INDEX. Parking Sensor Attachment Kit... 1 Sensor/Adaptor Kit (NORMAL/TYPE-S BUMPER)... 3 Sensor/Adaptor Kit (AERO BUMPER)... 3

Transcription

1 INSTALLATION INSTRUCTIONS REAR PARKING ACCORD FEB Parts List INDEX Parking Sensor Attachment Kit... 1 Sensor/Adaptor Kit (NORMAL/TYPE-S BUMPER)... 3 Sensor/Adaptor Kit (AERO BUMPER)... 3 Tools and Supplies Required... 3 Before You Begin Customer Information... 3 Wire Harness Routing Precautions... 4 How To Install The Joint Connector Case and Cover... 5 Illustration of the Components on the Vehicle... 6 Installation Removing the Vehicle Parts... 6 Installing the Sensor Harness... 9 Installing the Sensor Check After Installation Sequence for Self-Diagnostic and Loudness Setting Parts List Parking Sensor Attachment Kit Control unit Rings (4) Spring housings (4) Buzzer 2-Pin connector Self-tapping screw Honda Access Corp / 36

2 Buzzer bracket Sensor harness Sub harness Flange bolts (5) Flange nuts (3) Unit bracket (Some may not used.) (Some may not used.) Wire ties (22) Cushion tapes Harness tapes (6) Joint connector cover Joint connector case Wire tie with clip Fuse label Template Connector clip Ground bolt Owner s manual 2 / 36

3 Sensor/Adaptor Kit (NORMAL/TYPE-S BUMPER) Sensors (4) Bumper adaptors (4) Sensor/Adaptor Kit (AERO BUMPER) Sensors (4) Bumper adaptors A (2) Bumper adaptors B (2) Tools and Supplies Required Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket 8 mm and 10 mm Wrench Scissors Insulating tape Blanket Nippers Pliers Pushpin Drill 3 mm Drill bit 26 mm Hole saw Scraper Tape Eye protection (safety goggles, face shield, etc.) Contact cleaner Shop towel Felt-tip pen Before You Begin Customer Information Write down the customer s radio station presets; the radio memory will be erased when you disconnect the battery. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. Disconnect the negative cable from the battery. Before removing parts from the vehicle, note their locations so that they can be reinstalled in their original places properly. Be sure to use the bolts, screws and nuts included in this kit. Use of bolts, nuts and screws other than those included in this kit may damage the parts. Do not clamp the accessory harness and SRS harness together. 3 / 36

4 Wire Harness Routing Precautions Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector Do not pull the harness with force. It will damage the harness. Cut off the excess of the wire ties. Connect the connectors and terminals securely until they lock. Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays. Take care not to pinch the harness with the vehicle parts during assembly. Secure the harness to the vehicle harness securely not to let them hang down. Reinstall the clamps of the vehicle if they are removed. 4 / 36

5 How To Install The Joint Connector Case and Cover 1. Insert the end of the wire to be connected into the hole in the connector case; then bend and push the remaining section of the wire into the groove in the connector case. Lay the existing wire to which the wire is to be connected in the remaining groove in the connector case, as shown. WIRE from the accessory to be newly installed HOLE Push into the groove in the connector case GROOVE EXISTING WIRE to which the wire from the new accessory is to be connected WIRE from the accessory to be newly installed JOINT CONNECTOR CASE JOINT CONNECTOR CASE 2. Place the connector cover over the connector case and push it to the first lock position by your hand. Finally squeeze the cover all the way to the second lock position with a pair of pliers. When squeezing the connector cover to the second lock position with a pair of pliers Do not pinch any wires with the pliers. After installing the joint connector case and cover, visually check the position of the tabs on both sides of the joint connector case. JOINT CONNECTOR COVER JOINT CONNECTOR CASE TABS OF THE SECOND LOCK POSITION: Press down on the center of the cover SECOND LOCK POSITION Be sure to apply the pliers to the centers of the connector cover and case as shown. CORRECT INCORRECT When the wire from the new accessory is connected to a wrong wire Do not separate the joint connector case and cover once they are installed. Observe the following when you have connected the accessories wire to the wrong cars harness: Cut the accessories wire at a point about 40 mm away from the connector cover. To prevent shortage, bend the end, then wrap an insulation tape around it as shown. Reconnect the accessories wire to the correct cars harness wire using new connector cover and case. New joint connector cover and case are available through your Honda car dealer. INSULATION TAPE Wire from the accessory to be newly installed Bend the end and wrap an insulation tape around it as shown. 5 / 36

