1996 Volkswagen EuroVan CV
|
|
|
- Shanna Kelley
- 7 years ago
- Views:
Transcription
1 ENGINE COOLING Cooling System Removal & Installation - EuroVan, 2.4L Diesel (AAB & ACV Engine Codes) ENGINE IDENTIFICATION The VIN number ("Code letters" and "Serial number") can be found next to injection pump on left side of cylinder block. See Fig. 1. Additionally there is a sticker on the upper toothed belt guard with "Engine code" and "Serial number". The engine code is also included on the vehicle data plate. See Fig. 2. Fig. 1: Identifying 2.4L Diesel (Engine Codes AAB & ACV) NOTE: On some models, vehicle data plate may be attached to trim cover under lower left side of instrument panel. The engine number consists of up to nine characters (alphanumeric). The first part (maximal 3 characters) 4 января 2005 г. 0:54:38 Page Mitchell Repair Information Company, LLC.
2 makes up the "engine code", and the second part (6 characters), the "serial number". If more than 999,999 engines with the same engine code are produced, the first of the six characters is replaced with a letter. Fig. 2: Locating Vehicle Data Plate BLEEDING COOLING SYSTEM DRAINING 1. Remove cap from coolant expansion tank. See Fig Remove lower sound dampening pan. See SOUND DAMPENING PAN. 3. Drain coolant either via drain plug and coolant hose or via thermostat connection. See Fig января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
3 Fig. 3: Draining Cooling System (2.4L Diesel) FILLING CAUTION: NOTE: If radiator, heat exchanger, cylinder head or cylinder head gasket is replaced, DO NOT reuse old coolant. The cooling system is filled year-round with a mixture of water and antifreeze plus G11 corrosion protection damage agent. G11 and coolant additives will prevent frost and corrosion damage, the formation of chalk and in addition, they raise the coolants' boiling point. For these reasons, the cooling system must be filled year round with anti-freeze and G11. Due to the higher boiling point, the mixture is also an aide to operational efficiency where engines operate at high loads, particularly in tropical climates. For more information, see COOLING SYSTEM SPECIFICATIONS. 1. Open bleeder screw in coolant hose to heater core. 4 января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
4 2. Press down on top of radiator hose. 3. Slowly fill with coolant up to MAX mark on expansion tank. See Fig. 4. Fig. 4: Identifying Expansion Tank MIN & MAX Marks 4. Close bleeder screw in coolant hose to heater core. 5. Start engine and run approximately 1500 RPM for 2 minutes maximum. At same time fill coolant up to over-flow hole on expansion tank. 6. Install expansion tank cap. 7. Run engine until radiator fan comes on at least once. 8. NOTE: When engine is at normal operating temperature, coolant level must be on MAX. When cold, between MIN and MAX marks. Check coolant level and top-off if necessary. 4 января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
5 DRIVE BELTS 2.4L DIESEL (UP TO JANUARY, 1995) The 2.4L diesel engine (up to 1/95) uses of V belts to drive the accessaries. For drive belt routing, see Fig. 5. Removal & Installation (Generator V Belt) 1. Remove lower sound dampening pan. See SOUND DAMPENING PAN. 2. Loosen all securing bolts for tensioning bracket (A) and generator at least one turn. Note it must be possible to move the generator easily by hand. See Fig Replace drive belt. 4. Tension general V belt by turning the tensioning nut (B) with torque wrench. See Fig. 7. Tighten to the appropriate specification using special tool. See Fig. 8. New Belt Tighten to 71 INCH lbs. (8 N.m) Used Belt Tighten to 35 INCH lbs. (4 N.m) 5. Tighten tensioning nut securing nut to 22 ft. lbs. (30 N.m). 6. Tighten generator mounting securing bolt to 26 ft. lbs. (35 N.m). Tighten tensioning bracket to cylinder head/lifting eye to 18 ft. lbs. (25 N.m). 4 января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
6 Fig. 5: Drive Belt Routing (2.4L Diesel - Up To Jan. 1995) 4 января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
7 Fig. 6: Identifying Drive Belt Pulleys, Brackets & Fasteners (2.4L Diesel) 4 января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
