10Port PoE Switch User Guide

Transcription

1 10Port PoE Switch User Guide FOR PSE1008GS; PSE1008G Version: V1.1 1

2 1. Introduction 1.1 Package Contents The POE Switch *1 User s Manual *1 19 Rack mount Accessory Kit *1 Cord *1 Rubber Feet *4 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.2 Description To fulfill the demand of sufficient PoE power for network applications with Fast Ethernet speed transmission, the PSE1008GS in the IEEE802.3af PoE Fast Ethernet Switch family is an 8-Port 10/100Mbps IEEE802.3af over Ethernet +1 Gigabit Port +1 SFP Port Switch with a total of 130 watts of PoE budget, which is an ideal solution. It comes with a 13-inch metal compact housing, suitable for desktop deployment in SOHO office or department network application. It s easy to connect. With data and power over Ethernet from one unit, the PSE1008GS reduces cabling requirements and eliminates the need for dedicated electrical outlets on the wall, ceiling or any unreachable place. A wire carries both data and power lowering the installation costs, simplifying the installation effort and eliminating the need for electricians or extension cords. Providing 8 PoE interfaces, the PSE1008GS is ideal for small businesses and workgroups requiring to deploy the PoE for the wireless access points, IP-based surveillance camera or IP phones in any places easily, efficiently and cost-effectively. 1.3 Features * Up to 15.4W of on * complies to IEEE 802.3af PoE standard and is backward * Compatible with All IEEE 802.3af or Legacy * Safe: Low Devices Receive Only the They Need * Safe and Reliable to WLAN Access Points * Automatic Detection and Protection of Non standard Ethernet Terminals * Supports 10/100 Base-T applications * Compact Design Fits Easily in WLAN Access * Plug-and-Play no configuration required * Internal power supply * Save up to 83% power with Green Technology 2

3 1.4 Specification Model PSE1008GS PSE1008G Hardware Specification 10/100Mbps Copper Ports 8 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports 1000Mbps Copper Ports 1 10/100/1000Mbps RJ-45 Auto-MDI/MDI-X ports 2 10/100/1000Mbps RJ-45 Auto-MDI/MDI-X ports SFP/mini-GBIC Slots Switch Architecture Switch Fabric Address Table Base-SX/LX, shared with Port-10 - Store-and-Forward 5.6 Gbps / non-blocking 8K entries Share Buffer Data 512Kbytes Maximum Frame Size Flow Control LED Dimension (W x D x H) Weight Requirement Consumption / Dissipation 9K Bytes Back pressure for Half-Duplex IEEE 802.3x Pause Frame for Full-Duplex (Green) PoE In-Use (Orange) 1000M LNK / ACT(Green) 1000M SFP LNK / ACT(Green) 10/100 LNK / ACT(Green) 330 x 180 x 44 mm, 1U height 2 kg 100~240V AC, Hz PSE1008/150;PSE1008T-250 Watts maximum over Ethernet PoE Standard PSE 1008 /IEEE 802.3af 3

4 PoE Output Per Port 54V DC, 350ma. Max Watts PoE Supply Type 1/2(+), 3/6(-), Mode-A, End-Span PoE Budget System: 150W; PoE: Max. 130W Max. number of Class 3 PD 8-Port Standards Conformance Regulation Compliance Standards Compliance FCC Part 15 Class A, CE IEEE 802.3: 10Base-T IEEE 802.3u: 100Base-TX IEEE 802.3z: 1000Base- SX/LX IEEE 802.3ab: 1000Base-T IEEE 802.3x: Flow Control IEEE 802.3ad: Port trunk with LACP IEEE 802.1D: Spanning tree protocol IEEE 802.1w: Rapid spanning tree protocol IEEE 802.1p: Class of service IEEE 802.1Q: VLAN Tagging IEEE 802.1x: Port Authentication Network Control IEEE 802.3af: over Ethernet Environmental Operating Temperature: 0 ~ 50 Degree C Relative Humidity: 20 ~ 95% Storage Temperature: -10 ~ 70 Degree C Relative Humidity: 20 ~ 95% (non-condensing) 4

5 2. Hardware Description This section describes the hardware features and installation of the POE Switch on the desktop or rack mount. 2.1 Switch Front Panel and Rear Panel >>PSE1008GS >>PSE1008G LED Indicators: System LED Color Function Green Light-> Indicate the Switch has power Per 10/100Mbps Port LED Color Function LAN Green Light->Indicate the link through that port is successfully established at 10/100Mbps. Blink->Indicate that the switch is actively sending or receiving data over that port PoE Orange Light->Indicate the port is providing 48~54V DC in-line power 5