6 Illustration of the Components on the Vehicle BUZZER CONTROL UNIT 2A FUSE SUB AH Installation Removing the Vehicle Parts 1. Open the trunk, and remove the two caps and two bolts from the rear bumper. 2. Remove the three clips and ten self-tapping screws from the rear bumper. REAR BUMPER 2 CAPS 2 BOLTS 10 SELF-TAPPING SCREWS 3 CLIPS CT 6 / 36

7 3. Remove the rear bumper. Have an assistant help you when removing and installing the rear bumper. Place the rear bumper on the blanket to prevent damage. TAB REAR BUMPER REAR BUMPER BH 4. Pull the left and right rear seatback lock openers to tip over the left and right rear seatbacks forward. LEFT REAR SEATBACK Tip over forward. TRUNK COMPARTMENT RIGHT REAR SEATBACK Tip over forward. LEFT REAR SEATBACK LOCK OPENER Pull. RIGHT REAR SEATBACK LOCK OPENER Pull AH 5. Remove the trunk floor mat (two clips). 2 CLIPS TRUNK FLOOR MAT T 7 / 36

8 6. Pull away the weatherstrip, and remove the rear trim panel (five clips and two hooks). CLIP 4 CLIPS 2 HOOKS REAR TRIM PANEL WEATHERSTRIP BT 7. Pull away the weatherstrip, and remove the left trunk side trim panel (five clips and two hooks). 4 CLIPS CLIP WEATHERSTRIP LEFT TRUNK SIDE TRIM PANEL HOOK HOOK BT 8. Pull away the weatherstrip, and remove the right trunk side trim panel (five clips and two hooks). 4 CLIPS CLIP WEATHERSTRIP RIGHT TRUNK SIDE TRIM PANEL HOOK HOOK BT 8 / 36

9 9. Using a flat-tip screwdriver wrapped with a shop towel, remove the left rear speaker grille (two clips, four pawls and two hooks). 2 HOOKS LEFT REAR SPEAKER GRILLE 2 CLIPS 4 PAWLS LEFT REAR SPEAKER AH Installing the Sensor Harness 10. Attach the 2A rear sensor fuse label to the fuse case of the sensor harness. FUSE CASE 2A REAR FUSE LABEL AH 11. Install the unit bracket on the control unit using two flange bolts. CONTROL UNIT 2 FLANGE BOLTS UNIT BRACKET AH 9 / 36

10 <With sunroof> 12. Release the clip of the drain tube from the vehicle panel. CLIP DRAIN TUBE PANEL AH 13. Route the two sensor harness 12-pin connectors to the vehicle panel as shown. With sunroof: Route the sensor harness between the vehicle panel and drain tube. <With sunroof> 14. Reinstall the clip of the drain tube that you removed in step 12. PANEL DRAIN TUBE 2 12-PIN CONNECTORS PANEL WITH SUNROOF CH 10 / 36

11 15. Plug the two sensor harness 12-pin connectors into the control unit. CONTROL UNIT 2 12-PIN CONNECTORS CH 16. Install the unit bracket. <Without LKAS unit> a. Install the unit bracket on the vehicle panel using two flange bolts and two flange nuts. 2 FLANGE NUTS UNIT BRACKET 2 FLANGE BOLTS PANEL AH 11 / 36

