Fast-Flo Pump INSTRUCTIONS-PARTS LIST. Table of Contents 1:1 RATIO

Transcription

1 INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts Rev. AA Supersedes Z : RATIO Fast-Flo Pump. MPa,. bar (0 psi) Maximum Air Input Pressure. MPa,. bar (0 psi) Maximum Fluid Working Pressure Refer to page for a list of pump models. Table of Contents Symbols Warnings Pump Models Installation Operation Maintenance Troubleshooting Pump Service Pump Parts Displacement Pump Service Displacement Pump Parts Accessories Dimensions Technical Data Warranty Graco Phone Number A Stubby Pump 07 Bung-Mounted Adjustable Length Pump 076A Bung-Mounted Drum Length Pump GRACO INC. P.O. BOX MINNEAPOLIS, MN 0 Graco Inc. is registered to I.S. EN ISO 900

2 FIRE AND EXPLOSION HAZARD WARNING Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury. Ground the equipment and the object being sprayed. Refer to Grounding the System on page. If there is any static sparking or you feel an electric shock while using this equipment, stop spraying/dispensing immediately. Do not use the equipment until you identify and correct the problem. Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed/dispensed. Keep the spray/dispense area free of debris, including solvent, rags, and gasoline. Electrically disconnect all equipment in the spray/dispense area. Extinguish all open flames or pilot lights in the spray/dispense area. Do not smoke in the spray/dispense area. Do not turn on or off any light switch in the spray/dispense area while operating or if fumes are present. Do not operate a gasoline engine in the spray/dispense area. TOXIC FLUID HAZARD Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed. Know the specific hazards of the fluid you are using. Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines. Any additives to the air supply, such as oil or anti freeze will be exhausted into the atmosphere. Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer. MOVING PARTS HAZARD Moving parts can pinch or amputate your fingers. Keep clear of all moving parts when starting or operating the pump. Before servicing the equipment, follow the Pressure Relief Procedure on page to prevent the equipment from starting unexpectedly.

3 Pump Models UL LISTED PUMPS The following pumps are UL listed for light viscosity paints, lacquers, varnishes, thinners, solvents when installed in accordance with NFPA (National Fire Protection Association) Standards No. 0, Flammable and Combustible Liquids Code, and No. Spray Finishing Using Flammable Materials. The carbon steel pumps are for non-corrosive fluids, and the stainless steel pumps are for corrosives. Stubby Pumps Model No. 6 9 Series B 6 9 Series B 6 9 Series B Displacement Pump No. 96 Series C 97 Series C 9 Series B Description Carbon Steel, Leather Packings Carbon Steel, Polyethylene Packings Stainless Steel, Polyethylene Packings Bung-Mounted Drum Length Pumps Model No Series B 6 9 Series B 6 9 Series B 66 Series A Displacement Pump No. 9 Series D 9 Series D 9 Series B 9 Series D Description Carbon Steel, Leather Packings Carbon Steel, Polyethylene Packings Stainless Steel, Polyethylene Packings Carbon Steel, Polyethylene Packings Parts Pages,, 9, Parts Pages,, 9, 7, 9 Model 66 includes a spout, part no NON-LISTED PUMPS These pumps are for non-corrosive light viscosity fluids such as anti-freeze, windshield washer solvent, ATF, motor oil, and hydraulic oil. Stubby Pumps Model No. 6 9 Series B 6 9 Series B Displacement Pump No. Series A 0 9 Series A Description Carbon Steel, Rubber Packings Stainless Steel, Rubber Packings Bung-Mounted Drum Length Pumps Model No Series B 6 9 Series B 6 9 Series B Displacement Pump No. Series A 6 Series A 0 0 Series A Description Carbon Steel, Rubber Packings Carbon Steel, Rubber Packings Stainless Steel, Rubber Packings Parts Pages,, Parts Pages, 6,, Model 6 9 has a suction tube that can be extended 7 mm ( in.). Non-extended pump length is 7 mm (. in.). Fully extended pump length is 0 mm (6. in.). NON-LISTED PUMPS These pumps are for general fluid transfer applications. Stubby Pumps Model No. 7 0 Series A 7 Series A 7 Series A Displacement Pump No. 7 Series A 7 Series A 7 6 Series A Description Carbon Steel, Leather Packings Carbon Steel, Teflon Packings Stainless Steel, Teflon Packings Parts Pages, 0,, Bung-Mounted Drum Length Pumps Model No. 7 Series A 7 Series A 7 9 Series A Displacement Pump No. 9 Series D 7 9 Series A 7 Series A Description Carbon Steel, Leather Packings Carbon Steel, Teflon Packings Stainless Steel, Teflon Packings Parts Pages,,, 0