8 Fig. 7: Identifying Generator Securing Nut 4 января 2005 г. 0:54:39 Page Mitchell Repair Information Company, LLC.
9 Fig. 8: Ring Insert (1410/2) Required For V Belt Installation 2.4L DIESEL (FROM FEBRUARY, 1995) The 2.4L diesel engine (2/95 and up) uses a single serpentine belt. For drive belt routing, refer to Fig. 11 and Fig. 12. Serpentine belt may also be referred to as a serpentine belt. NOTE: If reusing the serpentine belt, mark the direction of rotation. When installing the belt make sure it is correctly seated in the pulley. Removal & Installation 1. Lift tensioning roller with Lever Tool (3299) and remove serpentine belt from the generator pulley. See Fig. 9. On A/C equipped engines, grasp the serpentine belt with both hands and slowly pull it over power steering pump. See Fig. 14. On all engines, remove belt. 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
10 Fig. 9: Lifting Serpentine Belt Tensioning Roller Using Lever Tool (3299) 2. Before installing the serpentine belt, make sure that all sub-assemblies (generator, power steering pump) are tight. Place serpentine belt on belt pulley with vibration damper. Lift tensioning roller with Lever Tool (3299). Install belt. Slowly release Lever Tool (3299) to re-apply tension to belt. For vehicles with air conditioning, please note the following procedure to install belt: First place the serpentine belt on tensioning roller (1), then on generator (2), idler roller (3), vibration damper (4), idler roller (5) and as far as possible on air conditioner compressor (6). See Fig. 13. Grasp the serpentine belt with both hands and slowly pull it over power steering pump. See Fig. 14. Turn engine over by hand in engine direction of rotation and make sure serpentine belt seats correctly in the running grooves in the belt pulley. 3. For all models, start engine and check belt running. 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
11 Fig. 10: Special Tool Required For Serpentine Belt Installation 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
12 Fig. 11: Serpentine Drive Belt Routing (2.4L Diesel, With A/C) 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
13 Fig. 12: Serpentine Drive Belt Routing (2.4L Diesel, Without A/C) 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
14 Fig. 13: Removing Serpentine Belt (2.4L Diesel, With A/C) 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
15 Fig. 14: Installing Serpentine Belt Onto Power Steering Drive Pulley (2.4L Diesel, With A/C) REMOVAL & INSTALLATION NOTE: The trim frame may also be referred to as lock carrier. FRONT BUMPER Removal & Installation (Up To December, 1995) 1. Pull drive pins out and pull bumper parallel out of guides. See Fig To install, reverse removal procedure. Slide bumper parallel onto guides. Secure by driving in pins. 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
16 Fig. 15: Exploded View Of Bumper Assembly (Up To December, 1995) Removal & Installation (From January, Long Front End) 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
17 1. Remove radiator grille with trim frame. See RADIATOR GRILL & TRIM FRAME. 2. Remove Torx screws (2 and 3). See Fig Disconnect right then left side of bumper beam. See Fig To remove bumper beam, pull beam straight out of guide bracket. 5. To install, reverse removal procedure. Fig. 16: Exploded View Of Front Bumper (From January, Long Front End) 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
18 Removal & Installation (From January, Short Front End) 1. To remove bumper cover, pry out caps (9). See Fig. 17.Remove combination hex screw and washer assemblies (10). Remove Torx screws (8). 2. To remove bumper beam, pull beam straight out of guide bracket. See Fig To install, reverse removal procedure. 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
19 Fig. 17: Exploded View Of Front Bumper (From January, Short Front End) 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
20 RADIATOR & RADIATOR FAN NOTE: The trim frame may also be referred to as lock carrier. Special Tools For radiator fan removal, required special tools. Anti-Freeze Tester Drip Tray (VAG 1306) Spring-Type Clip Pliers (VAG 1921) Torque Wrench (VAG 1331) Removal & Installation Remove lower sound dampening pan. See SOUND DAMPENING PAN. Drain coolant. See DRAINING under BLEEDING COOLING SYSTEM. 1. Remove radiator grill. See RADIATOR GRILL. 2. Remove coolant hoses off radiator using Hose Clip Pliers (VAG 1921). 3. Disconnect connectors off Engine Coolant Temperature (ECT) thermal switch and coolant fan on radiator. 4. On engine code ACV with charge air cooler, remove charge air cooler bracket. See Fig. 26. Remove charge air cooler with air hoses. 5. On all engines, remove radiator grille. See RADIATOR GRILL & TRIM FRAME. 6. Disconnect power steering hydraulic line from radiator(if equipped). For vehicle with A/C, go to step 7. For vehicles without A/C, go to step WARNING: DO NOT open A/C refrigerant circuit. CAUTION: To prevent damage to the condenser, refrigerant lines, pipes, and hoses; ensure that none of them are stretched, kinked, or bent. On vehicles with A/C: Remove A/C fluid reservoir and allow to hang free. Remove clamps from refrigerant lines. Unfasten A/C compressor and condenser and secure to body such that refrigerant lines are not stressed. Go to next step. 8. On all vehicles, unclip radiator securing rubber from lock carrier. Remove lock carrier. 9. Lift out radiator with fans and fan shroud assembly. See Fig. 18 and Fig To install, reverse removal procedures. See TORQUE SPECIFICATIONS. Fill and bleed air from cooling system. Check headlight alignment, if necessary. 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
21 4 января 2005 г. 0:54:40 Page Mitchell Repair Information Company, LLC.
22 Fig. 18: Identifying Radiator & Cooling Fan Assembly Up To December, 1995) 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
23 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
24 Fig. 19: Identifying Radiator & Cooling Fan Assembly (2.5L - January, 1996 & Up) RADIATOR GRILL & TRIM FRAME NOTE: The trim frame may also be referred to as lock carrier. Removal & Installation (Up To December, 1995) 1. Remove mounting screws on left and right sides at upper grill corners. See Fig Tip radiator grill forward and unhook from mounting holes at bottom, remove grill. See Fig To install, reverse removal procedure. Fig. 20: Identifying Mounting Screws (Up To December, 1995) 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
25 Fig. 21: Removing & Installing Radiator Grill (Up To December, 1995) 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
26 Fig. 22: Identifying Radiator Grill Assembly Components (Up To December, 1995) Removal & Installation (Without Trim Frame - From January, 1996) NOTE: Each step in procedure is represented by a number in Fig. 23. Remove coolant hoses off radiator using hose clip pliers (VAG 1921). Disconnect power steering hydraulic line(s) from radiator. 1. Upper radiator grill (1) grill is clipped together with trim frame. 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
27 2. Remove screw/washer assemblies (2). Pull upper radiator grill upward with trim frame. 3. Upper Trim frame (3). Remove with upper radiator grill. 4. Bonded rubber bushing (4). 5. Screw/washer assembly (5). 6. Unlocking lever (6). It is necessary to unlock the corners. 7. Lower trim frame (7). Remove together with bottom radiator grill. 8. Lower radiator grill (8). Lower radiator grill is clipped and screwed together with trim frame. Remove turn signal lights and loosen side latches with unlatching levers (6). Take out combination screw and washer assemblies (5). Pull radiator grill with trim frame up and out. To install, reverse removal procedure. 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
28 Fig. 23: Removal & Installation Radiator Grill (From January, 1996) Removal & Installation (With Trim Frame - From January, 1996) 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
29 NOTE: In order to fold down the radiator, grill with trim frame must be removed. Remove coolant hoses off radiator using hose clip pliers (VAG 1921). Disconnect power steering hydraulic line(s) from radiator. 1. Remove combination screws 2. See Fig Remove (pull out) spray nozzle (5), (if equipped) on left and right side. Hook special (tool 3370) (6) on trim frame below headlight. Pull radiator grill with trim frame (1) off "T" bolt on left and right side. See Fig To install, replace damaged clips 4 before installing radiator with trim frame. Take note to clip radiator grill with trim frame on left and right side at the same time. Continue by reversing removal procedure. 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
30 Fig. 24: Removing & Installing Radiator Grill With Trim Frame (From January, 1996) SERPENTINE BELT TENSIONER 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
31 NOTE: Only for vehicles with tensioning roller. Remove tensioners and bracket only if necessary to remove timing belt covers. Removing & Installing NOTE: When lowering engine, make sure that front exhaust pipe does not lay on steering gear. When pushing the engine forward make sure that the pipes and hoses are not stretched or damaged. 1. Remove lower sound dampening pan. See SOUND DAMPENING PAN. Remove radiator grill. See RADIATOR GRILL. 2. On ACV engine code only, remove charge air cooler. See Fig января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
32 Fig. 25: Exploded View Of Charge Air Cooler (Engine Code ACV) 4 января 2005 г. 0:54:41 Page Mitchell Repair Information Company, LLC.
