Bluetooth 2.0+EDR module BM-MP-CS-05 Preliminary Datasheet Data Sheet March 2007 Rev 1.0a

Transcription

1 Bluetooth 2.0+EDR module BM-MP-CS-05 Preliminary Datasheet Data Sheet March 2007 Rev 1.0a Introduction The Bluetooth Class 2 Module (model number BM-MP-CS-05) is a small SMT module with integrated capability of FM radio. This readyto-use Class2 Bluetooth module provides a fully compliant Bluetooth system V2.0+EDR for data and voice communications. The EDR specification provides up to 3Mbits/s throughput. With its tiny size 6.5x5.7x1.4mm the module is suitable for smart handheld devices such as mobile phones and PDA. To improve the performance of both Bluetooth and b/g co-located systems, especially for handheld devices such as mobile phone and PDA, the module provides the capability to support a variety of hardware signalling: 2-wire activity signalling and 3-wire (IEEE) coexistence scheme, AFH, and host passing channel information. The FM radio can be simultaneously operated with Bluetooth. It supports both US/Europe (87.5MHz to 108MHz) and Japanese (76MHz to 90MHz) FM band. It also supports RDS (Radio Data System in Europe or Radio Broadcast Data System in US). Applications Cellular phones Personal Digital Assistant Features Fully compliant with Bluetooth v2.0 system Enhanced Data Rate(EDR) compliant for both 2Mbps & 3Mbps modulation modes With small size suitable for compact system integration. Low power consumption, extend the battery life. Support for b/g Coexistence: Channel skipping, AFH, priority signalling, channel signalling, and host passing.. Superior Performance on mobile phone band rejection - 150db

2 General Description Features Description Standards Fully compliant with Bluetooth TM 2.0+EDR Standard Frequency Band 2.402GHz ~ 2.480GHz Sensitivity dbm (typ) Output Power 0 dbm (typ) with power control (Maximum Power measurement is from chip set) RF Port Impedance 50+/-10Ohm FM Sensitivity -105dbm Condition: Fmod = 1kHz, f = 22.5kHz, (S+N)/N= 26dB, BAF = 300Hz to 15kHz, A-weighted, de-emph = 50 s, fin = 76 to 108MHz Temperature Operating temperature: -30 C to +70 C Storage temperature: -40 C to +85 C Operating Voltage 3.3V DC +/- 10% Power Consumption Basic Data rate: Asynchronous:723.2kbps/57.6kbps (1x) Synchronous:433.9kbps/433.9kbps (1x) Enhance Data Rate: 2Mbps (p/4 DQPSK) 3Mbps (8DPSK) Data Rate Asynchronous:723.2kbps/57.6kbps (1x) Synchronous:433.9kbps/433.9kbps (1x) Interface 38 pin LGA (Land Grid Array) Dimensions Length: 6.5 mm, Width: 5.7 mm, Height: 1.4 mm Recommended Footprint (Top View) 1

3 Pin-assignment Pin Name Description 1 GND Ground 2 FM FM receiver input 3 GND Ground 4 AIO_1 Analog input/output line, can be digitally programmed 5 I2C_Data I 2 C Data 6 I2C_CLK I 2 C Clock 7 Sleep-CLK KHz clock input for watchdog timer 8 AUDIO_R Right channel output for FM analog output 9 AUDIO_L Left channel for FM analog output 10 RST# Reset if low and last at least 5ms 11 GND Ground 12 UART RX UART data input, active high 13 UART RTS UART request to send, active low 14 UART CTS UART clear to send, active low 15 UART RX UART data output, active high 16 SPI_PCM#_SEL Control line to select PCM (low) or SPI (high) 17 GND Ground 18 XTAL1 Crystal connection 19 XTAL2 Crystal connection 20 GND Ground 21 VDD_BT +3.3V 22 * PCM_SYNC; Synchronous data sync; SPI_CS# Chip select for SPI devices, active low 23 * PCM_CLK; Synchronous data clock; SPI_CLK SPI clock 24 * PCM_OUT; Synchronous data output; SPI_MISO SPI output 25 * PCM_IN; Synchronous data input; SPI_MOSI SPI input 26 PIO_0 Programmable digital input/output line 27 PIO_1 Programmable digital input/output line 28 PIO_2 Programmable digital input/output line 29 PIO_3 Programmable digital input/output line 30 GND Ground 31 PIO_4 Programmable digital input/output line 32 GND Ground 33 RF_OUT Bluetooth RF TX/RX 34 GND Ground 35 PIO_5 Programmable digital input/output line 36 PIO_6 Programmable digital input/output line 2

4 37 PIO_7 Programmable digital input/output line 38 PIO_10 Programmable digital input/output line * Note: PCM and SPI interfaces share the same pins. The interface is selected by SPI_PCM#_SEL. Electrical Characteristics Absolute Maximum Ratings Rating Min Max Storage Temperature -40 C +85 C Supply Voltage: VDD -0.40V +3.60V Recommended Operating Conditions Operating Condition Min Max Operating Temperature Range* -30 C +70 C Supply Voltage: VDD +3.0V +3.60V Input/Output Terminal Characteristics Digital Terminals Min Typ Max Unit Input Voltage V IL input logic level low V V IH input logic level high 0.7V DD - V DD +0.4 V Output Voltage V O L output logic level low, (l O = 4.0mA), V VOH output logic level high, (l O = -4.0mA), V DD V USB Terminals Min Typ Max Unit Input threshold V IL input logic level low VDD V V IH input logic level high 0.7 VDD - - V Input leakage current V SS < V IN < V DD µa CI Input capacitance pf Output levels to correctly terminated USB Cable V OL output logic level low V V OH output logic level high V DD V 3

5 For Additional information, please contact the following: Universal Scientific Industrial Co., Ltd. Headquarters 141, Lane 351, Taiping Road, Sec. 1, Tsao-Tuen, Taiwan, Tel: , Fax: , , usi@ms.usi.com.tw 4