4 Installation General Information. The Typical Installation shown in Fig. is only a guide for selecting and installing system components. Contact your Graco distributor for assistance in planning a system to suit your needs. Y. Always use Genuine Graco Parts and Accessories.. Reference numbers and letters in parentheses refer to the callouts in the figures and the parts lists on pages. Grounding the System WARNING FIRE AND EXPLOSION HAZARD This pump must be grounded. Before operating the pump, ground the system as explained below. Also read the section FIRE AND EXPLOSION HAZARD on page. To reduce the risk of static sparking, ground the pump and all other equipment used or located in the pumping area. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Ground all of this equipment.. Pump: connect a ground wire and clamp as shown in Fig.. Loosen the grounding lug locknut (W) and washer (X). Insert one end of a ga (. mm) minimum ground wire (Y) into the slot in the lug (Z) and tighten the locknut securely. Connect the clamp end of the ground wire to a true earth ground. Order Part No Ground Wire and Clamp. Fig. Z 06. Air and fluid hoses: use only electrically conductive hoses.. Air compressor: according to manufacturer s recommendations.. Dispensing valve: grounding is obtained through connection to a properly grounded fluid hose and pump.. Fluid supply container: according to local code. 6. Object being sprayed: according to local code. 7. All solvent pails used when flushing, according to local code. Use only metal pails, which are conductive. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts the grounding continuity. X W

5 Installation D E J L F Model 6 9 only K D CC E J L M H C B A C G mm (0. ) KEY A Vent Plug B Bung Adapter C Air Line Lubricator D Bleed-type Master Air Valve E Air Line Filter F Grounded Air Hose G Fluid Drain Valve H Fluid Outlet J Pin Fitting K Air Control Valve (All Models except 6 9) L Air Line Coupler M Grounded Fluid Hose CC Air Regulator Kit (Model 6 9 only) Fig. 076 Mounting the Pump Always rigidly mount the pump to suit the type of installation planned. Graco mounting accessories are shown in the Accessories section. With 00 liter ( gallon) drum length pumps, screw the bung adapter (B) tightly into the bung hole of the drum and adjust to hold the pump mm (0. in.) off the bottom of the drum. Loosen the vent plug (A) to prevent formation of a vacuum in the drum. Stubby pumps may be mounted on a wall or on the side of a drum with a clamp. Drum pumps can also be mounted to the side of a drum. NOTE: Refer to Dimensions on page for pump dimensions, and air inlet and fluid outlet sizes. If low level cut-off valve 0 6 is being used, install a drum length pump (except Model 6 9) in the container with the valve 0 6 resting on the container bottom. This accessory valve will not fit pumps with a telescoping suction tube, such as Model 6 9. CAUTION If low level cut-off valve 0 6 is used, install it with a strap wrench to avoid damaging the valve. Do not use the legs of the valve to tighten it into the pump.

6 Installation System Accessories Refer to Fig. and the Accessories section. NOTE: To ensure maximum pump performance, be sure that all accessories used are properly sized to meet your system s requirements. Most models are supplied with a needle-type air control valve (K) at the pump air inlet. Model 6 9 is equipped with an air regulator kit (CC) instead (see Fig. ). All models are supplied with an air line quick disconnect coupler (L) to connect the air line to the pump and accessories. WARNING A bleed-type master air valve (D) and a fluid drain valve (G) are required in your system, to help reduce the risk of serious injury, including splashing fluid in the eyes or on the skin, and injury from moving parts if you are adjusting or repairing the pump. Model 6 9 Only Using moderate force, extend the pump suction tube, insert the pump into the drum or tank bung hole, and screw the bung adapter (B) tightly into the bung hole. Lift the pump about mm (0. in.) and tighten the bung adapter (B) screw to hold the pump. Loosen the vent plug (A). Refer to Fig.. CAUTION To prevent damaging the o-ring seals inside the suction tube, do not use excessive force when extending the suction tube. All Other Models Refer to Fig. and to the mounting accessories shown on page 6 for pump mounting methods. Model 6 9 Shown The bleed-type master air valve (D) relieves air trapped between this valve and the pump after the pump is shut off. Trapped air can cause the pump to cycle unexpectedly and result in serious injury, including amputation. Locate the valve close to the pump. The fluid drain valve (G) helps relieve pressure in the displacement pump, hose, and dispensing valve when shutting off the pump. Actuating the dispensing valve to relieve pressure may not be sufficient, especially if there is a clog in the hose or the dispensing valve. CC J L For automatic air motor lubrication, install an air line lubricator (C) downstream from the air regulator (if supplied) and all other accessories. Install a bleed-type master air valve (D) close to the pump. Next, install the air regulator (CC), if supplied. Install an air line filter (E) upstream from all other accessories, to remove harmful dirt and moisture from the compressed air supply. B Using a suitable adapter, install the male disconnect pin fitting (J) in the air filter inlet. Install the air line quick disconnect coupler (L) on the air hose (F), but do not connect it to the pin fitting yet. Connect an electrically conductive fluid hose (M) to the / npt(f) fluid outlet. Fig. 076

