PRELIMINARY QUOTATION No for the supply of. No.1 LEVELLING MACHINE
|
|
- Roger Clark
- 7 years ago
- Views:
Transcription
1 Preliminary quotation No pag. 1 PRELIMINARY QUOTATION No for the supply of No.1
2 Preliminary quotation No pag. 2 Preliminary quotation No ============================ A - GENERAL SPECIFICATION A1 TECHNICAL FEATURES OF WORKING MATERIAL MATERIAL Hot and cold rolled steel strip, galvanized strip, stainless steel strip, aluminum strip. - Tensile strength N/mm ² max Yield strength N/mm ² max Elongation % min. max. 20 STRIP - Strip thickness mm min. 1,5 max. 5,0 - Strip width mm min. 200 max A2 GENERAL FEATURES OF THE LINE - Line speed max. m/min. to be defined - Work direction right to left or left to right - Pass line height mm 1400 A3 - POWER SUPPLY PROVIDED BY BUYER ELECTRICAL VOLTAGE - 3-phase voltage 400 V 50 Hz (to be confirmed) - Auxiliary voltage 230 V 50 Hz (to be confirmed) - Signal voltage for PLC 24 V D.C. (to be confirmed) - Voltage of electro-valves 24 V D.C. (to be confirmed) HYDRAULIC POWER PACK - Working pressure (nominal) 120 bar (to be confirmed) PNEUMATIC FEATURES - Normal compressed air pressure: Mpa.
3 Preliminary quotation No pag. 3 A4 NOISE LEVEL Our equipment is studied and technical solution are adopted to comply as much as possible with Directive 2006/42/EC. During material processing (cutting and stacking), the noise level can be over 85 dba depending on the ambient, type of steel, thickness, line speed, cuts number, building where the line is placed. If local, regional, State Laws and Regulations indicate a max level of noise, any intervention and/or device keeping the noise at the requested level should be discussed after line installation and commissioning. If expressly requested appropriate measurements will be taken to record the real values of noise level along the line which are mostly depending on the ambient where the line is installed. FIMI as supplier is not aware of local, regional, State Laws and regulations and the present quotation does not include measurements and provision of sound-proof cabinets or devices. A5 ENVIRONMENTAL PROTECTION This quotation does not include any, study, measurement and equipment to comply with any eventual local, regional, State Laws, Rules and Regulations on type and max level of environmental pollution. A6 CE DECLARATION This quotation has to be intended as supply of single machines, which do not modify the performances of the original line but are an improvement of the quality, which can be achieved by the same line. In fact, the insertion of these machines doesn t modify neither the operating mode nor the performances of the original line. FIMI does not assume responsibilities or engagement on the operation of the other machines composing the line and on the technical performances of the whole line. For this supply, FIMI will issue certification according to ANNEX II B of Directive 2006/42/EC.
4 Preliminary quotation No pag. 4 Preliminary quotation No ============================ B SCOPE OF SUPPLY B01) No.1 NEW The Levelling machine is in charge to flatten the strip. Nominal load : 400 ton. Six-high cassette type, working rolls, intermediate & back-up rolls. Nr. 1 roller cassette. - Nr. 17 working rolls Ø 63 mm, leveling of strip in the thickness range 1,5 to 5,0 mm. Lower and upper back-up rolls series: 5 series. 17 drive spindles. - Motorized localized correction of lower back-up rolls. - Upper bridge positioning by means of AC motors. - Hydraulic locking device of roller cassette for quick change-over. - Distributor gear. Lubrication : - Working rolls: centralized grease lubrication by means of a motor pump. - Distributor lubrication, oil bath. - Drive spindles: oil drop lubrication by means of a motor pump. TOTAL EXTRACTION OF ROLLER CASSETTE MANUAL EXTRACTION It consists of a facility to take out/in the complete cassette i.e. upper and lower levelling rolls, intermediate & back-up rolls, drive spindles. Roller cassette changing time : the time needed to carry out the changing of the cassette as take out of the cassette and put in of a new one is 15 minutes about. Remark: Changing time of the roller cassette estimated without considering time spent to carry out unloading/loading of roller cassette by using the crane (Buyer supply) available in the area of the Levelling machine.
5 Preliminary quotation No pag. 5 B02) HYDRAULIC, PNEUMATIC & LUBRICATION EQUIPMENT ON BOARD MACHINE, FIMI standard. - Installation on board up to machine bottom and relevant materials - Hydraulic and pneumatic electro-valves are grouped onto single stands mounted to the floor near the machine. - A tray is fitted underneath each hydraulic manifold to collect accidental oil leakage. Buyer supply: Hydraulic power pack. FIMI machine need working pressure nominal 120 bar and flow l/min. about. B03) ELECTRICAL & ELECTRONIC EQUIPMENT FIMI standard. - Machine provided with its own electrical devices and motors mounted on board. (main electric motor not included). - Interface with existing line equipment not included in FIMI supply. B04) DOCUMENTATION as attached list (D2) B05) DELIVERY EXW Fimi (IT), good unpacked, according to Incoterms 2010, C.C.I. Paris. B06) SAFETY PROTECTION AROUND THE MACHINE Buyer supply.