33 3. On all engines, remove left and right securing bolts and fold lock carrier and radiator out forward. See Fig. 26. Remove power steering line retainers from tensioner bracket and engine mounting. Fig. 26: Identifying Lock Carrier Securing Bolt (Engine Code ACV) 4. Remove serpentine belt using Lever Tool (3299). See DRIVE BELT ROUTING. Unbolt right-hand drive shaft at transmission flange. 5. Bolt Engine Stand (3227) onto cylinder block and tighten bolts to 15 ft. lbs. (20 N.m). Slightly raise engine and transmission using engine and transmission jack. See Fig января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
34 Fig. 27: Installing Engine Support Stand (3227) & Engine/Transmission Jack (VAG 1383 A) 6. On manual transmission, remove front transmission mounts on subframe. See Fig. 28 -Fig января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
35 Fig. 28: Identifying Front Transmission Mount (AAB, Man. Trans. - Up To July, 1992) 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
36 Fig. 29: Identifying Front Transmission Mount (AAB, Man. Trans. - From August, 1992) 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
37 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
38 Fig. 30: Identifying Front Transmission Mount (ACV, Man. Trans.) 7. NOTE: When lowering engine make sure that front exhaust line does not lie on steering gear. When pushing engine forward make sure that cables, lines and hoses are not overstretched. On all engines, remove right-hand engine mount center bolt(s). Lower engine using (VAG 1383 A) engine and transmission jack as far as possible, push forward and prevent from swinging back by mounting with wooden wedge. See Fig. 31. Fig. 31: Showing Placement Of Wooden Wedge To Support Engine 8. Remove serpentine belt relay (idler) roller. Remove serpentine belt tensioning roller. Remove tensioner retainer and engine support assembly complete. See Fig. 32. To install components, reverse sequence of removal. Torque fasteners to specifications. See TORQUE SPECIFICATIONS. 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
39 Fig. 32: Identifying Serpentine Belt Tensioning Components SOUND DAMPENING PAN Removal & Installation 1. Unscrew two hex nuts and six combination hex bolts. See Fig Unhook locking lever. 3. NOTE: On vehicles with automatic transmission or air conditioner, dampening material must be removed according to perforation. See Fig. 34. Swing down dampening pan and unhook at brackets. 4. To install, reverse removal procedures. See TORQUE SPECIFICATIONS. 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
40 Fig. 33: Removing & Installing Sound Dampening Pan 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
41 Fig. 34: Removing & Installing Sound Dampening Material THERMOSTAT Removal & Installation 1. The thermostat housing is located on the left, front side of the cylinder block (behind water pump housing). Remove lower sound dampening pan. See SOUND DAMPENING PAN. 2. Drain coolant. See DRAINING under BLEEDING COOLING SYSTEM. 3. Remove thermostat housing, replace thermostat and gasket. 4. To install, reverse removal procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS. 5. Fill and bleed cooling system. See FILLING under BLEEDING COOLING SYSTEM. Inspect system for leaks. TIMING BELT Special Tools For timing belt service required special tools, see Fig. 35 and Fig января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
42 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
43 Fig. 35: Timing Belt Required Special Tools (1 Of 2) 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
44 4 января 2005 г. 0:54:42 Page Mitchell Repair Information Company, LLC.