7 Operation Pressure Relief Procedure WARNING PRESSURIZED EQUIPMENT HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. To reduce the risk of an injury from accidental spray from the gun, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you: are instructed to relieve the pressure, stop spraying, check or service any of the system equipment, or install or clean the spray nozzle.. Shut off the air to the pump.. Close the bleed-type master air valve (required in your system).. Hold a metal part of the dispensing valve firmly to the side of a grounded metal pail, and trigger the valve to relieve pressure.. Open the fluid drain valve (required in your system) to relieve all fluid pressure, having a container ready to catch the drainage.. Leave the drain valve open until you are ready to dispense again. If you suspect that the nozzle or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the hose end coupling and relieve pressure gradually, then loosen completely. Now clear the nozzle or hose. Flush the Pump Before Using The pump was tested in lightweight oil, which was left in to protect pump parts. To prevent contamination of the fluid you are pumping, flush the pump with a compatible solvent before using it. To flush the pump, connect a short hose to the pump outlet, insert the pump intake into a pail of compatible solvent, direct the hose into a pail, and start the pump as explained at right. Cycle the pump slowly for at least minutes, then stop and disconnect the air hose. Push up on the ball of the intake valve (N) to drain the lower part of the pump. See Fig.. Turn the pump over to drain the upper part of the pump. Fig. Starting and Adjusting the Pump 076 With the air valve (K) or regulator (CC) closed, turn on the air supply and connect the air line coupler (L). See Figs. or. Make sure all dispensing valves are open. Slowly open the air valve (K) or regulator (CC) until the pump cycles to 0 cycles per minute. The pump itself only takes a few strokes to prime. In a large system, however, the pump may have to be cycled for several minutes to fill all the lines. Once the entire system is primed, use the air valve or regulator to control pump speed and cycle rate; always use the lowest pressure necessary to get the desired results. When used for transfer and supply operations with no dispensing valve, the pump will run whenever air is supplied. Pump Shutdown WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure at left.. Disconnect the air line coupler (L).. Relieve the pressure. N

8 Maintenance Fill the wet-cup (P) / full of Graco Throat Seal Liquid (TSL) or compatible solvent and keep it / full to keep fluid from drying on the displacement rod and damaging pump throat packings. See Fig.. Lubricate the throat packings frequently when you are pumping a non-lubricating fluid, or are shutting down for more than a few days. Some pumps have a grease fitting (DD) for this purpose. See Fig.. WARNING Do not attempt to adjust the packing nut with the pump operating. Periodically, check the tightness of the packing nut (P). Relieve the pressure, then tighten enough to prevent leakage; no tighter. See Fig.. If the leakage can not be stopped, change the packings to prevent exposure to the fluid being pumped. The accessory air line lubricator (C) provides automatic air motor lubrication. To manually lubricate the motor, disconnect the air line at the air motor inlet, put about drops of lightweight oil in the inlet, reconnect the air line and turn on the air to blow oil into the motor. L Never allow the pump to run dry of fluid being pumped. A dry pump will quickly accelerate to a high speed, possibly damaging itself. If your pump accelerates quickly, or is running too fast, stop it immediately and check the fluid supply. If the supply container is empty and air has been pumped into the lines, prime the pump and lines with fluid, or flush and leave filled with compatible solvent. Be sure to eliminate all air from the fluid system. P J K WARNING H To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page. Fig. DD 076

9 Troubleshooting WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page.. Relieve the pressure.. Check all other possible remedies before disassembling the pump. PROBLEM CAUSE SOLUTION The pump fails to operate. Dirty or worn air motor. Clean, service; see the separate motor manual The pump operates, but the output is low on both strokes. The pump operates, but the output is low on the downstroke. The pump operates, but the output is low on the upstroke. Inadequate air supply or restricted lines. Closed or clogged air valves. Clogged fluid hose or valve. Worn or damaged valves or seals. Clogged fluid hose or valve. Exhausted fluid supply. Worn or damaged valves or seals. Held open or worn intake valve. Worn or damaged valves or seals. Held open or worn piston valve. Clean lines or increase the air supply (see Technical Data). Open or clear the valves. Clear the hose or valves. Service the valves or seals. Clear the hose or valves. Refill the fluid supply and reprime the pump. Service the valves or seals. Clear or service the valve. Service the valves or seals. Clear or service the valve. Worn or damaged valves or seals. Service the valves or seals. Erratic or accelerated operation. Exhausted fluid supply. Refill the fluid supply and reprime the pump. Broken air motor compression spring. Replace the spring.

10 Pump Service Disconnecting the Air Motor WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page.. Flush the pump. 0. Relieve the pressure. Remove the pump from its mounting.. See Fig. 6. Unscrew the tie rod locknuts (0).. Remove the clip pin (0) and headed pin (0).. Raise the air motor () away from the displacement pump (). Unscrew the displacement rod () from the air motor connecting rod (S). 0 S 0 6. To order pump parts, refer to the parts lists on pages 6. Refer to pages 7 for displacement pump service and parts information. Refer to manual 07 6 for air motor service and parts information. Reconnecting the Air Motor. When reconnecting the air motor, use lithium base grease on the threads of the displacement rod (). Make sure the o-ring () is in place on the rod. 06 T. Insert the muffler (T) into the air motor connecting rod (S) as shown in Fig. 6.. Tighten the displacement rod () into the air motor connecting rod hand tight, and install the pins (0 and 0).. Apply thread sealant to the threads of the tie rods (06). To ensure proper alignment, first thread the tie rod locknuts (06) loosely onto the tie rods, then torque evenly to Nm ( ft lb). Grease the threads. Apply thread sealant. Torque evenly to Nm ( ft lb). NOTE: Removing the muffler (T) will increase both pump flow rate and exhaust noise.. Reconnect the groundwire if it was disconnected during service. Fig