6 Per 10/100/1000Mpbs Port LED Color Function GE LAN Green Light->Indicate the link through that port is successfully established at 10/100/1000Mbps. Blink-> Indicate the link through that port is successfully established at 10/100Mbps. LINK Green Light->Indicate the link through that port is successfully. Blink->Indicate that the switch is actively sending or receiving data over that port SFP 1000Mbps Port LED Color Function GE SFP Green Light->Indicate the link through that port is successfully established at 1000Mbps. LINK Green Light->Indicate the link through that port is successfully. Blink->Indicate that the switch is actively sending or receiving data over that port 2.2 Desktop Installation To install the PoE Ethernet Switch on desktop, simply follow the following steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the PoE Ethernet Switch. Step2: Place the PoE Ethernet Switch on desktop near an AC power source. Step3: Keep enough ventilation space between the PoE Ethernet Switch and the surrounding objects. Step4: Connect your PoE Ethernet Switch to IEEE802.3af complied ed Devices (PD) and other network devices. Step5: Supply power to the PoE Ethernet Switch. a. Connect one end of the power cable to the PoE Ethernet Switch b. Connect the power plug of the power cable to a standard wall outlet. When the PoE Ethernet Switch receives power, the power LED should remain solid Green. 2.3 Rack Mounting To install the PoE Ethernet Switch in a 19-inch standard rack, follow the instructions descryibed below. Step1: Place your PoE Ethernet Switch on a hard flat surface, with the front panel positioned towards your front side. Step2: Attach a rack-mount bracket to each side of the PoE Ethernet Switch with supplied screws attached to the package. Step3: Secure the brackets tightly. 6

7 Step4: Follow the same steps to attach the second bracket to the opposite side. Step5: After the brackets are attached to the PoE Ethernet Switch, use suitable screws to securely attach the brackets to the rack. Step6: Proceeds with Step4 and Step5 of session 2.3 Desktop Installation to connect the network cabling and supply power to your PoE Ethernet Switch. 2.4 Product Application >> Gigabit Port connects with Router, 1~8 Port connects with PD; provide power and data to them. The SFP port provides 1000Mbps data to switch >> Gigabit Port connects with Router, 1~8 Port connects with PD; provide power and data to them. The Gigabit port provides 1000Mbps data to switch 7

8 3. over Ethernet Overview 3.1 What is PoE? The PoE is an abbreviation of over Ethernet; the PoE technology means a system to pass electrical power safely, along with data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with category 3 cable for low power levels. is supplied in common mode over two or more of the differential pairs of wires found in the Ethernet cables and comes from a power supply within a PoE-enabled networking device such as an Ethernet switch or can be injected into a cable run with a mid-span power supply. The original IEEE802.3af-2003 PoE standard provides up to 15.4W of DC power (minimum 44VDC and 350Ma) to each device. Only 12.95W is assured to be available at the powered device as some power is dissipated in the cable. The update IEEE802.3at-2009 PoE standard also known as PoE+ or PoE plus provide up to 25.5W of power. The 2009 standard prohibits a powered device from using all four pairs for power. The 802.3af/802.3at defines two types of source equipment: Mid-Span and End-Span. 3.2 Mid-Span Mid-Span device is placed between legacy switch and the powered device. Mid-Span is tap the unused wire pairs 4/5 and 7/8 to carry power; the other four is for data transmit. 3.3 End-Span End-Span device is directly connecting with powered device. End-Span could also tap the wire 1/2 and 3/6 3.4 PoE System Architecture The specification of PoE typically requires two devices: the ed Source Equipment (PSE) and the ed Device (PD). The PSE is either an End-Span or a Min-Span, while the PD is a PoE-enabled terminal, such as IP Phones, Wireless LAN, etc. can be delivered over data pairs or spare pairs of standard CAT-5 cabling. 3.5 ed Source Equipment (PSE) sourcing equipment (PSE) is a device such as a switch that provides(sources)power on the Ethernet cable. The maximum allowed continuous output power per cable in IEEE802.3af is 15.40W. A later specification, IEEE802.3at, offers 25.5W. When the device is a switch, it is commonly called an End-span (although IEEE802.3af refers to it as endpoint). Otherwise, if it s an intermediary device between a non PoE capable switch and a PoE device; it s called a Mid-span. An external PoE injector is a Mid-span device. 8