6 Preliminary quotation No pag. 6 C EXCLUSIONS THIS QUOTATION DOES NOT INCLUDE - Dismounting of the existing machines. - Any kind of mechanical, hydraulic & electrical interface with the existing machines. - Safety protection around the machine. - Sound-proof cabinets and devices for the line or single machine according to local, regional, State Laws and Regulations - Environmental safety devices according to local, regional, State Laws and Regulations. - Civil works - Foundations - Foundation plates with foundation plates supports, underground passages coverings - Coverings in-between the machines and profile of foundation; coverings to be shaped at site according to profile of foundation - Galleries and service boards - Bridge crane for erection at site (Buyer s supply) - Compressor for compressed air - Oil and grease for first filling - Hydraulic power pack. - HVAC. - Grounding system - Lights and sockets - Communication and telephone system - Video and cameras system - Electric power supply with distribution transformers, protections and power centers - Spare parts. - Wearing parts. - Material for line test i.e. coils and packaging materials. - Development software of the PLC (Programmable Logic Controller) - Development software of HMI (Human Machine Interface) - Any taxes and/or import duties - Transport and insurance. - Mechanic, hydraulic, pneumatic and electrical installation and start-up at site. - Installation material - Everything, which is not stated in the present offer.
7 Preliminary quotation No pag. 7 D1 FIMI STANDARD - VENDOR LIST All the hydraulic, pneumatic and electric components are dimensioned in accordance to FIMI standards and European and/or international norms and regulations UNI, CEI, EN, ISO, IEC, DIN, SAE. All the Suppliers are selected from a list of primary European manufactures pre qualified by FIMI after testing of their equipment in our workshop and compliance with FIMI required performances. FIMI reserve the right to choose one of the Suppliers depending on required technical specifications, delivery time, and specific conditions. In the case Customer/Buyer imposes a specific supplier and/or different standards, FIMI reserves the right to apply an additional cost to be calculated in accordance. FIMI Vendor list will be delivered to the customer during the design phase together with standard documentation. D2 FIMI STANDARD DOCUMENTATION DOCUMENT Language CD copies During Basic Design stage: Pass-line drawing 1 Lay-out drawing 1 English Guideline foundation drawings with lists of the 1 embedded materials Before delivery: Quotation of recommended wearing and spare parts English 1 After machines supply: Handling instructions 1 General Safety Specification 1 Maintenance manuals 1 Assembly drawing of each machine 1 English Hydraulic, pneumatic and lubrication schemes 1 with relevant component lists Electric drawings 1 Control desk and electric cubicles lay-out 1 REMARKS: - Some detail drawings will be supplied on request of Buyer free of charge for the scope of direct manufacturing of some part damaged. - As built and final technical documentation, both mechanical and electrical, will be delivered 60 days after the date of Final Acceptance Test.
8 Preliminary quotation No pag. 8 E TERMS OF SALE E1 PRICE Pos. Description Price (EUR) B01 B E2 DELIVERY TIME Order starting date : date of downpayment Delivery EXW : to be stated End of erection : Line take-over (full production) Final Acceptance Test E3 TERMS OF PAYMENT - 30 % at the order as down-payment - 30 % at half delivery - 35 % at delivery EXW - 5 % at Final Acceptance Test. E4 WARRANTY The goods are covered from a guarantee for 12 months starting from line take-over. The warranty covers the defective pieces and the replacing time but not the travel costs and travel time E5 OFFER VALIDITY 30 days. BEST REGARDS F.I.M.I. S.p.A. Giuseppe Rovelli Sales Manager Franz Wurzel General Manager
9
HJK CONSULTING ENGINEERS. Project Management Technology Operating Consulting Excellence
HJK CONSULTING ENGINEERS Project Management Technology Operating Consulting Excellence COLD ROLLING MILL EQUIPMENT HJK Consulting Engineers is supporting its client in sales of the following southern Europe