12 <With LKAS unit> a. Loosen the two vehicle bolts. b. Install the unit bracket between the vehicle panel and LKAS unit bracket and tighten the two vehicle bolts. UNIT BRACKET PANEL BOLT LKAS UNIT BRACKET UNIT BRACKET UNIT BRACKET BH 17. Install the wire tie with clip on the green tape of the sensor harness, and secure the sensor harness to the vehicle panel using one wire tie with clip. <With trailer hitch harness> a. Disconnect the trailer hitch harness 10-pin connector from the trailer unit. b. Release the trailer hitch harness relay block from the trailer hitch unit bracket. c. Align the green tape of the sensor harness with the trailer hitch harness clip, and secure the sensor harness to the trailer hitch harness using one wire tie with clip. d. Plug the trailer hitch harness 10-pin connector into the trailer unit. e. Attach the trailer hitch harness relay block to the trailer hitch unit bracket. WIRE TIE WITH CLIP GREEN TAPE <WITH TRAILER HITCH > GREEN TAPE Align. TRAILER HITCH CLIP WIRE TIE WITH CLIP PANEL BH 12 / 36

13 18. Install the buzzer bracket on the buzzer using one self-tapping screw. SELF-TAPPING SCREW BUZZER BRACKET BUZZER BH 19. Route the buzzer harness down through the hole in the vehicle panel as shown. 20. Install the buzzer bracket on the vehicle panel using one flange bolt and one flange nut. FLANGE BOLT BUZZER BRACKET LEFT REAR SPEAKER BUZZER FLANGE NUT PANEL AH 13 / 36

14 21. Insert the two buzzer harness terminals into the 2-pin connector as shown and lock the connector. LEFT REAR SPEAKER LOCK BROWN/ RED WIRE 2-PIN CONNECTOR 2-PIN CONNECTOR BROWN WIRE BROWN/ RED WIRE 2 BUZZER TERMINALS BROWN WIRE SIDE VIEW AH 22. Using scissors, cut one cushion tape in half. Wrap the halved cushion tape around the buzzer harness 2-pin connector. 23. Connect the sensor harness 2-pin connector into the buzzer harness 2-pin connector. CUSHION TAPE Cut in half. HALF CUSHION TAPE 2-PIN CONNECTOR BUZZER 2-PIN CONNECTOR BH 14 / 36

15 24. Secure the sensor harness and the buzzer harness to the vehicle harness using five wire ties. BUZZER 5 WIRE TIES CLIP AH <Without vehicle harness> 25. Remove the vehicle grommet. GROMMET PANEL 7N0601BH <With vehicle harness> a. Release the vehicle connector from the vehicle panel. b. Release the vehicle harness grommet from the vehicle panel, and draw the vehicle harness into the trunk room. CONNECTOR PANEL PANEL GROMMET AH 15 / 36

16 26. Pass the sensor harness through the grommet hole and install the sensor harness grommet. GROMMET AH 27. Attach the sensor harness ground terminal to the vehicle panel, and install the ground bolt. PANEL GROUND TERMINAL GROUND BOLT AH 28. Route the sensor harness along the vehicle harness AH 16 / 36

17 29. Connect the sky blue wire in the sensor harness with the sky blue wire in the vehicle 20-pin connector using the joint connector case and cover. For connection of joint connector case and cover, refer to How To Install The Joint Connector Case and Cover. 30. Secure the sensor harness sky blue wire to the vehicle harness using an insulating tape. SKY BLUE WIRE 20-PIN CONNECTOR SIDE VIEW JOINT CONNECTOR CASE AND COVER SKY BLUE WIRE INSULATING TAPE 20-PIN CONNECTOR AH 31. Secure the sensor harness to the vehicle harness using four wire ties. 4 WIRE TIES AH 17 / 36

18 32. Secure the sensor harness to the vehicle harness using four wire ties. 4 WIRE TIES AH <With trailer harness> a. Unplug the jumper connector from the sensor harness 2-pin connector. b. Remove the dummy connector from the sensor harness 2-pin connector, and connect the trailer harness 2-pin connector to the sensor harness 2-pin connector. DUMMY CONNECTOR 2-PIN CONNECTOR 2-PIN CONNECTOR (Blue) TRAILER 2-PIN CONNECTOR JUMPER CONNECTOR (Blue) BH <Without vehicle harness> 33. Secure the sensor harness to the vehicle harness using six wire ties. 6 WIRE TIES 7N0602AH 18 / 36

