brezovich, PhD, Dept. of Rad Onc, Univ of Alabama
More informationWhite Paper Implementing a Flexible CPLD-Only Digital Dashboard for Automobiles
Introduction White Paper Implementing a Flexible CPLD-Only Digital Dashboard for Automobiles An automotive dashboard acts as a nerve center that consolidates all information pertaining to the safe driving
More informationBi-directional Power System for Laptop Computers
Bi-directional Power System for Laptop Computers Terry L. Cleveland Staff Applications Engineer Microchip Technology Inc. Terry.Cleveland@Microchip.com Abstract- Today the typical laptop computer uses
More informationUser s Manual. For DM542. Fully Digital Stepper Drive. Version 1.0 2012 All Rights Reserved
User s Manual For DM542 Fully Digital Stepper Drive Version 1.0 2012 All Rights Reserved Attention: Please read this manual carefully before using the drive! 3/F, Block 2, Nanyou Tianan Industrial Park,
More informationM860. User s Manual. High Performance Microstepping Drive. For. Version 5.0 2009 All Rights Reserved
User s Manual For M860 High Performance Microstepping Drive Version 5.0 2009 All Rights Reserved Attention: Please read this manual carefully before using the Drive! The content in this manual has been
More informationFlow Charts and Servomotors (background to Lab #2) Things to learn about: flow charts for design. MECH452 2014 Lecture #2 flow charts & servos rev2
MECH 452 Lecture #2 Flow Charts and Servomotors (background to Lab #2) 1 2 Handout #2 (highlights, questions) Things to learn about: flow charts for design Only 5 symbols (subroutine not shown) Flow charts
More information