More informationOffer No: 156/2010. Date: December 17, 2010. Dear gentlemen,
CONSTRUCTION MACHINES PRODUCTION PAGE 1 PROMETAL S.R. Milosava Vlajića 49 11450 Sopot Serbia EUROPE Tel. +381.63.133.44.56 +381.63.8623.758 Fax +381.11.283.41.39 web site: bank: Raiffeisen Bank Serbia
More informationSingle sub-base valve
solenoid valves Mini-valves 10 mm Electrical connection... Mounting... Port sizes... Rated temperature... Fluid... Working pressure... Nominal flow... Pneumatic connections Voltage... Power... NC poppet
More informationOffer No: 52/2011. Date: August 9, 2011. Dear gentlemen,
CONSTRUCTION MACHINES PRODUCTION PAGE 1 PROMETAL S.R. Milosava Vlajića 49 11450 Sopot Serbia EUROPE Tel. +381.63.133.44.56 +381.63.8623.758 Fax +381.11.283.41.39 web site: bank: Raiffeisen Bank Serbia
More information1.1 DIMENSIONS AND WEIGHT PAG. 2 1.2 LOAD CENTRE FOR LIFTING PAG. 2 1.3 STORAGE CONDITIONS PAG. 2
TRANSPORT AND INSTALLATION. DIMENSIONS AND WEIGHT PAG.. LOAD CENTRE FOR LIFTING PAG..3 STORAGE CONDITIONS PAG. STARTING. INSTALLATION PAG.. SPACE REQUIREMENTS PAG. 3.3 ELECTRIC CONNECTION PAG. 3 3 DESCRIPTION
More information1x90 TONS TENSIONERS TECHNICAL PROPOSAL. 1 X 90 Tons 30 m/min Tensioners TECHNICAL PROPOSAL JOB 08/059. 0 19/02/2008 Basic proposal PP GM SB
Pagina N.: 1 of 19 1 X 90 Tons 30 m/min Tensioners JOB 08/059 0 19/02/2008 Basic proposal PP GM SB Rev N Date Issue Description Prepared by Checked by Approved by Pagina N.: 2 of 19 TABLE OF CONTENTS:
More informationNAGEL ECO 180 FLEXIBLE HONING SYSTEM
NAGEL ECO 180 FLEXIBLE HONING SYSTEM NEW DEVELOPMENT For Small and Medium Production Runs In-process gauging, Roughing and finishing in a single spindle Tel: 734-426-1812 www.nagelusa.com MACHINE HIGHLIGHTS
More informationDirectional seated valves type VP 1
Directional seated valves type VP 1 zero leakage, intended for general hydraulic applications and grease lubing systems Flow Q max Operation pressure p max = 15 lpm = 400 bar Individual valve Individual
More informationEquipment Information
3002A Equipment Information INDEX: DESCRIPTION AND KEY FEATURES LAYOUT NOMINAL TECHNICAL DATA CONFIGURATION Sealed Air GmbH Customer Systems Center D4 Park 4 CH-6039 Root-Längenbold Telephone: +41 (0)
More informationCOOLSIDE box R410A. conditioned server - racks for direct installation into the room INVERTER E C
COOLS conditioned server - racks for direct installation into the room COOLSIDE box INVERTER R410A E C 2 COOLSIDE box GENERAL FEATURES COOLSIDE BOX is a split system consisting of an outdoor motocondensing
More informationTELESCOPE Motorized Lighting Suspension
TELESCOPE Motorized Lighting Suspension Mod. 8400 FEATURES The De Sisti TELESCOPE is a single point suspension specifically designed to provide rigidity and stabilization of all moving parts. It can extend
More informationMANTA Piston Distributor for Oil and Fluid Grease
MANTA Piston Distributor for Oil and Fluid Grease Function Piston distributors meter out and distribute the oil delivered by an intermittently actuated pump. The quantities of oil for the individual lube
More informationQPM3 Low pressure pump for circulation of oil in hydraulic and lubricating systems
The Professional Choice in Fluid Management QPM3 Low pressure pump for circulation of oil in hydraulic and lubricating systems The Olaer Group is a global player specialising in innovative, efficient system
More informationOperating Instructions Drill rig DRU160
Operating Instructions Drill rig DRU160 Index 000 / 001 Original operating instructions 10988825 en / 20.10.2009 Congratulations! With a Hydrostress unit from TYROLIT you have chosen a tried and tested
More informationValve series MN-06 acc. to NAMUR, 3/2-way G1/4 750 Nl/min (0.762 Cv)
Valve series MN-06 acc. to NAMUR, 3/2-way G1/4 750 Nl/min (0.762 Cv) Order code Series and function 1) Plug socket see page 5.042. MN-06-310-HN-442 Standard coil 1) 441 = 12 V DC, 4.2 W 442 = 24 V DC,
More informationEnglish AUTOMATION SYSTEMS FOR SLIDING GATES. Operating and installation instructions SLIDE SERIES
English AUTOMATION SYSTEMS FOR SLIDING GATES Operating and installation instructions SLIDE SERIES v.0 Rev /202 INDEX ) General Safety Regulations... pág. 0 2) Description... pág. 02 3) Technical Specifications...