45 Fig. 36: Timing Belt Required Special Tools (2 Of 2) Removal (Vehicles Up To January, 1995) NOTE: Engines up to January, 1995 have elongated holes in water pump for tensioning timing belt. 1. Remove sound dampening pan. See SOUND DAMPENING PAN. 2. Remove the front grille. See RADIATOR GRILL.Fold lock carrier with radiator out forward. See Fig Removing generator V See 2.4L DIESEL (UP TO 1/95) under DRIVE BELT ROUTING. Fold generator up fully and secure. Fig. 37: Identifying 2.4L Diesel Timing Belt Components (Up To January, 1995) 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
46 4. Removing V belt for power steering pump. See 2.4L DIESEL (UP TO 1/95) under DRIVE BELT ROUTING. 5. Remove cylinder head cover and timing belt cover for both timing belts. Insert Counter-Hold Tool (T10025) and loosen vibration damper/timing belt pulley by loosening center bolt. See Fig. 38 and Fig. 39. Turn crankshaft to TDC No. 1 cylinder. See Fig января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
47 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
48 Fig. 38: Identifying Cylinder Head Cover & Components Fig. 39: Removing/Installing Vibration Dampener Puller Center Bolt 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
49 Fig. 40: Setting Crankshaft To TDC Cylinder No Remove vibration damper center bolt. Remove the 4 x M8 crankshaft vibration damper and timing belt pulley securing bolts. Remove vibration damper. 7. Release timing belt tension by loosening coolant (water) pump. 8. NOTE: If reusing old timing belt, mark original direction of rotation on belt. Remove lower timing belt cover. Take off timing belt. Installation (Vehicles Up To January, 1995) 1. Check whether TDC mark on flywheel and reference mark are aligned. 2. Lock camshaft with Setting Bar Tool (2065 A). See Fig января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
50 Fig. 41: Locking Camshaft Into Position Using Setting Bar Tool (2065) 3. Center setting bar as follows: Turn camshaft so that one end of setting bar contacts the cylinder head. Using feeler gauge establish the gap at the other end of the setting bar. Place a feeler gauge corresponding to half the gap between setting bar and cylinder head. Turn camshaft until the setting bar contacts the feeler gauge. Place a 2nd feeler gauge, of same thickness, at the other end between setting bar and cylinder head. 4. Loosen camshaft sprocket securing bolt a 1/2 turn. Release camshaft sprocket from camshaft taper by tapping with a hammer (using a drift through rear timing belt cover opening). See Fig января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
51 Fig. 42: Releasing Camshaft Sprocket From Camshaft Tapered End 5. Install timing belt for camshaft drive. Note observe marked direction of rotation for used belt.install lower timing belt cover and also install M8 securing bolt for coolant pump. 6. Adjust timing belt tension by turning coolant pump with Test Unit (VW 210). See Fig. 43. Scale value: Make measurement between coolant pump and camshaft sprocket. Tighten coolant (water) pump securing bolts to 15 ft. lbs. (20 N.m). 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
52 Fig. 43: Adjusting Timing Belt Using Tool (VW210) 7. Tighten lower timing belt cover. Ensure crankshaft is still positioned at TDC No. 1 cylinder, correct if necessary. 8. Tighten camshaft sprocket securing bolt using Counter-Hold Tool (3036). Observe steel type marking on bolt head: Bolts Marked "8.8" Tighten to 63 ft. lbs. (85 N.m) Bolts Marked "10.9" Tighten to 74 ft. lbs. (100 N.m) 9. Take Setting Bar Tool (2065 A) off camshaft. See Fig Insert Counter-Hold Tool (T10025) and tighten crankshaft vibration damper and timing belt pulley center bolt. See Fig Tighten the 4 x M8 crankshaft vibration damper and timing belt pulley securing bolts to 15 ft. lbs. (20 N.m). 12. Install cylinder head cover and timing belt cover. 13. Install power steering pump V belt and adjust. Install generator V belt and adjust. See DRIVE BELT ROUTING. 14. Install lower sound dampening pan. Install radiator with lock carrier. Removal (Vehicles From February, 1995) 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
53 1. Remove serpentine belt. See DRIVE BELTS. 2. Remove radiator grille. See RADIATOR GRILL & TRIM FRAME. 3. For ACV engine code only, remove charge air cooler bracket. See Fig. 26. Remove left and right hand securing bolts. Fold lock carrier and radiator out forward. 4. Remove both timing belt guard and valve cover. See Fig Turn crankshaft to TDC No. 1 cylinder. See Fig. 44. For AAB and ACV (non-synchro) engine codes, marks on injection pump sprocket and console (C) and on flywheel and clutch bell housing (A) or drive plate and clutch bell housing (B) must align. For ACV (synchro) engine code, marks on injection pump sprocket and console (C) and on flywheel and clutch bell housing (A) or drive plate, and clutch bell housing (B) must align. See Fig. 45. Fig. 44: Setting Engine To TDC (AAB & ACV Non-Synchro Engine Codes) 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
54 Fig. 45: Setting Engine To TDC (ACV Synchro Engine Code) 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
55 Fig. 46: Identifying 2.4L Diesel Timing Belt Components (From February, 1995) NOTE: This condition only occurs every 2nd engine rotation at TDC position. 4 января 2005 г. 0:54:43 Page Mitchell Repair Information Company, LLC.