19 <With vehicle harness> a. Secure the sensor harness and the excess vehicle harness to the vehicle harness using three wire ties as shown. b. Secure the sensor harness to the vehicle harness using three wire ties as shown. 6 WIRE TIES Excess vehicle harness CH 34. Install the connector clip to the sensor harness 12-pin connector, and secure the connector clip to the vehicle panel. 12-PIN CONNECTOR CONNECTOR CLIP PANEL AH Installing the Sensor Installation of the Sensor <NORMAL BUMPER> : Go to step 35. Installation of the Sensor <TYPE-S BUMPER> : Go to step 53. Installation of the Sensor <AERO BUMPER> : Go to step 71. <NORMAL BUMPER> 35. Using scissors, cut out the template. TEMPLATE Cut out AH 19 / 36

20 36. Using a felt-tip pen, mark lines in the scribe marks of the rear bumper as shown. REAR BUMPER FELT-TIP PEN Equal distance Equal distance SCRIBE MARK Equal distance 7N0505BH 37. Attach the templates to the rear bumper aligning them with the corresponding lines as shown. 38. Using a pushpin, pierce the rear bumper by piercing at the center of the mark on each template. 39. Remove the templates. LINE TAPE LINE TAPE LINE TEMPLATE TEMPLATE Pierce the center of the mark. Pierce the center of the mark. Pierce the center of the mark. PUSHPIN REAR BUMPER BH 20 / 36

21 40. While wearing eye protection, drill the rear bumper at the four pierced points you just made using a drill with 3 mm bit first, then using a 26 mm hole saw. 41. Remove the burrs from the edge of each hole using a scraper. REAR BUMPER NOTICE Remove the burrs with care not to change the hole diameter. 3 mm DRILL BIT DRILL 26 mm HOLE SAW AH 42. Install the four bumper adaptors to the rear bumper as shown. PROJECTION Install with the projection toward up. 4 BUMPER ADAPTORS REAR BUMPER AH 21 / 36

22 43. Install the four spring housings to the four bumper adaptors as shown. REAR BUMPER 2 TABS SPRING HOUSING Turn. Lock. 4 BUMPER ADAPTORS 4 SPRING HOUSINGS AH 44. Push the two knobs on the spring housing one notch at a time alternately and push them up to four notches on each side, then secure the spring housing. Repeat the procedure on each of the four spring housings. NOTICE Note that pushing the two knobs excessively can break the spring housing. SPRING HOUSING 2 KNOBS Push alternately. 4 NOTCHES BH 22 / 36

23 45. Open the box. Push the heads of the sensors perpendicularly to the box and remove the sensors from the box. BOX Open. NOTICE Never remove the sensors WRONG way. Push perpendicularly. Do not hold here. BOX CORRECT WRONG AH 46. Install the ring on each of the four sensors. RING AH 47. Install the four sensors to the four spring housings as shown. 4 S 4 SPRING HOUSINGS AH 23 / 36

24 48. Plug the four sub harness 3-pin connectors to the four sensors. 4 S 4 SUB 3-PIN CONNECTORS AH 49. Align the three green-taped parts on the sub harness with the three sensors as shown, and secure the sub harness to the three sensors using three wire ties. 3 WIRE TIES 3 S SUB 3 GREEN TAPES BH 50. Using contact cleaner on a shop towel, clean the area where the harness tape will attach. 51. Attach the sub harness with six harness tapes to the rear bumper. SUB REAR BUMPER 6 TAPES AH 24 / 36

25 52. Bring the rear bumper close to the vehicle. Plug the sub harness 12-pin connector into the sensor harness 12-pin connector, and install the rear bumper in the original position. Have an assistant help you when removing and installing the rear bumper. Install the clips securely so that they are not raised. Go to Check After Installation. 12-PIN CONNECTOR SUB 12-PIN CONNECTOR REAR BUMPER AH <TYPE-S BUMPER> 53. Using scissors, cut out the template. TEMPLATE Cut out AH 54. Using a felt-tip pen, mark lines in the scribe marks of the rear bumper as shown. REAR BUMPER FELT-TIP PEN Equal distance Equal distance SCRIBE MARK Equal distance 7N0506BH 25 / 36