More information[ means: Save time, money and space! MAXXMILL 500. Vertical milling center for 5-side machining
[ E[M]CONOMY] means: Save time, money and space! MAXXMILL 500 Vertical milling center for 5-side machining MAXXMILL 500 MAXXMILL 500 is the ideal vertical milling center for the for the 5-axis operation
More informationSOLENOID VALVES AND PNEUMATIC VALVES
2 A S E R I E S Catalogue 2005-2006 Directly operated solenoid valves Series A 2/2 way, 3/2 way monostable, bistable (with magnetic memory) Ports M5,, cartridge ø4 The Series A solenoid valves are of the
More informationECOCIAT. Domestic hot water heat recovery unit
Heat recovery unit Domestic hot water High energy efficiency with R410A Compact and quiet Scroll compressors Brazed-plate heat exchangers Heating Heat recovery ENVIRONMENTALLY HFC R410A PROTECTION DE FRIENDLY
More information3.1.1 Full Type Tests & Routine Tests according to Clause 8 2 & 8 3. 4.0 Instructions For Installation, Operation & Maintenance
SPECIFICATION FOR LOW VOLTAGE SWITCHBOARD SEN I N D E X Description 10 STANDARD TECHNICAL REQUIREMENTS 11 Standards 12 General Operating Conditions 13 General Description Of Switchboard 131 Structure 132
More informationAssisted lift operated 2/2-way solenoid valves Type EV250B
MAKING MODERN LIVING POSSIBLE Data sheet Assisted lift operated 2/2-way solenoid valves Type EV250B EV250B with assisted lift can operate from zero and up to 10 bar differential pressure. This 2/2-way
More informationOperating Manual UWAPS-TINY Series
Operating Manual UWAPS-TINY Series Powecon Oy WWW.POWECON.FI 1/9 Table of content 1 Warranty...3 2 Safety information...3 3 Abbreviations and terminology...3 4 List of appendices...4 5 Introduction...4
More informationProcurement Specification for a High Security Lift Arm Barrier (HSLAB) EB950 CR Armstrong High Security Lift Arm Barrier
Procurement Specification for a High Security Lift Arm Barrier (HSLAB) EB950 CR Armstrong High Security Lift Arm Barrier A. Requirement This document is to be used to specify the physical and operational
More informationTitan Makina Ltd. Şti. 1160. Sok. No: 9 Ostim 06370 Ankara Tel: + 90 312 354 9977 Fax: + 90 312 385 5611 Web: www.titanltd.com.
IS26 Concrete Spraying Machine IS26 Concrete Spraying Machine TECHNICAL SPECIFICATIONS Manipulator Max. vertical spraying reach : Max. horizontal spraying reach : Working lights : Spraying Head Rotation
More informationIn addition, a number of auxiliary options are available (para 2.7) as well as optional slices for special requirements (para 2.8).
DS3002 1. General Description This data sheet describes the Modular Power (MP) Electro Hydraulic Power Units, which have been designed to provide an advanced and flexible means of brake control. The MP
More informationDEK-REL- 24/1/SEN. Extract from the online catalog. Order No.: 2964050
Extract from the online catalog DEK-REL- 24/1/SEN Order No.: 2964050 Relay terminal block for sensor, with soldered-in miniature relays, contact (AgNi+Au): small to medium loads, 1 N/O contact, input voltage
More informationButterfly Valves PN 6/10/16 for flanged connection
4 136 ACVATIX Butterfly Valves PN 6/10/16 for flanged connection tight-closing VKF46.. VKF46..TS Grey cast iron housing EN-GJL-250 (to DN 300) nodular cast iron housing EN-GJS-400-15 (from DN 350) DN 40
More informationValve systems Base plates, according to standard ISO 5599-1. Brochure
ISO 5599-1 Brochure 2 ISO 5599-1 Single subbase Single subbase, thread connections on the side standard: ISO 5599-1 Frame size: ISO 1 - ISO 4 compressed air connection output: G 1/4 - G 1 Reversed pressure
More informationExample of use: Fuse for a solenoid valve. If the fuse is defective, no information is sent to the electronic component.
Overview Switch and button modules The dimensions of the switch and button modules are adapted to the electronic components in the integral housing. The modules are equipped with the universal clip-on
More information3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics
3/2-, 5/2-5/3-way Solenoid Valves for process pneumatics Type 6518 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 6518/6519 can be combined with... Stard-,
More informationA U T O M O T I V E L I F T S
Q U A L I T Y Y O U E X P E C T AT A P R I C E Y O U W O U L D N T T H E S TA N D A R D I N I N F O R M AT I O N, E Q U I P M E N T A N D D I A G N O S T I C S S Y S T E M S h t t p : / / d i a g n o s
More informationCompensation Unit in X-, Y-, and Z-Direction AGE-S-XYZ 100-200
Translation of the original manual Compensation Unit in X-, Y-, and Z-Direction AGE-S-XYZ 100-200 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains
More information3-Way heavy duty flow control, with pressure compensated and solenoid controlled priority flow
1/6 RE 18309-3/06.10 Replaces: RE 18309-3/04.10 3-Way heavy duty flow control, with pressure compensated and solenoid controlled priority flow A-VRFC3C-VEI-VS 0M.43.20.80 - Y - Z Description The flow control
More informationCONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version)
TECHNICAL DATASHEET #TD1102AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version) Part Number: Connector Amplifier CAPV-H-4-20MA-x complete with cable CAPV-4C-yM Where: x = current output
More informationElectro-pneumatic control valves
Electropneumatic control valves 7 Miniature solenoid valves for alternating current Conform to the Low Voltage Directive or mounting on subbase or footprint in accordance with CNOMO recoendation E 066120N