56 6. CAUTION: Manufacturer recommends using NEW center bolt, if removed. On all engines, remove vibration damper bolt. See Fig. 39. Remove lower timing belt guard. 7. If reusing old timing belt, mark belt with arrow indicating original direction of rotation.move tensioning roller and remove timing belt. See Fig. 46. Installation (Vehicles From February, 1995) 1. Check whether TDC mark on flywheel and reference mark are aligned. 2. Lock camshaft with Setting Bar Tool (2065 A). See Fig Center setting bar as follows: Turn camshaft so that one end of setting bar contacts the cylinder head. Using feeler gauge establish the gap at the other end of the setting bar. Place a feeler gauge corresponding to half the gap between setting bar and cylinder head. Turn camshaft until the setting bar contacts the feeler gauge. Place a 2nd feeler gauge, of same thickness, at the other end between setting bar and cylinder head. 4. Loosen camshaft sprocket securing bolt a 1/2 turn. Release camshaft sprocket from camshaft taper by tapping with a hammer (using a drift through rear timing belt cover opening). See Fig Install tensioning roller (1) so that retaining lug locates on the retaining pin (2) on the lower part of the toothed belt guard. See Fig января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
57 Fig. 47: Installing Timing Belt Tensioning Roller (From February, 1995) 6. Install timing belt for camshaft drive. Note observe marked direction of rotation for used belt.tighten tensioning roller securing bolt hand tight. 7. To tighten the toothed belt turn the tensioning roller clockwise with Ring Wrench (3355) until the right edge of indicator (A) aligns with right edge of indicator (B). See Fig. 48. The right edge of indicator (A) must not be rotated past the right edge of indicator (B), otherwise the tensioning roller can be damaged. If it does happen that it is turned too far, the tensioning roller must be fully released and then retightened. You must not turn the eccentric back by purely the amount it has been turned too far. Tighten tensioning roller securing bolt to 15 ft. lbs. (20 N.m). 4 января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
58 Fig. 48: Tensioning Timing Belt (From February, 1995) 8. Ensure crankshaft is still on TDC of No. 1 cylinder. Correct, if necessary. 9. Tighten tensioning roller to specification. See TORQUE SPECIFICATIONS. 10. Tighten camshaft sprocket securing bolt using Counter-Hold Tool (3036). Observe steel type marking on bolt head: Bolts Marked "8.8" Tighten to 63 ft. lbs. (85 N.m) Bolts Marked "10.9" Tighten to 74 ft. lbs. (100 N.m) 11. Remove Setting Bar (2065A) from camshaft. Install lower timing belt guard. Install vibration damper with NEW center bolt. See Fig. 39. Tighten to specification. See TORQUE SPECIFICATIONS. 4 января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
59 12. Tighten the 4 M8 crankshaft vibration damper and toothed belt pulley securing bolts. See TORQUE SPECIFICATIONS. 13. Turn crankshaft two rotations in engine direction of rotation until crankshaft is set to TDC No. 1 cylinder again. Again check the position of the tensioning roller indicator. If the right edges of indicator (A) and (B) do not align, the tensioning procedure must be repeated. See Fig Install timing belt covers. Install cylinder head cover.install serpentine belt. See DRIVE BELTS. 15. Install radiator grille. See RADIATOR GRILL & TRIM FRAME. WATER PUMP NOTE: Water pump is driven the engine timing belt. The water pump may also be referred to as coolant pump. Removal 1. Remove lower sound dampening pan. See SOUND DAMPENING PAN. 2. Drain coolant. See DRAINING under BLEEDING COOLING SYSTEM. 3. Remove radiator grill. See RADIATOR GRILL. 4. Remove timing belt. See TIMING BELT. 5. Remove water pump. Installation CAUTION: If installing re-manufactured water pump, check "O" ring size. Some pumps must be installed with a 5-mm "O" ring. These pumps are identified by a "5" stamped on mounting flange. 1. Install water pump with new "O" ring. Tighten water pump bolts to specification. See TORQUE SPECIFICATIONS. 2. To install remaining components, reverse removal procedure. Fill and bleed cooling system. See FILLING under BLEEDING COOLING SYSTEM. Inspect system for leaks. COOLING SYSTEM SPECIFICATIONS COOLING SYSTEM SPECIFICATIONS COOLING SYSTEM SPECIFICATIONS Application Specification Volume (1) 9.5 Qts. (9.0 L) Cooling Fan Thermal Switch (2) First Stage On F (84-89 C) Off F (76-83 C) Second Stage On F (90-95 C) Off F (82-89 C) 4 января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
60 Run After Cooling Fan Thermal Switch (3) On Off Thermostat (4) Starts To Open Fully Open Opening Stroke Reservoir (Expansion Tank) Cap Opening Pressure 219 F (104 C) 217 F (103 C) 189 F (87 C) 216 F (102 C).28" (7mm) psi ( Bar) (1) Total coolant quantity may vary depending on vehicle equipment. Open bleeder screw in coolant hose to heater core when filling cooling system. (2) Coolant fan thermal switch is located in the right side of the radiator. (3) Run after cooling fan thermal switch is located on the left side of the cylinder head, between the injectors. (4) Thermostat is located on left side of engine block, under lower radiator hose connection housing. Coolant Recommendations When refilling the coolant system only use G 12 VW engine coolant. The frost and corrosion protection additive G 11 must only be used for topping off purposes, when the cooling system is still filled with G 11 (green in color). On no account must G 12 be mixed with other coolant additives! CAUTION: CAUTION: If the fluid in expansion tank is brown, G 12 has been mixed with other coolant. In this case the coolant must be changed. On no account must the coolant additives G 11 and G 12 be mixed. If these additives are mixed it will cause serious engine damage. If the cooling system was filled with G 11 anti-freeze (colored green), before filling with new anti-freeze G 12 (colored red), the cooling system must be flushed out. Remove as much of the coolant remains as is possible from the cooling system. To do this blow compressed air into the coolant expansion tank. Close cooling system and top off with pure water. G 12 (G 11) and coolant additives marked "In accordance with TL VW 774 D (C)" prevent frost and corrosion damage, scaling and also raise boiling point of the coolant. For this reason the system must be filled all year round with frost and corrosion protection additives. Because of its high boiling point, the coolant improves engine reliability under heavy loads, particularly in countries with tropical climates. Protection against frost must be assured to about -25 C (in arctic climatic countries to about -35 C). The coolant concentration must not be reduced by adding water even in warmer seasons and in warmer countries. The anti-freeze ratio must be at least 40%. If for climatic reasons a greater frost protection is required, the amount of G 12 can be increased, but only up to 60% (frost protection to about -40 C), otherwise frost protection is reduced again and cooling effectiveness is also reduced. NOTE: If radiator, heat exchanger, cylinder head or cylinder head gasket has been replaced, do not reuse old coolant. 4 января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
61 TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Component Ft. Lbs. (N.m) Axle Shaft-To-Transmission Flange Bolts (1) 59 (80) Camshaft Sprocket Bolt Bolt Head Marked (85) Bolt Head Marked (100) Center Engine Mounting Bolt (M10 x 60) 48 (65) Coolant Fan Thermo Switch 18 (25) Coolant (Water) Pump-To-Cylinder Block 15 (20) Coolant (Water) Pump Pulley 15 (20) Crankshaft Timing Sprocket Center Bolt Up To Jan., 1995 (2) 339 (460) Crankshaft Timing Sprocket Center Bolt (From Feb., 1995) (3) Step (160) Step 2 Plus 180 Turn Serpentine Idler Roller-To-Tensioner Bracket Bolt 15 (20) Serpentine Belt Tensioner Bracket To-Cylinder Block 51 (70) Serpentine Belt Tensioner Roller-To-Tensioner Lever 15 (20) Timing Belt Tensioner Roller Nut From Feb., (20) Transmission Mount-To-Sub-Frame AAB Engine Code 33 (45) ACV Engine Code (4) Vibration Damper -To-Crankshaft Timing Sprocket (4 Bolts) Up To Jan., (20) Vibration Damper-To-Crankshaft Timing Sprocket (4 Bolts), From Feb Step 1 15 (20) Step 2 Plus 90 Turn INCH Lbs. (N.m) Drain Screw (Coolant) 89 (10) Radiator Mounting Bolt 89 (10) Sound Dampening Pan Hex Nut 80 (9) Timing Belt Covers (M6 Short) (5) 89 (10) Timing Belt Covers (M8 Long) (5) 177 (20) Timing Belt Idler Bolt (5) 89 (10) Timing Belt Inner Covers (5) Thermostat Housing 89 (10) Valve (Cylinder Head) Cover 89 (10) (1) Always use hardness grade 12.9 bolts on axle shaft flange. 4 января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
62 (2) Coat threads and bolt head contact surface with sealing paste AMV , or equivalent. (3) Clean all grease and oil from bolt threads. (4) For torque specification, see Fig. 30. (5) For torque specifications related to timing belt components, also refer to Fig. 37 and Fig января 2005 г. 0:54:44 Page Mitchell Repair Information Company, LLC.