11 Bung Mount Drum-Length Pumps, Carbon Steel Models Pump Parts Model 6 90, Series B, leather packed Model 6 9, Series B, polyethylene packed Model 6 97, Series B, rubber packed Model 7, Series A, leather packed Model 7, Series A, Teflon packed Model 66, Series A, polyethylene packed, with spout 0 0 NUT, lock; M; w/nylon insert PIN, headed, straight PIN, clip TIE ROD FITTING, air line; for Models 7 and 7 only FITTING, air line for all other models NEEDLE VALVE ASSY Includes items 09, 6, PACKING, o-ring; nitrile rubber BODY 66. RING, friction washer NEEDLE 90 6 COUPLER, air line; for Models 7 and 7 only COUPLER, air line for all other models 9 DISPLACEMENT PUMP, for Models 6 90 and 7 ; see page 9 DISPLACEMENT PUMP for Model 6 9; see page DISPLACEMENT PUMP for Model 7 ; see page DISPLACEMENT PUMP for Model 6 97; see page 099 AIR MOTOR KIT See instruction manual NUT, packing KNOB, adjusting 06 6 SPOUT; Model 66 only (not shown) Model 6 90 Shown (Includes items 09, 6, 7; see detail below.) Keep these spare parts on hand to reduce down time.

12 Bung Mount Drum-Length Pumps, Stainless Steel Models Pump Parts Model 6 9, Series B, polyethylene packed Model 6 9, Series B, rubber packed Model 7 9, Series A, Teflon packed 0 96 MOUNTING KIT for Stainless Steel Pumps; includes items 0, 6, NUT, lock; M; w/nylon insert PIN, headed, straight PIN, clip TIE ROD FITTING, air line for Model 7 9 only FITTING, air line for all other models NEEDLE VALVE ASSY Includes items 09, 6, PACKING, o-ring; nitrile rubber BODY 66.. RING, friction washer NEEDLE 90 6 COUPLER, air line; For Model 7 9 only. COUPLER, air line for all other models 9 DISPLACEMENT PUMP For Model 6 9; see page DISPLACEMENT PUMP For Model 6 9; see page 7 DISPLACEMENT PUMP For Model 7 9; see page AIR MOTOR KIT See instruction manual NUT, packing KNOB, adjusting Model 6 9 Shown (Includes items 09, 6, 7; see detail below.) No. 0 Mounting Kit includes items 0, 6, 7. Keep these spare parts on hand to reduce down time. 077A

13 Pump Parts Stubby Length Pumps, Carbon Steel Models Model 6 9, Series B, leather packed Model 6 9, Series B, polyethylene packed Model 6 9, Series B, rubber packed Model 7 0, Series A, leather packed Model 7, Series A, Teflon packed 0 0 NUT, lock; M; w/nylon insert PIN, headed, straight PIN, clip TIE ROD FITTING, air line; For Models 7 0 and 7 only FITTING, air line for all other models NEEDLE VALVE ASSY Includes items 09, 6, PACKING, o-ring; nitrile rubber BODY 66. RING, friction washer NEEDLE 90 6 COUPLER, air line; For Models 7 0 and 7 only COUPLER, air line for all other models 96 DISPLACEMENT PUMP For Model 6 9; see page 97 DISPLACEMENT PUMP For Model 6 9; see page 9 DISPLACEMENT PUMP For Model 6 9; see page 7 DISPLACEMENT PUMP For Model 7 0; see page 0 7 DISPLACEMENT PUMP For Model 7 ; see page 099 AIR MOTOR KIT See instruction manual NUT, packing KNOB, adjusting Model 6 9 Shown (Includes items 09, 6, 7; see detail below.) Keep these spare parts on hand to reduce down time.

14 Pump Parts Stubby Length Pumps, Stainless Steel Models Model 6 9, Series B, polyethylene packed Model 6 9, Series B, rubber packed Model 7, Series A, Teflon packed 0 96 MOUNTING KIT for Stainless Steel Pumps; includes items 0, 6, NUT, lock; M; w/nylon insert PIN, headed, straight PIN, clip TIE ROD FITTING, air line for Model 7 only FITTING, air line for all other models NEEDLE VALVE ASSY Includes items 09, 6, PACKING, o-ring; nitrile rubber BODY 66.. RING, friction washer NEEDLE 90 6 COUPLER, air line; For Model 7 only. COUPLER, air line for all other models 9 DISPLACEMENT PUMP For Model 6 9; see page 0 9 DISPLACEMENT PUMP For Model 6 9; see page 7 6 DISPLACEMENT PUMP For Model 7 ; see page 099 AIR MOTOR KIT See instruction manual NUT, packing KNOB, adjusting Keep these spare parts on hand to reduce down time. Model 6 9 Shown (Includes items 09, 6, 7; see detail below.) No. 0 Mounting Kit includes items 0, 6,