26 55. Attach the templates to the rear bumper aligning them with the corresponding lines as shown. 56. Using a pushpin, pierce the rear bumper by piercing at the center of the mark on each template. 57. Remove the templates. LINE TAPE LINE TAPE LINE Pierce the center of the mark. TEMPLATE Pierce the center of the mark. TEMPLATE Pierce the center of the mark. PUSHPIN REAR BUMPER BH 58. While wearing eye protection, drill the rear bumper at the four pierced points you just made using a drill with 3 mm bit first, then using a 26 mm hole saw. 59. Remove the burrs from the edge of each hole using a scraper. REAR BUMPER NOTICE Remove the burrs with care not to change the hole diameter. 3 mm DRILL BIT DRILL 26 mm HOLE SAW AH 26 / 36

27 60. Install the four bumper adaptors to the rear bumper as shown. PROJECTION Install with the projection toward up. 4 BUMPER ADAPTORS REAR BUMPER AH 61. Install the four spring housings to the four bumper adaptors as shown. REAR BUMPER 2 TABS SPRING HOUSING Turn. Lock. 4 BUMPER ADAPTORS 4 SPRING HOUSINGS AH 27 / 36

28 62. Push the two knobs on the spring housing one notch at a time alternately and push them up to four notches on each side, then secure the spring housing. Repeat the procedure on each of the four spring housings. NOTICE Note that pushing the two knobs excessively can break the spring housing. SPRING HOUSING 2 KNOBS Push alternately. 4 NOTCHES BH 63. Open the box. Push the heads of the sensors perpendicularly to the box and remove the sensors from the box. BOX Open. NOTICE Never remove the sensors WRONG way. Push perpendicularly. Do not hold here. BOX CORRECT WRONG AH 64. Install the ring on each of the four sensors. RING AH 28 / 36

29 65. Install the four sensors to the four spring housings as shown. 4 S 4 SPRING HOUSINGS AH 66. Plug the four sub harness 3-pin connectors to the four sensors. 4 S 4 SUB 3-PIN CONNECTORS AH 67. Align the three green-taped parts on the sub harness with the three sensors as shown, and secure the sub harness to the three sensors using three wire ties. 3 WIRE TIES 3 S SUB 3 GREEN TAPES BH 29 / 36

30 68. Using contact cleaner on a shop towel, clean the area where the harness tape will attach. 69. Attach the sub harness with six harness tapes to the rear bumper. SUB REAR BUMPER 6 TAPES AH 70. Bring the rear bumper close to the vehicle. Plug the sub harness 12-pin connector into the sensor harness 12-pin connector, and install the rear bumper in the original position. Have an assistant help you when removing and installing the rear bumper. Install the clips securely so that they are not raised. Go to Check After Installation. 12-PIN CONNECTOR SUB 12-PIN CONNECTOR REAR BUMPER AH 30 / 36

31 <AERO BUMPER> 71. Using a pushpin, pierce the rear bumper by piercing at the center of the four scribe marks on the rear bumper. There are several markings on the inner side of the rear bumper, make certain that you locate the proper cross marks. Pierce the center of the mark. SCRIBE MARK Use C. Pierce the center of the mark. PUSHPIN REAR BUMPER Pierce the center of the mark. SCRIBE MARK Use C. Pierce the center of the mark CH 72. While wearing eye protection, drill the rear bumper at the four pierced points you just made using a drill with 3 mm bit first, then using a 26 mm hole saw. 73. Remove the burrs from the edge of each hole using a scraper. REAR BUMPER NOTICE Remove the burrs with care not to change the hole diameter. 3 mm DRILL BIT DRILL 26 mm HOLE SAW AH 31 / 36