Cooling system components, removing and installing
Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,
Cooling system components, removing and installing
Page 1 of 34 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
Engine, disassembling and assembling
13-1 Engine, disassembling and assembling Note: Replace the oil cooler and thoroughly clean the oil passages if you find metal shavings or larger quantities of small metal particles in the engine oil,
Cooling system components, servicing
19-1 Cooling system components, servicing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate protection, cover the cap
Volkswagen Golf 5 2004-> VW Rabbit GTI 2006->
Стр. 1 из 24 Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> 19-1 Cooling system components Warning! Hot steam may escape when opening expansion tank. Wear protective goggles and protective clothing to prevent
Cooling system components, removing and installing
Volkswagen Touareg 3.2 - Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! Hot steam may escape when opening expansion tank.
Draining and filling cooling system
Page 1 of 9 Draining and filling cooling system Special tools and workshop equipment required Adapter -V.A.G 1274/8- Pipe -V.A.G 1274/10- Drip tray -V.A.G 1306- or drip tray for workshop hoist -VAS 6208-
Volkswagen B3 Passat General-Engine 4 CYL. 19 Engine - Cooling System (Page GR-19)
19 Engine - Cooling System (Page GR-19) Cooling system draining and filling general information Body components, layout Engine components, layout Radiator fan run-on checking Recommended mixture ratios
Cooling system components, removing and installing
Page 1 of 30 19-1 Cooling system components, removing and installing Notes: When the engine is warm the cooling system is under pressure. If necessary release pressure before commencing repair work. Secure
2003 Audi A4. AUDI' '3.0L V6 - AVK Engine - A4 & A6
Installation (A4) CAUTION: Before installation, ensure camshafts are aligned, crankshaft is locked in place and camshaft gear bolts are loose as described in removal procedures. When turning camshaft,
Cooling system components
Page 1 / 33 19-1 Cooling system components Caution! When doing any repair work, especially in the engine compartment, pay attention to the following due to clearance issues: Route lines of all types (e.g.
Cylinder head, removing and replacing
15-1 Cylinder head, removing and replacing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail
Audi > C5 Platform > 1998-2005 4.2 Liter V8 5V Engine Mechanical, Engine Code(s): ART, AWN, BBD 19 - Engine - Cooling system
Page 1 of 5 Audi > C5 Platform > 1998-2005 4.2 Liter V8 5V Engine Mechanical, Engine Code(s): ART, AWN, BBD 19 - Engine - Cooling system Cooling system, draining and filling To prevent frost and corrosion
Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
Rear wheel brakes, servicing. Стр. 1 из 45. Note:
Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly
Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
COOLING SYSTEM Section Page
5 COOLING SYSTEM Section Page 5.1 COOLANT PRE-HEATER... 5-3 5.2 COOLANT PUMP NON-EGR ENGINE... 5-7 5.3 COOLANT PUMP EGR ENGINE... 5-13 5.4 FRONT CONNECTOR HOUSING NON-EGR ENGINE... 5-17 5.5 FRONT CONNECTOR
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)
17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure
Front brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
REMOVAL AND INSTALLATION
303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 15 Engine- Cylinder head, Valvetrain (Page GR-15)
15 Engine- Cylinder head, Valvetrain (Page GR-15) Cylinder head, removing and installing Compression, checking Valve train, servicing Camshaft oil seal, replacing Camshaft, removing and installing Hydraulic
2012 Volkswagen CC Sport. ENGINE 2.0 Liter - Cooling System - Engine Code(s): CBFA & CCTA. 2.0 Liter - Cooling System - Engine Code(s): CBFA & CCTA
19 COOLING SYSTEM GENERAL INFORMATION ENGINE 2.0 Liter - Cooling System - Engine Code(s): CBFA & CCTA COOLANT SYSTEM WARNING: The coolant system is under pressure when the engine is warm. Risk of scalding
Front axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
STEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing
34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism
Turbocharger system components, servicing
21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners
EM 58. 19. REMOVE NO. 2 MANIFOLD STAY (a) Remove the bolt, nut and stay.
