Installation BUILDING REGULATIONS

Transcription

1

2 The OPAL plastic pipe collar is a powder coated mild steel or stainless steel casing containing OPAL graphite intumescent layers for Polypropylene, Polyethylene and ABS plastic pipes. OPAL intumescent is also suitable for upvc pressure and non-pressure pipes. These layers expand at approximately 150 o C to crush the softening plastic pipe and thereby close the penetrations through fire rated walls and floors. The OPAL fire collars can be surface mounted and they can be cast in when fixing space is not available. Fixing is with non-combustible metal screws, anchor or cavity fixings. The OPAL fire collar is fully tested for upvc, Polypropylene, Polyethylene and ABS plastic pipes for both wall and floor penetrations. and floors, OPAL fire collars have been tested at Warrington Fire Research Centre and Building Research Establishment Ltd. (BRE) to BS476 Part and Station d essais CTICM 98-E-275 for wall collars and 98-H-276 for floor collars. OPAL fire collars meet both integrity and insulation requirements to this standard for both two and four hours, when surface mounted and cast in a concrete floor or in a masonry or blockwork wall. Surface mounted to wall Surface mounted to floor The OPAL fire collar can be used through plasterboard, concrete, blockwork and brickwork constructions. The OPAL fire collar has achieved performance from 2 to 4 hours in tests to relevant British standards at approved laboratories. OPAL fire collars are available in all pipe sizes up to 315mm dia. (Remark: Size not mention may be Specially offered by the Manufacturer.) BUILDING REGULATIONS Installation OPAL fire collars must be fitted on each side of a wall where both sides are at risk from fire. Penetrations through floors require an OPAL fire collar fitted to the underside only of each penetration. Non-flammable screws, anchor or cavity fixings must be used to secure OPAL fire collars to walls and floors. To satisfy building regulation requirements on all penetrating fire rated compartment walls

3 Surface Mounted Type Full Cast In Type Surface Mounted Type Surface Mounted Type Availability of Fire Collars upvc Polyprop Polyeth ABS Nominal BS 5255 BS 4514 BS 3505 (JIS K6741/2) Surface Cast In 2 hr 2 hr 2 hr Dia. 2 hr 4 hr 2 hr 4 hr 2 hr 4 hr 15 mm * * 20 mm * * 25 mm * * 30 mm * * * * * 32 mm * * * * 40 mm * * * * * * * * * 50 mm * * * * 55 mm * * * * * 63 mm * * * * * 65 mm * * 75 mm * * * * * 80 mm * * * * 82 mm * * * * * 90 mm * * * * * 100 mm * * * * 110 mm * * * * * 125 mm * * * * * * * 140 mm * * * * * 150 mm * * * * 160 mm * * * * * * * 175 mm * * 200 mm * * 225 mm * * 300 mm * *

4 2 Hours Fire Collars Height Fixing Lug Details for fixing upvc Pipes to BS5255/BS4514 Nominal Actual Minimum Total Collar Total Available Recommended Diameter Outside Number of Thickness of Height Number of Min. No. Min. Sizing of of Pipe Diameter Intumescent Intumescent (2 Hours) Fixing Lugs of Fixing Mild Steel Anchor of Pipe Layer Lugs for Mounting (2 Hours) M3 x 25mm M3 x 25mm * M5 x 25mm * M5 x 25mm * M5 x 25mm * M5 x 25mm Remark: All Dimension in (mm) * 60mm Collar Height is available upon request. Details for fixing upvc Pipes to BS3505 Nominal Actual Minimum Total Collar Total Available Recommended Diameter Outside Number of Thickness of Height Number of Min. No. Min. Sizing of of Pipe Diameter Intumescent Intumescent (2 Hours) Fixing Lugs of Fixing Mild Steel Anchor of Pipe Layer Lugs for Mounting (2 Hours) M3 x 25mm M3 x 25mm M3 x 25mm M3 x 25mm M5 x 25mm M5 x 25mm M5 x 25mm M5 x 25mm M5 x 25mm Remark: All Dimension in (mm)

5 2 Hours Opal Stainless Steel Fire Collar Height Fixing Lug Details for fixing upvc Pipes to BS5255/BS4514 Nominal Actual Minimum Total Collar Total Available Recommended Diameter Outside Number of Thickness of Height Number of Min. No. Min. Sizing of of Pipe Diameter Intumescent Intumescent (2 Hours) Fixing Lugs of Fixing Mild Steel Anchor of Pipe Layer Lugs for Mounting (2 Hours) M3 x 25mm M3 x 25mm * M5 x 25mm * M5 x 25mm * M5 x 25mm * M5 x 25mm Remark: All Dimension in (mm) * 60mm Collar Height is available upon request. Details for fixing upvc Pipes to BS3505 Nominal Actual Minimum Total Collar Total Available Recommended Diameter Outside Number of Thickness of Height Number of Min. No. Min. Sizing of of Pipe Diameter Intumescent Intumescent (2 Hours) Fixing Lugs of Fixing Mild Steel Anchor of Pipe Layer Lugs for Mounting (2 Hours) M3 x 25mm M3 x 25mm M3 x 25mm M3 x 25mm M5 x 25mm M5 x 25mm M5 x 25mm M5 x 25mm M5 x 25mm Remark: All Dimension in (mm)

6

7 2 Hours Pipe Wraps Height Intumescent Length Details for fixing upvc Pipes to BS5255/BS4514 Nominal Actual Number of Total Height of Minimum Diameter Outside Intumescent Thickness of Intumescent Length of of Pipe Diameter Layer Intumescent (2 Hours) Intumescent of Pipe (2 Hours) Remark: All Dimension in (mm) Details for fixing upvc Pipes to BS3505 Nominal Actual Number of Total Height of Minimum Diameter Outside Intumescent Thickness of Intumescent Length of of Pipe Diameter Layer Intumescent (2 Hours) Intumescent of Pipe (2 Hours) Remark: All Dimension in (mm) Note: The plastic bag with self adhesive tape is our original design for ease of installation. It can be removed away subject to project requirement. But our above required number of intumescent layers must be strictly followed and used to ensure the fire resistance performance.

8 INTUMESCENT TECHNICAL DATA COLOUR CONSISTANCY DENSITY WEIGHT FIRE PERFORMANCE EXPANSION TEMPERATURE EXPANSION RATE EXPANSION PRESSURE THORN FLEXIBILITY RESISTANCE TO UV RADIATION HEAT CONDUCTIVITY HUMIDITY CHARACTERISTICS ANTHRACITE GREY SOLID, FLEXIBLE 1 +/- 0.2 g/cm 2.5 mm THICKNESS: 2.5 +/- 0.3kg/M CLASSIFICATION B1 (DIN 4102) START AT APPROX. 150 C MINIMUM 7:1 (15 min./300 C) MINIMUM 0.6N/mm MINI. 7:1 (15 min./300 C) 3 EXCELLENT 1.2 W/mK (UNEXPANDED) INSOLUBLE IN WATER 2 O O O 2 BUN KEE (INTERNATIONAL) LIMITED OFF. ADD. :12/F., PHASE 1, AUSTIN TOWER, AUSTIN AVENUE,TSIM SHA TSUI, KOWLOON, HONG KONG. TEL. : (852) (16 LINES) FAX: (852) SHOP : 1) G/F., 618 SHANGHAI STREET, KOWLOON. 2) G/F., 30 HOP YICK ROAD, YUEN LONG. 3) SHOP A, G/F., 7-11 TAI WONG ST., EAST, WAN CHAI. GODOWN : LOT 3719 IN DD 104, YUEN LONG, N.T. sales@bunkeeintl.com.hk

9 Installation Manual For OPAL Fire Collars METAL PIPE SLEEVE SEALANT STEP 1. BACK FILL THE GAP WITH MASTIC / MORTAR OR MINERAL WOOL BETWEEN upvc PIPE AND METAL PIPE SLEEVE. ADD SEALANT / JOINT FILLER FOR FINISHING STEP 2. STICK THE FIRE COLLAR TO THE CEILING OR WALL AND TEMPORARY LOCK IT ON THE PIPE STEP 3. MARK AND DRILL THE HOLES ON CEILING OR WALL MATCHING WITH FIXING LUGS ACCORDINGLY STEP 4. LOCK THE FIRE COLLAR AND FASTEN

10 Installation Manual For OPAL Pipe Wraps METAL PIPE SLEEVE STEP 1. CLEAN UP THE UPVC PIPE AND STICK THE PIPE WRAP AROUND THE PIPE STEP 2. GLIDE THE PIPE WRAP INTO THE OPENING OF CEILING / FLOOR SLAB OR WALL SEALANT STEP 3. BACK FILL THE OPENING WITH THE MASTIC / MORTAR OR MINERAL WOOL POINTING SURROUND THE UPVC PIPE STEP 4. CLEAN UP THE UPVC PIPE AND ADD SEALANT / JOINT FILLER FOR FINISHING