15 Pump Parts Bung Mount Adjustable Length Pump, Carbon Steel Model Fits bung type containers from 7 mm (. in.) to 0 mm (6. in.) deep (maximum 6 mm [ in.] adjustment). Model 6 9, Series B, rubber packed 0 0 NUT, lock; M; w/nylon insert PIN, headed, straight PIN, clip TIE ROD FITTING, air line COUPLER, air line 6 DISPLACEMENT PUMP for Model 6 9; see page 099 AIR MOTOR KIT See instruction manual AIR REGULATOR KIT Includes items 07,, PLUG, pipe; / npt GAUGE, air pressure; 0 60 psi (0 0. MPa, 0. bar); / npt inlet 0 REGULATOR, air; 0 60 psi (0 0. MPa, 0. bar); see NIPPLE, pipe; / npt BUSHING, pipe; / npt(m) x / npt(f) (Includes items 07,, 9 ; see detail below.) Keep these spare parts on hand to reduce down time. 07

16 Displacement Pump Service CARBON STEEL DISPLACEMENT PUMPS, with leather, polyethylene, or Teflon packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 9, page. Model 96, page. Model 9, page 9. Model 97, page 9. Model 7, page 0. Model 7 9, page. Model 7, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kits are available. For best results, use all the new parts in the kit even if the old parts look good. Refer to the parts drawing for your pump. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts. NOTE: On Models 7 and 7, inspect the ball () and seat in the housing () for wear or nicks.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. Loosen the lower nut (6) and unscrew the valve housing () from the connecting rod (7). Unscrew the piston stud ().. Clean and inspect all piston parts. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Screw the piston stud () into the valve housing () and torque to Nm ( ft lb).. When reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0. in.) free travel for the disk (9). Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod () out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the v-packings must face down against fluid pressure. NOTE: On displacement pumps 9, 96, and 7, install the two leather v-packings () below the single Teflon v-packing ().. Leave the packing nut () loose until the displacement rod () has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings.. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.

17 Displacement Pump Parts Model 9 Displacement Pump, Series D 00 Liter ( Gallon) Size, Carbon Steel, Leather Packed Model 96 Displacement Pump, Series C Stubby Size, Carbon Steel, Leather Packed 77 NUT, packing * 7 GLAND, female; stainless steel * 7 7 V-PACKING; Teflon * 7 V-PACKING; leather * 7 GLAND, male; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon 9 BUNG ADAPTER ASSY Includes items 0,, and (used on Model 9 only) BUSHING; nylon 0. SCREW, hex hd; M x. 0. ADAPTER, bung; carbon steel 7 6 CYLINDER (Model 9) 77 6 CYLINDER (Model 96) 77 6 O-RING; Viton 7 9 ROD, displacement NUT, hex; M x ROD, connecting (Model 9) ROD, connecting (Model 96) 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 7 9 CUP, piston; leather 77 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 0, which may be purchased separately. Model 9 Shown * * 6 0 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. Used on Model 9 only. * * * 077

18 Displacement Pump Parts Model 9 Displacement Pump, Series D 00 Liter ( Gallon) Size, Carbon Steel, Polyethylene Packed Model 97 Displacement Pump, Series C Stubby Size, Carbon Steel, Polyethylene Packed 77 NUT, packing * 7 GLAND, female; stainless steel * 77 6 V-PACKING; polyethylene * 7 GLAND, male; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon 9 BUNG ADAPTER ASSY Includes items 0,, and (used on Model 9 only) BUSHING; nylon 0. SCREW, hex hd; M x. 0. ADAPTER, bung; carbon steel 7 6 CYLINDER (Model 9) 77 6 CYLINDER (Model 97) 77 6 O-RING; Viton 7 9 ROD, displacement NUT, hex; M x ROD, connecting (Model 9) ROD, connecting (Model 97) 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 77 9 CUP, piston; polyethylene 77 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 96, which may be purchased separately. Model 9 Shown * * 6 0 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. Used on Model 9 only. * * 077

19 Displacement Pump Parts Model 7 Displacement Pump, Series A Stubby Size, Carbon Steel, Leather Packed 77 NUT, packing * 7 GLAND, female; stainless steel * 7 7 V-PACKING; Teflon * 7 V-PACKING; leather * 7 GLAND, male; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon CYLINDER 77 6 O-RING; Viton 7 9 ROD, displacement NUT, hex; M x ROD, connecting 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 7 9 CUP, piston; leather 77 PISTON, pump 7 9 VALVE, intake PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia. * These parts are included in Repair Kit 0, which may be purchased separately. * * 6 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * 7 6 *

20 Displacement Pump Parts Model 7 9 Displacement Pump, Series A 00 Liter ( Gallon) Size, Carbon Steel, Teflon Packed 77 NUT, packing * 7 GLAND, female; stainless steel * 7 7 V-PACKING; Teflon * 7 GLAND, male; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon 9 BUNG ADAPTER ASSY Includes items 0,, and BUSHING; nylon 0. SCREW, hex hd; M x. 0. ADAPTER, bung; carbon steel 7 6 CYLINDER 77 6 O-RING; Viton 7 9 ROD, displacement NUT, hex; M x ROD, connecting 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 7 9 CUP, piston; Teflon 77 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 0, which may be purchased separately. * * 6 0 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * 077