More informationCentro-Matic Automatic Lubrication Systems System Controls
Selecting the right controls for your automated lubrication system is one of the last steps in the design process. Several different models may be chosen to control power-operated pumps, depending on the
More informationRefrigeration Compressed Air Dryer Buran Ultrapulse
Refrigeration Compressed Air Dryer Buran Ultrapulse There is more to compressed air than just compressing air Compressed air is an indispensable source of operating and processing power in all areas of
More informationUSE AND MAINTENANCE MANUAL
FORKS POSITIONER Mod. FR-FP-FFP ORIGINAL INSTRUCTIONS INTRODUCTION This manual includes instructions for assembly, maintenance (regular and extraordinary), and for possible faults with remedies. The instructions
More informationHERZ-Thermal Actuators
HERZ-Thermal Actuators Data Sheet 7708-7990, Issue 1011 Dimensions in mm 1 7710 00 1 7710 01 1 7711 18 1 7710 80 1 7710 81 1 7711 80 1 7711 81 1 7990 00 1 7980 00 1 7708 11 1 7708 10 1 7708 23 1 7709 01
More informationH45 LED - Direct and indirect pendant
RAL 01 10 00 IP 20 230V 50/60Hz Specifications Direct and indirect light pendant linear luminaire. Aluminium profile. Diffusers in frosted polycarbonate profile. Driver included. Supplied with clear base,
More informationElectrically operated valves Series M-05, 3/2-, 5/2- and 5/3-way G1/8 650 and 750 Nl/min (0.661 and 0.762 Cv)
Electrically operated valves Series M-05, 3/2-, 5/2- and 5/3-way G1/8 650 and 750 Nl/min (0.661 and 0.762 Cv) Order code Series and function M-05-310-HN-442 Standard coil HN at ports 2 + 4 HN at ports
More informationI E D C E R T. Net MA N A G E ME N T S Y S T E M ISO 9001: 2000 9105.RAVI. Pendant Stations LADY Series
C E R T I F MA N A G E ME N T I E D Net ISO 9001: 2000 9105.RAVI I S Y S T E M Pendant Stations LADY Series 4.1 Pendant Stations LADY Series - LA type single-row Main Features The new LADY series single-row
More informationair water oil antifreeze grease diesel fuel kerosene oxygen-acetylene lpg-methane electricity Hose & cable reel
air water oil antifreeze grease diesel fuel kerosene oxygen-acetylene lpg-methane electricity Hose & cable reel Catalogue 2008 Table of contents Series standard hose reels in painted steel page 5-6 For
More informationOPERATOR s MANUAL ROLL AND EXTENSION TABLES
OPERATOR s MANUAL ROLL AND EXTENSION TABLES 1 INDEX Page Manufacturer s Information 3 Warnings 4 Risks and Labelling 5 Safety Precautions 6 Warranty 7 Dimensions and Weight 8 Shipping Dimensions 8 Transport
More information225-230T-05-S2. Rotary drive without spring return. Technical data sheet. Description. Technical data. Actuators
Actuators Technical data sheet 225-230T-05-S2 Rotary drive without spring return Description Actuator for adjusting air dampers of 90 angle of rotation to be used in HVAC installations. Torque Motor 5
More informationScrew Compressors ESM 30 132 Fixed Speed & VS 30 132 Variable Speed
Screw Compressors ESM 30 132 Fixed Speed & VS 30 132 Variable Speed Rely on GD to provide the perfect fit The perfect fit to maximise productivity The growing industrial demand for compressed air requires
More informationEnduraLAM 150 User Manual
EnduraLAM 150 User Manual SIGNWarehouse, Inc. 2614 Texoma Drive Denison, Texas 75020 800-699-5512 Website: www.signwarehouse.com Email: TechSupport@signwarehouse.com Copyright 2014 SIGNWarehouse, Inc.
More informationCold Room & Refrigeration System (Casserole Assembly) No of units: 1
Technical Specifications Cold Room & Refrigeration System (Casserole Assembly) No of units: 1 For chiller storage of all sorts of items Chiller storage temperature: 2-5 C Provides excellent thermal efficiency
More informationE08 E10. Compact Excavators
E08 E10 Compact Excavators E08 Micro-Excavator Retractable undercarriage and blade Foldable TOPS structure Built-in operator safety Compact dimensions Cylinder-over-the-boom design Optional Demolition
More information2-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow
2-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow RE 18309-64/04.10 1/6 Replaces: RE 00171/02.07 A-VRFC2C-VEI-VS-LS 0M.28.03.80 - Y - Z Description
More informationArt.S001-S002 SOLAR MODULE WITH DELIVERY AND RETURN CONNECTIONS
Art.S001-S002 SOLAR MODULE WITH DELIVERY AND RETURN CONNECTIONS Technical Information sheet 0001/07/Rev01 ENG FUNCTION Series S001 and S002 circulation units are applied to the primary circuit of solar
More informationJIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes 1. Scope This Japanese Industrial Standard specifies the electric resistance welded carbon steel tubes, hereinafter
More informationHIGH PRESSURE TECHNOLOGY HYDRAULICS PNEUMATICS TESTING EQUIPMENT
HIGH PRESSURE TECHNOLOGY HYDRAULICS PNEUMATICS TESTING EQUIPMENT MAXIMATOR GmbH 2 MAXIMATOR has an extensive know-how concerning concept, development, construction and manufacturing of test benches and
More informationINDUSTRIAL DIRECT DRIVEN PISTON COMPRESSORS CL - CH - CK
INDUSTRIAL DIRECT DRIVEN PISTON COMPRESSORS CL - CH - CK CL - CH - CK Direct driven solution for industry Proven technology, solid construction The CL - CH - CK units are directly driven air-cooled, single
More informationPos. Qty. Article Description Price / Drilling capacity in steel 60 Ø 25 mm Tapping capacity M 20 Milling capacity in steel 60 150 cm³/min.