32 74. Install the two bumper adaptors A and the two bumper adaptors B to the rear bumper as shown. SIDE VIEW PROJECTION Install with the projection toward up. Upper and lower sides are the same width. 2 BUMPER ADAPTORS A REAR BUMPER Upper side is wider. PROJECTION SIDE VIEW 2 BUMPER ADAPTORS B Install with the projection toward bottom BH 75. Install the four spring housings to the four bumper adaptors as shown. REAR BUMPER 2 TABS SPRING HOUSING Turn. Lock. 4 BUMPER ADAPTORS 4 SPRING HOUSINGS AH 32 / 36

33 76. Push the two knobs on the spring housing one notch at a time alternately and push them up to four notches on each side, then secure the spring housing. Repeat the procedure on each of the four spring housings. NOTICE Note that pushing the two knobs excessively can break the spring housing. SPRING HOUSING 2 KNOBS Push alternately. 4 NOTCHES BH 77. Open the box. Push the heads of the sensors perpendicularly to the box and remove the sensors from the box. BOX Open. NOTICE Never remove the sensors WRONG way. Push perpendicularly. Do not hold here. BOX CORRECT WRONG AH 78. Install the ring on each of the four sensors. RING AH 33 / 36

34 79. Install the four sensors to the four spring housings as shown. 4 S 4 SPRING HOUSINGS AH 80. Plug the four sub harness 3-pin connectors to the four sensors. 4 S 4 SUB 3-PIN CONNECTORS AH 81. Align the three green-taped parts on the sub harness with the three sensors as shown, and secure the sub harness to the three sensors using three wire ties. 3 WIRE TIES 3 S SUB 3 GREEN TAPES BH 34 / 36

35 82. Using contact cleaner on a shop towel, clean the area where the harness tape will attach. 83. Attach the sub harness with six harness tapes to the rear bumper. SUB REAR BUMPER 6 TAPES AH 84. Bring the rear bumper close to the vehicle. Plug the sub harness 12-pin connector into the sensor harness 12-pin connector, and install the rear bumper in the original position. Have an assistant help you when removing and installing the rear bumper. Install the clips securely so that they are not raised. 12-PIN CONNECTOR SUB 12-PIN CONNECTOR REAR BUMPER AH Check After Installation Check that all wire harnesses are routed properly and all connectors are plugged in. Reinstall all removed parts. Connect the negative cable to the battery and check operation of all lights and other electrical accessories. Enter the customer s radio anti-theft code, and reset the radio station presets. Reset the clock. Do the Accelerator Pedal Kickdown Click System Learn Procedure described in the Shop Manual. Check that the parking sensor system works properly as described in the owner s manual. 35 / 36

36 Sequence for Self-Diagnostic and Loudness Setting The control unit is factory-set to maximum in loudness. Perform Loudness Setting when your customer requests less loudness. Ignition off. Connect diagnostic signal to GND. Ignition on. Self-Diagnostic is running. (See steps 0 through 7 below.) Ignition off. Disconnect diagnostic signal from GND. System is in operating mode. Loudness Setting Engage reverse gear. Disconnect diagnostic signal from GND. Loudness setting is running; tone with duty cycles with loudness changes. Connect diagnostic signal to GND. (The current loudness is set after disconnect of the diagnostic signal and an ignition cycle.) Sensor 8 Sensor 9 Sensor 10 Sensor 11 Self-Diagnostic AH Step Error type Tone freq. [Hz] Acoustical display 0 Initialization of rear system 600 Tone (2 s) + Pause (1 s) Failure display starts 1 ECU failure 600 = error Tone (1 s) + Pause (0.5 s) 1000 = no error 2 Power supply / Sensor supply 600 = error Tone (1 s) + Pause (0.5 s) WD supply failure 1000 = no error 3 Sensor 8 failure 600 = error Tone (1 s) + Pause (0.5 s) (rear right outer) 1000 = no error 4 Sensor 9 failure 600 = error Tone (1 s) + Pause (0.5 s) (rear right inner) 1000 = no error 5 Sensor 10 failure 600 = error Tone (1 s) + Pause (0.5 s) (rear left inner) 1000 = no error 6 Sensor 11 failure 600 = error Tone (1 s)+ Pause (0.5 s) (rear left outer) 1000 = no error 7 End of the diagnosis rear No tone Pause (2 s) 36 / 36