21 Displacement Pump Parts Model 7 Displacement Pump, Series A Stubby Size, Carbon Steel, Teflon Packed 77 NUT, packing * 7 GLAND, female; stainless steel * 7 7 V-PACKING; Teflon * 7 GLAND, male; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon CYLINDER 77 6 O-RING; Viton 7 9 ROD, displacement NUT, hex; M x ROD, connecting 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 7 9 CUP, piston; Teflon 77 PISTON, pump 7 9 VALVE, intake PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia. * These parts are included in Repair Kit 0, which may be purchased separately. * * 6 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * 7 07

22 Displacement Pump Service CARBON STEEL DISPLACEMENT PUMPS, with rubber packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model, page. Model, page. Model 6, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kit is available. For best results, use all the new parts in the kit even if the old parts look good. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. Loosen the lower nut (6) and unscrew the valve housing () from the connecting rod (7). Unscrew the piston stud ().. Clean and inspect all piston parts. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Screw the piston stud () into the valve housing () and torque to Nm ( ft lb).. When reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0. in.) free travel for the disk (9). Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod () out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the u-cup must face down against fluid pressure.. Leave the packing nut () loose until the displacement rod () has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings.. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.

23 Displacement Pump Parts Model Displacement Pump, Series A 00 Liter ( Gallon) Size, Carbon Steel, Rubber Packed Model Displacement Pump, Series A Stubby Size, Carbon Steel, Rubber Packed 77 NUT, packing * 79 9 BEARING; acetal * 07 PACKING, u-cup; buna-n * 07 7 O-RING; buna-n * 79 9 WASHER; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon 9 BUNG ADAPTER ASSY Includes items 0,, and (used on Model only) BUSHING; nylon 0. SCREW, hex hd; M x. 0. ADAPTER, bung; carbon steel 7 6 CYLINDER (Model ) 77 6 CYLINDER (Model ) 77 6 O-RING; Viton 7 9 ROD, displacement NUT, hex; M x ROD, connecting (Model ) ROD, connecting (Model ) 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 77 9 CUP, piston; polyethylene 77 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit, which may be purchased separately. Model Shown * * * 6 0 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of packing must face up. Used on Model only. Lips of packing must face down. * * 077

24 Displacement Pump Parts Model 6 Displacement Pump, Series A Adjustable Length, Carbon Steel, Rubber Packed 77 NUT, packing * 79 9 BEARING; acetal * 07 PACKING, u-cup; buna-n * 07 7 O-RING; buna-n * 79 9 WASHER; stainless steel 6 7 HOUSING, outlet 7 0 FITTING, grease 0 7 O-RING; Teflon 9 BUNG ADAPTER ASSY Includes items 0,, and BUSHING; nylon 0 SCREW, hex hd; M x. 0 ADAPTER, bung; carbon steel 77 6 CYLINDER 77 6 O-RING; Viton 7 9 ROD, displacement * NUT, hex; M x ROD, connecting 77 6 HOUSING, valve, piston 9 77 VALVE, piston WASHER; stainless steel * 77 9 CUP, piston; polyethylene 77 PISTON, pump 7 0 VALVE, intake BUSHING, pipe; / x / npt 79 9 TUBE, suction, stationary TUBE, suction, movable O-RING; buna-n * These parts are included in Repair Kit, which may be purchased separately. * * * * Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. 07A

25 Displacement Pump Service STAINLESS STEEL DISPLACEMENT PUMPS, with polyethylene, leather, or Teflon packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 9, page 7. Model 9, page. Model 7, page 0. Model 7 6, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kits are available. For best results, use all the new parts in the kit even if the old parts look good. Refer to the parts drawing for your pump. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts.. Inspect the ball () and seat in the housing () for wear or nicks.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. On Models 9 and 7, loosen the lower nut (6) and unscrew the valve housing () from the connecting rod (7). Unscrew the piston stud (). On Models 9 and 7 6, remove the cotter pins (9) from the ball stop pin (0). Remove the ball stop pin and unscrew the piston stud () from the displacement rod (). Be careful not to drop the ball ().. Clean and inspect all piston parts. Be sure to inspect the ball () and its seat on the piston stud () for wear or nicks. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Torque as specified on the applicable illustration. Using a strap wrench, grip the cylinder () near the outlet housing (6) and screw it into the housing. NOTE: On Models 9 and 7, when reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0. in.) free travel for the ball (). Also, when installing the cylinder (), make sure that the knurled end is at the bottom. Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod () out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the v-packings must face down against fluid pressure.. Leave the packing nut () loose until the displacement rod () has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings.. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.