Offer 1 1 Vertical CNC-machining centre model FZ 12 W Magnum Completely refurbished pre-owned machine Updated in 2015 Year of construction: depends, weight 4.000 kg Scope of delivery: Column moving machining
More informationRotary screw compressors kw 5,5 7,5 11 15 18,5 22 30 bar 8 10 13 15 MODULO
Rotary screw compressors kw 5,5 7,5 11 15 18,5 22 30 bar 8 10 13 15 MODULO The sum of technology TriAB Air ends The BALMA screw compressors are fitted with the unique TriAB air ends that are designed and
More informationInstructions and precautions. Fork Height. Visit our website at: http://www.harborfreight.com
Pallet Jack Item 68760 / 68761 Instructions and precautions Specifications Capacity Control Lever Fork Height Fork Length Fork Width Maximum Minimum Width over Forks Steering Wheel Dia. 2-1/2 Ton (5,000
More informationHigh Security Heavy Duty Shredders VZ 14.00. Perfect shredding and high performance in DIN security levels 4 and 5
High Security Heavy Duty Shredders Perfect shredding and high performance in DIN security levels 4 and 5 Documentation High Security Heavy Duty Shredders / Page 1of 5 Perfect shredding and high performance.
More informationTECHNICAL SPECIFICATION FOR PROJECTION WELDING MACHINE (Qty. 2 Nos.)
TECHNICAL SPECIFICATION FOR PROJECTION WELDING MACHINE (Qty. 2 Nos.) 1. Requirement: Two (02) Nos. DC Type, 3 phase, 3 wire Projection Welding Machine is required for welding of ventilation M.S. / Stainless
More informationElectric Powered Forklift 1.5-2.0 ton
Electric Powered Forklift 1.5-2.0 ton E4 C4E150 C4E160-180 C4E160L-180L C4E200 www.bt-forklifts.com Electric Powered Forklift 1.5 ton Truck specifications C4E150 1.1 Manufacturer BT 1.2 Model C4E150 1.3
More informationFOK MACHINES FIBER OPTIC CABLE BLOWING MACHINES. https://www.fokmachine.com FIBER OPTIC CABLE BLOWING MACHINES
FOK MACHINES fokmachine.com ABOUT US Our company ever since its incorporation in the telecommunication sector has been operating the machine. Our company since its establishment until the superior service
More informationSWIMMING POOL HEAT PUMP Owners Manual
SWIMMING POOL HEAT PUMP Owners Manual This manual refers to the 17.0kw and 21.0kw models only. The heat pump unit is sold with a 1 year warranty. In addition there is a 2 year parts warranty on the compressor
More informationISORIA. Centered disc butterfly valves with AMRING elastomer liner. 240 PSI: 1½ to8. 150 PSI : 10 to 24
Type series booklet 8448.1/2-EN--US ISORIA Centered disc butterfly valves with AMRING elastomer liner 240 PSI: 1½ to8 150 PSI : 10 to 24 Design in accordance with ISO 10631 Manual, electrical, pneumatical
More informationHP switch LP switch Discharge thermo Comp. Surface thermo
1 Specifications Zubadan Model Name PUHZ-SHW80VHA PUHZ-SHW11VHA PUHZ-SHW11YHA Power supply (phase, cycle, voltage) 1φ, V, Hz 1φ, V, Hz 3φ, 0V, Hz Max. current A 9.5 35.0 13.0 Breaker size A 3 16 Outer
More information2- and 3-port valves with flanged connections, PN 10
4 402 VVF32.. VXF32.. ACVATIX 2 and 3port valves with flanged connections, PN 10 From the largestroke valve line VVF32.. VXF32.. Performance valves for medium temperatures from 10 150 C Valve body of grey
More informationMODEL HSR-007 Direct Drive Rolling Steel
MODEL HSR-007 Direct Drive Rolling Steel 200 Fairview Road, Unit #2, Barrie, Ontario L4N 8Z8 Tel: 866-792-9968 or 705-792-9968 Fax: 705-735-9564 www.tnrdoors.com email: info@tnrdoors.com Model HSR-007
More informationDIN 17172-78 STEEL PIPES FOR PIPE LINES FOR THE TRANSPORT OF COMBUSTIBLE FLUIDS AND GASES
DIN 17172-78 STEEL PIPES FOR PIPE LINES FOR THE TRANSPORT OF COMBUSTIBLE FLUIDS AND GASES For connection with the International Draft Standards 3183 and 3845 published by the International Organization
More information225C-024T-05. Continuous control rotary drive without spring return. Technical data sheet. Description. Technical data. Actuators
Actuators Technical data sheet 225C-024T-05 Continuous control rotary drive without spring return Description Actuator for adjusting air dampers of 90 angle of rotation to be used in HVAC installations.
