2000 lb. Capacity. Instructions and precautions

Transcription

1 GANTRY CRANE 2000 lb. Capacity Instructions and precautions Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA Visit our website at: Save these instructions. Read all precautions and instructions. Copyright 2008 by Harbor Freight Tools. All rights reserved. No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacement parts, please call

2 Weight Capacity Material Specifications 1 Ton / 2,000 lb. All Steel Construction Adjusting Height ( ) Casters Weight 5 Locking Swivel 265 lb. Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this document as soon as possible Important SAFETY Information General Safety Rules Do not exceed 1 ton (2,000 lb.) weight capacity. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure. Read entire manual, including all safety warnings and operating procedures, before assembling and operating Gantry Crane. Do not use to lift, support or transport humans or animals. Do not use for aircraft purposes. Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents. Keep children and bystanders away while using the Gantry Crane. Be aware of all power lines and other hazards in the work area. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use. Use as intended only; do not modify the Gantry Crane in any way and do not use for anything other than intended purposes. Make sure that only qualified personnel are allowed to operate Gantry Crane Specific Safety Instructions Do not move the Crane when it is under load. The Caster Wheels are not designed to be rolled when the Crane is lifting an object. Do not stand under object that is being lifted. Be aware of the possibility of a load slipping off Crossbeam (19). An item that falls from the Crane may cause serious injury. Make sure load is secured, balanced, and positioned properly in the hook, sling, or lifting device before it is lifted. Make sure load is clear of obstructions, such as stockpiles, machinery, anchors and other obstacles when lifting or moving the load. When moving Crane, avoid sudden acceleration and movements. Verify ground is solid enough to support weight of the Crane when fully loaded. Verify that the Gantry Crane passage is clear. Do not use for side pulling. Operate on flat and level surface only. DO NOT lift loads if the Cross Beam is not level. DO NOT lift if load is swinging. DO NOT lift if the load is not suspended directly under the Cross Beam. DO NOT lift loads over people or allow anyone to walk under an elevated load. DO NOT use unless all assembly points have been inspected and verified. Check for damage and be sure all hardware is tight before EACH use DO NOT leave the loads suspended when the gantry crane is unattended. DO NOT move or load unless Height Adjusting Pins (18) are fully inserted. DO NOT remove, deface, or obscure warnings, caution labels, and capacity labels on Crane. DO NOT use if any parts are bent, have signs of wear or damage, or are missing. Keep the Gantry Crane level at all times. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. SKU For technical questions, please call Page 2

3 Assembly Instructions Read the entire Important Safety Information section at the beginning of this document including all text under subheadings therein before set up or use of this product. Attach four Casters (27) to Base (26). Apply small amount of grease (not included) to zerk fitting of each Caster. See Figure 3, below. Base (26) 1. Attach two Plates (20) to both sides of end of Crossbeam (19), using four Bolts (1), Washers (2), Spring Washers (3), and Nuts (4). Repeat for the other end of Crossbeam. See Figure 1, below. Caster (27) Plate (20) Crossbeam (19) Figure 3 Bolts (1), Washers (2), Spring Washers (3) and Nuts (4) 4. Position an Outer Post (23) at center of Base (26), making certain that the slot at the sides face towards the Casters. See Figure 4, below. Figure 1 2. Attach each Inner Post (21) to the Crossbeam and Plate and fasten together by using eight Bolts, Washers, Spring Washers, and Nuts. See Figure 2, below. Bolts (14) Outer Post (23) Plate (20) Crossbeam (19) Base (26) Bolts (1), Washers (2), Spring Washers (3) and Nuts (4) Inner Post (21) Figure 2 Caster (27) 5. Washers (2), Spring Washers (3) and Nuts (4) Figure 4 From the top, insert two Bolts (14) through bottom of Outer Post and into Base (26). Slip on Washer (2) and Spring Washer (3) and Nuts (4). Secure by tightening Nut. See Figure 4, above. SKU For technical questions, please call Page 3