26 Displacement Pump Parts Model 9 Displacement Pump, Series B 00 Liter ( Gallon) Size, Stainless Steel, Polyethylene Packed 0 09 NUT, packing; stainless steel * 7 GLAND, female; stainless steel * 77 6 V-PACKING; polyethylene * 7 GLAND, male; stainless steel HOUSING, outlet 0 7 O-RING; Teflon 9 9 BUNG ADAPTER ASSY Includes items 0,, and BUSHING; nylon 0 7. CAPSCREW; M x ADAPTER, bung; stainless steel 7 6 CYLINDER, gal.; stainless steel 77 6 O-RING; Viton 7 ROD, displacement NUT, hex; M x ROD, connecting 77 7 HOUSING, valve, piston WASHER; stainless steel * 77 9 CUP, piston; polyethylene 7 9 STUD, piston; stainless steel 7 VALVE, intake; stainless steel 7 9 SPACER, piston; Teflon 0 BALL, piston; mm dia PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia. * These parts are included in Repair Kit 96, which may be purchased separately. Torque to 6 Nm (7 ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. Knurl is at the bottom end. * * * * A

27 Displacement Pump Parts Model 9 Displacement Pump, Series B Stubby Size, Stainless Steel, Polyethylene Packed 0 09 NUT, packing; stainless steel * 7 GLAND, female; stainless steel * 77 6 V-PACKING; polyethylene * 7 GLAND, male; stainless steel HOUSING, outlet 0 7 O-RING; Teflon 7 9 CYLINDER, stubby 77 6 O-RING; Viton 7 ROD, displacement WASHER; stainless steel * 77 9 CUP, piston; polyethylene 7 9 STUD, piston 7 VALVE, intake; stainless steel 7 9 SPACER, piston; Teflon 0 BALL, piston; mm dia PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia PIN, cotter PIN, ball stop Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * * * 0 6 * These parts are included in Repair Kit 96, which may be purchased separately. 7 07

28 Displacement Pump Parts Model 7 Displacement Pump, Series A 00 Liter ( Gallon) Size, Stainless Steel, Teflon Packed 0 09 NUT, packing; stainless steel * 7 GLAND, female; stainless steel * 7 7 V-PACKING; Teflon * 7 GLAND, male; stainless steel HOUSING, outlet 0 7 O-RING; Teflon BUSHING; nylon 0 7 CAPSCREW; M x ADAPTER, bung; stainless steel 7 6 CYLINDER, gal.; stainless steel 77 6 O-RING; Viton 7 ROD, displacement NUT, hex; M x ROD, connecting 77 7 HOUSING, valve, piston WASHER; stainless steel * 7 9 CUP, piston; Teflon 7 9 STUD, piston; stainless steel 7 VALVE, intake; stainless steel 7 9 SPACER, piston; Teflon 0 BALL, piston; mm dia PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia. * These parts are included in Repair Kit 0, which may be purchased separately. Torque to 6 Nm (7 ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. Knurl is at the bottom end. * * * * A

29 Displacement Pump Parts Model 7 6 Displacement Pump, Series A Stubby Size, Stainless Steel, Teflon Packed 0 09 NUT, packing; stainless steel * 7 GLAND, female; stainless steel * 7 7 V-PACKING; Teflon * 7 GLAND, male; stainless steel HOUSING, outlet 0 7 O-RING; Teflon 7 9 CYLINDER, stubby 77 6 O-RING; Viton 7 ROD, displacement WASHER; stainless steel * 7 9 CUP, piston; Teflon 7 9 STUD, piston 7 VALVE, intake; stainless steel 7 9 SPACER, piston; Teflon 0 BALL, piston; mm dia PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia PIN, cotter PIN, ball stop Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * * * 0 6 * These parts are included in Repair Kit 0, which may be purchased separately. 7 07

30 Displacement Pump Service STAINLESS STEEL DISPLACEMENT PUMPS, with rubber packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 0 0, page. Model 0 9, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kit is available. For best results, use all the new parts in the kit even if the old parts look good. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts.. Inspect the ball () and seat in the housing () for wear or nicks.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. On Model 0 0, loosen the lower nut (6) and unscrew the valve housing () from the connecting rod (7). Unscrew the piston stud (). On Model 0 9, remove the cotter pins (9) from the ball stop pin (0). Remove the ball stop pin and unscrew the piston stud () from the displacement rod (). Be careful not to drop the ball ().. Clean and inspect all piston parts. Be sure to inspect the ball () and its seat on the piston stud () for wear or nicks. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Torque as specified on the applicable illustration. Using a strap wrench, grip the cylinder () near the outlet housing (6) and screw it into the housing. NOTE: On Model 0 0, when reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0. in.) free travel for the ball (). Also, when installing the cylinder (), make sure that the knurled end is at the bottom. Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod () out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the u-cup must face down against fluid pressure.. Leave the packing nut () loose until the displacement rod () has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings.. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.