57 ROVAL 1. DISCHARGE FUEL SYST PRESSURE (See page FU-9) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery
Cooling System, Draining and Filling. Special tools, testers and auxiliary items required. Adapter V.A.G 1274/8. Drip tray V.A.
Page 1 of 5 Volkswagen > GTI, Rabbit > 2006-2007 2.0 Liter 4-Cyl. 4V Turbo Engine Mechanical, Fuel Injection Ignition, Engine Code(s): BPY 19 - Cooling System Components. Cooling System, Draining and Filling
Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.
Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help
11. COOLING SYSTEM 11-0 COOLING SYSTEM BET & WIN 50
11 COOLING SYSTEM SERVICE INFORMATION------------------------------------------------ 11-1 TROUBLESHOOTING----------------------------------------------------- 11-1 RADIATOR ------------------------------------------------------------------
1993 VOLKSWAGEN ENGINES 2.5L 5-Cylinder. EuroVan
Article Text ARTICLE BEGINNING 1993 VOLKSWAGEN ENGINES 2.5L 5-Cylinder EuroVan * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES
CAM-03, Camshaft Assembly Oil Seal Replacement
CAM-03, Camshaft Assembly Oil Seal Replacement Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft Pin Spanner
2003 ACCORD - Automatic Transmission Removal
2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special
Drive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
Model No: VS4815 1. SAFETY INSTRUCTIONS VS4800 2. INTRODUCTION & APPLICATIONS VS4815 3. CONTENTS. 2.1 Introduction. 2.
Instructions for: Petrol Engine Twin Camshaft Setting / Locking Tool Kit - (incorporating Vanos Alignment) - BMW N42 & N46 Engines Model No: VS4800 Associated kit: Camshaft/Carrier Bracket Remover & Installer
2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net
Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.
ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...
FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE
Cylinder head gasket, replacement
"VCC065612 EN 20110604" 1(7) Cylinder head gasket, replacement Special tools: 999 5098 Disconnect battery earth lead Drain coolant Remove heat shield over exhaust manifold. (Only the two bottom bolts on
1994 Volkswagen Corrado SLC
1994-98 ENGINES Volkswagen 2.8L 6-Cylinder ENGINE IDENTIFICATION NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL
Diesel Turbo Direct Injection (TDI) system, servicing
23-1 Diesel Turbo Direct Injection (TDI) system, servicing The Diesel Direct Fuel Injection (DFI) Engine Control Module (ECM) is equipped with Diagnostic Trouble Code (DTC) memory. Before starting repairs,
Engine. 204-1890 Strobe light, 110V 204-1891 Strobe light, 220V 204-458 Replacement bulb. 204-1057 Compression gauge. 204-166 Dial indicator
The Strobe light checks the unit for: Balance of operating machinery RPM of motors, engine pulleys, fans, etc. Observe belt slippage Strobe light will stop action at speeds from 200 to 6000 RPM 204-1890
Rebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
The cylinder head bolts tightening stages have been updated as listed in Table 1.
NUMBER: 07 EPA04 MBE 4000-6 S.M. REF.: 1.2.2 ENGINE: MBE 4000 DATE: November 2007 SUBJECT: CYLINDER HEAD BOLTS TIGHTENING STAGES PUBLICATION: 6SE412 The cylinder head bolts tightening stages have been
ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Saab 5-Speed Transaxle APPLICATION TRANSMISSION APPLICATION ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Vehicle Application Transmission
Range Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual
Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work
ENGINE COOLING SYSTEM
ENGINE COOLING SYSTEM 1988 Toyota Celica 1987-88 TOYOTA Engine Cooling Systems Celica DESCRIPTION The basic liquid cooling system consists of a radiator, water pump, thermostat, cooling fan, pressure cap,
VS4760.V2. Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines. Model No: 1. SAFETY INSTRUCTIONS
Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines Model No: VS4760.V2 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according
ALLDATA Online - 2006 Dodge Truck RAM 2500 Truck 2WD L6-5.9L DSL Turbo VI... Service and Repair
Page 1 of 15 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2006 Dodge Truck RAM 2500 Truck 2WD L6-5.9L DSL Turbo VIN C Conversion
1/29/2008 DR50. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45
DR50 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR50-001 842645074424 CYLINDER 1 1 2 DR50-002 842645074431
1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43
DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496
Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX
Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX Engine (general) Engine code RF Capacity 1998 (cc) Idle speed 725 ± 25 Valve clearance Valve clearance Cold Inlet 0.25 (mm) Exhaust 0.35 (mm) Compression
1993 SUSPENSION Volkswagen Front. EuroVan
Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Front EuroVan DESCRIPTION FWD independent suspension is an double-wishbone type with torsion bars mounted on upper control arm. Wheel is supported
CHROME FRONT BRAKE MASTER CYLINDER KIT
-J075 REV. 009-0-0 CHROME FRONT BRAKE MASTER CYLINDER KIT GENERAL Kit Number 5-99D, 5-99D Models These Chrome Master Cylinder Kits are designed to replace the original equipment front brake master cylinder
Oregon Fuel Injection
Corporate Office: P.O. Box 21121, VE Pump Removal and Installation Cummins Lock Timed Applications Removal Clean the exterior of the injection pump and mounting surfaces. 1. Disconnect the fuel return
BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > GOKART > BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM) BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)
Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the
Chapter 3 Cooling, heating and air conditioning systems
3 1 Chapter 3 Cooling, heating and air conditioning systems Contents Air conditioner receiver-drier - removal and refitting............ 16 Air conditioning blower motor (E28/ old-shape 5-series models)
TITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
Timing belt replacement intervals
Telephone: Fax: VAT Registration No.: Name: Address: Model: Year: 1994 Registration: Tel - Private: Tel - Business: Mileage: Job number: Important note Important note The intervals and procedures given
VW 2.0T FSI. Timing Belt Installation. This tutorial is provided as a courtesy by ECS Tuning.