More informationOIL-FREE ROTARY SCROLL COMPRESSOR. ECOLIFE 1,5 15 kw
OILFREE ROTARY SCROLL COMPRESSOR ECOLIFE 1, 1 kw EN Why The continuous innovation of the compressed air tools and machineries, the evolution of specific productive processes and uses, require exclusively
More informationSystem 8. ü www.nassmagnet.com ( +49 511 6746-0. System 8
System 8 ü www.nassmagnet.com ( +9 11 7-0 System 8 The name System 8 stands for a modular system of solenoid coils, armature systems, solenoid operators and solenoid valves. The diameter of the armatures
More informationProportional pressure regulators VPPE
Proportional pressure regulators VPPE Proportional pressure regulators VPPE Product range overview Function Version Pneumatic connection Proportional pressure regulator Nominal size for pressurisation/
More informationMINIFOK MACHINES MINI FIBER OPTIC CABLE BLOWING MACHINE. fokmachine.com FIBER OPTIC CABLE BLOWING MACHINES
MINIFOK MACHINES MINI FIBER OPTIC CABLE BLOWING MACHINE fokmachine.com FIBER OPTIC CABLE BLOWING MACHINES ABOUT US Our company ever since its incorporation in the telecommunication sector has been operating
More informationRotary actuator for 2 and 3-way (control) ball valves Torque 5 Nm Nominal voltage AC 100... 240 V Control: Open/close or 3-point Auxiliary switch
echnical data sheet Rotary actuator LR-S Rotary actuator for and -way (control) ball valves orque 5 Nm Nominal voltage C... 4 V Control: Open/close or -point uxiliary switch echnical data Electrical data
More informationSTRUCTURAL STEELS. Steel Grades S185 S235JR S235JRG2 S235JO S235J2G3 S235J2G4 S275JR S275JO S275J2G3 S275J2G4 S355JR S355JO S355J2G3 S355J2G4
STRUCTURAL STEELS Steel Grades S185 S235JR S235JRG2 S235JO S235J2G3 S235J2G4 S275JR S275JO S275J2G3 S275J2G4 S355JR S355JO S355J2G3 S355J2G4 S355K2G3 S355K2G4 E295 E335 E360 STRUCTURAL STEELS The unalloyed
More informationEPC 3x-X ERNIPRESS CENTER Hydropneumatic Press with pneumatic control. Operating manual EPC 31-X EPC 33-X EPC 35-X EPC 37-X. 19.03.
EPC 3x-X ERNIPRESS CENTER Hydropneumatic Press with pneumatic control Operating manual EPC 31-X EPC 33-X EPC 35-X EPC 37-X 19.03.2008 / BA_EPC 3x-X Copyright Copyright The technical documentation consists
More informationBrochure 2012-2013.EX
CLIMA CANAL Brochure 2012-2013.EX CLIMA CANAL Complete climate control and high power Heating, cooling, ventilation. Despite it s modest size, clima canal is a powerful heating, cooling and ventilation
More informationSTEP-PS/1AC/12DC/1.5. Extract from the online catalog. Order No.: 2868567. DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase
Extract from the online catalog STEP-PS/1AC/12DC/1.5 Order No.: 2868567 DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase Commercial data EAN 4046356292924 Pack 1 pcs. Customs tariff
More informationOutput torques up to 8000 Nm. General features. Protection. External coating. Working temperature range
Type series booklet 8521.15/2--10 ACTELEC 31 to 800 (BERNARD) 1/4 turn electric actuators (irreversible reducer with multi -turn electric actuator ACTELEC 31: screw -nut kinematics ACTELEC 200 to 800:
More informationFluid. Flu. Fluid Fluid. uid Power d Power P. Fluid Power P. Fluid Power. Fluid Power Power. d Power. Directional Cetop Valves DCV 03.
Catalogue Directional Cetop Valves DCV 03 Power Flu uid Power d Power P wer Power Power Power Power Power d Power Power Power ower Power Power wer Power Power P Power Power Powe d Power Power Power Power
More informationCYMAQ Marking System AS200 + DS7050 N-14
CYMAQ Marking System AS200 + DS7050 N-14 Serial Number: 13716 CYMAQ www.cymaq.com INDEX 1. PRESENTATION AND GENERAL POINTS 1.1. General Points 1.2. Identification plate 2. MACHINE CHARACTERISTICS 2.1.