31 Displacement Pump Parts Model 0 0 Displacement Pump, Series A 00 Liter ( Gallon) Size, Stainless Steel, Rubber Packed 0 09 NUT, packing; stainless steel * 79 9 BEARING; acetal * 07 PACKING, u-cup; rubber * 07 7 O-RING; buna-n * 79 9 WASHER; stainless steel HOUSING, outlet 0 7 O-RING; Teflon 9 9 BUNG ADAPTER ASSY Includes items 0,, and BUSHING; nylon 0 7. CAPSCREW; M x ADAPTER, bung; stainless steel 7 6 CYLINDER, gal.; stainless steel 77 6 O-RING; Viton 7 ROD, displacement NUT, hex; M x ROD, connecting 77 7 HOUSING, valve, piston WASHER; stainless steel * 77 9 CUP, piston; polyethylene 7 9 STUD, piston; stainless steel 7 VALVE, intake; stainless steel 7 9 SPACER, piston; Teflon 0 BALL, piston; mm dia PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia. Torque to 6 Nm (7 ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. Knurl is at the bottom end. * * * * * 7 * These parts are included in Repair Kit, which may be purchased separately A

32 Displacement Pump Parts Model 0 9 Displacement Pump, Series A Stubby Size, Stainless Steel, Rubber Packed 0 09 NUT, packing; stainless steel * 79 9 BEARING; acetal * 07 PACKING, u-cup; rubber * 07 7 O-RING; buna-n * 79 9 WASHER; stainless steel HOUSING, outlet 0 7 O-RING; Teflon 7 9 CYLINDER, stubby 77 6 O-RING; Viton 7 ROD, displacement WASHER; stainless steel * 77 9 CUP, piston; polyethylene 7 9 STUD, piston 7 VALVE, intake; stainless steel 7 9 SPACER, piston; Teflon 0 BALL, piston; mm dia PIN, ball stop GUIDE, ball 0 6 BALL, intake; mm dia PIN, cotter PIN, ball stop * These parts are included in Repair Kit, which may be purchased separately. Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * * * *

33 Accessories 0 Wall Mounting Bracket Carbon Steel. See manual SCREW, hex hd cap; M x. 0 7 LOCKWASHER, spring, Size 7 0 BUSHING 7 BRACKET 7 9 CLAMP Bung Adapters Included with all 0 liter ( gallon) drum size pumps. Carbon Steel 9 Stainless Steel 0 SCREW, hex hd cap; M x.;cst 0 7 SCREW, hex hd cap; M x.;sst 7 0 BUSHING, nylon 0 ADAPTER, bung, cst 0 77 ADAPTER, bung, sst 0 0 Open Tank Mounting Clamp Carbon Steel. 0 7 SCREW, hex hd cap; M x. 0 7 LOCKWASHER, spring, Size 9 06 PAD, screw mounting 9 07 RETAINER 7 0 BUSHING BRACKET CLAMP 0 79 HANDLE, tee Low Level Cut-Off Valve For installation instructions, see page RING, retaining 6 69 FLOAT 6 60 SPRING, extension 7 HOUSING, valve 0 VALVE, clapper 099 Suction Kit 0 liter ( gallon) drum size for use with Stubby pumps; includes check valve. Carbon steel. 0 liter/min ( gpm) Maximum Suction Rate 0 96 BUSHING, pipe; / npt(m) x / npt(f) 0 7 O RING, Teflon 96 HOSE, / ID; cpld / npt(mbe);. m (6 ft) long; w/spring guard 7 0 HOUSING 7 6 CYLINDER HEAD, suction tube 0 SCREW, hex hd cap; M x BUSHING, nylon 0 0 ADAPTER, bung 60 7 UNION, 90; / npt(m) x / npsm swivel 6 9 0

34 Accessories 7 69 Ground Wire and Clamp 7.6 m ( ft) long Oil Flow Regulator. MPa, bar (00 psi) Maximum Working Pressure / npt(m) x / npt(f) Throat Seal Liquid (TSL) Solvent for wet-cup. 0. liter ( oz.). Bleed-Type Master Air Valve (Required). MPa, bar (00 psi) Maximum Working Pressure Relieves air trapped in the air line between the pump air inlet and this valve when closed. 07 / npt(m x f) inlet and outlet. 07 / npt(m x f) inlet and outlet. 0 7 Drum Cover 0 liter (0 gallon) size and 60 liter (6 gallon) size. Drum cover mounts on top of an open drum, with mounting holes for : metric pump. Includes thumbscrews and a rubber gasket Drum Cover 00 liter ( gallon) size. Drum cover mounts on top of an open drum, with mounting for : metric pump Y Line Strainer. MPa, bar (00 psi) Maximum Working Pressure / npt(f) ports; no. 0 mesh screen Air LIne Filter. MPa, bar (0 psi) Maximum Working Pressure / npt(f) inlet and outlet Spout For directing fluid into pails. Carbon steel; / npt inlet. Air LIne Lubricator. MPa, bar (0 psi) Maximum Working Pressure / npt(f) inlet and outlet. 96 Intake Extension Tube Intake tube 6 mm (0. in.) long; screws into bottom / npt(f) thread of : metric pump. Carbon steel. See manual Air Regulator Kit Includes / size, 0 0. MPa, 0. bar (0 60 psi) air regulator and air pressure gauge, and air quick coupler. See page Hose and Valve. MPa, bar (7 psi) Maximum Working Pressure 7.6 m ( ft) long, / npt(m) x / npt(m), electrically conductive.