Pivot Door Instruction Manual

Transcription

1 Pivot Door Instruction Manual Consumer Guarantee - Please make sure the purchaser/end user completes and returns the Guarantee card which is enclosed with this product. Failure to validate the Guarantee will mean only the 1 Year Statutory Guarantee will apply. Component Check List: Supplied No: Description Quantity 1 Wall Profiles 2 2 Pivot Door 1 Fixing Kit: Component Check List IMPORTANT This is an important document as it holds the Consumer Guarantee which needs to be returned, please ensure it is retained by the end user. Please read these instructions carefully prior to attempting installation. Unpack and handle the product with care to avoid damage to the product finish. Check for hidden electrical cables and water pipes prior to commencing any drilling work. Do not plasterboard over the rim of the Tray. Ensure the walls where the Enclosure is to be fitted are vertical. (If the walls are not completely vertical there is 20mm of adjustment in each Wall Profile.) Note: It is recommended that the walls are tiled after the Tray is fitted and grouted before fitting the Enclosure. This will provide maximum adjustment and will aid sealing. No attempt should be made to rework toughened safety glass. Pictures used are for illustration purposes only, product designs may alter slightly as a result of continuing product development. Roman s toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to our guidelines. It is important to note, that the glass must not be mounted or pinched in such a way that would cause a stress point to develop in the glass. In addition, it must not be subjected to any sharp impact or severe temperature fluctuation which may also cause a stress point to develop in the glass. Roman s toughened glass is physically and thermally significantly stronger than standard glass. During our toughening process the stresses contained within any glass are balanced so if in the unlikely situation any of the above occurs and the glass breaks, the glass will shatter safely into small thumbnail sized blunt fragments. Please note that some natural misting may occur when you remove this product from its packaging, due to the addition of the glass protection pre-coating. If this does occur this can easily be removed with a soft, dry cloth. No: Description Quantity 3 Wall Plugs mm Screws (Wall Profiles) 6 5 Handle mm Screws 6 7 Screw Cover Caps 12 8 Top Caps 2 9 Seals 2 Equipment Check List: Not Supplied 4.5mm Drill Bit 6mm Masonry Drill Bit 2.5mm Drill Bit Mains or Battery Drill Spirit Level Pozi/Flathead Screw Driver Bathroom Sealant Gun Bathroom Sealant Tube Tape Measure Pencil Pliers Additional fixings if going into plasterboard Before Assembly and Installation of the Pivot Door * Check the product for defects. Installation queries on damaged parts can not be resolved once the installation has been completed. * The Tray must be completely sealed along tiled walls, fitted level (check with a Spirit Level) and should have no leaks. Notes: It is recommended that the Wall Profiles are fitted directly onto tiles or a similar sealed surface. If walls or tray or a combination of both are out of level you will not achieve full adjustment of maximum width. If you have any problems with your Shower Enclosure once installed, please refer back to this Instruction Manual to ensure you have completed every stage correctly. If you still experience any difficulties or have any queries please contact us on +44 (0) for Technical Assistance or +44 (0) for Sales. H2P Aug 12

2 Stage 1 - Check and Seal the Tray Check the tray is level on all sides. Check the tray has been completely sealed between the tiled wall and tray. Note: Ensure the tray is installed as per the manufacturers instructions. Stage 2- Drill the wall profiles and mark the drill hole locations. Drill 3; 4.5mm holes into both wall profiles through the lip see diagram. Locate both profiles 10-15mm from the front of the tray. (The lip of the wall profile should face in towards the enclosure). Using a pencil mark the locations for the drill holes remember the wall profiles will be fixed to the wall through the lip. Make sure the all profiles are completely level. Profile Lip MM Remember if fitting with side panel - locate the wall profiles as shown. Stage 3 - Drilling the Wall Drill the holes using 6mm masonry drill bit. Push the wall plugs into the drilled holes.