VW 2.0T FSI Timing Belt Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all engine vehicles as well
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS SOUCY TRACK SYSTEM 04-M113-1ENS (SPLIT IDLER) Litho d in Canada 1 04-M113-1ENS
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS (SPLIT IDLER) 1 # TABLE OF CONTENTS List of parts and tools................................................3 Installation of complete kit...................................................5
Water Pump Replacement
1 of 8 2/5/2008 6:36 AM Document ID# 713637 2001 Cadillac Seville Print Water Pump Replacement Tools Required 1. J 38816-A Water Pump Remover & Installer 2. J 38185 Hose Clamp Pliers
STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
DR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002 842645048173 GASKET, CYLINDER 1 1 3 DR90-003
Solstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
http://www.passatworld.com/forums/showthread.php?t=166611
Page 1 of 6 For advertising info, email us! Home Forums Passat of the Month Marketplace About Us Passat World Forums > Passat Discussion > Club B5 > B5 Information-Base 1.8T Waterpump/Thermostat Replacement
DO NOT attempt to repair hub and wheel bearing assembly.
Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack
DR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002
illustration ref. no. description SWAG no. RS Kombi, Octavia Scout 4x4, Octavia 4x4 for: Octavia, Octavia Kombi
Skoda protection Kit for strut 20 56 0003 - for: Fabia Skoda protection Kit for strut 30 56 0010 for: Felicia I, Felicia II - Skoda protection Kit for strut 30 56 0029, Octavia Kombi 4x4, Octavia RS, Octavia
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
ENGINE Dinli 904 D1033-011
ENGINE Dinli 904 D1033-011 ENGINE Model Item Part no Description Specification Quantity 01 E140000-01 E14 ENGINE 450C.C. 1 FENDER SEAT D1033-021 FENDER SEAT Model Item Part no Description Specification
Assembly overview - fuel tank
Assembly overview - fuel tank vw-wi://rl/n.en-gb.k02589829.wi::33090894.xml?xsl=3 Page 1 of 2 Assembly overview - fuel tank 1 - Fuel tank 2 - Sleeve When removing, support using engine and gearbox jack
INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05
INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional
AUTO TRANS DIAGNOSIS Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.
AUTO TRANS DIAGNOSIS Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1997-98 AUTOMATIC TRANSMISSIONS Volkswagen Shift Interlock
Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
Stainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
1 5 05-12 5 05-12. Additions, Revisions, or Updates
5 05-12 1 5 05-12 SUBJECT DATE Cylinder Head May 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0023 EPA04 MBE 4000 Cylinder Head Additional
Auxiliary Drive Retrofit (Diesel only) Sprinter Engineering & Compliance Jan-01-2010
Auxiliary Drive Retrofit (Diesel only) Sprinter Engineering & Disclaimer The specifications, descriptions, information, and recommendations contained in this bulletin are believed to be accurate as of
BUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide
BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents
Windshield Wiper System
Volkswagen Golf 5 - Windshield Wiper System Volkswagen Technical Site: http://volkswagen.msk.ru http://vwts.info Page 1 / 15 92-1 Windshield Wiper System General information The windshield wiper system
Kobelco Extended Warranty Program. www.kobelco-europe.com
Kobelco Extended Warranty Program www.kobelco-europe.com Kobelco Extended Warranty is a convenient, value added way to give your Kobelco customers added security and peace of mind. Benefits of the Kobelco
2003 Volkswagen Passat GLX 4Motion
2001-2003 BRAKES Disc MODEL IDENTIFICATION Several different brake versions are used by Volkswagen. To aid in identifying brake system installed on a particular model, see BRAKE SYSTEM IDENTIFICATION table.
3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
Installing a new 928 Motorsports All-Aluminum Radiator
928 Motorsports Supercharger Installation Copyright 2008, 928 Motorsports, LLC All Rights Reserved Installing a new 928 Motorsports All-Aluminum Radiator Copyright 2008 928 Motorsports, LLC. Toll-Free
DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX
This kit may void factory warranty please check with manufacturer.
Mfg Company TM Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using aircraft quality 304 stainless steel and billet aluminum; this EGR kit is designed
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
Fuel Injection Pump, Rotary (005-014)
Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train
13. REAR WHEEL/BRAKE/SUSPENSION
13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...
DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Parts Lists - DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PR... Page 1 of 25 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR125 and DR150 Hensim Dirt
Volkswagen To. Engine Crankshaft, Pistons. www.baumtools.com sales@baumtools.com. 800-848-6657 Toll Free 941-927-1414 Intl' 941-927-1612 Fax
- FLYWHEEL LOCK Locks flywheel in place during removal and installation. Audi - 4, AAN VW - Fox, Dasher, Quantum - CLUTCH PILOT BEARING PULLER Replaced by W88. Audi - 4, 5 984< VW - Vanagon -5 MOUNTING
ENGINE COOLING GENERAL DESCRIPTION 11-1
ENGINE COOLING 11-1 GENERAL DESCRIPTION The cooling system of all 1963 Cadillac engines is of the low capacity type. This is made possible by the small cylinder head area exposed to flame and the high
Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
CO-10 COOLING SYSTEM. Page DESCRIPTION TROUBLESHOOTING CHECK AND REPLACEMENT OF ENGINE COOLANT
CO-1 COOLING SYSTEM DESCRIPTION TROUBLESHOOTING CHECK AND REPLACEMENT OF ENGINE COOLANT WATER PUMP THERMOSTAT RADIATOR Page CO-2 CO-4 CO-4 CO-6 CO-10 CO-12 CO-2 COOLING SYSTEM - Description DESCRIPTION
Operating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
Auto-belay Cable Replacement Process
Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable
AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION
AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION