Abstract. JZ Reviewed: WCH 7/18/2003. Solution & Interoperability Test Lab Application Notes 2003 Avaya Inc. All Rights Reserved.

Size: px
Start display at page:

Download "Abstract. JZ Reviewed: WCH 7/18/2003. Solution & Interoperability Test Lab Application Notes 2003 Avaya Inc. All Rights Reserved."

Transcription

1 A Sample Configuration using Symbol Client Bridge 1000, Enterasys RoamAbout Wireless Ethernet Adapter, and Avaya AP-3 Wireless Access Point for Avaya IP Telephones - Issue 1.0 Abstract These Application Notes present a sample configuration of Symbol Client Bridge 1000 (CB 1000), Enterasys RoamAbout Wireless Ethernet Adapter, and Avaya TM AP-3 Wireless Access Point to support Avaya TM IP Telephones. The Symbol CB 1000 and the Enterasys RoamAbout Wireless Ethernet Adapter convert any Ethernet-equipped devices, including Avaya TM Series 4600 IP Telephones, into wireless LAN stations. 1 of 19

2 1. Introduction The Symbol CB 1000 and the Enterasys RoamAbout Wireless Ethernet Adapter transform wired computer devices into wireless devices. As shown in Figure 1, Avaya IP telephones 1 and 2 are attached to the Symbol CB 1000 and the Enterasys RoamAbout Wireless Ethernet Adapter respectively, through Ethernet connections. The Avaya AP-3 in the diagram is configured as an b Access Point to serve b clients, i.e. the Symbol CB 1000 and the Enterasys RoamAbout Wireless Ethernet Adapter. Avaya IP telephones 1 and 2 use the DHCP/TFTP server and register to the S8300 Media Server. Wired Equivalent Privacy (WEP) encryption is enabled for the wireless security. See Section 5 for more detailed observations concerning this configuration. Avaya S8300/G700 Symbol Client Bridge 1000 Avaya IP Telephone 1 Avaya P3330T-PWR Switch POE Avaya AP 3 IP: Microsoft DHCP Server Avaya TFTP SERVER Avaya IP Telephone 3 Enterasys RoamAbout Wireless Ethernet Adapter Avaya IP Telephone 2 Figure 1: Wireless Configuration using Avaya AP-3, Symbol CB 1000, and Enterasys RoamAbout Wireless Ethernet Adapter 2 of 19

3 2. Equipment and Software Validated The following equipment and software were used for the sample configuration provided: Equipment Software Avaya S8300 Media Server CM1.2 Avaya P333T-PWR Power Over Ethernet Stackable Switch Avaya 4612 IP Telephones 1.73 Avaya AP-3 Wireless Access Point 2.1.2(412) Symbol Client Bridge Enterasys RoamAbout CSISA-AX Wireless Ethernet Adapter 3.07 Microsoft DHCP server 4.0 Avaya TFTP server Configurations 3.1. Avaya AP-3 Configuration By default, the Avaya AP-3 acts as a DHCP client. As configured in Figure 1, the Avaya AP-3 gets its initial IP address from the DHCP server. To assign a static IP address, run the ScanTool by double clicking ScanTool included on the installation CD on the DHCP server (or any other PC on the same network as the Avaya AP-3). The ScanTool s Scan List window appears (Figure 2): Figure 2: ScanTool List Window for Avaya AP-3 Highlight the Avaya AP-3 identified by its MAC address and click Change. 3 of 19

4 Configure the IP Address Type to Static and enter the IP address, Subnet Mask and Gateway IP address (Figure 3). Enter the Read/Write Password (default: public) and click OK. Note that the static IP address should not be in the IP address pool configured on the DHCP server. Static IP address must be configured for WEB access. Figure 3: ScanTool Change Window for Avaya AP-3 Open a Web browser, enter the Avaya AP-3 s static IP address, and press enter. The Enter Network Password window appears. Enter the HTTP password in the password field and leave the user name field blank. The default http password is public for a new unit. For a new Avaya AP-3 unit, the Setup Wizard will be launched. Click Exit. The following configuration window will appear (Figure 4): 4 of 19

5 Figure 4: Configuration Main Page for Avaya AP-3 5 of 19

6 Click the System tab to enter the proper system information and then click OK (Figure 5). Figure 5: System Configuration for Avaya AP-3 6 of 19

7 Click the Network tab to change or verify the IP configuration (Figure 6): Figure 6: IP Configuration for Avaya AP-3 7 of 19

8 Click the DHCP server sub-tab and make sure that the DHCP server is not enabled (Figure 7). The DHCP server connected to the P330T-PWR in Figure 1 will be used for the Avaya IP telephones. Note that the built-in DHCP server on the Avaya AP-3 cannot be used to support Avaya IP telephones. Figure 7: Disable DHCP server on Avaya AP-3 Click the VLAN sub-tab to change and verify VLAN configuration. VLAN is disabled by default and is not used in the example. Refer to the Avaya AP-3 user guide for VLAN configuration. 8 of 19

9 Click the interfaces tab to configure the wireless-a or wireless-b PC card (Figure 8) (wireless- A is used in the example). Enter Network Name (SSID) and check Enable Closed System. Note that when Enable Closed System is unchecked, a client configured with the Network name ANY can connect to the Avaya AP-3. Click OK when finished. Figure 8: Wireless Interface Configuration for Avaya AP-3 9 of 19

10 Click the Security tab and then Encryption sub-tab (Figure 9). Click the check box Enable Encryption (WEP) for slot A. Type in an Encryption Key 1 of 13 alphanumeric characters for 128-bit encryption. Set Deny Non-Encryption Data to Enable to prevent clients that do not have WEP enabled and the proper keys configured from communicating with the network. Select a key to use for WEP encryption and click OK when finished. Note that the Symbol CB and the Enterasys RoamAbout Wireless Ethernet Adapter support 64-bit and 128-bit encryption. 128-bit encryption is used in the example for strong security. Figure 9: Encryption Configuration for Avaya AP-3 10 of 19

11 As the last step, click the Commands button and Reboot sub-tab (Figure 10). Click Reboot to reboot the Avaya AP-3 for all the changes to take effect. Figure 10: Reboot Avaya AP Symbol CB 1000 Configuration Connect a laptop Ethernet port to the Symbol CB 1000 and run the Configurator Utility by double clicking SYMBOLST on the installation CD. The following Symbol CB Unit List window displays (Figure 11): Figure 11: Symbol CB 1000 Unit List Window 11 of 19

12 Highlight the Symbol CB 1000 and click Configure. The following configuration window displays (Figure 12): Figure 12: Symbol CB 1000 Configuration Window Click on the Radio tab and the Basic sub-tab (Figure 13), enter the same SSID as configured on the Avaya AP-3, enter the Station name, and select Infrastructure for Operating mode. Figure 13: Symbol CB 1000 Radio Configuration: Basic 12 of 19

13 Click the Advanced sub-tab and select dynamic or captured for MAC address and leave the rest of fields as default (Figure 14). Figure 14: Symbol CB 1000 Radio Configuration: Advanced Click the Encryption sub-tab, and check the box Enable encryption (Figure 15). Enter key1, the same key configured on the Avaya AP-3, and set Transmit key to key1. Note that key1 must be copied to key4 in order for 128-bit encryption to work. Figure 15: Symbol CB 1000 Radio Configuration: Encryption Click the Update and Reset Unit button at the bottom of the window. Verify that Wireless LED is lit (Associated (green)/radio Activity (amber)). If the wireless LED is lit, disconnect the laptop from the Symbol CB 1000, connect to an Avaya IP telephone, and reset the Symbol CB The Avaya IP telephone gets its IP address and configuration from the DHCP/TFTP server 13 of 19

14 and registers to the S8300 Media Server if the DHCP/TFTP server is configured properly for the Avaya IP telephone Enterasys RoamAbout Wireless Ethernet Adapter Configuration Insert the RoamAbout CD-ROM into the CD-ROM drive of a laptop and install Enterasys RoamAbout Wireless Ethernet Adapter manager software. Connect the laptop Ethernet port to the Enterasys Ethernet port and start the Enterasys RoamAbout Wireless Ethernet Adapter manger by selecting Start!Program!RoamAbout!Ethernet Adapter manager. The Enterasys RoamAbout Wireless Ethernet Adapter Unit List window appears (Figure 16): Figure 16: Enterasys RoamAbout Wireless Ethernet Adapter Unit List Window Highlight the Enterasys RoamAbout Wireless Ethernet Adapter and click Configure. The following configuration window displays (Figure 17): Figure 17: Enterasys RoamAbout Wireless Ethernet Adapter Configuration Window 14 of 19

15 Click on the Radio tab and the Basic sub-tab (Figure 18). Enter the same Network name (SSID) as configured on the Avaya AP-3, enter the Station name, and select Access Point for Network operation. Figure 18: Enterasys RoamAbout Wireless Ethernet Adapter Radio Configuration: Basic Click the Advanced sub-tab and select dynamic or captured for MAC address (Figure19). Leave the rest of fields as default. Figure 19: Enterasys RoamAbout Wireless Ethernet Adapter Radio Configuration: Advanced 15 of 19

16 Click the Encryption tab, and check the box to Enable Encryption (Figure 20). Enter key1, the same key configured on the Avaya AP-3, and set Transmit key to key1. Figure 20: Symbol CB 1000 Radio Configuration: Encryption Click Update and Reset Unit button at the bottom of the window. Verify that Wireless LED is lit (Associated (green)/radio Activity (amber)). If the wireless LED is lit, disconnect the laptop from the Ethernet, connect to an Avaya IP telephone, and reset the Enterasys RoamAbout Wireless Ethernet Adapter. The Avaya IP telephone gets its IP address and configuration from the DHCP/TFTP server and registers to the S8300 server if the DHCP/TFTP server is configured properly for the Avaya IP telephone DHCP Server Configuration for Avaya IP telephones An Avaya IP telephone gets its IP address and gateway IP address through a DHCP server in the same manner as a PC. The Avaya IP telephone related parameters could be obtained through option number 176 configured on the DHCP server. Refer to Section 7 for a list of related Application Notes. 4. Verification Steps The verification includes two parts: 1. Verify that the wireless LED is green (associated) or amber (Radio Activity) on the Symbol CB 1000 and the Enterasys RoamAbout Wireless Ethernet Adapter. If not, check the association log through the Symbol CB 1000 Configurator Utility or Enterasys RoamAbout Wireless Ethernet Adapter manager by Configure! File! Show Log Window! Association Log (Figure 21): 16 of 19

17 Figure 21: Association Log Verify that the SSID configured on the converter is the same as the Avaya AP-3. If encryption is enabled, verify that the same keys are used on the Avaya AP-3 and the converter. Reset the device after any change is made. 2. If the Avaya IP telephone cannot register to the S8300 Media Server, press mute 2337 and see if the Avaya IP telephone gets its configuration from the DHCP server, i.e. IP address, default router, call server IP address, etc. If not, configure these parameters manually and see if the Avaya IP telephone is registered. If the Avaya IP telephone is registered, troubleshoot the DHCP problem. If the Avaya IP telephone is still not registered, check the forwarding table by Configure! File! Show Log Window! Forward Table (Figure 22): Figure 22: Forward Table Log Verify that the MAC address on the wire interface is the MAC address of the Avaya IP telephone. If not, verify that the MAC address is configured to captured or dynamic in Figure 14 and 19. Reset the converter when finished. If there is no MAC address on radio interface, troubleshoot wireless issues (SSID, WEP, etc). 17 of 19

18 5. Observations Do not attach a PC to an Avaya IP Telephone, which is connected to a Symbol CB 1000 or an Enterasys RoamAbout Wireless Ethernet Adapter. These converters only support one MAC address on their Ethernet interface. Wireless cards from Symbol and Enterasys are required for their converters. Key1 and key 4 must be identical as configured in Figure 15 for 128-bit encryption on a Symbol CB 1000 for the version being tested. 6. Conclusion As illustrated in these Application Notes, the Avaya AP-3 interoperates with the Symbol CB 1000 and the Enterasys RoamAbout Wireless Ethernet Adapter to support Avaya IP telephones with and without encryption (WEP: 64-bit and 128-bit). 7. Additional References Application Notes: 1. Title: Sample Configuration: Avaya MultiVantage Software with an Avaya S8300 Media Server Local Survivable Processor and an Avaya G700 Media Gateway Link: 2. Tile: Layer 2 QoS using Multiple VLANs on a Cajun P130 Workgroup Ethernet Switch with an Avaya TM IP600 Internet Protocol Communication Server and Avaya IP Telephones with attached PCs Link: 18 of 19

19 Avaya and the Avaya Logo are trademarks of Avaya Inc. All trademarks identified by and are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners. The information provided in these Application Notes is subject to change without notice. The configurations, technical data, and recommendations provided in these Application Notes are believed to be accurate and dependable, but are presented without express or implied warranty. Users are responsible for their application of any products specified in these Application Notes. Please any questions or comments pertaining to these Application Notes along with the full title name and filename, located in the lower right corner, directly to the Avaya Solution & Interoperability Test Lab at 19 of 19

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring Enterasys Wireless Access Point 3000 (RBT3K-AG) to Support Avaya IP Office, Avaya IP Wireless Telephones and Avaya Phone Manager

More information

Configuring H.323 over Port Network Address Translation (PNAT) for Avaya IP Endpoints using the Avaya SG200 Security Gateway - Issue 1.

Configuring H.323 over Port Network Address Translation (PNAT) for Avaya IP Endpoints using the Avaya SG200 Security Gateway - Issue 1. Configuring H.323 over Port Network Address Translation (PNAT) for Avaya IP Endpoints using the Avaya SG200 Security Gateway - Issue 1.0 Abstract These Application Notes describe how to configure the Avaya

More information

Preparing the Computers for TCP/IP Networking

Preparing the Computers for TCP/IP Networking Configuration Preparing the Computers for TCP/IP Networking Configuring Windows 98, and ME for TCP/IP Networking Verifying TCP/IP Properties Configuring Windows 2000 or XP for IP Networking Install or

More information

Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0

Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the configuration

More information

Easy Setup Guide for the Sony Network Camera

Easy Setup Guide for the Sony Network Camera -878-191-11 (1) Easy Setup Guide for the Sony Network Camera For setup, a computer running the Microsoft Windows Operating System is required. For monitoring camera images, Microsoft Internet Explorer

More information

1-Port Wireless USB 2.0 Print Server Model # APSUSB201W. Quick Installation Guide. Ver. 2A

1-Port Wireless USB 2.0 Print Server Model # APSUSB201W. Quick Installation Guide. Ver. 2A 1-Port Wireless USB 2.0 Print Server Model # APSUSB201W Quick Installation Guide Ver. 2A Section 1 Step 1Connect one end of the Ethernet cable to the RJ-45 port of the Print Server and attach the other

More information

AP6511 First Time Configuration Procedure

AP6511 First Time Configuration Procedure AP6511 First Time Configuration Procedure Recommended Minimum Configuration Steps From the factory, all of the 6511 AP s should be configured with a shadow IP that starts with 169.254.xxx.xxx with the

More information

NetLINE Wireless Broadband Gateway

NetLINE Wireless Broadband Gateway NetLINE Setup Guide Farallon s NetLINE connects to your cable/dsl modem, allowing computers on your local wired and wireless networks to share a single broadband connection to the Internet. This Setup

More information

Using Cisco UC320W with Windows Small Business Server

Using Cisco UC320W with Windows Small Business Server Using Cisco UC320W with Windows Small Business Server This application note explains how to deploy the Cisco UC320W in a Windows Small Business Server environment. Contents This document includes the following

More information

Quick Start Guide. WRV210 Wireless-G VPN Router with RangeBooster. Cisco Small Business

Quick Start Guide. WRV210 Wireless-G VPN Router with RangeBooster. Cisco Small Business Quick Start Guide Cisco Small Business WRV210 Wireless-G VPN Router with RangeBooster Package Contents WRV210 Router Ethernet Cable Power Adapter Product CD-ROM Quick Start Guide Welcome Thank you for

More information

TE100-P21/TEW-P21G Windows 7 Installation Instruction

TE100-P21/TEW-P21G Windows 7 Installation Instruction Hardware Installation TE100-P21/TEW-P21G Windows 7 Installation Instruction 1. Go to http://www.trendnet.com/downloads/ to download the Windows 7 Utility. Save the file to your desktop. 2. Right click

More information

Configuring the Avaya B179 SIP Conference Phone with Avaya Aura Communication Manager and Avaya Aura Session Manager Issue 1.0

Configuring the Avaya B179 SIP Conference Phone with Avaya Aura Communication Manager and Avaya Aura Session Manager Issue 1.0 Avaya Solution & Interoperability Test Lab Configuring the Avaya B179 SIP Conference Phone with Avaya Aura Communication Manager and Avaya Aura Session Manager Issue 1.0 Abstract These Application Notes

More information

Quick Start Guide. RV 120W Wireless-N VPN Firewall. Cisco Small Business

Quick Start Guide. RV 120W Wireless-N VPN Firewall. Cisco Small Business Quick Start Guide Cisco Small Business RV 120W Wireless-N VPN Firewall Package Contents Wireless-N VPN Firewall Ethernet Cable Power Adapter Quick Start Guide Documentation and Software on CD-ROM Welcome

More information

Cisco - Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW)

Cisco - Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW) Page 1 of 20 Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW) Document ID: 50036 Contents Introduction Prerequisites Requirements Components Used Network Diagram The Role of Switched

More information

Manual Wireless Extender Setup Instructions. Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key

Manual Wireless Extender Setup Instructions. Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key 1 Manual Wireless Extender Setup Instructions Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key Setting up LAN Static IP on PC We need to set up a Static

More information

Quick Installation Guide

Quick Installation Guide 0, Total 18 Quick Installation Guide Sep, 2013 1, Total 18 Thank you for purchasing Enterprise High Gain Outdoor CPE. This manual will instruct you how to configure and manage this CPE, enable you to use

More information

SATO Network Interface Card Configuration Instructions

SATO Network Interface Card Configuration Instructions SATO Network Interface Card Configuration Instructions Table of Contents 1. Reset of wired/wireless interface card... 3 2. Installing the All-In-One Utility (recommended)... 4 3. Configuring wired/wireless

More information

How To Set Up A Computer With A Network Connection On A Cdrom 2.5 (For A Pc) Or Ipad (For Mac) On A Pc Or Mac Or Ipa (For Pc) On An Ipad Or Ipro (

How To Set Up A Computer With A Network Connection On A Cdrom 2.5 (For A Pc) Or Ipad (For Mac) On A Pc Or Mac Or Ipa (For Pc) On An Ipad Or Ipro ( Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, the router automatically enters the self-test phase. During self-test phase, RNX-EasyN400 s Power LED will

More information

N300 WiFi Range Extender WN2000RPT User Manual

N300 WiFi Range Extender WN2000RPT User Manual N300 WiFi Range Extender WN2000RPT User Manual December 2013 202-11333-01 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting NETGEAR products. After installing your device,

More information

by using the Setup Wizard in CD Disk

by using the Setup Wizard in CD Disk How to configure Access Point as Wireless Bridge by using the Setup Wizard in CD Disk Thanks for purchasing Edimax Wireless Access Point. We hope this instruction can help you setup the Wireless Bridge

More information

Installing Cable Modem Software Drivers

Installing Cable Modem Software Drivers Configuration Installing Cable Modem Software Drivers Windows 98SE Operating System Windows Me Operating System Windows 2000 Operating System Windows XP Operating System Wireless LAN Configuration Telnet

More information

WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 4 2014

WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 4 2014 WRE6505 Wireless AC750 Range Extender Version 1.00 Edition 1, 4 2014 2.4G 5G Quick Start Guide User s Guide Default Login Details LAN IP Address 192.168.1.2 User Name admin www.zyxel.com Password 1234

More information

Chapter 1 Configuring Internet Connectivity

Chapter 1 Configuring Internet Connectivity Chapter 1 Configuring Internet Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration

More information

WLAN Outdoor CPE For 2.4G. Quick Installation Guide

WLAN Outdoor CPE For 2.4G. Quick Installation Guide WLAN Outdoor CPE For 2.4G Quick Installation Guide Part I: External Installation Direction A. Check the parts in your box CPE SET 1 DC 12V/1.5A Power Adapter 1 PoE DC Injector 1 Hose Clamps 2 Manual &

More information

Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0

Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0 Abstract These Application Notes describe the configuration

More information

Wireless-N. User Guide. PCI Adapter WMP300N (EU) WIRELESS. Model No.

Wireless-N. User Guide. PCI Adapter WMP300N (EU) WIRELESS. Model No. 2,4 GHz WIRELESS Wireless-N PCI Adapter User Guide Model No. WMP300N (EU) Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of

More information

StarMOBILE Network Configuration Guide. A guide to configuring your StarMOBILE system for networking

StarMOBILE Network Configuration Guide. A guide to configuring your StarMOBILE system for networking StarMOBILE Network Configuration Guide A guide to configuring your StarMOBILE system for networking INTRODUCTION... 3 BEFORE YOU BEGIN... 3 1) CONFIRM YOU HAVE THE LATEST SOFTWARE... 3 2) INSTALL THE STARMOBILE

More information

Link Link sys E3000 sys RE1000

Link Link sys E3000 sys RE1000 User Guide High Performance Extender Wireless-N Router Linksys Linksys RE1000 E3000Wireless-N Table of Contents Contents Chapter 1: Product Overview 1 Front 1 Top 1 Bottom 1 Back 2 Chapter 2: Advanced

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring a Small to Medium Size Business VoIP and Data Network Solution Consisting of HP ProCurve Networking Switches and an Avaya Telephony

More information

Network Setup & Options

Network Setup & Options 3.0 Network Setup & Options 3.3 TABLE OF CONTENTS 3.1 INTRODUCTION... 5 3.2 DISABLING NETWORK SECURITY SETTINGS... 6 3.2.1 Aftermarket Internet Security and Firewalls... 6 3.2.2 Windows Firewall... 6

More information

How to configure your Thomson SpeedTouch 780WL for ADSL2+

How to configure your Thomson SpeedTouch 780WL for ADSL2+ How to configure your Thomson SpeedTouch 780WL for ADSL2+ Connecting up your router This guide assumes that you have successfully: unpacked your router connected it up to your phone socket using the DSL

More information

Installing Windows 95 Drivers and Utilities for the Cisco Aironet 340/350 Series Client Adapters

Installing Windows 95 Drivers and Utilities for the Cisco Aironet 340/350 Series Client Adapters Installing Windows 95 Drivers and Utilities for the Cisco Aironet 340/350 Series Client Adapters Document ID: 12134 You need a valid Cisco.com account in order to download Cisco Aironet drivers, firmware,

More information

Integrating a Hitachi IP5000 Wireless IP Phone

Integrating a Hitachi IP5000 Wireless IP Phone November, 2007 Avaya Quick Edition Integrating a Hitachi IP5000 Wireless IP Phone This application note explains how to configure the Hitachi IP5000 wireless IP telephone to connect with Avaya Quick Edition

More information

PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400

PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Outdoor Series: Surf AP 200/400-X, PolePoint 400-X, Surf 400-DX User Manual Document Rev. 1.2 July 07 COPYRIGHT & TRADEMARKS

More information

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. PCI Adapter with RangeBooster. User Guide WIRELESS WMP54GR. Model No.

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. PCI Adapter with RangeBooster. User Guide WIRELESS WMP54GR. Model No. A Division of Cisco Systems, Inc. GHz 2.4 802.11g WIRELESS Wireless-G PCI Adapter with RangeBooster User Guide Model No. WMP54GR Copyright and Trademarks Specifications are subject to change without notice.

More information

Configuring Check Point VPN-1/FireWall-1 and SecuRemote Client with Avaya IP Softphone via NAT - Issue 1.0

Configuring Check Point VPN-1/FireWall-1 and SecuRemote Client with Avaya IP Softphone via NAT - Issue 1.0 Configuring Check Point VPN-1/FireWall-1 and SecuRemote Client with Avaya IP Softphone via NAT - Issue 1.0 Abstract Avaya IP Softphone R3 V2.1 now supports H.323 VoIP applications running over different

More information

SOHO 6 Wireless Installation Procedure Windows 95/98/ME with Internet Explorer 5.x & 6.0

SOHO 6 Wireless Installation Procedure Windows 95/98/ME with Internet Explorer 5.x & 6.0 SOHO 6 Wireless Installation Procedure Windows 95/98/ME with Internet Explorer 5.x & 6.0 Before You Begin Before you install the SOHO 6 Wireless, you must have: A computer with a 10/100BaseT Ethernet card

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring a Virtual Private Network (VPN) for Avaya IP Office using the Edgewater Networks EdgeMarc 4500 VoIP VPN Appliance - Issue 1.0

More information

Avaya Wireless AP Device Manager User Guide

Avaya Wireless AP Device Manager User Guide Avaya Wireless AP Device Manager User Guide February 2003 Avaya Wireless AP Device Manager User Guide Copyright Avaya Inc. 2003 ALL RIGHTS RESERVED The products, specifications, and other technical information

More information

Customer Installation Guide NBG-4615 v2 ZyXEL Wireless Router

Customer Installation Guide NBG-4615 v2 ZyXEL Wireless Router Customer Installation Guide NBG-4615 v2 ZyXEL Wireless Router Form #496PTC Rev. 09/2013 Hardware Installation 1. First, connect the DSL modem to the WAN port, located on the back of the NBG-4615 v2, on

More information

Linksys WAP300N. User Guide

Linksys WAP300N. User Guide User Guide Contents Contents Overview Package contents 1 Back view 1 Bottom view 2 How to expand your home network 3 What is a network? 3 How to expand your home network 3 Where to find more help 3 Operating

More information

Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)

Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode) En Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode) Windows XP This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 computer

More information

Configuring Routers and Their Settings

Configuring Routers and Their Settings Configuring Routers and Their Settings When installing a router on your home network the routers settings are usually defaulted to automatically protect your home, and simplify setup. This is done because

More information

Application Notes for Lucent Technologies VitalQIP DHCP/DNS Management with Avaya IP Telephones and Avaya Communication Manager Issue 1.

Application Notes for Lucent Technologies VitalQIP DHCP/DNS Management with Avaya IP Telephones and Avaya Communication Manager Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Lucent Technologies VitalQIP DHCP/DNS Management with Avaya IP Telephones and Avaya Communication Manager Issue 1.0 Abstract These Application

More information

2 Setting Up the Hardware for a Wired Ethernet Network... 13. 3 Setting Up the Software for an Ethernet Network... 21

2 Setting Up the Hardware for a Wired Ethernet Network... 13. 3 Setting Up the Software for an Ethernet Network... 21 Contents 1 Networking Basics............................................... 1 Selecting a network connection........................................ 2 Wired Ethernet network...........................................

More information

Step-by-Step Setup Guide Wireless File Transmitter FTP Mode

Step-by-Step Setup Guide Wireless File Transmitter FTP Mode EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Infrastructure Setup Windows XP 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without permission is prohibited.

More information

Quick Installation Guide

Quick Installation Guide Quick Installation Guide (For Windows & Mac OS) Outdoor Wireless IP Camera Package Contents V1.1 IP Camera Power Adapter Resource CD Ethernet Cable Mounting Bracket(except FI8919) Wi-Fi Antenna Quick Installation

More information

DWL-2000AP. Before You Begin. Check Your Package Contents

DWL-2000AP. Before You Begin. Check Your Package Contents This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DWL-2000AP D-Link AirPlus Xtreme G TM Wireless Access Point Before You Begin It s best to

More information

The Wireless LAN (Local Area Network) USB adapter can be operated in one of the two following networking configurations :

The Wireless LAN (Local Area Network) USB adapter can be operated in one of the two following networking configurations : SAGEM Wi-Fi 11g USB ADAPTER Quick Start Guide About this guide This Quick Start Guide describes how to install and operate your SAGEM Wi-Fi 11g USB ADAPTER. Please read this manual before you install the

More information

Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.

Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance. Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance. Connect to the Access Point with the Ethernet cable or via wireless.the

More information

Application Notes for Valcom PagePro IP with Avaya IP Office Issue 1.0

Application Notes for Valcom PagePro IP with Avaya IP Office Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Valcom PagePro IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required for Valcom PagePro

More information

POWERLINK High Power Wireless LAN 802.11b/g/n USB Adapter User Manual

POWERLINK High Power Wireless LAN 802.11b/g/n USB Adapter User Manual Before you proceed with the installation, please notice the following descriptions. Note 1: The following installation was operated under Windows XP. (Procedures are similar for Windows 98SE/Me/2000.)

More information

Lab 8.4.5.1 Configuring LEAP/EAP using Local RADIUS Authentication

Lab 8.4.5.1 Configuring LEAP/EAP using Local RADIUS Authentication Lab 8.4.5.1 Configuring LEAP/EAP using Local RADIUS Authentication Objective Topology Estimated Time: 40 minutes Number of Team Members: Students can work in teams of two. In this lab, the student will

More information

Application Notes for Configuring a SonicWALL Continuous Data Protection (CDP) backup solution with Avaya VoiceMail Pro - Issue 1.

Application Notes for Configuring a SonicWALL Continuous Data Protection (CDP) backup solution with Avaya VoiceMail Pro - Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Configuring a SonicWALL Continuous Data Protection (CDP) backup solution with Avaya VoiceMail Pro - Issue 1.0 Abstract These Application

More information

Installation Guide Wireless 4-Port USB Sharing Station. GUWIP204 Part No. M1172-a

Installation Guide Wireless 4-Port USB Sharing Station. GUWIP204 Part No. M1172-a Installation Guide Wireless 4-Port USB Sharing Station 1 GUWIP204 Part No. M1172-a 2011 IOGEAR. All Rights Reserved. PKG-M1172-a IOGEAR, the IOGEAR logo, MiniView, VSE are trademarks or registered trademarks

More information

NETVIGATOR Wireless Modem Setup Guide. (TG789Pvn)

NETVIGATOR Wireless Modem Setup Guide. (TG789Pvn) NETVIGATOR Wireless Modem Setup Guide (TG789Pvn) Configure the NETVIGATOR Wireless Modem Make sure that system meets the following requirement prior to NETVIGATOR Wireless Modem usage: - Subscribers who

More information

Application Notes for the GN Netcom GN 8120 USB Headset Adapter with Avaya IP Softphone Issue 1.0

Application Notes for the GN Netcom GN 8120 USB Headset Adapter with Avaya IP Softphone Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for the GN Netcom GN 8120 USB Headset Adapter with Avaya IP Softphone Issue 1.0 Abstract These Application Notes describe a compliance-tested

More information

Configuring the WT-4 for Upload to a Computer (Infrastructure Mode)

Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) En Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Windows XP This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2

More information

The following sections describe the Gateway configuration pages in the SBG1000 Setup Program.

The following sections describe the Gateway configuration pages in the SBG1000 Setup Program. Configuration Gateway > WAN Page Gateway: LAN nat config Page Gateway: LAN dhcp server config Page Gateway LOG Page Preparing the Network Preparing the Computers for TCP/IP Networking Configuring TCP/IP

More information

STATIC IP SET UP GUIDE

STATIC IP SET UP GUIDE STATIC IP SET UP GUIDE VERIZON D-LINK 2750B & ACTIONTEC GT784 WNV WIRELESS GATEWAY Verizon High Speed Internet for Business Verizon High Speed Internet for Business YOUR NEW STATIC IP CONNECTION AND SET

More information

Pre-lab and In-class Laboratory Exercise 10 (L10)

Pre-lab and In-class Laboratory Exercise 10 (L10) ECE/CS 4984: Wireless Networks and Mobile Systems Pre-lab and In-class Laboratory Exercise 10 (L10) Part I Objectives and Lab Materials Objective The objectives of this lab are to: Familiarize students

More information

Configuring the WT-4 for ftp (Ad-hoc Mode)

Configuring the WT-4 for ftp (Ad-hoc Mode) En Configuring the WT-4 for ftp (Ad-hoc Mode) Mac OS X Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Mac OS X (10.5.2) ftp server for transmission

More information

Quick Installation Guide

Quick Installation Guide V48.01 Model: FI8919W Quick Installation Guide Outdoor Pan/Tilt Wireless IP Camera For Windows OS ------- Page 1 For MAC OS ------- Page 15 ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation

More information

Configuring the WT-4 for Upload to a Computer (Infrastructure Mode)

Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 1 of 25 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Windows 7 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) This document provides basic instructions

More information

IS SERIES. QuikStart Programming Guide. IP Network Direct System. Programming Videos

IS SERIES. QuikStart Programming Guide. IP Network Direct System. Programming Videos 0215 IS SERIES IP Network Direct System QuikStart Programming Guide 1 4 GHI 2 ABC 5 JKL 3 DEF 6 MNO PRIVACY TRANSFER LIST SETTING 7 PQRS 8 TUV 9 WXYZ ZOOM 0 # WIDE Programming Videos ATTENTION: This is

More information

UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY)

UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY) UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY) Hardware Installation 1. Initial placement for programming and configuration purposes should be performed in an indoor environment.

More information

Experience Next-Generation WiFi

Experience Next-Generation WiFi Do More Experience Next-Generation WiFi Your new WiFi extender supports the 802.11ac networking standard. This new standard offers better speed, improved reliability, and more range than older WiFi networking

More information

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. USB Network Adapter with RangeBooster. User Guide WIRELESS WUSB54GR. Model No.

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. USB Network Adapter with RangeBooster. User Guide WIRELESS WUSB54GR. Model No. A Division of Cisco Systems, Inc. GHz 2.4 802.11g WIRELESS Wireless-G USB Network Adapter with RangeBooster User Guide Model No. WUSB54GR Copyright and Trademarks Specifications are subject to change without

More information

Chapter 1 Installing the Gateway

Chapter 1 Installing the Gateway Chapter 1 Installing the Gateway This chapter describes how to set up the wireless voice gateway on your Local Area Network (LAN), connect to the Internet, and perform basic configuration. For information

More information

Step-by-Step Setup Guide Wireless File Transmitter FTP Mode

Step-by-Step Setup Guide Wireless File Transmitter FTP Mode EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Ad Hoc Setup Windows XP 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without permission is prohibited. 1

More information

Turn on all of your network devices and then check to see if the LEDs on the Access Point display normally as the diagram below describes.

Turn on all of your network devices and then check to see if the LEDs on the Access Point display normally as the diagram below describes. Connect to the Access Point with the Ethernet cable or via wireless. The default SSID of the Access Point is TP-LINK_ XXXXXX. The XXXXXX is the last 6 characters of the Access Point s MAC address. Plug

More information

User guide for NANOSTATION 2

User guide for NANOSTATION 2 User guide for NANOSTATION 2 1. Connecting hardware. Connecting your Nanostation 2 to your network is very easy, as it s using the POE (Power Over Ethernet) technology. For this you will need two direct

More information

Software Installation Guide

Software Installation Guide Software Installation Guide This manual explains how to install the software over a USB or network connection. Network connection is not available for models SP 200/200S/203S/203SF/204SF. To manually configure

More information

DWL-G710 Wireless Range Extender. Ethernet (CAT5e UTP/Straight-Through) Cable

DWL-G710 Wireless Range Extender. Ethernet (CAT5e UTP/Straight-Through) Cable This product can be set up using any curren ent t web browser owser,, i.e.,., Internet Explorer 6 or Netscape Navigator 6.2.3. DWL-G710 D-Link AirPlus G Wireless Range Extender Befor ore You Begin It s

More information

Configuring an A Series LED Sign Controller for your Network

Configuring an A Series LED Sign Controller for your Network Configuring an A Series LED Sign Controller for your Network A Series LED displays from Optec support both serial and 10BaseT Ethernet communication. Serial communication via RS232 or RS485 is independent

More information

Configure WorkGroup Bridge on the WAP131 Access Point

Configure WorkGroup Bridge on the WAP131 Access Point Article ID: 5036 Configure WorkGroup Bridge on the WAP131 Access Point Objective The Workgroup Bridge feature enables the Wireless Access Point (WAP) to bridge traffic between a remote client and the wireless

More information

TECH BULLETIN NETGEN1 DOOR CONTROLLER WI-FI NETWORK CONFIG

TECH BULLETIN NETGEN1 DOOR CONTROLLER WI-FI NETWORK CONFIG TECH BULLETIN NETGEN1 DOOR CONTROLLER WI-FI NETWORK CONFIG February 12, 2008 The factory default network configuration for BlueWave Security s Wi-Fi NetGen1 door controllers is a dynamic DHCP IP address,

More information

Assign a static IP address (192.168.1.100) for your computer. Please refer to T3 in Troubleshooting guide on page 10 if you need assistance.

Assign a static IP address (192.168.1.100) for your computer. Please refer to T3 in Troubleshooting guide on page 10 if you need assistance. Assign a static IP address (192.168.1.100) for your computer. Please refer to T3 in Troubleshooting guide on page 10 if you need assistance. You may need to write down the original settings as a backup.

More information

Quick Installation Guide of WLAN Broadband Router

Quick Installation Guide of WLAN Broadband Router To avoid users without access right through your WLAN Broadband Router, suggest that use security mechanism like WEP, WPA or set ID/password for web configuration login IP address 192.168.1.254. Preparation

More information

Movie Cube. User s Guide to Wireless Function

Movie Cube. User s Guide to Wireless Function Movie Cube User s Guide to Wireless Function Table of Contents 1. WLAN USB Adapter Connection...3 2. Wireless Setup...4 2.1 Infrastructure (AP)...5 2.2 Peer to Peer (Ad Hoc)...7 2.3 Settings for PC...8

More information

Chapter 3 Connecting the Router to the Internet

Chapter 3 Connecting the Router to the Internet Chapter 3 Connecting the Router to the Internet This chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to configure your DG834GT

More information

Configuring the WT-4 for ftp (Ad-hoc Mode)

Configuring the WT-4 for ftp (Ad-hoc Mode) En Configuring the WT-4 for ftp (Ad-hoc Mode) Windows XP Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 ftp server

More information

Networking. General networking. Networking overview. Common home network configurations. Wired network example. Wireless network examples

Networking. General networking. Networking overview. Common home network configurations. Wired network example. Wireless network examples Networking General networking Networking overview A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for communication

More information

Chapter 1 Connecting the Router to the Internet

Chapter 1 Connecting the Router to the Internet Chapter 1 Connecting the Router to the Internet This chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to set up your wireless ADSL

More information

Motorola AP-5131 Access Point Quick Setup Guide

Motorola AP-5131 Access Point Quick Setup Guide Motorola AP-5131 Access Point Quick Setup Guide Ishida / Rice Lake Wireless Communications P/N 109422 Getting Started 1. These instructions were written for the AP-5131 using firmware version 1.1.0.0-045R.

More information

Application Notes for the Ingate SIParator with Avaya Converged Communication Server (CCS) - Issue 1.0

Application Notes for the Ingate SIParator with Avaya Converged Communication Server (CCS) - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for the Ingate SIParator with Avaya Converged Communication Server (CCS) - Issue 1.0 Abstract These Application Notes describe the configuration

More information

Connecting to the Internet. LAN Hardware Requirements. Computer Requirements. LAN Configuration Requirements

Connecting to the Internet. LAN Hardware Requirements. Computer Requirements. LAN Configuration Requirements Connecting to the Internet LAN Hardware Requirements Computer Requirements LAN Configuration Requirements Installation Performed by Time Warner Cable Technician Connecting via Ethernet Connecting via USB

More information

FI8910W Quick Installation Guide. Indoor MJPEG Pan/Tilt Wireless IP Camera

FI8910W Quick Installation Guide. Indoor MJPEG Pan/Tilt Wireless IP Camera Model: FI8910W Quick Installation Guide (For Windows OS) (For MAC OS please go to page 17) Indoor MJPEG Pan/Tilt Wireless IP Camera Black White Package Contents IP Camera FI8910W with IR-Cut.x 1 DC Power

More information

Application Notes for Integrating Verint ULTRA9 VoIP Call Recording Service With Avaya Interaction Center - Issue 1.1

Application Notes for Integrating Verint ULTRA9 VoIP Call Recording Service With Avaya Interaction Center - Issue 1.1 Avaya Solution & Interoperability Test Lab Application Notes for Integrating Verint ULTRA9 VoIP Call Recording Service With Avaya Interaction Center - Issue 1.1 Abstract Verint Ultra Intelligent Recording

More information

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification: PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,

More information

Chapter 1 Configuring Basic Connectivity

Chapter 1 Configuring Basic Connectivity Chapter 1 Configuring Basic Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration

More information

NBG2105. User s Guide. Quick Start Guide. Wireless Mini Travel Router. Default Login Details. Version 1.00 Edition 1, 11/2012

NBG2105. User s Guide. Quick Start Guide. Wireless Mini Travel Router. Default Login Details. Version 1.00 Edition 1, 11/2012 NBG2105 Wireless Mini Travel Router Version 1.00 Edition 1, 11/2012 Quick Start Guide User s Guide LAN IP Address Default Login Details 192.168.1.1 (Router Mode) 192.168.1.2 (Other Modes) Passwordwww.zyxel.com

More information

Chapter 4 Customizing Your Network Settings

Chapter 4 Customizing Your Network Settings . Chapter 4 Customizing Your Network Settings This chapter describes how to configure advanced networking features of the Wireless-G Router Model WGR614v9, including LAN, WAN, and routing settings. It

More information

Quick Start Guide. WAP371 Wireless AC/N Dual Radio Access Point with Single Point Setup Quick Start Guide. Cisco Small Business

Quick Start Guide. WAP371 Wireless AC/N Dual Radio Access Point with Single Point Setup Quick Start Guide. Cisco Small Business Quick Start Guide Cisco Small Business WAP371 Wireless AC/N Dual Radio Access Point with Single Point Setup Quick Start Guide Versión en Español para México en el CD Version en français sur CD Versione

More information

Wireless Network Configuration Guide

Wireless Network Configuration Guide CIT Table of Contents Introduction... 1 General Wireless Settings... 1 1. Windows XP Wireless Configuration... 2 2. Windows XP Intel Pro Wireless Tool... 7 3. Windows Vista Using the Windows Wireless Tools...

More information

Mobile Router MR600 User Guide

Mobile Router MR600 User Guide Mobile Router MR600 User Guide HANTZ + PARTNER The Upgrade Company! www.hantz.com 1. Connections and LEDS The following pictures show you various connectors and status LED indicators on the MR600 Mobile

More information

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. PCI Adapter. User Guide WIRELESS WMP54G. Model No.

A Division of Cisco Systems, Inc. GHz 2.4 802.11g. Wireless-G. PCI Adapter. User Guide WIRELESS WMP54G. Model No. A Division of Cisco Systems, Inc. GHz 2.4 802.11g WIRELESS Wireless-G PCI Adapter User Guide Model No. WMP54G Copyright and Trademarks Specifications are subject to change without notice. Linksys is a

More information

Intel Active Management Technology with System Defense Feature Quick Start Guide

Intel Active Management Technology with System Defense Feature Quick Start Guide Intel Active Management Technology with System Defense Feature Quick Start Guide Introduction...3 Basic Functions... 3 System Requirements... 3 Configuring the Client System...4 Intel Management Engine

More information

Wireless USB Adapter

Wireless USB Adapter Wireless USB Adapter User s Manual 1 Table of Contents USER S MANUAL... 1 WELCOME... 3 PACKAGE CONTENTS... 3 WIRELESS USB ADAPTER OVERVIEW... 4 INTERFACE... 4 LED DESCRIPTION... 4 WPS BUTTON... 4 WIRELESS

More information

Configuring Your Network s Security

Configuring Your Network s Security Configuring Your Network s Security Security is an important issue when using a wireless home network. Because radio waves are used to transfer information between your networked computers, it's possible

More information