4 6. Attach two Support Tubes (22) to inner face of each Outer Post (23). Insert the Bolt (5) through top of Support Tube and through eyelet of the Bracket and Support Tube. Slip on a Washer (6), Spring Washer (7) and secure with the Nut (8). See Figure 5, below. 9. Attach Handle (24) to the bracket on the side of Outer Post by inserting the Bolt (10) from the inside and then slipping on Washer (6), Spring Washer (16) and then securing with Nut (11). See Figure 7, below. Support Tubes (22) Bolts (5), Washers (6), Spring Washers (7) and Nuts (8) Bolts (10), Washers (6), Spring Washers (16) and Nuts (11) Bolts (5), Washers (6), Spring Washers (7) and Nuts (8) Outer Post (23) Handle (24) Hook Figure Make sure the two hooks of the Handle engage the two Pins (25). See Figure 8, above. Repeat for other post assembly. Figure 5 7. Attach the other end of Support Tube to the base assembly by the following the steps in Ste 6, above. See Figure 5, above. Repeat for other three Support Tubes 8. Attach Inner Post (21) into Outer Post (23) by inserting Hand Screw (9) all the way through slots and into Inner Post holes. Make sure Inner Post heights on each side are adjusted equally. See Figure 6, below. Handle (24) Hand Screw (9) Hook Safety Pin (25) Figure 8 Support Tube (22) Figure Tighten all Bolts and Nuts securely and make certain entire Telescoping Gantry Crane is tight and secure. Test Gantry Crane before initial use. SKU For technical questions, please call Page 4

5 OPERATION Do not exceed 1 ton (2,000 lb.) weight capacity during use. Attach appropriate trolley or hoist (not included) to Crane crossbeam, making sure it is firmly fastened. Read manual of hoist to verify it can be used with Crane and follow all hoist safety instructions and procedures. Move the Gantry Crane so that it is directly above the item to be lifted. Once in place, lock all the Casters. To raise or lower the Crossbeam (19), two people are required. They should perform the following steps in unison To Lower the Crossbeam: Back off the Hand Screws (9) to free Posts. Lift the Handle (24), attach the Hooks (28) under the idle Height Adjustment Pin (25), raise the handles and remove the load bearing pins. Lower the handles until the pins rest in the well of the height adjustment slot. Remove the hooks, set the idle pins in the adjacent upper holes, attach the hooks to these pins and repeat the above mentioned step until the desired height is reached. See Figure 10, below. To Raise the Crossbeam: 5. Lift up Handles (24) and attach the Hooks (28) to the bottom of the load bearing Pin (18). See Figure 9, below. Pin (25) Handle (24) Figure Figure 9 Unscrew both Hand Screws (9) to release the Inner Posts (21). Remove the Lower Height Pin altogether. Remove idle upper Height Adjustment Pin (25). Force Handles (24) down, lifting the Inner Posts (21) and insert the idle Pin (25) into the exposed pin hole below the elevated pin. Gently lower the Handles (24), allowing the Inner Posts (21) to rest on the Pin (25). Repeat these steps to attain the desired height. Turn all four Hand Screws (9) clockwise to further secure the Inner and Outer posts together. 16. Turn all four Hand Screws (9) clockwise to further secure the Inner and Outer post. MAINTENANCE 1. Before each use, inspect the general condition of the Crane. Check for bent, cracked, worn or damaged parts, loose or missing parts, and any other condition that may affect the Crane s safe operation. If a problem occurs, have it corrected before furhter use. Do not use damaged equipment. 2. To clean, use cloth and mild detergent. Do not use solvents or other flammable agents. When storing, keep Crane in a clean, dry and safe location away from children. 4. CAUTION! All maintenance, serivice, and repairs not discussed in this manual should only be performed by a qualified service technician. SKU For technical questions, please call Page 5

6 Parts List Part Description Qty. 1 Bolt (M12x 25) 24 2 Washer (Ø12) 28 3 Spring Washer (Ø12) 28 4 Nut (M12) 28 5 Bolt (M14x40) 8 6 Washer (Ø14) 8 7 Spring Washer (Ø14) 8 8 Nut (M14) 8 9 Hand Screw 4 10 Bolt (M10x60) 4 11 Nut (M10) 4 12 Bolt (M8x40) 4 13 Nut (M8) 4 14 Bolt (M12x100) 4 15 Bolt (M10x30) 16 Parts List Part Description Qty. 16 Spring Washer (Ø10) Nut (M10) Pin 4 19 Crossbeam 1 20 Plate 4 21 Inner Post 2 22 Support Tube 4 23 Outer Post 2 24 Handle 2 25 Height Adjustment Pin 4 26 Base 2 27 Caster 4 28 Hook 4 29 Safety Rings and Chain 4 Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this document as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. SKU For technical questions, please call Page 6

7 assembly diagram Please Note: Hook (28) and Safety Rings and Chain (29) are not shown. SKU For technical questions, please call Page 7

8 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mission Oaks Blvd. PO Box 6009 Camarillo, CA (800) SKU For technical questions, please call Page 8