More informationProduct Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
More informationUnit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 4 DIRECTIONAL CONTROL VALVES The material needed for outcome 2 is very extensive
More information3/2- and 2/2-way cartridge valve type BVE
3/2- and 2/2-way cartridge valve type BVE for any flow direction, zero leakage, all ports pressure resistant Flow Q max = 70 lpm Perm. pressure p max = 400 bar Additional valves with same function: ' Type
More informationPressure Relief Valves SPV, SPVF
Pressure Relief Valves SPV, SPVF Construction of the Pressure Relief Valves SPV, SPVF Symbol Description The direct spring, sliding piston Pressure Relief Valve SPV/SPVF is intended for inline mounting
More informationCompact Air Solutions C Series 2.2 7.5 kw Screw Compressors Want a 5. year warranty? Ask for details!
Compact Air Solutions C Series 2.2 7.5 kw Screw Compressors Want a 5. year warranty? Ask for details! Air. CompressedAir. BogeAir. Now you can! CM compact module 2.2 7.5 kw Effective free air delivery:
More informationRAILWAY CATENARY SYSTEMS. Components and Systems for the Electrification of Railway Lines. ibemo
Connectors, Clamps, Compensating Devices, Insulators and Safety Equipment for Overhead Catenary Lines RAILWAY CATENARY SYSTEMS Components and Systems for the Electrification of Railway Lines. Welcome to
More informationElectric Rotary Actuator - On/Off or programmable control actuator
Electric Rotary Actuator - On/Off or programmable control actuator Direct mounting on quarter-turn valves Manual override standard Corrosion resistant Adjustable limit switches Multi-voltage version Type
More informationSICONT Limit Switches Type 3SE3 upto 500 VAC, 600 VDC, 10A
s SICONT Limit Switches Type 3SE3 upto 500 VAC, 600 VDC, 10A Introduction The technical and descriptive information on the function, construction and selection of the new types of 3SE3 limit switches is
More informationIngersoll-Rand LIFTSTAR. Manriding Winches. Classification and compliance with safety requirements
Classification and compliance with safety requirements Meet the toughest personnel lifting requirements in the offshore industry The LIFTSTAR RLP Manriding winches are designed to the toughest type approval
More informationINNOVATIVE SOLUTION OF DOMESTIC HEATING SPLIT TYPE SPLIT DHW INTEGRATED TYPE MONOBLOC TYPE
INNOVATIVE SOLUTION OF DOMESTIC HEATING SPLIT TYPE SPLIT DHW INTEGRATED TYPE MONOBLOC TYPE Fujitsu General realizes considerable energy saving operations by the Heat pump heating system using the ambient
More informationMEDIUM VOLTAGE CE-BF SWITCHBOARDS. UP TO 40.5 kv. CE - BF - C - en - REV.00 2012.4
CE - BF - C - en - REV.00 2012.4 APPLICATION CE-BF Switchbords up to 40.5 kv are designed for use in public and industrial distribution system up to 40,5KV for the operation and protection of lines, transformers,
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. 2012NB Description 304mm (12") Automatic Thickness Planer CONCEPTION AND MAIN APPLICATIONS * Compact and light weight (27 Kg./59 lbs) automatic thickness planer for easier
More informationLG Air conditioning Company Multi V Water Ⅱ. Air Conditioning Academy
LG Air conditioning Company Multi V Water Ⅱ Air Conditioning Academy 1.1 What is Multi V Water II? High Performance Prospect rights Water pipe Refrigerant pipe Indoor unit Beautiful Exterior Convenience
More informationQuestionnaire Pure Media Systems
1. PROJECT INFORMATION: Project Name: Client: Contact Person: Telephone / Fax N : Email: 2. BASIC INFORMATION Type of Pure Media System PW / HPW - Generation PW / HPW - Storage & Distribution System Cold
More informationPLM series Permanent load lifting magnets
Lifting gear Load lifting magnets/chain hoists PLM series Permanent load lifting magnets Load-bearing capacity of up to 1 t depending on model despite light weight High standard of safety with simple lever
More informationTARIFF CODE and updates standard
TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of
More informationCooling kw 5.2 6.0 7.1 Heating kw 5.65 6.35 7.75
Specifications COOLING ONLY / HEAT PUMP 005 006 007 Capacity (Eurovent) Cooling kw 5.2 6.0 7.1 Heating kw 5.65 6.35 7.75 Nominal input (Eurovent) Cooling kw 1.89 2.35 2.95 Heating kw 1.97 2.24 2.83 EER
More informationPlease also see 10 golden rules for correct Saniflo installation on www.saniflo.co.uk
1. Description Sanicom is a lifting pump for wastewater used in commercial applications (restaurants, hairdressing salons, the catering industry etc.). The unit operates automatically, has a high performance
More informationFailure to comply with the following cautions and warnings could cause equipment damage and personal injury.
1.0 IMPORTANT RECEIVING INSTRUCTIONS Visually inspect all components for shipping damage. Shipping Damage is not covered by warranty. If shipping damage is found, notify carrier at once. The carrier is
More informationYour Service Partner Avonmouth and Bristol Service Centres
Your Service Partner Avonmouth and Bristol Service Centres The Sulzer Advantage Avonmouth Service Centre Bristol Service Centre Capabilities Manual machining CNC machining Pump services Thermal spray
More information