3 Stage 4 - Screw-fixing the 1st Wall Profile Apply a bead of silicone the width of the wall profile at the bottom where it will meet the tray and tiled wall. Screw fix the wall profile to the wall using the 35mm screws. Apply a bead of silicone to the inside of the wall profile at the bottom where it meets the tray top. Width of the Wall Profile Inside the Wall Profile (If fitting with a side panel, fix both wall profiles here.) Stage 5 - Fit the handle and Locate the 2nd Wall Profile onto the door. Locate the 2nd Wall profile onto the aluminum profile of the door (see diagram). Fit the door handle (see diagram). (If fitting with a side panel fit the handle only here.) Spacers Fit the Plastic Spacer s between the Glass and Handle

4 Stage 6 - Lift the Door onto the tray and fix the 2nd wall profile. (If fitting with a side panel perform bullet point 2 only - then refer to your side panel instructions). Prior to lifting the door onto the tray, apply a bead of silicone the width of a wall profile, where the 2nd wall profile will meet the tray and tiled wall at the bottom. Lift the door onto the tray and locate it onto the 1st wall profile. Adjust the 2nd wall profile so it locates against the wall and the holes in the profile lip line up with the drilled holes in the wall Using a screw driver screw fix the wall profile to the wall using 35mm screws (supplied). 1st Wall Profile 2nd Wall Profile Width of the Wall Profile Stage 7 - Drilling the Enclosure. Ensure the enclosure is centred between the wall profiles (see diagram). 2.5mm No Gap ensure the magnet seal is locating the full length of the door when in the closed position. Adjust the door within its own main frame to ensure the gap between the top of the door and the horizontal main frame is parallel. To achieve this adjustment, push the main vertical door frame from the top (on the pivot side), further into the wall profile following the arrow. This will ensure the glass door lifts away from the bottom of the main horizontal main frame. (Diagram A) A Drill holes through the wall profiles and into the profiles of the door frame using 2.5mm drill bit. Important: It is critical the door has been adjusted correctly so that the door opens and closes correctly prior to drilling.

5 Stage 8 - Screw Fixing the Enclosure. Using the 12mm screws secure the enclosure to the wall profiles, It is critical the door has been adjusted correctly so that the door opens and closes correctly. There is slight adjustment in the door hinges to help achieve this follow the adjustment instructions below if necessary. When the door is closed, make sure the magnets of the door and frame locate onto each other along the full length. Fit the screw cover caps to conceal the 12mm screw heads. All ways check the screws from the door hinges are tight. Door hinge adjustment: Slide the cover cap down on the back of the hinges. Loosen the screws by approx 2-3 turns, adjust the hinges and glass door so they are level, re-tighten all the screws and replace the hinge cover caps. Take care during this operation -2 persons are recommended when lifting and adjusting the door. Always check the screws from the door hinges are tight. Stage 9 - Sealing the Enclosure and fit the top caps Seal both sides of the wall profiles vertically inside and outside where they meet the tiled walls. Fully seal the base of the enclosure to the tray top from the outside only. Please allow 24 hrs for the sealant to cure prior to using the enclosure. Fit the top caps to the profiles of the door (the caps have a snap-off function to allow a good fit). Important: Failure to follow the sealing procedures correctly may result in serious water damage and will not be covered under the terms of the guarantee.

6 Cleaning your product: Shower Enclosures are designed for luxury showering and with care and attention you can keep them looking new for longer. Simply clean your Shower Enclosure regularly using a soft cloth and warm soapy water and If you live in a hard water area, occasionally clean your Shower Enclosure using a 50/50 solution of white vinegar and water. The solution should be left on the product for approximately 5 mins and then rinsed off using warm water. This method of cleaning should remove lime scale residue. It is also a good idea to wipe all water droplets and residue from the glass surfaces of your Enclosure after use - a window "squeegee" is ideal for this task. This is particularly important in hard-water areas where lime scale build up is likely if water is left on the smooth glass surface for extended periods of time. The use of any other cleaning products is not recommended Proprietary cleaning products frequently change formula without notification and cannot be endorsed for this reason. A List of don ts: Don t use acidic based products. Don t use abrasive cleaners and/or cleaners containing bleach or solvents. Don t use scouring pads, powder or any sharp instruments.